Assembly Instructions
Round Table
Contact Us
We're here to help you.
Your satisfaction is our top priority. If you encounter any issues with this product, such as missing or damaged parts, we're here to help. Please retain the original packaging and take photos of the packaging and the product, then contact us as soon as possible.
Warm Tips
- Carefully read these instructions and keep them for future reference.
- Check the parts list and confirm everything's there before starting assembly.
- When assembling, put all parts on a soft, smooth surface like a carpet to avoid scratches.
- Don't fully tighten screws until all parts are confirmed in place to avoid misalignment.
Tools and Preparation
[2 people] are recommended for assembly.
Recommended tools: [wrench], [screwdriver].
We recommend using hand tools for assembly. If an electric screwdriver is used, reduce power and torque to avoid damage to the product.
Diagram showing preparation: A person looking confused at parts, followed by a person looking frustrated, then a person holding a box, and finally a person pointing to parts, indicating the need to check all components before starting.
Parts Overview
Diagram showing an exploded view of the round table components: four segments of the round tabletop (labeled 1), a circular base support (labeled 3), four angled leg pieces (labeled 2), a cross brace (labeled 4), and a connecting piece (labeled 5).
Parts List
Part 1: Curved Tabletop Segment (4 pcs)
Part 2: Angled Leg Piece (4 pcs)
Part 3: Circular Base Support (1 pc)
Part 4: Cross Brace (1 pc)
Part 5: Connecting Piece (1 pc)
Hardware List
A: Bolt (M6x15mm) (13 pcs + 1 pc)
B: Bolt (M6x30mm) (8 pcs + 1 pc)
C: Screw (φ7x47mm) (24 pcs + 1 pc)
D: Wooden Dowel (φ10x50mm) (8 pcs + 1 pc)
E: Washer (4 pcs)
F: Bracket/Plate (2 pcs)
G: Allen Key (1 pc)
Assembly Steps
Step 1
Attach the angled leg pieces (2) to the circular base support (3) using hardware A (M6x15mm bolts) and brackets F.
Diagram shows four leg pieces (2) being attached to the circular base (3) with bolts (A) and brackets (F).
Step 2
Attach the assembled base structure to the underside of the round tabletop (1) using hardware C (φ7x47mm screws).
Diagram shows the base assembly being connected to the tabletop (1) with screws (C).
Step 3
Insert wooden dowels (D) into the pre-drilled holes on the segments of the round tabletop (1).
Diagram shows dowels (D) being inserted into the edge of tabletop segments (1).
Step 4
Insert more wooden dowels (D) into the remaining pre-drilled holes on the segments of the round tabletop (1).
Diagram shows dowels (D) being inserted into the edge of tabletop segments (1).
Step 5
Attach the assembled base structure to the tabletop segments (1) using hardware A (M6x15mm bolts) and hardware B (M6x30mm bolts).
Diagram shows the base structure being secured to the tabletop segments (1) using bolts (A) and (B).
Step 6
Complete the assembly by securing various parts using hardware A (M6x15mm bolts), hardware C (φ7x47mm screws), and hardware E (washers).
Diagram shows final connections being made with bolts (A), screws (C), and washers (E).
Step 7
The round table is now fully assembled.
Diagram shows the completed round table.
Usage and Safety Guidelines
The table is designed to support weight. Ensure weights are distributed evenly on the tabletop.
Diagrams show the table with weights on top, indicating correct weight distribution with checkmarks [check mark].
Warning: Do not overload or place weights unevenly, as this may cause the table to tip.
Diagram shows the table tipping over with weights, indicating a hazard with a cross mark [cross mark].
Do not sit or press on the table side.
Diagrams show a person sitting on the table with a cross mark [person sitting on table with cross], and a person pressing down on the table edge with a cross mark [person pressing table edge with cross].
Thank you for your support!
