CZEview Solar Surveillance Camera - User Manual

Important Safety Instructions

The battery-powered camera is designed for motion detection and live streaming on demand, not continuous 24-hour operation. Follow all warnings and instructions on the product. Use only manufacturer-recommended accessories. Turn off the device when not in use for extended periods. Charge the camera using the specified power source and do not use solar panels from other brands. Do not attempt to disassemble; contact authorized service centers for maintenance. Supervise children to prevent them from playing with the product. Keep small, detachable parts away from children to prevent choking hazards. Not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless supervised or instructed by a responsible person. Ensure the solar panel receives sufficient sunlight and is not obstructed by trees or buildings. Clean the solar panel regularly to maintain optimal light absorption.

Battery Information

The battery is integrated and cannot be removed. Charge the battery between 0°C and 45°C, and use it between -20°C and 50°C. Keep the charging connector dry and clean. Do not charge, use, or store the battery near ignition sources. If the battery emits an odor, generates heat, changes color, deforms, or shows other abnormalities, discontinue use immediately and contact the seller. Avoid extreme temperatures and pressures. Do not dispose of the battery in fire or attempt to damage it mechanically. Dispose of used batteries according to guidelines to minimize environmental damage.

Precautions

Handle batteries with care to avoid burns, fire, and explosions. Protect the product from extreme temperatures and prolonged sun exposure. Keep cables out of reach of children to prevent strangulation. Be aware of potential interference from other electronic devices and position the camera unit accordingly.

What's Included

• Solar Camera
• Power Cable
• Screw Pack
• Wall Mount Bracket
• Mounting Strap
• User Manual

Product Overview

The solar camera features a solar panel, antenna, reset button, power button, PIR motion sensor, microphone, infrared sensor, lens, speaker, charging indicator, and power input. The reset button is used to reset the device (hold for 3-6 seconds), and the power button is used to turn the device on or off (hold for 3-6 seconds). The charging indicator shows red for charging and blue when fully charged. The PIR motion sensor has a detection range of up to 10 meters and a horizontal angle of 130°.

Specifications

Preparation

Local Monitoring

A Micro SD card (up to 256GB, not included) is required for recording and storage. It is optional if you do not need to store videos and images.

Cloud Storage Options

Choose a cloud storage plan for videos, with additional backup and extra features. Subscription is available after connecting the device in the app.

Setting Up the System

Download the App

Download 'CZEview' from the App Store (iOS) or Google Play (Android) by scanning the QR code provided.

Configuring the Camera in the App

1. Fully charge the camera before first use.
2. Press and hold the 'Power' button for 3-6 seconds until you hear three rapid 'Ding, Ding, Ding' sounds, indicating the camera has started.
3. Ensure the red light is flashing slowly, indicating it is ready for Wi-Fi configuration.
4. If the red light is not flashing, press the 'Power' button to activate the camera, then press and hold the 'Reset' button for 3-6 seconds until you hear a 'cuckoo' sound. The red light will flash slowly, indicating it is ready for Wi-Fi configuration.
5. Ensure the CZEview app is downloaded and open.
6. Select the correct device type and model in the app.
7. Ensure your network is stable and keep the camera and phone close to the router during setup.
8. Enter your Wi-Fi password (8-32 characters). Do not use emojis, special characters, or symbols in the Wi-Fi name or password. Avoid public networks.
9. Web authentication networks are not supported.
10. Ensure your Wi-Fi network name (SSID) is visible.
11. VPN and proxy servers are not compatible.

Method 1: Bluetooth Connection (Recommended)

Allow the app to access your Bluetooth and location services for a successful connection.

1. On the Home page, select 'Scan code' to add a device. Align the camera with the QR code on the camera body's sticker.
2. The camera to be connected will be displayed. Tap 'Access configuration' to proceed.
3. Follow the on-screen instructions to complete the next steps.
4. Select the same Wi-Fi network your phone is connected to and enter the password.
5. Allow the app to access your location.
6. Wait for a 'cuckoo' sound, indicating the connection has started. The indicator light should turn solid blue, confirming successful configuration. Then, allow the app to connect the camera to your local network and tap 'Next' to name your camera.

Attention:

If a 'connection error' message appears during Wi-Fi setup, tap 'Add again' and follow these steps:

• If the indicator light is on: Press and hold the 'Reset' button for 3-6 seconds until you hear a 'cuckoo' sound, indicating the camera is in reset mode. The light will flash red and emit three rapid 'Ding, Ding, Ding' sounds, indicating the camera is starting up and ready for Wi-Fi configuration. Follow the on-screen instructions to complete the connection.
• If the indicator light is off: Press the 'Power' button to turn on the light and listen for three rapid 'Ding, Ding, Ding' sounds. Press and hold the 'Reset' button for 3-6 seconds until you hear a 'cuckoo' sound, indicating reset mode. The light will flash red and emit three rapid 'Ding, Ding, Ding' sounds, indicating the camera is starting up and ready for Wi-Fi configuration. Follow the on-screen instructions to complete the connection.

