RS PRO Linear Actuators
RS Stock No.: 177-4514
Features
- Compact Design
- Preset Limit Switches
- Hall Effect Sensors
- Input Voltage 24VDC
- Stroke 100mm
- IP42
- Duty Cycle 10%
The RS PRO Linear Actuator is described as a quiet and powerful actuator capable of up to 6000N thrust, suitable for furniture applications.
RS PRO is the own brand of RS. The RS PRO Seal of Approval is your assurance of professional quality, a guarantee that every part is rigorously tested, inspected, and audited against demanding standards. Making RS PRO the Smart Choice for our customers.
Product Description
The FD60 is a quiet and powerful actuator designed for furniture applications, providing up to 6000N of thrust. Its main application is in furniture.
General Specifications
| Actuator Type | ACME Screw |
| Motor Technology | DC Motor |
| Control | S - Limit Switch, H - Hall Effect Sensor |
| Series | FD60 |
| Colour | Black & Silver |
| Duty Cycle | 10% or 2 min of continuous operation in 20 min. |
| Housing | Plastic moldings, aluminum cover tube |
Electrical Specifications
| Input Voltage | 24VDC |
| Current No Load | 0.6A at 24VDC |
| Current Full Load | 2.7A at 24VDC |
| Motor Power | 64W |
| Maximum Acceleration | N/A |
| Maximum Load | 6000N Push/Pull |
| Maximum Speed No Load | 4.2mm/s |
| Maximum Speed Full Load | 2.9mm/s |
| No Load Torque | N/A |
| Maximum Force Lifting | 6000N |
| Noise Level | ≤50dB |
| Motor | Permanent magnet motor 24V DC/ 2500rpm |
| Connection | Black PVC with molded F type 6 pin Din plug |
| Positioning Feedback | Hall effect sensor |
Mechanical Specifications
| Maximum Stroke Length | 100mm |
| Brake | N/A |
| Spindle Type | 8mm pitch |
| Gear Ratio | N/A |
| Front Connector | Drilled Hole, 10mm |
| Rear Connector | Drilled Hole, 10mm |
| Clevis Ends | Yes |
| Screw | ACME screw |
| Overall Length Closed | 320mm |
| Weight | 1.84Kg or 1840g |
| Ambient Operation Temperature | -20°C to 65°C |
| Storage Temperature | -20°C to 65°C |
| IP Rating | IP42 |
Approvals
| Compliance/Certifications | CE / EN55014-1:2017+A11:2020 |
| Declarations | EN 55014-2:2015 |
Accessories
| Accessory | RS PRO Product Number |
|---|---|
| Controller | 1774523 |
| Handset | 1774527 |
The controller accessory (RS PRO Product Number 1774523) is depicted as a black control box with buttons and a cable connected to a 6-pin DIN plug. The handset accessory (RS PRO Product Number 1774527) is shown as a black handheld remote control with a button.
Performance Charts and Dimensions
Speed vs. Load (24V DC): This chart illustrates the relationship between load and actuator speed. For both push/pull and push loads, the speed starts at approximately 40mm/s at 0N and decreases as the load increases, reaching around 2.9mm/s (push/pull) and 4.2mm/s (push) at 6000N.
Current vs. Load (24V DC): This chart shows the actuator's current consumption relative to the load. For both push/pull and push loads, the current starts at approximately 0.6A at 0N and increases with load, reaching around 2.7A at 6000N.
Dimensions: The actuator has an overall closed length of 320mm. Extended lengths are provided as A = 288mm and B = 388mm. Detailed diagrams illustrate the physical layout, including a motor housing diameter of Ø64mm and other component measurements.
Connector Specifications
Front Connector: Features a drilled hole with a diameter of 10mm (D1) and a slot width of 10mm (W). The material is Zinc Alloy.
Rear Connector: Similar to the front connector, with a drilled hole diameter of 10mm (D1) and a slot width of 10mm (W). The material is Zinc Alloy.
F type 6 Pin DIN Plug Pin Out: This connector is used for positioning feedback with dual Hall effect sensors. The pin assignments are: GND, Hall 2, M-, Vin, M+, Hall 1. A diagram shows the pin configuration of the F-type DIN male plug.
