Danze Cirtangular Collection Two Piece High Efficiency Toilet Installation Instructions

Introduction to Danze

Thank you for choosing Danze. We believe that elements in your bathroom should awaken your senses like a splash of cool water. That's what you will experience with Danze.

Danze is a manufacturer of high quality decorative plumbing products for your powder room, kitchen and bath. We offer a broad variety of products, designs & finishes to suit your own particular needs. You can feel confident that our products will provide years of beauty and trouble-free performance.

Danze Vitreous China Products

Danze vitreous china products include toilets, bidets and lavatories. Our fixtures reflect state-of-the-art design and engineering, and meet or exceed the most rigorous plumbing codes throughout North America. Operating fixtures are equipped with first quality valves and accessories to give you years of trouble-free service.

For questions about your Danze purchase, contact us at our website www.danze.com, or call our technical service center during business hours at 888-328-2383.

Danze, Inc. reserves the right to make product specification changes and to change or discontinue models without notice or obligation in North America.

This toilet has been designed for easy installation. Conventional fittings have been used throughout so that the working parts and operation of this assembly may be easily understood. Local Plumbing and Building Codes should be followed for all installations.

Do not expose plastic trim parts to strong oxidizing agents, chlorine, or acid levels of lower than 5.0 pH. Most bowl/ tile cleaners contain such agents.

Tank type bowl cleaners can cause tank component failure and damage. Our warranty excludes such failures.

Before Installation

Toilet Tank Parts Included:

• (B) Toilet Tank For Toilet Bowl Model DC023330 only
• (M) Toilet Tank Cover
• (Q) Toilet Tank assembly bag containing:
  • (C) Toilet Tank Mounting Bolts (2 each)
  • (D) Rubber Toilet Tank Bolt Washers (2 each)
  • (E) Plastic Wing Nuts (4 each)
  • (F) Toilet Tank to Bowl Gasket (1 each)
• (G) Channel Pads (2 each)
• (H) Coupling Nut and Cone Washer (1 each)
• (V) Welcome to Danze kit
• (W) Installation Instructions
• (X) Homeowner Care Manual
• (Y) Warranty Parts Guide

Toilet Bowl Parts Included:

• (A) Toilet Bowl For Toilet Tank Model DC022321 only
• (N) Toilet Seat
• (O) Ceramic Floor Bolt Cover Plates (2 each)
• (V) Welcome to Danze kit
• (P) Hook and Loop Tapes (6 strips)
• (W) Installation Instructions
• (X) Homeowner Care Manual
• (Y) Warranty Parts Guide

Tools Required

• Putty Knife
• Wax Ring (1 required)
• Floor Mounting Bolts, Washers and Nuts (2 each required)
• Adjustable wrench
• Carpenter's Level
• Regular Screwdriver
• Safety Glasses
• Flexible Water Supply Line* (*Optional, only required if not already in place or if the existing supply line needs to be replaced)

Product Dimensions

Diagrams show side and top views of the toilet with dimensions. Key dimensions include:

• Overall Height: 31 3/4 inches
• Tank Width: 18 1/2 inches
• Tank Depth: Approximately 8 3/4 inches
• Bowl Height: 17 1/8 inches
• Rough-in Measurement (distance from finished wall to center of drain): 12 inches
• Water Supply Connection: 3/8" S.P.S.
• Floor Mounting Bolt Slots: 1/2" x 1"

Installation Instructions

Step 1: Prepare for Installation

Turn off and disconnect the water supply. Unbolt and remove the old toilet. Remove the old wax ring and clean the floor flange area with a putty knife.

Step 2: Install Wax Ring

Install a new wax ring (not included) on the bottom of the toilet bowl (A), ensuring not to cover the toilet bowl outlet. Alternatively, the wax ring can be placed onto the floor flange.

Step 3: Position Toilet Bowl

Install new floor mounting bolts (not included) upright in the floor flange slots. Place the toilet bowl (A) over the floor flange/waste line opening, aligning the floor mounting bolts with the toilet's floor bolt holes. Press down firmly and twist the toilet bowl (A) slightly to compress the wax ring and ensure a seal between the bowl and the floor.

