Dsek Office Desk Assembly Instructions
Version: 12/19/2023
Important Information & Safety
IMPORTANT INFORMATION! Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.
AVOID SCRATCHES! In order to avoid scratching, this furniture should be assembled on a soft layer, such as a rug.
IMPROVE EFFICIENCY! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
ANTI-TOPPLE WARNING! ⚠️ Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.
IMPORTANT! It is important that any product which is assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months - in order to assure stability throughout the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.
Tools Required
Please prepare the following tools:
✏️ Pencil | ? Screwdriver (Phillips head) | ? Screwdriver (Flat head) | ? Screwdriver | ⚡ Power Drill (optional, use with caution)
Visual: Icons representing a pencil, a Phillips head screwdriver, a flat head screwdriver, a generic screwdriver, and a power drill.
Parts List
When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.
| Part | Quantity | Description | Dimensions |
|---|---|---|---|
| A | 44 | Eccentric Rod | Ø6 x 35 mm |
| B | 44 | Cam Lock | Ø15 x 10 mm |
| C | 18 | Wooden Dowel | Ø6 x 30 mm |
| D | 4 | Screw | Ø6 x 12 mm |
| E | 8 | Screw | Ø6 x 28 mm |
| F | 12 | Screw | Ø6 x 50 mm |
| G | 16 | Screw | Ø6 x 55 mm |
| H | 28 | Screw | Ø5 x 40 mm |
| I | 32 | Screw | Ø3.5 x 14 mm |
| J | 4 | Drawer Slide Hardware (J-1, J-2) | - |
| K | 4 | Foot Pad | - |
| L | 2 | Wire Box | - |
| M | 4 | Rod | 365 mm |
| N | 4 | Layer Pin | - |
| O | 1 | Allen Key | - |
Assembly Steps
Step 1: Attach Eccentric Rods to Board 6
Screw four eccentric rods (A) into the designated holes on board 6 using a screwdriver.
Visual: Diagram shows board 6. Close-up shows an eccentric rod (A) being screwed into a hole. An indicator shows the correct orientation and screw direction. Another diagram shows the board rotated 180 degrees, with rods inserted.
Step 2: Attach Boards 8 and 9 to Board 6
Attach boards 8 and 9 to board 6. Insert cam locks (B) into boards 8 and 9, and turn clockwise to tighten.
Visual: Board 6 is shown. Boards 8 and 9 are attached to its sides. Close-up shows a cam lock (B) being inserted into a hole on board 8/9 and turned 180 degrees to secure it to an eccentric rod from board 6.
Step 3: Attach Eccentric Rods to Board 5
Screw six eccentric rods (A) into the designated holes on board 5 as shown.
Visual: Diagram shows board 5 with six eccentric rods (A) being screwed into pre-drilled holes.
Step 4: Attach Board 5 to Boards 6, 9, and 8
Attach board 5 to boards 6, 9, and 8. Insert cam locks (B) into boards 6, 9, and 8, and turn clockwise to tighten.
Visual: Boards 6, 9, and 8 are assembled. Board 5 is being attached. Close-up shows cam locks (B) being inserted and turned 180 degrees to secure board 5.
Step 5: Attach Eccentric Rods to Board 2
Screw four eccentric rods (A) into the designated holes on board 2 as shown.
Visual: Diagram shows board 2 with four eccentric rods (A) being screwed into pre-drilled holes.
Step 6: Attach Boards 10 to Board 2
Attach boards 10 to board 2. Insert cam locks (B) into boards 10, and turn clockwise to tighten.
Visual: Board 2 is shown. Two boards labeled 10 are being attached to its sides. Close-up shows a cam lock (B) being inserted and turned 180 degrees.
Step 7: Attach Board 2 to Boards 6 and 5
Attach board 2 to board 6 and 5 using wooden dowels (C), and fix with screws (H) as shown.
Visual: Boards 5 and 6 are partially assembled. Board 2 is being attached between them. Wooden dowels (C) are inserted into holes, and screws (H) are used to secure the connection.
Step 8: Attach Eccentric Rods to Board 4
Screw eleven eccentric rods (A) into the designated holes on board 4 as shown.
Visual: Diagram shows board 4 with eleven eccentric rods (A) being screwed into pre-drilled holes.
Step 9: Assemble Main Frame
Insert wooden dowel (C) into board 2. Attach board 4 to boards 6, 9, 8, 2, and 10. Insert cam locks (B) into boards 6, 9, 8, 2, and 10, and turn clockwise to tighten.
Visual: A complex assembly of boards 2, 6, 9, 8, 10. Board 4 is being attached to this structure. Close-up shows dowel (C) insertion and cam lock (B) tightening.
Step 10: Attach Eccentric Rods to Board 3
Screw five eccentric rods (A) into the designated holes on board 3 as shown.
Visual: Diagram shows board 3 with five eccentric rods (A) being screwed into pre-drilled holes.
Step 11: Attach Board 3 to Boards 2 and 10
Insert wooden dowel (C) into board 2. Attach board 3 to board 2 and 10. Insert cam locks (B) into boards 2 and 10, and turn clockwise to tighten.
Visual: Boards 2 and 10 are shown. Board 3 is being attached. Close-up shows dowel (C) insertion and cam lock (B) tightening.
Step 12: Insert Layer Pins and Shelf
Insert layer pins (N) into boards 3 and 5. Then place shelf board 7 as shown.
Visual: Partially assembled unit. Layer pins (N) are inserted into holes on boards 3 and 5. Shelf board 7 is then placed onto these pins.
