Assembly Instructions

Customer Support & Warm Tips

Your satisfaction is our top priority. If you encounter any issues with this product, such as missing or damaged parts, we're here to help. Please retain the original packaging and take photos of the packaging and the product, then contact us as soon as possible.

Warm Tips

1. Carefully read these instructions and keep them for future reference.
2. Check the parts list and confirm everything's there before starting assembly.
3. When assembling, put all parts on a soft, smooth surface like a carpet to avoid scratches.
4. Don't fully tighten screws until all parts are confirmed in place to avoid misalignment.

Assembly Recommendations

We recommend using hand tools for assembly. If an electric screwdriver is used, reduce power and torque to avoid damage to the product. [Tool icon: ?] [Power drill icon: ⚡?] [Cross mark icon: ❌]

AVOID SCRATCHES

In order to avoid scratching, this furniture should be assembled on a soft surface, such as a rug. [Cross mark icon: ❌] [Check mark icon: ✔️]

Parts List

Hardware List

Cam and Pin Installation Guide

Align the plastic part (cam) with the mounting hole and press it in. If it cannot be pressed in, loosen the screw counter-clockwise or remove it completely and try again. After pressing the plastic part into place, use a screwdriver [?] to tighten the screw clockwise. Screw the pin into the hole. Set the cams correctly by aligning the head of the cams with the lock pins. Lock the cam by turning the cam head with a screwdriver until it is tightened. Please do not use an electric screwdriver to assemble the unit. [Check mark icon: ✔️ No gap] [Power drill icon: ⚡?] [Cross mark icon: ❌]

Step 1

Attach hardware A (M6x35mm screws) to part 1. Repeat 4 times.

Diagram shows part 1 with four instances of hardware A being screwed into its holes.

Step 2

Attach hardware A (M6x35mm screws) to part 1. Repeat 4 times. Then attach part 2 to part 1 using hardware B (Ø15x12mm cam lock dowels). Repeat 4 times.

Diagram shows part 1 with hardware A attached, and part 2 being connected to part 1 using hardware B.

Step 3

Attach hardware A (M6x35mm screws) and hardware C (Ø8x30mm wooden dowels) to part 3. Repeat 4 times. (Total A: 12 pcs, Total C: 8 pcs used in this step).

Diagram shows part 3 with multiple holes, illustrating the insertion of hardware A and C.

Step 4

Attach part 3 to part 1 using hardware B (Ø15x12mm cam lock dowels). Repeat 4 times. (Total B: 12 pcs used in this step).

Diagram shows part 1 with part 3 being attached using hardware B.

Step 5

Attach hardware A (M6x35mm screws) and hardware C (Ø8x30mm wooden dowels) to part 5. Repeat 2 times. (Total A: 6 pcs, Total C: 4 pcs used in this step).

Diagram shows part 5 with hardware A and C being inserted.

Step 6

Attach part 5 to part 3 using hardware B (Ø15x12mm cam lock dowels). Repeat 2 times. (Total B: 6 pcs used in this step).

Diagram shows part 3 with part 5 being attached using hardware B.

Step 7

Attach hardware A (M6x35mm screws) and hardware C (Ø8x30mm wooden dowels) to part 4. Repeat 2 times. (Total A: 6 pcs, Total C: 4 pcs used in this step).

Diagram shows part 4 with hardware A and C being inserted.

Step 8

Attach part 4 to part 1 using hardware B (Ø15x12mm cam lock dowels). Repeat 2 times. (Total B: 6 pcs used in this step).

Diagram shows part 1 with part 4 being attached using hardware B.

Step 9

Attach hardware A (M6x35mm screws) and hardware C (Ø8x30mm wooden dowels) to part 6. Repeat 4 times. (Total A: 20 pcs, Total C: 16 pcs used in this step).

Diagram shows part 6 with multiple holes, illustrating the insertion of hardware A and C.

Step 10

Attach part 6 to part 1 using hardware B (Ø15x12mm cam lock dowels). Repeat 4 times. (Total B: 20 pcs used in this step).

Diagram shows part 1 with part 6 being attached using hardware B.

Step 11

Insert hardware J (Pin) into part 6. Repeat 4 times. (Total J: 16 pcs used in this step).

Diagram shows part 6 with hardware J being inserted into its holes. A caution note "Tap lightly" is present.

Step 12

Attach hardware A (M6x35mm screws) to part 7. Attach hardware D (M8x40mm screws) to part 8. Repeat 2 times. (Total A: 16 pcs, Total D: 4 pcs used in this step).

Diagram shows part 7 with hardware A being screwed in, and part 8 with hardware D being screwed in.

Step 13

Attach part 7 and part 8 together. Repeat 2 times.

Diagram shows two sub-assemblies, each consisting of part 7 and part 8 joined together.

Step 14

Attach hardware A (M6x35mm screws) to part 10. Repeat 2 times. (Total A: 4 pcs used in this step).

Diagram shows part 10 with hardware A being screwed into its holes.

Step 15

Attach hardware A (M6x35mm screws) to part 12. Repeat 2 times. (Total A: 4 pcs used in this step).

Diagram shows part 12 with hardware A being screwed into its holes.

Step 16

Attach part 11 to part 10 using hardware B (Ø15x12mm cam lock dowels). Attach part 12 to part 11 using hardware B. Repeat 2 times. (Total B: 8 pcs used in this step).

Diagram shows part 10, 11, and 12 being assembled using hardware B.

Step 17

Assemble the frame using parts 7, 8, and 11. Attach hardware B (Ø15x12mm cam lock dowels) to connect these parts. Repeat 2 times. (Total B: 16 pcs used in this step).

Diagram shows the main frame structure being assembled with multiple instances of hardware B connecting parts 7, 8, and 11.

Step 18

Attach hardware A (M6x35mm screws) and hardware C (Ø8x30mm wooden dowels) to part 13. Repeat 2 times. (Total A: 18 pcs, Total C: 8 pcs used in this step).

Diagram shows part 13 with hardware A and C being inserted.

Step 19

Attach hardware A (M6x35mm screws) and hardware C (Ø8x30mm wooden dowels) to part 14. Repeat 2 times. (Total A: 18 pcs, Total C: 8 pcs used in this step).

Diagram shows part 14 with hardware A and C being inserted.

Step 20

Attach part 13 and part 14 to the main frame using hardware E (Ø3.5x14mm screws). The diagram shows 4 instances of E on part 13 and 16 instances on part 14.

Diagram shows the tabletop panels (parts 13 and 14) being attached to the assembled frame using hardware E.

Step 21

Attach hardware B (Ø15x12mm cam lock dowels) to connect parts 8 and 14. Repeat 2 times. (Total B: 36 pcs used in this step).

Diagram shows the main frame structure with parts 8 and 14 being secured using multiple instances of hardware B.

Step 22

Attach hardware H (M6x20mm screws) to part 9. Repeat 2 times. (Total H: 4 pcs used in this step).

Diagram shows part 9 with hardware H being screwed in.

Step 23

Attach hardware F (Ø3.5x25mm screws) to part 9. Repeat 2 times. (Total F: 24 pcs used in this step).

Diagram shows part 9 being secured with multiple instances of hardware F.

Step 24

Attach hardware H (M6x20mm screws) to part 6 (legs). Repeat 4 times. (Total H: 16 pcs used in this step).

Diagram shows the legs (part 6) being attached to the table base using hardware H.

Completion

Thank you for your support!