Danze Orrington Collection One Piece High Efficiency Toilet Installation Instructions

Introduction to Danze

Thank you for choosing Danze. We believe that elements in your bathroom should awaken your senses like a splash of cool water. That's what you will experience with Danze.

Danze is a manufacturer of high quality decorative plumbing products for your powder room, kitchen and bath. We offer a broad variety of products, designs & finishes to suit your own particular needs. You can feel confident that our products will provide years of beauty and trouble-free performance.

Danze Vitreous China Products

Danze vitreous china products include toilets, bidets and lavatories. Our fixtures reflect state-of-the-art design and engineering, and meet or exceed the most rigorous plumbing codes throughout North America. Operating fixtures are equipped with first quality valves and accessories to give you years of trouble-free service.

For questions about your Danze purchase, contact Danze at their website www.danze.com, or call their technical service center during business hours at 888-328-2383.

Danze, Inc. reserves the right to make product specification changes and to change or discontinue models without notice or obligation in North America.

This toilet has been designed for easy installation. Conventional fittings have been used throughout so that the working parts and operation of this assembly may be easily understood. Local Plumbing and Building Codes should be followed for all installations.

Do not expose plastic trim parts to strong oxidizing agents, chlorine, or acid levels of lower than 5.0 pH. Most bowl/tile cleaners contain such agents.

Tank type bowl cleaners can cause tank component failure and damage. Danze's warranty excludes such failures.

Before Installation

Check included parts:

• (A) One-piece Toilet Model DC011323 ?
• (M) Toilet Tank Cover ?
• (H) Coupling Nut and Cone Washer (1 each) ?
• (N) Toilet Seat ?
• (O) Ceramic Floor Bolt Cover Plates (2 each) ⚪
• (V) Welcome to Danze Kit ?
• (P) Hook and Loop Tape (6 strips) Velcro Tape
• (W) Installation Instructions ?
• (X) Homeowner Care Manual ?
• (Y) Warranty Parts Guide ?

Tools Required

• ? Putty Knife
• ? Wax Ring (1 required)
• ? Floor Mounting Bolts, Washers and Nuts (2 each required)
• ? Adjustable Wrench
• ? Carpenter's Level
• ? Regular Screwdriver
• ? Safety Glasses
• ? Flexible Water Supply Line* (*Optional, only required if not already in place or the existing supply line needs to be replaced)

Product Dimensions

Diagram showing dimensions of the toilet. Key measurements include:

• Finished Wall to Toilet Outlet: 12"
• Overall Height: approximately 28 7/8"
• Tank Height: approximately 16 1/2"
• Seat Height: approximately 15"
• Bowl Width: approximately 19 1/8"
• Tank Width: approximately 9 1/8"
• Flange to Wall Clearance: 12"
• Water Supply Connection: 3/8" S.P.S. SUPPLY
• Floor mounting bolt slot: 1/2"x1"

Installation Instructions

Step 1:

Turn off and disconnect water supply. Unbolt and remove old toilet. Remove old wax ring and clean floor flange area with putty knife.

Step 2:

Install new wax ring (not included) on the bottom of the toilet (A), ensuring not to cover the toilet outlet. (Alternate Method: The wax ring may also be placed onto the floor flange.)

Step 3:

Install new floor mounting bolts (not included) upright in the slots of the floor flange. Place the toilet (A) over the floor flange/waste line opening, aligning the floor mounting bolts with the toilet floor bolt holes. Press down firmly and twist toilet slightly to compress wax ring and assure a seal between the toilet (A) and floor.

Step 4:

Place one floor mounting bolt washer (not included) over each floor mounting bolt and assemble the floor mounting bolt nut to the floor mounting bolt. Tighten floor mounting bolt nut carefully until just snug.

Step 5:

Install the ceramic floor bolt cover plates (O) by firmly pressing them into the recesses in the side wall of the toilet (A). (Six additional strips of hook and loop tape (P) are provided for replacements.)

Step 6:

Use the fill valve coupling nut (H) to connect the water supply line to the fill valve. Do not use pipe dope. Hand tighten only, as overtightening may split the fill valve and void the warranty.

Step 7:

If using a flexible water supply line (not included), assemble it to the threads of the tank fill valve. Do not use Teflon tape or pipe dope on the fill valve threads to prevent over-tightening and breakage.

Step 8:

Ensure the refill tube adapter (I) is attached to the top of the flush valve overflow tube. Note: The flow from the refill tube must be positioned directly over the overflow tube.

Step 9: IMPORTANT:

Always clear sand and rust from the system.

• Remove valve top by lifting the arm and rotating the top 1/8 turn counterclockwise.
• While holding a container over the uncapped valve to prevent splashing, turn water supply on and off a few times. Leave water supply off.
• Replace top by engaging lugs and rotating 1/8 turn clockwise. Ensure the top is turned to the locked position. The valve may not turn on if the top is not fully turned to the locked position.

Step 10:

Turn on water supply to the toilet and check for leakage. Inspect connection points of the water supply line to the tank fill valve, water supply line to the water supply valve, and around the base of the toilet. Carefully tighten any leaking connections.

Step 11:

Adjust water level in the tank to the marked water line. Turn the water level adjustment screw (J) to move the float cup (K) up or down.

Step 12:

Check the action and nut tightness (left hand thread) of the tank lever (L). Also, check the flapper chain for slight slack when at rest and the seal of the flush valve flapper.

Step 13:

Carefully place the tank cover (M) onto the top of the toilet (A).

Step 14:

Install the toilet seat (N) per the manufacturer's instructions.

Please refer to the Homeowner Care Manual for troubleshooting, care, and maintenance information.