Cat Littler Box Assembly Instructions

Important Information & Safety

Important Information! Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.

Avoid Scratches! To avoid scratching, this furniture should be assembled on a soft layer, such as a rug.

Improve Efficiency! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

Anti-Topple Warning! Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.

Important Re-tightening Note: It is important that any product assembled using screws is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product.

Maintenance and Cleaning: For the frame, use a rag dipped in neutral detergent to wipe it, then dry with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, as the board is easy to break.

Tools Required

Please prepare the following tools:

• Screwdriver
• Phillips Head Screwdriver
• Razor/Blade
• Hex Key / Allen Wrench
• Drill

Note on Parts: When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.

Parts List

Note on Parts Diagram: The PDF includes an exploded view diagram showing all numbered parts (1-19) and their general shapes. This table lists the screw/hardware codes and their descriptions.

Assembly Steps

Step 1: Prepare Board 1

Insert two wooden dowels (A) into the corresponding holes on the edge of board 1. Align the two drawer runners (CL) with the pre-drilled holes on the side of board 1 and secure each with three screws (B). Then, flip board 1 to its back. Screw two eccentric rods (C) into the designated holes on board 1 using a screwdriver, ensuring they are fully seated.

Diagram shows dowels inserted into board 1, runners (CL) screwed onto the side, and eccentric rods (C) screwed into the back.

Step 2: Prepare Board 2

Insert two wooden dowels (A) into the designated holes on board 2. Screw two eccentric rods (C) into the corresponding holes on board 2 using a screwdriver.

Diagram shows dowels (A) and eccentric rods (C) being inserted into board 2.

Step 3: Connect Boards 1, 2, and 3

Position board 2 upright and align its dowels and eccentric rods with the corresponding holes on board 1. Attach board 1 to board 2. Then, align board 3 with the exposed ends of the eccentric rods from boards 1 and 2. Insert four cam locks (D) into the holes on board 3, aligning the arrow on the cam lock towards the eccentric rod. Turn each cam lock clockwise approximately 180 degrees with a screwdriver to secure the connection.

Diagram shows boards 1 and 2 being attached to board 3, with cam locks (D) inserted and tightened.

Step 4: Insert Back Board 4

Insert back board 4 along the available grooves as shown.

Diagram shows back board 4 sliding into grooves on the assembled structure.

Step 5: Assemble Middle Foot

Assemble the middle foot with foot pad (F) and metal plate (E) as shown. (x2)

Diagram shows a foot assembly: a cylindrical foot, a metal plate (E) at the bottom, and a foot pad (F) inserted into the top of the foot.

Step 6: Assemble Wooden Feet

Assemble the middle wooden feet with metal plates (E) as shown. (x4)

Diagram shows four cylindrical feet, each with a metal plate (E) at the bottom.

Step 7: Attach Legs to Board 7

Fix legs (5 and 6) to board 7 with screws (G) as shown. (x4 for each leg type)

Diagram shows board 7 (likely the base) with four leg assemblies (5 and 6) attached using screws (G).

Step 8: Connect Boards 7, 1, and 2

Connect board 7 to board 1 and 2, and fix with screws (H) as shown.

Diagram shows board 7 being attached to the main structure formed by boards 1 and 2, using screws (H).

Step 9: Prepare Board 8

Insert wooden dowels (A) into board 8. Fix runners (CR) to board 8 with screws (B) as shown.

Diagram shows dowels (A) inserted into board 8, and runners (CR) attached with screws (B).

Step 10: Prepare Board 9

Fix runners (CL) to board 9 with screws (B) as shown.

Diagram shows runners (CL) being attached to board 9 with screws (B).

Flip board 9 over. Insert wooden dowels (A) into board 9. Fix runners (CR) to board 9 with screws (B) as shown.

Diagram shows board 9 flipped, with dowels (A) inserted and runners (CR) attached with screws (B).

Step 11: Connect Boards 7, 8, and 9

Connect board 7 to board 8 and 9, and fix with screws (H) as shown.

Diagram shows board 7 being attached to the structure formed by boards 8 and 9, using screws (H).

Step 12: Insert Back Boards 4 and 10

Insert back boards 4 and 10 along available grooves as shown.

Diagram shows back boards 4 and 10 sliding into grooves on the assembled unit.

Step 13: Prepare Board 11

Screw eccentric rods (C) into board 11 with a screwdriver. Fix the door buffer (R) to board 11 as shown.

Diagram shows eccentric rods (C) and door buffer (R) being attached to board 11.

Step 14: Connect Board 11

Connect board 11 to the top. Add cam locks (D) into boards 1, 2, 8, and 9, then turn clockwise to tighten as shown.

Diagram shows board 11 being attached to the main structure, with cam locks (D) securing it to multiple connecting boards.

Step 15: Attach Buckles

Insert buckles (J) into back slots and fix with screws (K) as shown.

Diagram shows buckles (J) being inserted into slots on the back of the unit and secured with screws (K).

Step 16: Attach Hinges and Knobs to Door 12

Fix hinges (I) to door 12 with screws (S) as shown. Fix knob (M) to door 12 with screw (L) as shown.

