JA-110P PET - PIR Motion Detector for Bus with Basic Animal Immunity
This document has been automatically translated from the original English. In case of uncertainties or doubts, please refer to the original document version. If you encounter errors or have other questions, please contact Technical Support (contact details are at the end of this document).
Product Overview
The JA-110P PET is a bus device of the JABLOTRON system. It detects human movement inside buildings. Unlike standard JABLOTRON series PIR motion detectors, this detector features modified detection characteristics and is equipped with basic animal immunity. It eliminates the effects of small animals moving on the floor (animals weighing up to approximately 25 kg and measuring up to 40 cm). The detector is impulse-reactive and occupies a unique position in the system. Installation must be performed by a qualified technician, holding a valid certificate issued by an authorized distributor.
Installation
⚠️ When connecting the detector to the bus, always disconnect the system power.
- Open the detector cover by pressing the latch (5). Avoid touching the PIR sensor (11) inside, as you might damage it.
- Remove the PCB – it is held by a latch (3).
- Drill holes for screws and the cable in the plastic base. The recommended installation height for the detector is 2 m above the floor.
- Insert the bus cable and fix the plastic base to the wall with screws (vertically, with the cover latch facing downwards).
- Reinsert the PCB and connect the cables to the terminals (8).
- Proceed according to the control panel installation manual.
Diagram Description
Fig. 1: Detector opening and description of internal and external product parts.
Internal and External Parts:
- 1 – Holes for flat wall installation
- 2 – Holes for corner installation
- 3 – Printed circuit board latch
- 4 – Holes for corner installation
- 5 – Cover latch
PCB Terminals and Indicators:
- 6 – Red LED – activation
- 7 – Yellow LED – fault
- 8 – Bus terminals
- 9 – Production code
- 10 – Cover tamper sensor
- 11 – PIR sensor
The diagram illustrates the detector's physical layout. View I shows the front with mounting points. View II shows the rear with the main circuit board (PCB) and its connections. The PCB features terminals labeled +U, A, B, and GND, along with indicator LEDs and sensors.
System Assignment and Parameters
Depending on the control panel type, use the recommended software or application; refer to the control panel manual.
Technical Specifications
| Power | 12 V (8...15 V) from the control panel bus |
| Quiescent current consumption | 5 mA |
| Maximum current consumption | 10 mA |
| Recommended installation height | 2 m above the floor |
| Detection angle / detection coverage | 90° / 12 m |
| Detection angle / detection coverage (animal immunity) | 90° / 7 m |
| Dimensions | 60 x 98 x 52 mm |
| Weight | 75 g |
| Classification | Class 2/II. General indoor (according to EN 50131-1) |
| Operating environment | General indoor |
| Operating temperature range | -10 °C to +40 °C |
| Average operating humidity | 75% RH, non-condensing |
| Certification body | Trezor Test sro (No. 3025), KIWA Nederland bv |
| Also complies with | EN 50131-1, EN 50131-2-2, EN 50130-4, EN 55032, EN CEI 63000, T 031. |
| Recommended screws | 2x Ø 3.5 x 40 mm (countersunk head) |
Conformity Declaration
JABLOTRON a.s. hereby declares that the PET JA-110P complies with the European Union harmonization legislation: Directives No. 2014/30/EU and 2011/65/EU, when used as intended. The original Declaration of Conformity is available at www.jablotron.com, Downloads section.
[CE Mark] [CA Mark]
Disposal and Further Information
Disposal Note: Proper disposal of this product will help preserve valuable resources and prevent potential negative effects on human health and the environment, which could result from improper waste management. Please return the product to the retailer or contact your municipality to find the nearest collection point.
To obtain an electronic version of this document (available in other languages) or an installation version in JA-100 format, scan the QR code provided.
