BRIMNES Chest of 4 Drawers

Step 1: Attach Drawer Runners to Side Panels

Lay the two main side panels flat. Attach the drawer runners to the inside surfaces of these panels using screws (100365). Ensure correct orientation as per the diagram.

Step 2: Assemble Base Structure

Connect the base panels together. Insert cam lock screws (118331/112996) into the designated holes and secure them with cam locks (103058).

Step 3: Attach Side Panels to Base

Attach the side panels (prepared in Step 1) to the assembled base structure. Use cam lock screws and cam locks to secure them firmly.

Step 4: Attach Bracket to Side Panel

Fasten an L-bracket (106989) to the upper rear section of one of the side panels using screws (100823) and washers (100823).

Step 5: Insert Dowels into Vertical Panel

Insert wooden dowels (101345) into the pre-drilled holes on the edge of a vertical panel.

Step 6: Attach Horizontal Panel

Connect a horizontal panel to the vertical panel from Step 5. Align the panel with the inserted dowels and secure it using screws (105248).

Step 7: Insert Dowels into Second Vertical Panel

Insert wooden dowels (101345) into the pre-drilled holes on the edge of another vertical panel.

Step 8: Attach Shelves

Position the shelves between the side panels. Secure them using cam lock screws (100365) and cam locks (105248/155669).

Step 9: Slide in Back Panels

Carefully slide the thin back panels into the grooves located on the rear edges of the assembled side and base panels.

Step 10: Secure Back Panels

Fasten the back panels in place using screws (118224/119030) along the edges.

Step 11: Place Top Panel

Position the top panel onto the assembled unit. Ensure it aligns correctly with any dowels or connecting points.

Step 12: Secure Top Panel

Firmly attach the top panel to the main structure using screws (118224/119030).

Step 13: Attach Anti-Tip Bracket to Unit

Attach one part of the anti-tip device (L-bracket 106989) to the top rear edge of the unit. Use screws (155669) and cam locks (105248) for this connection.

Step 14: Secure Anti-Tip Device to Wall

This is a critical step for safety. Mark the wall at the desired height. Drill holes appropriate for your wall type (e.g., drywall, concrete, wood). Insert wall anchors if necessary. Secure the other part of the anti-tip device (e.g., strap or bracket) to the wall using appropriate screws. Refer to Step 22 for detailed wall anchoring instructions.

Step 15: Attach Remaining Drawer Runners

Attach the remaining drawer runners to the inside of the unit's side panels, aligning them with the pre-drilled holes, using screws (105248).

Step 16: Assemble Drawers - Sides and Fronts

Take the drawer front panels and drawer side panels. Connect the sides to the front using cam lock screws (118331/112996) and cam locks (103058).

Step 17: Insert Drawer Bottoms

Slide the drawer bottom panels into the grooves provided on the inside of the assembled drawer sides.

Step 18: Attach Drawer Backs

Attach the drawer back panels to the drawer sides, ensuring the drawer bottom panel is correctly seated in its groove. Secure with screws.

Step 19: Insert Drawers into Unit

Carefully slide the assembled drawers into the unit, aligning the drawer runners with the runners attached to the unit.

Step 20: Attach Drawer Handles

Attach the drawer handles to the front of each drawer using the provided screws (153548/158568).

Step 21: Final Unit Check and Wall Anchoring

Ensure all parts are securely fastened. Verify that the anti-tip device is correctly installed and firmly attached to both the unit and the wall. This is crucial for stability and safety.

Step 22: Detailed Wall Anchoring Options

This step illustrates different methods for securing the anti-tip device to various wall types:

• For solid walls (e.g., concrete, brick): Drill holes using an Ø 8 mm drill bit. Insert appropriate wall plugs (not explicitly shown but implied) and secure the bracket with screws.
• For hollow walls (e.g., drywall): Drill holes using an Ø 8 mm drill bit. Use appropriate drywall anchors (not explicitly shown but implied) and secure the bracket with screws.
• General guidance: The diagrams show drilling, inserting anchors, and screwing. Ensure the wall material can support the weight.

The IKEA website www.ikea.com/secure-it provides further information on preventing furniture tip-over.

Step 23: Adjust Drawer Runners

Make any necessary adjustments to the drawer runners to ensure drawers open and close smoothly.

Step 24: Final Drawer Insertion

Insert the completed drawers into the unit.

Step 25: Final Safety Reminder

Confirm that the anti-tip device is correctly installed. Ensure drawers are not overloaded and only one drawer is opened at a time.