OttLite Craft Organizer Lamp with 3x Dual Magnifier & 360° Rotating Tray

Product Overview

Congratulations on purchasing the OttLite Craft Organizer Lamp, designed with natural lighting technology. This lamp features a 3x dual magnifier and a 360° rotating tray, making it ideal for crafting and detailed work.

Lamp Components

The following components are referenced in the assembly instructions:

• A: Base
• B: Lamp Body
• C: Bulb (Tube)
• D: Magnifier
• E: Shade
• F: Tension Nut (for socket joint)
• G: Support Arms (for shade and magnifier)
• H: Rocker Switch
• J: Thumbscrew (for lamp body joint)
• M: Lamp Body Joint
• O: Socket Joint
• P: Flat Washer
• Q: Screw
• R: Knobs (for magnifier support arm)

Important Safety Instructions

WARNING: To prevent electric shock, ensure the lamp is not plugged in until all assembly steps are complete.

Polarized Plug: This portable lamp has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord unless the plug can be fully inserted. Do not alter the plug.

Electric Shock Prevention: To prevent electric shock, match the wide blade of the plug to the wide slot and insert fully.

Damaged Cord: If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.

FCC Compliance: This product complies with Part 18 of FCC Rules. However, it may cause interference to radios, televisions, wireless telephones, and remote controls. Avoid placing this product near these devices. If interference occurs, move the product away from the device or plug it into a different outlet. Do not install this product near maritime safety equipment or other critical navigation or communication equipment operating between 0.45-30 MHz.

Lamp Assembly

1. Remove the lamp from packing and place the base (A) on a steady surface.
2. To install the lamp body (B) into the base (A), turn the assembly upside down. Install the flat washer (P) and screw (Q) into the lamp dowel through the base. Turn clockwise with a screwdriver until snug. (Screwdriver not included). Set the assembly rightside up on a firm surface.
3. To install the shade (E), align the notch of the shade with the tab of the socket housing, then push it back into the socket assembly, ensuring the shade "snaps" into place.
4. Refer to the "Bulb Installation and Removal" section to install bulb (C) into the lamp. Also, refer to this section for removal and replacement of shade (E).
5. Plug the cord into a standard 120Vac outlet.
6. To turn the lamp on or off, depress the rocker switch (H) located in the cord-mounted power box.
7. To adjust the position of the shade (E), grasp the shade with one hand while holding the support arms (G). The shade (E) can rotate around the socket or move up and down at the socket joint (O). Note: Do not try to move the shade (E) beyond the limits of socket joint (O) as lamp damage may occur.
8. To raise or lower the magnifier (D), grasp the support arms (G) and gently move them up or down.
9. To rotate the magnifier (D), grasp the support arms (G) with one hand and move the magnifier (D) into position. The magnifier can also be rotated horizontally.
10. The lamp body joint (M) may be tightened by turning the thumbscrew (J) clockwise. To prevent damaging the lamp, do not use a tool and do not apply excessive force.
11. The socket joint (O) may be tightened by turning the thumbscrew (F) clockwise. To prevent damaging the lamp, do not use a tool and do not apply excessive force.

Note on Magnifier Support Arm: If the magnifier support arm (G) becomes loose, use a coin to tighten the two knobs (R) located near the bottom of the support arm. To prevent damaging the lamp, do not overtighten the screws or apply excessive force.

Bulb Installation and Removal

1. Make sure that the lamp is not plugged into an electrical outlet.
2. If the lamp has been in use, allow it to cool for approximately five minutes before proceeding.
3. Rotate the shade (E) so that the notch in the base of the shade is positioned over the tab located on the socket assembly.
4. Remove the shade (E) by pulling it straight out from the socket assembly.
5. To remove a bulb (C) already installed in the lamp, grasp it firmly and pull it straight out of the socket. Do not twist or bend the bulb while removing it from the socket.
6. To install a bulb (C) in the socket, grasp the bulb firmly, position it so that the pins are aligned with the socket receptacles, then push the bulb straight into the socket until it "snaps" into place.
7. To replace the shade (E), align the notch of the shade with the tab of the socket housing, then push it back into the socket assembly, ensuring the shade "snaps" into place.

Note: OttLite® tubes are not dimmable during operation.

Product Details & Replacement Parts

This lighting system is designed for use with OttLite® tubes type (style number PL13-E). Use of other products voids the warranty and may result in damage to the lighting system.

For more information on purchasing replacement tubes/bulbs, please visit: www.OttLite.com/replacement13wtube