Fortin EVO-ONE Installation Guide Addendum

Vehicle Compatibility

This guide addendum is specifically for the following vehicle:

• Make: Toyota
• Model: RAV4
• Trim: Hybrid H-Key
• Years: 2019-2023

Product Overview

The Fortin EVO-ONE is a remote starter and bypass module designed to integrate with your vehicle's factory keyless entry system. This addendum provides specific wiring configurations and programming procedures for the THAR-ONE-TOY14 harness, intended for the Toyota RAV4 Hybrid.

The module supports various vehicle functions, including immobilizer bypass, remote start, and monitoring of OEM remote status.

[Diagram Description: A table lists supported vehicle functions: Immobilizer bypass, Lock, Unlock, Arm, Disarm, Parking Lights, Trunk (open), Tachometer, Autolight Off, Door Status, Trunk Status, Hand-Brake Status, Foot-Brake Status, Hood Status*, OEM remote Monitoring, R.S. OEM remote Stand Alone compatible.

Module Options and Features

The EVO-ONE module can be configured with specific options:

• Unit Option A11 (OFF/NON): Hood trigger (Output Status) / Contact de capot (état de sortie).
• Unit Option C1: OEM Remote status (Lock/Unlock) monitoring / Suivi des status de la télécommande d'origine.
• Unit Option D4: Hybrid mode (Vehicle hybrid only) / Mode hybride (véhicule hybride seulement).
• Unit Option D5: Lock after start / Verrouillage après le démarrage.

Firmware Version: Minimum 88.[15] required. Use Flash Link Updater or Flash Link Mobile tool (sold separately) to update firmware and options.

[Diagram Description: QR code labeled 'QR CODE LABELED' with text indicating 'COMPATIBLE MODULE REQUIRED: AFTER 2019' and 'FIRMWARE VERSION REQUIRED: 88.[15] MINIMUM'. Also mentions using 'FLASH LINK UPDATER' or 'FLASH LINK MOBILE' tools.

Remote Starter Options

The module supports remote starter functions:

• Function 32, Mode 3: DK.Blue (GWR) Shut Down After / Bleu Foncé (Masse d'activation) Sortie après l'arrêt.
• Function 38, Mode 2 (Enable): Press 3x Lock to remote start with the OEM remote. / Activé: Appuyez x3 sur Verrouille de la télécommande d'origine pour démarrer à distance le véhicule.

Mandatory Installation Components

The following components are mandatory for installation:

• Hood Pin Switch: Must be installed if the vehicle can be remote started with the hood open. Set Function A11 to OFF if the hood pin is installed.
• Security Sticker: Essential security element that must be installed.

Installation Wiring Overview

This section details the connection points within the vehicle.

[Diagram Description: Image showing the steering column area with connection points labeled (+ ACCESSORY, + STARTER, + IGNITION, + 12V).]

[Diagram Description: Image showing the junction connector on the left side of the ECU. Labeled wires include (-) CAN LOW, (-) DRIVER DOOR PIN, (-) CAN HIGH, (-) IMO, (-) IMI, (-) DOORLOCKS DATA.]

[Diagram Description: Image showing the passenger kick panel junction connector. Includes a connection for TPMS and a note stating: "CONNECTION ONLY REQUIRED IF REMOTE START CONTROL FROM OEM REMOTES IS DESIRED AND VEHICLE IS EQUIPPED WITH TIRE PRESSURE MONITORING SYSTEM (TPMS)."]

Detailed Wiring Connections (THAR-ONE-TOY14)

The following describes the connections for the THAR-ONE-TOY14 harness. Refer to the diagrams for precise pin locations and wire colors.

[Diagram Description: A comprehensive wiring diagram illustrates the connections between the EVO-ONE module (labeled A-J) and various vehicle harness connectors (e.g., E5 (+ IGNITION), E3 (+ 12V), E2 (+ ACCESSORY), E6 (+ STARTER), A20 (DOOR LOCKS DATA), C3 (CAN HIGH), C4 (CAN LOW), A8 (DRIVER DOOR PIN), A16 (IMO), D1 (IMI), D4 (TPMS). Wire colors and pin assignments are detailed. A note indicates to 'CUT LOOP FOR AUTOMATIC TRANSMISSION MODE'. Views of vehicle connectors (8-pin ignition, 21-pin ECU, 30-pin ECU, 20-pin ECU, 20-pin passenger kick panel) are shown.]

[Diagram Description: Specific wiring for THAR-ONE-TOY14 and THAR-TY81 harnesses, including Option A, B, and C T-harness connections. Instructions are provided to connect Yellow/Red and Yellow/Green wires together for Option A. Shows connections at the Ignition Switch, ECU, and Passenger kick panel.]

Note on TPMS: The TPMS connection (D4, D6) is only required if remote start control from OEM remotes is desired and the vehicle is equipped with a Tire Pressure Monitoring System.

Programming Procedures

Follow these procedures to program the module.

Dcryptor Programming Procedure

1. Parts Required: Flash Link Updater, Flash Link Manager software, or Flash Link Mobile app. A Microsoft Windows computer or smartphone with internet connection is needed.
2. Preparation: Before programming, set the unit options and save them using the appropriate tool.
3. Step 1: Press and hold the programming button on the module. Connect the 6-PIN Main harness (white connector). The LEDs will alternate between Blue, Red, Yellow, and Blue/Red flashes.
4. Step 2: Release the programming button when the LED turns solid Blue. If the Blue LED is not solid, disconnect and restart from Step 1.
5. Step 3: Insert the remaining required connectors.
6. Step 4: Turn the vehicle key to the Ignition ON/RUN position. The Blue LED will flash rapidly.
7. Step 5: Wait. The Blue LED will turn solid ON.
8. Step 6: Start the vehicle. The Blue LED will turn OFF, and the Red LED will turn ON.

Key Bypass Programming Procedure

1. Step 6: Turn the vehicle key to the OFF position.
2. Step 7: Remove the key from the ignition switch.
3. Step 8: Start the vehicle. The Red LED will turn OFF, and the Yellow LED will turn ON. Wait for the Red and Yellow LEDs to alternate.
4. Step 9: Turn the vehicle key to the OFF position.
5. Step 10: Disconnect all connectors, including the 6-Pin Main harness or the 4-Pin Data-link connector.
6. Step 11: Use the Flash Link Updater or Flash Link Mobile tool to visit the DCryptor menu.
7. Completion: After programming, reconnect the 6-Pin (Main-Harness) or 4-pin (Data-Link) connector, followed by all other remaining connectors.

Remote Starter Functionality Verification

Test the remote starter by initiating a remote start sequence.

[Diagram Description: Illustrated steps for remote starter functionality: 1. All doors must be closed. 2. Remote start the vehicle. 3. Unlock the doors with the remote-starter remote or the OEM remote. 4. Insert and turn the key to the Ignition ON/RUN position. 5. Press the brake pedal. 6. The vehicle is now ready to be put into gear and driven.]

Note: Refer to the Quick Install Guide included with the module for detailed remote starter programming.

Important Warnings and Notices

Fortin Electronic Systems assumes no liability for the accuracy or currency of the information supplied. Installation is the sole responsibility of the installer.

Support Information

For technical support, contact:

• Phone: 514-255-HELP (4357) or 1-877-336-7797
• Website: www.fortinbypass.com

Visit the website for web updates and the latest version of the guide.