MAULjuvis 825 86 LED Floor Lamp
Assembly and Operation Guide
Product Overview
The MAULjuvis 825 86 is an LED floor lamp designed for versatile lighting solutions. It features integrated motion and daylight sensors, as well as dimming capabilities.
Brand: MAUL
Model: MAULjuvis 825 86
Power Requirements: 200-240V~, 50/60 Hz, 80W
Cable Length: Approximately 2.50 meters
Website: www.maul.de
Safety Information: The product requires careful handling. It is recommended that two people are available for lifting and assembly. Avoid contact with water and electrical shock hazards.
Parts List
- Part 1: Base (1x)
- Part 2: Lamp Head Assembly (1x)
- Part 3: Lower Pole Section (1x)
- Part 4: Upper Pole Section (1x)
- Part 5: Screws M4 x 25 (3x)
- Part 6: Screws M4 x 12 (3x)
- Part 7: Dowels Ø4.2 (6x)
- Part 8: Screws M4 x 12 (2x)
- Part 9: Allen Key (1x)
- Part 10: Screws M4 x 12 (1x)
Assembly Instructions
Step 1: Base Attachment
Secure the base (Part 1) to the lower pole section (Part 3) using three M4 x 25 screws (Part 5) and one M4 x 12 screw (Part 10), tightened with the Allen key (Part 9).
Step 2: Pole Connection
Join the lower pole section (Part 3) and the upper pole section (Part 4). Secure this connection by inserting two M4 x 12 screws (Part 8) into the designated holes using the Allen key (Part 9).
Step 3: Lamp Head Attachment
Attach the lamp head assembly (Part 2) to the top of the assembled pole (Parts 3 & 4). Secure it using three M4 x 12 screws (Part 6) and six dowels Ø4.2 (Part 7).
Step 4: Final Securing
Secure the lamp head assembly (Part 2) to the pole using two M4 x 12 screws (Part 8).
Sensor and Dimming Functions
The MAULjuvis 825 86 features a motion sensor and a daylight sensor, controlled via a rotary switch and an internal dip switch.
Dip Switch Settings
The dip switch, located internally, allows configuration of the motion and daylight sensors. The table below outlines the functions:
| Dip Switch Position | Motion Sensor | Daylight Sensor |
|---|---|---|
| 0 | OFF | OFF |
| 1 | ON (30 min delay) | OFF |
| 2 | ON (30 min delay) | ON |
| 3 | OFF | ON |
Sensor Operation
Motion Sensor (A)
When activated (e.g., Position 1 or 2), the light turns on when motion is detected. After a period of inactivity (e.g., 30 minutes), the light may dim or turn off. The sensor has a detection angle of up to 85° and a range of up to 3500 mm (3.5 meters).
Daylight Sensor (B)
When activated (e.g., Position 2 or 3), the light adjusts its brightness based on ambient light levels. In low light conditions, the light will turn on or increase brightness. In sufficient daylight, the light will turn off or dim.
Light Sensor Calibration
After connecting the power and selecting a sensor mode (dip switch positions 2 or 3), the luminaire can be switched on using the rotary switch. The light sensor will automatically calibrate to the room's ambient lighting conditions within a few minutes before adapting its output.
Dimming Function
The rotary switch on the lamp allows for manual control, including turning the light ON/OFF and adjusting the brightness (dimming).
Spare Parts
The following article numbers are available for spare parts:
- Art.-No.: 8258309.205A (LED module)
- Art.-No.: 8258309.210 (Power supply/driver)
- Art.-No.: 8258609.220 (Control board)
- Art.-No.: 8258609.225 (Connector board)
- Art.-No.: 8258309.200A (Main lamp assembly, likely the 2-light source version)
Energy Efficiency Information
This product contains light sources with an energy efficiency class of < C. (Refer to specific article numbers for details on single or dual light sources).
maul.de
