Danze Cirtangular™ Collection Two Piece Toilet Installation Instructions
Model Numbers: DC023230, DC022221
For assistance, call 1-888-328-2383 or visit www.danze.com
Introduction to Danze
Thank you for choosing Danze. We believe that elements in your bathroom should awaken your senses like a splash of cool water. That's what you will experience with Danze.
Danze is a manufacturer of high quality decorative plumbing products for your powder room, kitchen and bath. We offer a broad variety of products, designs & finishes to suit your own particular needs. You can feel confident that our products will provide years of beauty and trouble-free performance.
Danze Vitreous China Products
Danze vitreous china products include toilets, bidets and lavatories. Our fixtures reflect state-of-the-art design and engineering, and meet or exceed the most rigorous plumbing codes throughout North America. Operating fixtures are equipped with first quality valves and accessories to give you years of trouble-free service.
Should you have questions about your Danze purchase, contact us at our website www.danze.com, or call our technical service center during business hours at 888-328-2383.
Danze, Inc. reserves the right to make product specification changes and to change or discontinue models without notice or obligation in North America.
This toilet has been designed for easy installation. Conventional fittings have been used throughout so that the working parts and operation of this assembly may be easily understood. Local Plumbing and Building Codes should be followed for all installations.
Do not expose plastic trim parts to strong oxidizing agents, chlorine, or acid levels of lower than 5.0 pH. Most bowl/ tile cleaners contain such agents.
Tank type bowl cleaners can cause tank component failure and damage. Our warranty excludes such failures.
Before Installation
Toilet Tank Package Contents:
- (B) Toilet Tank for Toilet Bowl Model DC023230 only
- (M) Toilet Tank Cover
- (Q) Toilet Tank assembly bag containing:
- (C) Toilet Tank Mounting Bolts (2 each)
- (D) Rubber Toilet Tank Bolt Washers (2 each)
- (E) Plastic Wing Nuts (4 each)
- (F) Toilet Tank to Bowl Gasket (1 each)
- (G) Channel Pads (2 each)
- (H) Coupling Nut and Cone Washer (1 each)
- (V) Welcome to Danze kit
- (W) Installation Instructions
- (X) Homeowner Care Manual
- (Y) Warranty Parts Guide
Toilet Bowl Package Contents:
- (A) Toilet Bowl for Toilet Tank Model DC022221 only
- (N) Toilet Seat
- (O) Ceramic Floor Bolt Cover Plates (2 each)
- (V) Welcome to Danze kit
- (P) Hook and Loop Tapes (6 strips)
- (W) Installation Instructions
- (X) Homeowner Care Manual
- (Y) Warranty Parts Guide
Tools Required
- Putty Knife: For cleaning the floor flange area.
- Wax Ring (1 required): For sealing the toilet to the floor flange.
- Floor Mounting Bolts, Washers and Nuts (2 each required): For securing the toilet bowl to the floor.
- Adjustable wrench: For tightening various fittings.
- Carpenter's Level: To ensure the toilet is level.
- Regular Screwdriver: For general adjustments.
- Safety Glasses: For eye protection during installation.
- Flexible Water Supply Line*: Optional, required if the existing supply line is not in place or needs replacement.
Product Dimensions
| Dimension | Measurement |
|---|---|
| Finished Wall to Center of Outlet | 12" |
| Overall Height | 31 3/4" |
| Overall Width | 18 1/2" |
| Overall Depth | 29 1/4" |
| Seat Height | 16 1/2" |
| Tank Width | 8 3/4" |
| Tank Depth | 5 3/4" |
| Bowl Height (to rim) | 14 3/4" |
| Bowl Depth | 15 1/4" |
| Bowl Width | 12 1/4" |
| Water Supply Connection Size | 3/8" S.P.S. |
| Floor Flange Slot Size | 1/2"x1" |
| Distance from wall to bolt holes | 7 1/8" |
| Distance from side to bolt holes | 5 1/2" |
| Distance from back to bolt holes | 5 7/8" |
| Distance from floor to water inlet | 2 3/8" |
| Distance from floor to tank bottom | 6" |
| Distance from floor to bowl rim | 19" |
| Distance from floor to tank top | 4 3/8" |
Note: Dimensions are approximate and may vary slightly.