Diagram shows hinges (I) and a knob (M) being attached to door 12.

Step 17: Attach Hinges and Knobs to Door 13

Fix hinges (I) to door 13 with screws (S) as shown. Fix knob (M) to door 13 with screw (L) as shown.

Diagram shows hinges (I) and a knob (M) being attached to door 13.

Step 18: Attach Doors to Unit

Assemble door 12 to board 2, and assemble door 13 to board 1, by fixing hinges with screws (S) as shown.

Diagram shows doors 12 and 13 being attached to the main unit via their hinges.

Step 19: Assemble Drawer Sides

Fix boards 14 and 16 to board 15 with screws (N) as shown. (x6)

Diagram shows drawer side panels (14, 16) being attached to drawer base/front panels (15) using screws (N).

Step 20: Insert Drawer Bottoms

Insert drawer bottom boards (17) along available grooves as shown. (x6)

Diagram shows drawer bottom panels (17) sliding into grooves on the partially assembled drawer boxes.

Step 21: Prepare Drawer Box 18

Screw eccentric rods (C) into board 18 with a screwdriver. Fix knob (M) to board 18 with screw (L) as shown. (x3)

Diagram shows eccentric rods (C) and knobs (M) being attached to drawer box component 18.

Step 22: Prepare Drawer Box 19

Screw eccentric rods (C) into board 19 with a screwdriver. Fix knob (M) to board 19 with screw (L) as shown. (x3)

Diagram shows eccentric rods (C) and knobs (M) being attached to drawer box component 19.

Step 23: Connect Drawer Box 18

Connect board 18 to the assembled component. Add cam locks (D) into boards 14 and 16, then turn clockwise to tighten as shown. (x3)

Diagram shows drawer box 18 being attached to the drawer slides on the main unit, secured with cam locks (D).

Step 24: Attach Drawer Runners to Drawer Boxes

Fix runners (DL) and (DR) to board 14 and 16 with screws (B) as shown. (x3)

Diagram shows drawer runners (DL, DR) being attached to the sides of the drawer boxes (14, 16) using screws (B).

Step 25: Connect Drawer Box 19

Connect board 19 to the assembled component. Add cam locks (D) into boards 14 and 16, then turn clockwise to tighten as shown. (x3)

Diagram shows drawer box 19 being attached to the drawer slides on the main unit, secured with cam locks (D).

Step 26: Attach Drawer Runners to Drawer Boxes

Fix runners (DL) and (DR) to board 14 and 16 with screws (B) as shown. (x3)

Diagram shows drawer runners (DL, DR) being attached to the sides of the drawer boxes (14, 16) using screws (B).

Step 27: Insert Drawers

Align rails and insert all drawers in.

Diagram shows the completed unit with drawers being slid into place.

Step 28: Install Anti-Topple Strap

A) Fix Anti-tipover strap (P) to the back side of board 11 with metal plate (T) and screw (G) as shown.

B) Select the location to place the Cabinet.

C) Mark location on the wall where the Safety Strap (P) will be anchored (position for Wall Anchor [Q]).

D) On the marked location, drill a hole in the wall that will fit (Q).

E) Fit (Q) into the drilled hole. Ensure that the wall anchor fits securely in the wall.

F) Use Screw (N) to affix the free end of Strap (P) and metal plate (T) to the wall anchor.

Diagrams show the anti-tipover strap (P) attached to the furniture and then secured to a wall anchor (Q) using screws (N) and plate (T).

Hinge Adjustment Video

If there is misalignment after you install, adjust the screw to the best condition. If doors are still not aligned correctly, please watch the video:

YouTube Hinge Adjustment Guide

Diagrams illustrate how to adjust furniture hinges for proper door alignment.

Warranty Information

Warranty Claims

• There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
• Before making a claim, please call to inquire. Provide your purchase order number and details of the problem. Replacement parts will be arranged within 48 hours. If out of stock, a shipping date will be provided.
• The product must be used in accordance with the instructions provided.
• For returns, the furniture must be cleaned and dried and returned within 30 days of receipt.

Type of Warranty Claim

• Failure to follow furniture instructions will invalidate the warranty.
• Damage during installation is not covered, but damage during transportation is.

Scope of Responsibility

• No responsibility will be borne for misuse, user damage, or loss of parts during installation.
• Damage and scratches after use are not covered by the warranty.

Warranty Coverage Areas (US)

• Sheet parts: 1 month from the date of purchase.
• Electrical parts: 1 month from the date of purchase.

Returns Policy

Changed Your Mind?

If you have purchased and simply changed your mind, follow the retailer's instructions for returns.

Defective Items

If your item is defective and you cannot identify why, please call first.

Damaged Items

If you receive an order with obvious shipping damage, refuse the delivery. If accepted and damage is found later, follow the retailer's specific instructions.

In all circumstances, save all packaging material and paperwork for the order. Disposing of packaging or attempting returns without contacting the fulfiller may jeopardize your claim and credit.

After-Sales Contact

Email: feedbackstation@163.com

Phone: (303)800-6387