Vehicle Compatibility
This guide is for the Kia Niro Hybrid Push-to-start models from 2017-2021.
Product: Fortin EVO-KEY Interface Module
Function: Immobilizer Bypass
Note: The FLASH LINK UPDATER or FLASH LINK MOBILE tool is required for firmware updates and options, sold separately.
Connection Points Description
Fuse Box Locations
Location 1: In the front of the fuse box.
Location 2: Back of the fuse box.
Driver's Side Kick Panel
Location 3: In the driver's side kick panel.
Key Wires Identified:
- (+)12V
- (+)START
- (~)EMS COM
- (+)ACCESSORY
- (+)IGNITION2
- (+)IGNITION1
Wiring Connection Guide
This section details the wiring connections for the EVO-KEY module. Refer to the diagrams for specific pin assignments and wire colors.
Module Connections (EVO-KEY)
| Module Pin/Wire | Color | Function |
|---|---|---|
| (-)GWR | Dk. Blue | Out A1 |
| (+)IGNITION | Yellow | In A2 |
| (~)EMS COM | White/Black | Out A3 |
| (~)EMS COM | Red/Blue | In A4 |
| (~)EMS COM | Lt.Blue/Black | In/Out A5 |
| (~)EMS COM | Lt.Blue | In/Out A6 |
| (~) EMS COM | White/Green | D1 |
| (~) EMS COM | White/Blue | D2 |
| (~) EMS COM | White/Red | D3 |
Remote Starter Connections
| Remote Starter Output | Function |
|---|---|
| RS8 | BRAKE (+) |
| RS7 | STARTER (+) |
| RS6a | IGNITION2 (+) |
| RS6b | IGNITION1 (+) |
| RS5 | ACCESSORY (+) |
| RS2 | 12V BATTERY (+) |
| RS1 | Ground (-) |
Connector Pinouts
Detailed pinout diagrams are provided for the following connectors:
- White 38-Pins Connector (I/P Fuse box)
- Black 4-Pins Connector (I/P Fuse box)
- Black 82-Pin Connector (Driver's side kick panel)
Wire colors for connections include Yellow, Red, Pink, Green, Brown/Orange, and Blue.
Programming Procedure
Follow these steps to program the EVO-KEY module:
- Step 1: Press and hold the programming button. Insert the 4-Pin (Data-Link Connector). The LED will alternate between YELLOW and RED.
- Step 2: Release the programming button when the LED is RED. If the LED is not solid RED, disconnect the 4-Pin connector and return to Step 1.
- Step 3: Insert the remaining required connectors.
- Step 4: Press and release the programming button 6 times (6x). The RED LED will flash 5 times and pause.
- Step 5: (Ignition ON) Do not press the brake pedal. Press the START/STOP button twice to turn ON the ignition. The RED LED will flash rapidly 10x times. Key bypass is now programmed.
- Step 6: (Ignition OFF) Press the START/STOP button once to turn OFF the ignition.
Module Status: The module is now programmed. Test all supported features using the remote starter or security system remote.
Notices and Warnings
Firmware and Guide Updates
Updated firmware and installation guides are regularly posted on the Fortin website. It is recommended to update to the latest firmware and download the latest guide(s) before installation.
Visit: www.fortinbypass.com
General Warning
The information provided is on an "as is" basis without warranty. The installer is solely responsible for verifying circuits before connection. Only a computer-safe logic probe or digital multimeter should be used. Fortin Electronic Systems assumes no liability for accuracy or currency of information, or for installation outcomes. This module must be installed by a qualified technician. This guide is for suggestion only and may change without notice.
Technical Support
Phone: 514-255-HELP (4357) | 1-877-336-7797
Website: www.fortinbypass.com
Remote Car Starters, Car Alarms, Immobilizer Bypass and Connected Vehicle Solutions | Fortin Electronic Systems
Remote Car Starters, Car Alarms, Immobilizer Bypass and Connected Vehicle Solutions | Fortin Electronic Systems
