Fortin EVO-ONE Remote Starter Installation Guide

Introduction

This document provides installation and programming instructions for the Fortin EVO-ONE remote starter system, specifically for the THAR-ONE-TOY16 harness, designed for the 2025 Toyota Camry Hybrid with Push-to-Start ignition.

Module: EVO-ONE

Harness: THAR-ONE-TOY16

Vehicle: Toyota Camry Hybrid (2025) Push-to-Start

Guide Revision: 20250220

Vehicle Compatibility & Module Information

This module is compatible with Toyota Camry Hybrid vehicles manufactured after 2019.

The EVO-ONE module supports various vehicle functions, including:

• Immobilizer Bypass
• Lock/Unlock ?
• Arm/Disarm
• Horn
• Parking Light
• Tachometer
• Trunk Open
• Rear Defrost
• Heated Wiper
• Door Status
• Trunk Status
• Hand-Brake Status
• Foot-Brake Status
• Hood Status
• Secure Takeover
• OEM Remote Monitoring

Module Compatibility: Manufactured after 2019.

Firmware: To update firmware and options, use the Flash Link Updater or Flash Link Mobile tool (sold separately).

Unit Options

Configure the following bypass options:

Remote Starter Configuration for Comfort Group Activation:

Function: 39, Mode: 2

Description: Temperature option: AUX.1 activated at 5°C, 5 seconds after remote start.

Note: The vehicle's OEM remote and SmartKey remain operable during remote start.

Installation Locations

Key components are typically located:

• ECU: Behind the glove box.
• Connectors: Above the driver's kick panel.

Wiring Connections

This installation utilizes specialized T-Harnesses to integrate the EVO-ONE module with the vehicle's electrical system. Key connection points include:

• Main Harness (6-pin White Connector): Connects the EVO-ONE module to the vehicle's wiring.
• Vehicle Interface Connectors: Located above the driver's kick panel, these include a 54-pin Black connector, a 30-pin White connector, and a 30-pin Tan connector.
• T-Harness Connectors: Female connectors that mate with the vehicle's male connectors.

Important Wiring Notes:

• For Automatic Transmission Mode, cut the specified loop on the harness.
• [Hood Pin Switch]: Mandatory for safety. Ensure it is installed and configured via Option A11. If the vehicle lacks a functional hood pin, set A11 to OFF.

Refer to the original document's wiring diagrams for precise pin-to-pin connections.

Dcryptor Programming Procedure

Required Tools: Flash Link Updater or Flash Link Mobile, compatible computer (Windows) or smartphone (Android/iOS) with internet access.

Procedure:

1. Step 1: Press and hold the programming button on the EVO-ONE module. Connect the 6-pin Main harness (White connector). The LEDs will alternate between BLUE, RED, YELLOW, and BLUE/RED flashes.
2. Step 2: Release the programming button when the BLUE LED is solid ON. If the BLUE LED is not solid, disconnect and repeat Step 1.
3. Step 3: Insert the remaining required connectors.
4. Step 4: Ignition ON: Press the [Push-to-Start Button] twice to turn the ignition ON. The [BLUE LED] will flash rapidly.
5. Step 5: Ignition OFF: Press the [Push-to-Start Button] once to turn the ignition OFF. The [BLUE LED] will continue to flash rapidly.
6. Step 6: Unlock Vehicle: Press the Unlock button on the vehicle's OEM remote. The [BLUE LED] will turn ON solid.

Key Bypass Programming Procedure

Procedure:

1. Step 7: Press the foot-brake pedal. Press the [Push-to-Start Button] until the engine starts. Release the foot-brake pedal. The [BLUE LED] will turn OFF, and the [RED LED] will turn ON.
2. Step 8: Press the [Push-to-Start Button] once to turn off the engine.
3. Step 9: Press the foot-brake pedal. Press the [Push-to-Start Button] until the engine starts. Release the foot-brake pedal. The [RED LED] will turn OFF, and the [YELLOW LED] will turn ON. Wait for the RED and YELLOW LEDs to alternate.
4. Step 10: Press the [Push-to-Start Button] once to turn off the engine.
5. Step 11: Disconnect all connectors, including the 6-pin Main harness and the 4-pin Data-link connector.
6. Step 12: Use the Flash Link Updater or Flash Link Mobile tool to visit the DCryptor menu via your computer or smartphone.
7. Step 13: After completing the DCryptor programming, reconnect all vehicle connectors, starting with the 6-pin Main harness or 4-pin Data-link connector.

Verification: Test the remote starter by performing a remote start.

Remote Starter Functionality

To Start the Vehicle Remotely:

• Ensure all doors are closed.
• Press the Unlock button on your OEM remote, the remote-starter remote, or the proximity remote.
• Enter the vehicle with your Smart-Key.
• Important: Do NOT press the brake pedal.
• Press and release the [Push-to-Start Button] once.
• Now, press the brake pedal. The vehicle is ready to be put into gear and driven.

Note: If the Smart-Key is not detected, the vehicle will shut down.

Important Notices and Warnings

ℹ️ Firmware and Guide Updates: Fortin regularly updates firmware and installation guides. It is recommended to update to the latest firmware and download the most current installation guide from www.fortin.ca before installation.

⚠️ Installation Warning:

• This information is provided on an "as is" basis. The installer is solely responsible for verifying all circuits before connecting. Use only a computer-safe logic probe or digital multimeter.
• Fortin Electronic Systems assumes no liability or responsibility for the accuracy or currency of the information, or for any installation errors or damages resulting from improper installation.
• This module must be installed by a qualified technician. Incorrect connections can cause permanent damage to the vehicle.
• The information provided is a guide only and may change without notice.

Mandatory Safety Elements:

• The [Hood Pin Switch] (included) must be installed. If the vehicle can be remote started with the hood open, set Function A11 to OFF.
• The [Security Sticker] must be installed.

Technical Support:

• Phone: 514-255-HELP (4357) / 1-877-336-7797
• Website: www.fortinbypass.com