INSTALLATION Product Manual
Version: 210251-00-24A-LJ
Important Information and Assembly Guidelines
IMPORTANT INFORMATION! Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference. ❓
AVOID SCRATCHES! In order to avoid scratching, this furniture should be assembled on a soft layer, such as a rug. ❗
IMPROVE EFFICIENCY! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time. ????
ANTI-TOPPLE WARNING! Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the tipover restraint provided with this product. If not included, please purchase a wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully. ⚠️
IMPORTANT! It is important that any product assembled using screws is re-tightened 2 weeks after assembly, and once every 3 months, to ensure stability throughout the product's lifespan. For regular maintenance and cleaning of the frame, use a rag dipped in neutral detergent, wipe thoroughly, and then dry with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use excessive force when installing, as the board is easy to break. ❗
Tools and Parts Required
Please prepare the following tools and parts:
- Screws:
- A x 76 (CRA0635A)
- B x 76 (CRB1595A)
- C x 8 (CRF0630A)
- D x 48 (CRC0540A)
- E x 98 (CRD3512A)
- F x 8 (CRD3520A)
- G x 2 (CRD3535A)
- H x 2
- I x 2
When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size. ?
Also note the following components:
- 17: 14" (3508) - 12 SETS (likely refers to drawer slides)
Assembly Steps
Step 1: Separating Drawer Slides
Slides must be separated before assembly. After separation, set aside until needed.
Diagram shows the process of separating a drawer slide. It involves extending the slide (Step 1), pushing a lever upwards (Step 2), and then removing the runner component (Step 3).
- STEP 1: Extend Slide.
- STEP 2: Push Lever UP.
- STEP 3: Remove Runner.
Step 1 (Part 2 Attachment)
Insert quickfit screw(A) into part 2. Fix slide rail 17 to part 2 using screw(E) as shown.
Diagram illustrates attaching slide rail 17 to part 2 using screws A and E. It highlights the specific holes for insertion and advises against using an electric screwdriver.
Step 2 (Part 3 Attachment)
Insert quickfit screw(A) into part 3. Fix slide rail 17 to part 3 using screw(E) as shown.
Diagram illustrates attaching slide rail 17 to part 3 using screws A and E. It emphasizes paying attention to the insertion holes and avoiding electric screwdrivers.
Step 3 (Part 4 Left Attachment)
Fix slide rail 17 to the left of part 4 using screw(E) as shown.
Diagram shows slide rail 17 being attached to the left side of part 4 using screw E.
Step 4 (Part 4 Right Attachment)
Fix slide rail 17 to the right of part 4 using screw(E) as shown.
Please note, the pre-drilling of the rail on the front and back of this board is asymmetrical. Please install the rails according to the picture. This side as shown must be facing the middle drawer after installation is complete.
Diagram shows slide rail 17 being attached to the right side of part 4 using screw E. It highlights the asymmetrical pre-drilling and the correct orientation for the middle drawer.
Step 5 (Part 5 Left Attachment)
Fix slide rail 17 to the left of part 5 using screw(E) as shown.
Please note, the pre-drilling of the rail on the front and back of this board is asymmetrical. Please install the rails according to the picture. This side as shown must be facing the middle drawer after installation is complete.
Diagram shows slide rail 17 being attached to the left side of part 5 using screw E. It emphasizes the asymmetrical pre-drilling and correct orientation.
Step 6 (Part 5 Right Attachment)
Fix slide rail 17 to the right of part 5 using screw(E) as shown.
Diagram shows slide rail 17 being attached to the right side of part 5 using screw E.
Step 7 (Part 7 Attachment)
Insert quickfit screw(A) to part 7 as shown.
Diagram shows screws A being inserted into part 7.
Step 8 (Part 6 Attachment)
Insert quickfit screw(A) to part 6 as shown (x3).
Diagram shows screws A being inserted into part 6, repeated three times.
Step 9 (Part 18 Attachment)
Insert quickfit screw(A) to part 18 as shown.
Diagram shows screws A being inserted into part 18.
Step 10 (Frame Assembly)
Attach part 6 and 18 to part 4 and 5, turn cam locks(B) clockwise to tighten as shown. Attach part 7 to part 4 and 5, turn cam locks(B) clockwise to tighten as shown.