Step 4: Secure Floor Mounting Bolts

Place a floor mounting bolt washer (not included) over each floor mounting bolt. Assemble the floor mounting bolt nut to the floor mounting bolt. Tighten the floor mounting bolt nut carefully until it is just snug.

Step 5: Install Floor Bolt Covers

Install the ceramic floor bolt cover plates (O) (included) by firmly pressing them into the recesses on the side wall of the toilet bowl (A). Six additional strips of hook and loop tape (P) are provided for future replacements.

Step 6: Check Valve Lock Nuts

Before assembling the toilet tank (B) to the toilet bowl (A), check the tightness of the lock nuts on both the flush valve and the fill valve.

Step 7: Assemble Tank Mounting Bolts

Assemble the toilet tank mounting bolts (C) into the toilet tank (B) with the rubber toilet tank bolt washers (D) and plastic wing nuts (E). Tighten the plastic wing nuts (E) by hand sufficiently to compress the rubber washers (D) and ensure a water seal.

Step 8: Attach Tank-to-Bowl Gasket

Assemble the toilet tank to bowl gasket (F) to the flush valve shank, ensuring the lock nut is enclosed in the recess. Verify that the entire surface of the gasket (F) is in contact with the toilet tank bottom.

Step 9: Place Channel Pads

Place two channel pads (G) onto the posts on the back of the toilet bowl ledge to prevent china-to-china contact.

Step 10: Position and Level Tank

Place the toilet tank assembly (B) in position. Tighten the plastic wing nuts (E) sufficiently by hand to prevent rocking. The tank can be leveled by adjusting the tightness of the wing nuts (E) on the three contact points: the tank-to-bowl gasket (F) and the two channel pads (G).

Step 11: Connect Fill Valve Coupling Nut

Use the fill valve coupling nut (H) to connect the water supply line to the fill valve. Do not use pipe dope! Hand-tighten only. Over-tightening may split the fill valve and void the warranty.

Step 12: Connect Flexible Water Supply Line

If using a flexible water supply line (not included), assemble it to the threads of the toilet tank fill valve. Do not use Teflon tape or pipe dope on the fill valve threads, as this can lead to over-tightening and breakage.

Step 13: Check Refill Tube Adapter

Ensure the refill tube adapter (I) is attached to the top of the flush valve overflow tube. The flow from the refill tube must be positioned directly over the overflow tube.

Step 14: Clear System Debris

IMPORTANT: Always clear sand and rust from the system.

• Remove the valve top by lifting the arm and rotating the top 1/8 turn counterclockwise.
• Place a container over the uncapped valve to prevent splashing. Turn the water supply on and off a few times. Leave the water supply off.
• Replace the top by engaging the lugs and rotating 1/8 turn clockwise. Ensure the top is turned to the locked position. The valve may not operate if the top is not fully locked.

Step 15: Turn On Water and Check for Leaks

Turn on the toilet's water supply and check for leaks. Inspect connection points of the water supply line to the tank fill valve, the water supply line to the water supply valve, the bottom of the tank mounting area, and around the base of the toilet bowl (A). Carefully tighten any leaking connections.

Step 16: Adjust Water Level

Adjust the water level in the toilet tank (B) to the marked water line. Turn the water level adjustment screw (J) to move the float cup (K) up or down.

Step 17: Check Tank Lever and Flapper

Check the operation of the tank lever (L) and ensure its nut is tight (left-hand thread). Also, check the slack in the flapper chain (it should have slight slack when at rest) and the seal of the flush valve flapper.

Step 18: Place Tank Cover

Carefully place the toilet tank cover (M) onto the top of the toilet tank (B).

Step 19: Install Toilet Seat

Install the toilet seat (N) according to the manufacturer's instructions.

Please refer to the Homeowner Care Manual for troubleshooting, care, and maintenance information.