JABLOTRON JA-110N-DIN Bus Power PG Module - DIN Rail Mount
Brand: JABLOTRON
Product Type: Bus Power PG Module
Introduction
This document provides information for the JABLOTRON JA-110N-DIN Bus Power PG Module. It is part of the JABLOTRON system and features a PG output with a relay switch, suitable for controlling devices such as lighting and fans. Installation requires a qualified professional holding a valid certificate from an authorized distributor. For any uncertainties or errors, please refer to the original English document or contact JABLOTRON technical support.
Installation
Only qualified professionals may connect electrical devices.
Always switch off the power supply when connecting the module to the system bus.
- Mount the module onto the DIN rail.
- Connect the bus cable to the connectors (1).
- You can test the module's operation by pressing the button (4). Upon power-up, the red RELAY LED (2) will illuminate.
- Connect the controlled device to the output connectors (5).
Note: If communication is lost, the yellow STATUS LED (3) will indicate this condition, and the relay will switch to its resting state after 60 seconds.
Figure 1: Module Components
The module features the following external parts:
- 1 - Bus connectors
- 2 - RELAY LED indicator
- 3 - STATUS LED indicator
- 4 - LEARN/MANUAL trigger button
- 5 - Relay connectors
System Registration and Settings
Depending on the control panel type, use the recommended software or application; refer to the control panel manual.
Technical Specifications
| Parameter | Specification |
|---|---|
| Power Source | From the central unit bus 12 V (9-15 V) |
| Quiescent Current Consumption (relay off) | 5 mA |
| Maximum Current Consumption (relay ON) | 45 mA |
| Relay Contact Load: (galvanically and safely isolated from the bus) | |
| Maximum Switched Voltage | 250 V AC / 24 V DC |
| Resistive Load (cos φ = 1) | max. 16 A |
| Inductive, Capacitive Load (cos φ = 0.3) | max. 6 A |
| Halogen Lighting | max. 1000 W |
| DC Current | 384 W |
| Minimum Switchable DC Output | 0.5 W |
| Power Loss | 1.6 W |
| Power Loss for Heating the Switchboard | 1.9 W |
| Connected Wire Diameter | max. 2 x 1.5 mm² / 1 x 2.5 mm² |
| Environment | Indoor general use |
| Operating Temperature Range | -10 °C to +40 °C |
| Average Operating Humidity | 75% relative humidity, non-condensing |
| Dimensions | 18 x 90 x 64 mm (according to EN 60715 standard) |
| Weight | 65 grams |
| Testing Body | Trezor Test sro (No. 3025) |
| Complies with | EN 50130-4, EN 55032, EN IEC 62368-1, EN IEC 63000 |
Compliance and Declarations
JABLOTRON a.s. hereby declares that the JA-110N-DIN product complies with the relevant EU harmonisation legislation: Directives 2014/35/EU, 2014/30/EU, 2011/65/EU, when used as intended. The original Declaration of Conformity documentation is available on the JABLOTRON website at www.jablotron.com in the Downloads section.
[CE Mark] [UKCA Mark]
Environmental Considerations
Note: Proper disposal of this product helps conserve valuable resources and prevents potential negative impacts on human health and the environment that might otherwise result from improper waste handling. Please return the product to your retailer or contact your local municipality to find the nearest designated collection point.
Contact Information
JABLOTRON a.s.
Pod Skalkou 4567/33
46601 Jablonec nad Nisou
Czech Republic
Tel: +420 483 559 911
Internet: www.jablotron.com