Diagram shows the assembly of the main frame. Parts 6, 18, and 7 are attached to parts 4 and 5 using cam locks (B) which are turned clockwise.
Step 11 (Side Panel Attachment)
Attach part 2, 3 to part 6, 18 and 7, turn cam locks(B) clockwise to tighten as shown.
Diagram shows side panels (parts 2 and 3) being attached to the assembled frame (parts 6, 18, 7) using cam locks (B) turned clockwise.
Step 12 (Top/Back Panel Attachment)
Connect part 8, 22 with part 9 and insert into the available slots of part 2, 3 and 7 as shown.
Diagram shows connecting parts 8 and 22 to part 9, and then inserting this assembly into the slots of the main unit (parts 2, 3, 7).
Step 13 (Top Panel Preparation)
Insert quickfit screw(A) to part 1 as shown. Fix part(I) to part 1 using screw(E) as shown.
Please pay attention to the holes where the accessories are inserted and don't use an electric screwdriver.
Diagram shows screws A being inserted into part 1, and then part I being attached to part 1 using screws E.
Step 14 (Top Panel Installation)
Cover part 1 to the assembled unit with wooden dowel(C), and turn cam locks(B) clockwise to tighten as shown.
Diagram shows the prepared top panel (part 1) being placed onto the assembled unit, secured with wooden dowels (C) and cam locks (B) turned clockwise.
Step 15 (Back Panel Installation)
Fix back panel 22 and 8 to the assembled unit with screw(F) as shown.
Diagram shows back panels (parts 22 and 8) being attached to the rear of the assembled unit using screws (F).
Step 16 (Anti-Dumping Installation)
Install anti-dumping hardware as shown in the figure.
Diagram illustrates the installation of anti-dumping straps or brackets. It shows screws (G, I) being used to attach a bracket to the furniture, and then a strap (H) connecting it to the wall.
Note: This step is crucial for safety and involves securing the furniture to the wall.
Step 17 (Drawer Part 10 Preparation)
Insert quickfit screw(A) to part 10 as shown (x3).
Diagram shows screws A being inserted into part 10, repeated three times.
Step 18 (Drawer Part 11 Preparation)
Insert quickfit screw(A) to part 11 as shown (x3).
Diagram shows screws A being inserted into part 11, repeated three times.
Step 19 (Drawer Part 12 Preparation)
Insert quickfit screw(A) to part 12 as shown (x3).
Diagram shows screws A being inserted into part 12, repeated three times.
Step 20 (Drawer Part 19 Preparation)
Insert quickfit screw(A) to part 19 as shown.
Diagram shows screws A being inserted into part 19.
Step 21 (Drawer Part 20 Preparation)
Insert quickfit screw(A) to part 20 as shown.
Diagram shows screws A being inserted into part 20.
Step 22 (Drawer Part 21 Preparation)
Insert quickfit screw(A) to part 21 as shown.
Diagram shows screws A being inserted into part 21.
Step 23 (Drawer Side Assembly)
Connect part 13 and 14 to part 15 using screw(D) as shown (x12).
Diagram shows parts 13 and 14 being connected to part 15 using screws D, repeated twelve times. This likely forms the sides of the drawers.
Step 24 (Drawer Bottom/Back)
Insert part 16 into the available slots as shown (x12).
Diagram shows part 16 being inserted into the slots of the drawer assembly, repeated twelve times. This likely forms the drawer bottom or back panel.
Step 25 (Drawer 10 Assembly)
Attach part 10 to part 13 and 14, turn cam locks(B) clockwise to tighten as shown (x3).
Diagram shows part 10 being attached to the drawer sides (parts 13 and 14) using cam locks B, repeated three times.
Step 26 (Drawer 11 Assembly)
Attach part 11 to part 13 and 14, turn cam locks(B) clockwise to tighten as shown (x3).
Diagram shows part 11 being attached to the drawer sides (parts 13 and 14) using cam locks B, repeated three times.
Step 27 (Drawer 12 Assembly)
Attach part 12 to part 13 and 14, turn cam locks(B) clockwise to tighten as shown (x3).
Diagram shows part 12 being attached to the drawer sides (parts 13 and 14) using cam locks B, repeated three times.
