JA-110A Internal Bus Siren
JABLOTRON
Product Overview
This document has been automatically translated from the original English version. In case of uncertainties or doubts, refer to the original document version. If you encounter errors or have further questions, contact technical support (contact details are at the end of this document).
The product is a component of the JABLOTRON system. It is used for alarm signaling within a building. Pressing a button on the siren allows silencing of the ongoing alarm signal (= confirmation of a person's presence in the building). The siren must be installed by a qualified technician with a valid certificate issued by an authorized distributor.
Installation
Always connect the bus when the system is completely powered off.
- Remove the siren body (buttons) from the plastic frame by pressing on one side of the body (1.) using a screwdriver as shown in Fig. 1.
- Remove the central part of the frame (3.) by pushing the 4 tabs indicated by the arrows (2.).
- Pass the bus cable through the dedicated rectangular cavity in the plastic base.
- Fix the plastic base at the chosen location using screws.
- Reassemble the plastic frame with the plastic base onto the lower part.
- Connect the bus cable to the terminals (6) as shown in Figure 2 and reinsert the body into the plastic frame.
Attention: the anti-tamper sensors (7) must be positioned over the magnets in the plastic base.
Diagrams
Fig. 1: Siren removal before installation.
Fig. 2: Description of the internal part of the siren.
Siren Internal Components:
- 1 - Electronic latches
- 2 - Internal buttons
- 3 - Serial number
- 4 - Body pin
- 5 - Piezoelectric siren
- 6 - Bus terminals
- 7 - Tamper sensor
System Enrollment and Settings
Depending on the control panel type, use the recommended software or application; consult the control panel manual.
Technical Specifications
| Feature | Specification |
|---|---|
| Power Supply | 12 V DC bus (9...15 V) |
| Standby Current Consumption | 5 mA |
| Maximum Current Consumption | 30 mA |
| Siren | Piezoelectric, 85 dB/m |
| Type of Warning Device | Internal, Type X |
| Dimensions | 80 x 80 x 28 mm |
| Acoustic Performance | 80 dB / 1 m |
| Classification | Security Grade 2 / Environmental Class II (according to EN 50131-1) |
| Environment | General indoor |
| Weight | 70 grams |
| Operating Temperature Range | -10 °C to +40 °C |
| Average Operating Humidity | 75% RH, non-condensing |
| Certification Body | Trezor Test s.r.o. (No. 3025) |
| Conforms to | EN 50131-1, -4, EN 50130-4, EN 55032, EN IEC 62368-1, EN IEC 63000 |
| Can be operated according to | ERC REC 70-03 |
| Recommended Screw | 2x Ø 3.5 x 40 mm (countersunk head) |
Compliance and Disposal
CE & UKCA Marking: JABLOTRON a.s. declares that the JA-110A device complies with the relevant European Union harmonization legislation: Directives No. 2014/30/EU, 2014/35/EU, 2011/65/EU, when used correctly. The original conformity assessment document is available on the website www.jablotron.com, in the Downloads section.
Disposal Notice: Proper disposal of this product will help save valuable resources and prevent potential negative effects on human health and the environment, which could otherwise result from inappropriate waste disposal. Return the product to the retailer or contact the local authority for more information on the nearest designated collection point.
For an electronic version of this manual (available in other languages) or the installer version for JA-100+, scan the enclosed QR code.
Contact Information
JABLOTRON a.s.
Pod Skalkou 4567/33
46601 Jablonec nad Nisou
Czech Republic
Tel.: +420 483 559 911
Internet: www.jablotron.com