Step 13: Attach Eccentric Rods to Boards 12 and 13
Screw four eccentric rods (A) into boards 12 and 13 (two on each board) as shown.
Visual: Two boards labeled 12 and two boards labeled 13 are shown. Eccentric rods (A) are being screwed into them.
Step 14: Assemble Frame with Rods and Cam Locks
Insert rod (M) into boards 12 and 13. Connect board 15 to boards 12 and 13. Insert cam locks (B) into board 15 and turn clockwise to tighten.
Visual: Boards 12 and 13 are shown with rods (M) inserted. Board 15 is being attached. Close-up shows cam lock (B) tightening.
Step 15: Attach Boards 14 and 16 to Frame
Fix boards 14 and 16 to boards 12 and 13 with screws (H) as shown.
Visual: The frame assembled in step 14. Boards 14 and 16 are being attached to the sides using screws (H).
Step 16: Attach Board 11 to Main Structure
Attach board 11 to boards 12, 13, 14, 15, and 16 using wooden dowels (C) and fix with screws (H) as shown.
Visual: The main structure from step 15. Board 11 is being attached. Close-up shows dowel (C) insertion and screw (H) fastening.
Step 17: Attach Drawer Slide Hardware
Fix part (J) (drawer slide hardware J-1 and J-2) to board 11 with screws (I) as shown.
Visual: Board 11 is shown. Drawer slide components (J-1, J-2) are being attached to its surface using screws (I). Multiple instances are shown.
Step 18: Place Components onto Board 2
Place the two components (likely drawer units with slides attached) onto board 2 at first.
Visual: A partially assembled desk structure. Two vertical components, each labeled 11, are being lowered onto board 2.
Step 19: Attach Eccentric Rods to Board 1
Screw ten eccentric rods (A) into the designated holes on board 1 as shown.
Visual: Diagram shows board 1 with ten eccentric rods (A) being screwed into pre-drilled holes.
Step 20: Attach Top Board (Board 1)
Cover board 1 to the top using wooden dowels (C). Insert cam locks (B) into boards 3, 5, 6, and 4, and turn clockwise to tighten. Place wire boxes (L) into holes.
Visual: The main desk structure. Board 1 is being placed on top. Close-up shows dowel (C) insertion and cam lock (B) tightening. Wire boxes (L) are shown being placed into circular cutouts on board 1.
Step 21: Attach Tubes to Leg Parts
Fix tubes (20) to leg parts (21) with screws (G) as shown. Use Allen key (O) for tightening.
Visual: Two leg assemblies (21) and two tubes (20) are shown. Screws (G) are used to connect them. Close-up shows screw (G) and Allen key (O) in use.
Step 22: Attach Part 19 to Tubes
Fix part 19 to tubes (20) with screws (G) as shown. Use Allen key (O) for tightening.
Visual: The leg assembly from step 21. Part 19 is being attached to the tubes (20) using screws (G).
Step 23: Attach Leg Assembly to Board 18
Attach the leg assembly (from step 22) to board 18. Fix part 21 to board 18 with screw (E); tube 20 to board 18 with screw (F); part 19 to board 18 with screw (D) as shown. Rotate foot pads (K) into leg 21.
Visual: Board 18 is shown. The leg assembly is being attached. Screws (E, F, D) are used for connections. Foot pads (K) are screwed into the bottom of legs (21). Allen key (O) is shown for tightening.
Step 24: Attach Leg Assembly to Board 17
Attach the leg assembly (from step 22) to board 17. Fix part 21 to board 17 with screw (E); tube 20 to board 17 with screw (F); part 19 to board 17 with screw (D) as shown. Rotate foot pads (K) into leg 21.
Visual: Board 17 is shown. The leg assembly is being attached. Screws (E, F, D) are used for connections. Foot pads (K) are screwed into the bottom of legs (21). Allen key (O) is shown for tightening.
Step 25: Final Assembly and Wire Boxes
Fix the two components (likely the leg assemblies from steps 23 & 24) to board 1 with screws (E) as shown. Place wire boxes (L) into holes.
Visual: The main desk structure. The two leg assemblies are being attached to board 1. Wire boxes (L) are shown being placed into circular cutouts on board 1.
Warranty Information
WARRANTY CLAIMS
- There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase which must be verified by proof of purchase.
- Before making a claim, we may be able to answer your query, simply call us. Please leave your purchase order number, along with some details of the problem, if you want a replacement part. We will arrange within 48 hours. If there is out of stock, we will reply with a shipping date.
- The product must be used in accordance with the instructions provided. For health reasons.
- For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.
Type of Warranty Claim
- Failure to follow the furniture instructions will invalidate the warranty. Attention please.
- Does not include damage during installation, but includes damage during transportation.
Scope of responsibility
- Shall not bear any responsibility for misuse or user damage and / or loss of parts during the installation of furniture.
- After using, the damage and scratches of the furniture are not covered by the warranty.
The Warranty Relates to All Bought in The Us and Covers The Following Areas:
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
RETURNS
CHANGED YOUR MIND AND NEED TO RETURN YOU ITEM?
PLEASE FOLLOW THE BELOW INSTRUCTIONS:
- If you have purchased and have simply changed your mind, follow the retailer's instructions for returns.
DEFECTIVE ITEMS
- If your item is defective in any way, i.e. it doesn't work but you can't identify why, in the first instance, please call us.
DAMAGED ITEMS
- If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is refused. If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.
In all circumstances please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardise your chances of making a claim, and you may not receive a credit for the return.
AFTER-SALES CONTACT
✉️ feedbackstation@163.com
? (303)800-6387
