Fortin EVO-KEY Regular Installation Guide
Guide #: 66791 | Revision: 20250123
Addendum - Suggested Wiring Configuration
Vehicle Compatibility
Vehicle: KIA
Model: Niro
Type: Hybrid Push-to-start
Years: 2017-2021
Immobilizer Bypass: Supported
Firmware Update Tool
To add the firmware version and options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
Installation Description and Wiring Connections
This section details the physical connections required to install the Fortin EVO-KEY module into the Kia Niro. It involves identifying specific wires in the vehicle's harness and connecting them to the EVO-KEY module's outputs.
Connection Points
The installation requires accessing wiring harnesses at the following locations:
- Driver's Side Kick Panel: Contains an 82-pin black connector.
- Fuse Box (I/P): Includes a 4-pin black connector and a 38-pin white connector located at the back of the fuse box.
EVO-KEY Module and Vehicle Wire Mapping
The Fortin EVO-KEY module features several connectors. The following table summarizes the key connections between the module's outputs and the vehicle's identified wires:
| EVO-KEY Output/Wire | Vehicle Wire Color | Vehicle Wire Function | Connection Location/Connector |
|---|---|---|---|
| Data-Link Connector (4-pin) | N/A | Connects to module for programming | Module |
| B4 (RED) | Red | 12V Battery (+) | Fuse Box (I/P) - 4-pin Black Connector |
| B3 (BLACK) | Black | Ground (-) | Vehicle Ground Point |
| (+)START (Yellow) | Yellow | Starter Signal (+) | Fuse Box (I/P) - 38-pin White Connector |
| (+)12V (Red) | Red | 12V Constant (+) | Fuse Box (I/P) - 38-pin White Connector |
| (+)IGNITION1 (Pink) | Pink | Ignition 1 Signal (+) | Fuse Box (I/P) - 38-pin White Connector |
| (+)IGNITION2 (Green) | Green | Ignition 2 Signal (+) | Fuse Box (I/P) - 38-pin White Connector |
| (~)EMS COM (Brown/Orange) | Brown/Orange | EMS Communication Signal | Fuse Box (I/P) - 38-pin White Connector |
| (+)ACCESSORY (Blue) | Blue | Accessory Signal (+) | Fuse Box (I/P) - 38-pin White Connector |
| (+)BRAKE (Green) | Green | Brake Signal (+) | Driver's Side Kick Panel - 82-pin Black Connector |
| A1 (RS14) | (Specific wire not detailed in summary) | Ground Out While Running | (Specific location not detailed in summary) |
| A2 (RS8 OUT) | (Specific wire not detailed in summary) | Output Signal | (Specific location not detailed in summary) |
| A3 (RS7 OUT) | (Specific wire not detailed in summary) | Output Signal | (Specific location not detailed in summary) |
| A4 (RS6a OUT) | (Specific wire not detailed in summary) | Output Signal | (Specific location not detailed in summary) |
| A5 (RS6 IN/OUT) | (Specific wire not detailed in summary) | Input/Output Signal | (Specific location not detailed in summary) |
| A6 (RS5 OUT) | (Specific wire not detailed in summary) | Output Signal | (Specific location not detailed in summary) |
| D1 (WHITE/GREEN) | White/Green | (~)EMS COM | Driver's Side Kick Panel - 82-pin Black Connector |
| D2 (WHITE/BLUE) | White/Blue | (Function not detailed in summary) | Driver's Side Kick Panel - 82-pin Black Connector |
| D3 (WHITE/RED) | White/Red | (~)EMS COM | Driver's Side Kick Panel - 82-pin Black Connector |
Note: The specific pin numbers for each connection on the vehicle connectors are detailed in the original documentation. The table above provides a summary of wire colors, functions, and general connection locations.
Programming Procedure
- Step 1: Press and hold the programming button on the EVO-KEY module. Insert the 4-Pin Data-Link Connector. The LED indicator will alternate between YELLOW and RED.
- Step 2: Release the programming button when the LED turns solid RED. If the LED is not solid RED, disconnect the 4-Pin connector and repeat Step 1.
- Step 3: Insert the remaining required connectors into the EVO-KEY module.
- Step 4: Press and release the programming button 6 times (6x). The RED LED will flash 5 times and pause.
- Step 5: Do not press the brake pedal. Press the START/STOP button twice to turn ON the ignition. The RED LED will flash rapidly 10 times. This indicates the key bypass is programmed.
- Step 6: Press the START/STOP button once to turn OFF the ignition.
The module is now programmed. Test all supported features using the remote starter or security system to ensure proper programming.
Notices and Warnings
Firmware Updates
Updated firmware and installation guides are available on the Fortin website (www.fortinbypass.com). It is recommended to update the module to the latest firmware and download the latest installation guide before installation.
General Warning
The information provided is on an "as is" basis with no representation or warranty of accuracy. The installer is solely responsible for verifying all circuits before connection. Only a computer-safe logic probe or digital multimeter should be used. Fortin Electronic Systems assumes no liability for the accuracy or currency of the information or for any installation errors. The module must be installed by a qualified technician. This guide is for informational purposes and may change without notice. Visit www.fortinbypass.com for the latest version.
Technical Support
Phone: 514-255-HELP (4357) / 1-877-336-7797
Website: www.fortinbypass.com
Remote Car Starters, Car Alarms, Immobilizer Bypass and Connected Vehicle Solutions | Fortin Electronic Systems
Remote Car Starters, Car Alarms, Immobilizer Bypass and Connected Vehicle Solutions | Fortin Electronic Systems