Installation Instructions
Step 1: Prepare the Area
Turn off and disconnect the water supply. Unbolt and remove the old toilet. Remove the old wax ring and clean the floor flange area with a putty knife.
Step 2: Install Wax Ring
Install a new wax ring (not included) onto the bottom of the toilet bowl (A), ensuring the bowl outlet is not covered. Alternatively, the wax ring can be placed onto the floor flange.
Step 3: Position Toilet Bowl
Install new floor mounting bolts (not included) upright in the floor flange slots. Place the toilet bowl (A) over the floor flange/waste line opening, aligning the bowl's bolt holes with the floor mounting bolts. Press down firmly and twist the bowl slightly to compress the wax ring and create a seal between the bowl and the floor.
Step 4: Secure Toilet Bowl
Place a floor mounting bolt washer (not included) onto each floor mounting bolt. Assemble the floor mounting bolt nut to the bolt and tighten carefully until snug.
Step 5: Install Floor Bolt Covers
Install the ceramic floor bolt cover plates (O) by pressing them firmly into the recesses on the side of the toilet bowl (A). Six additional strips of hook and loop tape (P) are provided for future replacement needs.
Step 6: Check Tank Connections
Before attaching the toilet tank (B) to the toilet bowl (A), check the tightness of the lock nuts for both the flush valve and the fill valve.
Step 7: Assemble Tank Mounting Bolts
Assemble the toilet tank mounting bolts (C) into the toilet tank (B) with rubber toilet tank bolt washers (D) and plastic wing nuts (E). Tighten the wing nuts by hand sufficiently to compress the washers and ensure a water seal.
Step 8: Attach Tank-to-Bowl Gasket
Assemble the toilet tank to bowl gasket (F) onto the flush valve shank. Ensure the lock nut is within the recess and that the entire surface of the gasket (F) contacts the bottom of the toilet tank.
Step 9: Install Channel Pads
Place two channel pads (G) onto the posts at the back of the toilet bowl ledge to prevent porcelain-to-porcelain contact.
Step 10: Position and Secure Tank
Place the assembled toilet tank (B) onto the toilet bowl (A). Tighten the plastic wing nuts (E) by hand to prevent rocking. The tank can be leveled by adjusting the tightness of the wing nuts on the three contact points: the tank-to-bowl gasket (F) and the two channel pads (G).
Step 11: Connect Water Supply to Fill Valve
Use the fill valve coupling nut (H) to connect the water supply line to the fill valve. Do not use pipe dope. Hand-tighten only. Over-tightening can split the fill valve and void the warranty.
Step 12: Flexible Water Supply Line
If using a flexible water supply line (not included), connect it to the fill valve threads. Do not use Teflon tape or pipe dope, as this can lead to over-tightening and breakage.
Step 13: Refill Tube Placement
Ensure the refill tube adaptor (I) is attached to the top of the flush valve overflow tube. The refill tube's flow must be directed into the overflow tube.
Step 14: Flush System Maintenance
IMPORTANT: Always clear sand and rust from the system. To do this: Remove the valve top by lifting the arm and rotating the top 1/8 turn counterclockwise. Place a container under the valve to catch splashing water. Turn the water supply on and off a few times, then leave it off. Re-engage the top by aligning the lugs and rotating 1/8 turn clockwise until locked. The valve will not operate if the top is not fully locked.
Step 15: Check for Leaks
Turn on the water supply and check for leaks at all connection points: water supply line to fill valve, water supply line to shut-off valve, tank mounting area, and around the base of the toilet bowl (A). Carefully tighten any leaking connections.
Step 16: Adjust Water Level
Adjust the water level in the toilet tank (B) to the marked water line. Turn the water level adjustment screw (J) to raise or lower the float cup (K).
Step 17: Check Tank Lever and Flapper
Verify the tank lever (L) operates correctly and its nut is tight (left-hand thread). Check the flapper chain for slight slack when at rest and ensure the flapper seals properly.
Step 18: Install Tank Cover
Carefully place the toilet tank cover (M) onto the top of the toilet tank (B).
Step 19: Install Toilet Seat
Install the toilet seat (N) according to the manufacturer's instructions.
For troubleshooting, care, and maintenance information, please refer to the Homeowner Care Manual.
