FUFU&GAGA Shoe Cabinet Assembly Instructions

Important Information & Warnings

Please read the entire manual before starting to assemble and/or use this product. Follow the manual thoroughly and keep it for further reference.

ℹ️ IMPORTANT INFORMATION!

AVOID SCRATCHES! In order to avoid scratching, this furniture should be assembled on a soft layer, such as a rug.

IMPROVE EFFICIENCY! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

⚠️ ANTI-TOPPLE WARNING!

Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.

IMPORTANT! It is important that any product which is assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product.

Maintenance and Cleaning: For the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag.

Installation Caution: Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.

Tools Required

? Screwdriver (+)

? Electric Drill (use with caution)

? Hammer

When installing, please carefully confirm whether each screw corresponds to the manual; accessories with similar shapes can be distinguished by size.

Parts List

Main Panels:

Part 1:

Top Panel

Part 2:

Shelf Panel

Part 3:

Shelf Panel

Part 4:

Shelf Panel

Part 5:

Left Side Panel

Part 6:

Right Side Panel

Part 7:

Bottom Panel

Part 8:

Back Panel (x2)

Part 9:

Back Panel Connector/Support

Part 10:

Back Panel

Part 11:

Leg (x4)

Part 12:

Drawer Front/Base (x3)

Part 13:

Drawer Side/Support (x3)

Part 14:

Drawer Side/Support (x3)

Hardware:

Screw A:

Ø6x35mm (Ax12)

Screw B:

Ø15x10mm (Bx3)

Screw C:

Ø6x30mm (Cx3)

Screw D:

Ø4x35mm (Dx6)

Screw E:

Ø3.5x12mm (Ex3)

Screw F:

Ø3.5x14mm (Fx28)

Screw G:

Ø3.5x14mm (Gx6)

Screw H:

Ø3.5x12mm (Hx24)

Screw J:

Ø3x12mm (Jx18)

Screw L:

Ø3x12mm (Lx18)

Dowel C:

Ø6x30mm (Cx3)

Cam Lock G-1:

(Gx6)

Cam Lock G-2:

(Gx6)

Cam Lock G-3:

(Gx6)

Cam Lock B:

(Bx3)

Cam Lock C:

(Cx3)

Knob K-1:

(Kx6)

Knob K-2:

(Kx6)

Knob K-3:

(Kx6)

Wall Attachment I-1:

(Ix2)

Wall Attachment I-2:

(Ix2)

Wall Attachment I-3:

(Ix2)

Assembly Instructions

Step 1: Prepare Side Panels

Insert quickfit screw (A, Ø6x35mm) into the corresponding pre-drilled holes on plates 1 (top panel), 5 (left side panel), and 6 (right side panel) as shown.

Step 2: Insert Cam Locks

Knock cam lock parts (G-1 and G-2) slightly into the corresponding holes on plates 5 (left side panel) and 6 (right side panel) as shown.

Step 3: Attach Shelves to Left Side Panel

Attach plates 2, 3, and 4 (shelf panels) to plate 5 (left side panel) using wooden dowels (C, Ø6x30mm) and turn cam locks (B) clockwise to tighten as shown.

Step 4: Attach Right Side Panel

Cover plate 6 (right side panel) to plates 2, 3, and 4 (shelf panels) using wooden dowels (C, Ø6x30mm) and turn cam locks (B) clockwise to tighten as shown. This forms the main frame structure.

Step 5: Attach Bottom Panel

Attach plate 7 (bottom panel) to plates 5, 4, and 6 using wooden dowels (C, Ø6x30mm) and screws (D, Ø4x35mm) as shown.

Step 6: Attach Legs

Fix leg 11 to the bottom of plate 7 (bottom panel) with screws (F, Ø3.5x14mm) as shown.

Step 7: Attach Top Panel

Cover plate 1 (top panel) to plates 5, 2, and 6 using wooden dowels (C, Ø6x30mm) and turn cam locks (B) clockwise to tighten as shown. This completes the main cabinet assembly.

Step 8: Install Back Panels

Fix back plates 8 and 10 to the rear of the cabinet using screws (J, Ø3x12mm) and (L, Ø3x12mm) as shown. Ensure plates 8 and 10 connect with plank 9.

Step 9: Assemble Drawer Supports

Fix part (E) (drawer support components) to plates 13 and 14 (drawer sides/supports) with screws (H, Ø3.5x12mm) as shown. Pay attention to the holes where the accessories are inserted.

Step 10: Attach Drawer Fronts and Knobs

Attach plate 12 (drawer front/base) to part (E) with screws (H, Ø3.5x12mm) as shown. Fix knobs (K-3) to plate 14 with screws (K-2, K-1) as shown.

Note: This step appears to be repeated for each of the three drawers.

Step 11: Install Drawer Components

Fix part (E) (drawer components) to the side plates (likely referring to the main cabinet side panels or drawer sides) with part (G-3) and screws (F, Ø3.5x14mm) as shown.

Step 12: Insert Drawer Bases

Insert plate 12 (drawer base/front) into the middle of the drawer assembly as shown.

Note: This step is likely repeated for all three drawers.

Step 13: Wall Attachment (Safety Feature)

This step details how to secure the shoe cabinet to the wall for safety.

Instructions:

• Use wall attachment parts (I-1, I-2, I-3) and screws (H, Ø3.5x12mm).
• Drill holes in the wall as needed.
• I-2 cushion blocks can be installed only when there is a gap between the back plate and the wall.
• Secure the cabinet to the wall using the provided hardware.

Recommendation: Always secure tall furniture to the wall to prevent tipping.

Warranty Information

WARRANTY CLAIMS

• There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
• Before making a claim, please call us. Please leave your purchase order number, along with some details of the problem, if you want a replacement part. We will arrange within 48 hours. If there is out of stock, we will reply with a shipping date.
• The product must be used in accordance with the instructions provided. For health reasons.
• For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.

Type of Warranty Claim

• Failure to follow the furniture instructions will invalidate the warranty.
• Does not include damage during installation, but includes damage during transportation.

Scope of Responsibility

• FUFU&GAGA shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
• After use, damage and scratches of the furniture are not covered by the warranty.

The Warranty Relates to All Bought in The US and Covers The Following Areas

• Sheet parts: 1 month from the date of purchase.
• Electrical parts: 1 month from the date of purchase.

Returns Policy

CHANGED YOUR MIND AND NEED TO RETURN YOUR ITEM?

PLEASE FOLLOW THE BELOW INSTRUCTIONS:

• If you have purchased and have simply changed your mind, follow the retailer's instructions for returns.

DEFECTIVE ITEMS

• If your item is defective in any way, i.e., it doesn't work but you can't identify why, in the first instance, please call FUFU&GAGA.

DAMAGED ITEMS

• If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is refused. If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.
• In all circumstances, please save all packaging material and paperwork for the order.
• Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardize your chances of making a claim, and you may not receive a credit for the return.