If the above steps do not work, tap 'Other Methods' and refer to the 'Important Tips' section, or contact support@czeview.net.

Installing the Camera

1. Perform a network diagnosis. Place the camera in the intended installation area and open the app. Tap the 'Settings' icon, then 'Installation Guide', and 'Network Diagnostic'. Ensure the Wi-Fi signal strength is 'Strong' at the installation point for optimal performance.
2. For optimal results, install the camera on a wall at a height of approximately 2.5 meters. Ensure there are no obstructions within 1 meter of the camera's horizontal field of view. Avoid placing the camera behind trees or around corners, as this may affect night vision quality.

Using the Wall Mount Bracket

1. Fix the wall mount bracket to a drillable surface with screws.
2. Slide the camera into the wall mount bracket until it clicks into place.

Using the Strap

1. Pass the strap through the opening in the wall mount bracket.
2. Pass the strap through the buckle, tighten it, and secure it to a pole or tree.

Tips for Optimal Motion Detection:

A. Camera Installation Based on Field of View:

1. Check the camera's viewing angle to ensure the monitoring area is within its field of view.
2. The ideal viewing distance is 2-10 meters for optimal recognition. For best results, avoid placing the camera too far or too high; the recommended height is 2.5 meters.

B. Installation Based on PIR Motion Sensor Detection:

1. The PIR motion sensor detects motion within a maximum distance of 10 meters and a horizontal angle of 130°. Ensure movements are within this range to be detected.
2. The PIR sensor is more sensitive to side-to-side movements than direct movements towards the camera.

Tips for Reducing False Alarms:

• Avoid installing the camera facing bright lights, including the sun and bright lamps.
• Do not point the camera lens directly at the street; it is recommended to position the camera at least 10 meters away from driveways or roads.
• Keep the camera away from vents like air conditioning vents, humidifiers, and projector vents.
• Avoid placing the camera facing mirrors or glass surfaces.
• Keep the camera at least 1 meter away from any wireless devices, including Wi-Fi routers, to avoid interference.

Tips for Improving Detection Accuracy:

• Set the sensitivity level to high.
• Position the camera to detect lateral movements rather than direct movements for better motion detection.
• Mount the camera at an optimal height of 2.5 meters. Avoid placing it too low or too high, as this may affect alarm detection.
• Ensure the target is within the ideal PIR sensor detection range of 2-10 meters.

Night Vision

To adjust night vision settings, open the app and go to 'Settings → Image Settings → Full Color Mode'. You can choose from three night vision modes.

Note: Night vision quality can be affected by nearby obstructions. Ensure there are no obstructions within 1 meter of the camera's horizontal field of view. Avoid placing the camera behind trees or corners.

Recording and Playback

CZEview battery-powered cameras record only when motion is detected, not continuously. Recordings can be saved to a micro SD card (not included) or the cloud (subscription required).

Before Recording:

For SD Card Users:

• Use a micro SD card with a capacity between 8GB and 256GB. (A 32GB SD card can store up to 6 months of video as a reference.)
• After inserting the SD card, go to 'Settings' → 'Recording Management' to check if 'SD Card Capacity' appears in the app. If so, tap 'Format' to prepare the card.
• If 'SD Card Capacity' is not displayed, reinsert the SD card and check again in 'Recording Management'. If the problem persists, try another SD card.

For Cloud Storage Users:

• The camera includes a basic free cloud storage with 7-day retention, where motion-activated videos are saved for 7 days before being overwritten.
• The free cloud storage plan records 6-second clips. For longer recordings, consider subscribing to another cloud storage plan or using an SD card.

Recording Configuration:

For Cloud Storage Users:

• Tap the 'Settings' icon in the bottom right of the preview window.
• Go to 'Cloud Storage Service' and tap it.
• Subscribe to a plan to enable recording; without a subscription, the camera will not record.
• Go back to 'Settings', find 'Motion Detection', and tap it.
• Ensure the 'Motion Detection' function is enabled (it is enabled by default).

For SD Card Users:

• Tap the 'Settings' icon in the bottom right of the preview window.
• Go to 'Recording Management' and tap it.
• Ensure the 'Video' switch is enabled (it is enabled by default).
• Go back to 'Settings', find 'Motion Detection', and tap it.
• Ensure the 'Motion Detection' function is enabled (it is enabled by default).

Playback:

For Cloud Storage Users:

• On the Home page, tap the playback icon ▶️.
• Tap 'Cloud' to view videos saved in the cloud.
• For a paid cloud storage plan, the default recording time is 10 seconds. To extend it, go to 'Settings' → 'Motion Detection'. The basic cloud storage plan only supports 6-second recordings.

For SD Card Users:

• On the Home page, tap the playback icon ▶️.
• Tap 'History' to view videos saved on the SD card.
• The default recording time is 10 seconds. To extend it, go to 'Settings' → 'Motion Detection'.

Important Tips

For detailed instructions on 'Configuring the Camera in the App', 'App Functions', and 'Troubleshooting', scan the QR code below.