Assembly Instructions
Contact Us
We're here to help you.
Your satisfaction is our top priority. If you encounter any issues with this product, such as missing or damaged parts, we're here to help. Please retain the original packaging and take photos of the packaging and the product, then contact us as soon as possible.
Warm Tips
- Carefully read these instructions and keep them for future reference.
- Check the parts list and confirm everything's there before starting assembly.
- When assembling, put all parts on a soft, smooth surface like a carpet to avoid scratches.
- Don't fully tighten screws until all parts are confirmed in place to avoid misalignment.
Tools and Safety
We recommend using hand tools for assembly. If an electric screwdriver is used, reduce power and torque to avoid damage to the product.
Install the Anti-Tip Straps
Using the anti-tip straps can reduce the risk of tipping over, but can not eliminate it. Ensure the furniture is securely anchored to the wall to prevent tipping.
Parts List
| Part | Description | Quantity |
|---|---|---|
| 1 | Long top/base panel | 1 pc |
| 2 | Vertical leg panels | 4 pcs |
| 3 | Long connecting/support beams | 2 pcs |
| 4 | Small connecting brackets/supports | 2 pcs |
| 5 | Small shelf/support panels | 2 pcs |
Hardware List
| Code | Description | Quantity |
|---|---|---|
| A | Screw (Ø6x35 mm) | X38+1 |
| B | Screw (Ø15x12 mm) | X38+1 |
| C | Screw (Ø8x30 mm) | X12+1 |
| D | Screw (M6x30 mm) | X8+1 |
| E | Screw (M4x64 mm) | X1 |
| F | Screw (3.5x14 mm) | X2+1 |
| G | Screw (4x35 mm) | X2+1 |
| H | Screw (Ø8x40 mm) | X2 |
| I | Cable/Strap (L250 mm) | X2 |
| J | Screw (M6xØ30 mm) | X8 |
| K | Screw (26x13 mm) | X4 |
Assembly Steps
Step 1
Attach part 1 (long panel) to two parts 2 (leg panels) using hardware A (screws, Ø6x35 mm). Insert screws from the underside of part 1 into the top edges of parts 2.
[Diagram shows part 1 positioned horizontally, with two parts 2 vertically attached to its ends. Screws 'A' are shown being inserted into pre-drilled holes.]Hardware Used: A (X38)
Step 2
Attach two parts 5 (small shelf/support panels) to the inner sides of two parts 2 (leg panels) using hardware J (screws, M6xØ30 mm) and hardware B (screws, Ø15x12 mm). Insert hardware J through the outer face of part 2 into the edge of part 5. Insert hardware B through the inner face of part 2 into the edge of part 5.
[Diagram shows two leg assemblies (part 2) each with a shelf (part 5) attached. Screws 'J' are shown entering from the outside of part 2 into part 5, and screws 'B' are shown entering from the inside of part 2 into part 5.]Hardware Used: B (X8), J (X8)
Step 3
Attach the two parts 3 (long connecting beams) to the inner sides of the leg assemblies (parts 2) using hardware B (screws, Ø15x12 mm) and hardware C (screws, Ø8x30 mm). Insert screws B from the outer face of part 2 into the edge of part 3. Insert screws C from the inner face of part 2 into the edge of part 3.
[Diagram shows the two leg assemblies connected by two long beams (part 3). Screws 'B' are shown entering from the outside of part 2 into part 3, and screws 'C' are shown entering from the inside of part 2 into part 3.]Hardware Used: B (X8), C (X8)
Step 4
Attach the two parts 4 (small connecting brackets) to the ends of the long connecting beams (part 3) using hardware B (screws, Ø15x12 mm). Insert screws B through the holes in part 4 into the ends of part 3.
[Diagram shows the two long beams (part 3) being attached to the small brackets (part 4) at their ends. Screws 'B' are shown securing part 4 to part 3.]Hardware Used: B (X8)
Step 5
Attach the two parts 3 (long connecting beams) to the inner sides of the leg assemblies (parts 2) using hardware B (screws, Ø15x12 mm) and hardware C (screws, Ø8x30 mm). Insert screws B from the outer face of part 2 into the edge of part 3. Insert screws C from the inner face of part 2 into the edge of part 3.
[Diagram shows the two leg assemblies connected by two long beams (part 3). Screws 'B' are shown entering from the outside of part 2 into part 3, and screws 'C' are shown entering from the inside of part 2 into part 3. This step appears to be a repetition or clarification of Step 3, possibly showing a different angle or specific connection points.]Hardware Used: B (X14), C (X4)
Step 6
Attach the main top panel (part 1) to the leg assemblies using hardware D (screws, M6x30 mm) and hardware E (screw, M4x64 mm). Insert screws D through the top of part 1 into the leg assemblies. Insert screw E through the top of part 1 into the central support.
[Diagram shows the main top panel (part 1) being attached to the assembled base structure. Screws 'D' are shown securing part 1 to the top of the leg assemblies. Screw 'E' is shown securing part 1 to a central support beam.]Hardware Used: D (X8), E (X1)
Step 7: Install Anti-Tip Straps (Part 1)
Attach one end of the strap (I, L250 mm) to the back of the furniture using hardware F (screws, 3.5x14 mm) and hardware K (screws, 26x13 mm). Secure the strap to the top rear edge of the furniture.
[Diagram shows a strap being attached to the back of the furniture. Screws 'F' and 'K' are used to secure the strap to the furniture.]Hardware Used: F (X2), K (X2)
Step 8: Install Anti-Tip Straps (Part 2)
Mark the wall at the desired height for the anti-tip strap. Drill a hole in the wall at the marked location. Insert a wall anchor (implied) into the drilled hole. Secure the other end of the strap (I) to the wall using hardware G (screws, 4x35 mm) and hardware K (screws, 26x13 mm).
[Diagram shows a person marking a wall, then drilling a hole, and inserting a wall anchor. Another diagram shows the strap being secured to the wall with screws 'G' and 'K'.]Hardware Used: G (X2), K (X2)
Step 9: Install Anti-Tip Straps (Part 3)
Repeat Step 8 for the second strap. Ensure both straps are securely fastened to the furniture and the wall.
[Diagram shows the completed installation with both anti-tip straps attached to the furniture and the wall.]Hardware Used: I (X2), G (X2), K (X2)
Thank you for your support!