Step 28 (Drawer 19 Assembly)
Attach part 19 to part 13 and 14, turn cam locks(B) clockwise to tighten as shown.
Diagram shows part 19 being attached to the drawer sides (parts 13 and 14) using cam locks B.
Step 29 (Drawer 20 Assembly)
Attach part 20 to part 13 and 14, turn cam locks(B) clockwise to tighten as shown.
Diagram shows part 20 being attached to the drawer sides (parts 13 and 14) using cam locks B.
Step 30 (Drawer 21 Assembly)
Attach part 21 to part 13 and 14, turn cam locks(B) clockwise to tighten as shown.
Diagram shows part 21 being attached to the drawer sides (parts 13 and 14) using cam locks B.
Step 31 (Drawer Slide Attachment - Drawer 10)
Fix slide rail 17 to part 13 and 14 using screw(E) as shown (x3).
Diagram shows slide rail 17 being attached to the drawer sides (parts 13 and 14) using screws E, repeated three times for drawer 10.
Step 32 (Drawer Slide Attachment - Drawer 11)
Fix slide rail 17 to part 13 and 14 using screw(E) as shown (x3).
Diagram shows slide rail 17 being attached to the drawer sides (parts 13 and 14) using screws E, repeated three times for drawer 11.
Step 33 (Drawer Slide Attachment - Drawer 12)
Fix slide rail 17 to part 13 and 14 using screw(E) as shown (x3).
Diagram shows slide rail 17 being attached to the drawer sides (parts 13 and 14) using screws E, repeated three times for drawer 12.
Step 34 (Drawer Slide Attachment - Drawer 19)
Fix slide rail 17 to part 13 and 14 using screw(E) as shown.
Diagram shows slide rail 17 being attached to the drawer sides (parts 13 and 14) using screws E for drawer 19.
Step 35 (Drawer Slide Attachment - Drawer 20)
Fix slide rail 17 to part 13 and 14 using screw(E) as shown.
Diagram shows slide rail 17 being attached to the drawer sides (parts 13 and 14) using screws E for drawer 20.
Step 36 (Drawer Slide Attachment - Drawer 21)
Fix slide rail 17 to part 13 and 14 using screw(E) as shown.
Diagram shows slide rail 17 being attached to the drawer sides (parts 13 and 14) using screws E for drawer 21.
Step 37 (Drawer Insertion)
Align the rails, put all drawers as shown.
Note: Part 10, 19 drawers are put in the left; part 11, 20 in the middle; part 12, 21 in the right.
Diagram shows the completed dresser with all drawers inserted into their respective positions, indicating the correct placement for each drawer type (left, middle, right).
Warranty Information
WARRANTY CLAIMS
- There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
- Before making a claim, please call us. Please leave your purchase order number and details of the problem. Replacement parts will be arranged within 48 hours. If out of stock, a shipping date will be provided.
- The product must be used in accordance with the provided instructions.
- For other reasons, if the furniture needs to be returned, it must be cleaned and dried and returned within 30 days of receipt.
Type of Warranty Claim
- Failure to follow the furniture instructions will invalidate the warranty.
- Does not include damage during installation, but includes damage during transportation.
Scope of Responsibility
- No responsibility will be borne for misuse, user damage, or loss of parts during installation.
- Damage and scratches after use are not covered by the warranty.
The Warranty Relates to All Bought in The US and Covers The Following Areas
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
Returns
CHANGED YOUR MIND AND NEED TO RETURN YOUR ITEM?
PLEASE FOLLOW THE BELOW INSTRUCTIONS:
- If you have purchased and simply changed your mind, follow the retailer's instructions for returns.
DEFECTIVE ITEMS
- If your item is defective in any way, i.e., it doesn't work but you can't identify why, please call us in the first instance.
DAMAGED ITEMS
- If you receive an order with obvious shipping damage from the retailer, we suggest refusing the delivery. If delivery has been accepted and shipping damage is found, please follow the specific instructions advised by the retailer.
- In all circumstances, please save all packaging material and paperwork for the order. Be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardize your chances of making a claim and may not receive credit for the return.
AFTER-SALES CONTACT
? feedbackstation@163.com
? (303)800-6387
