Tribesigns Assembly Instructions

Contact Us

We're here to help you.

✉️ support@tribesigns.com

? 1-424-220-6888

Contact us anytime except 12:00 AM to 8:00 AM EST.

Your satisfaction is our top priority. If you encounter any issues with this product, such as missing or damaged parts, please retain the original packaging and take photos of the packaging and the product, then contact us as soon as possible.

Warm Tips

• 1. Carefully read these instructions and keep them for future reference.
• 2. Check the parts list and confirm everything's there before starting assembly.
• 3. When assembling, put all parts on a soft, smooth surface like a carpet to avoid scratches.
• 4. Don't fully tighten screws until all parts are confirmed in place to avoid misalignment.

How to Get the Assembly Video

Step 1: Scan the QR code. (See image of QR code labeled 'Installation Video')

Step 2: Search with the Model No. (HOGA-J0330) on the bottom left corner of the title page.

Note: If you can't find the assembly video, please contact us.

Assembly Recommendations

We recommend using hand tools for assembly. ? If an electric screwdriver is used, reduce power and torque to avoid damage to the product.

AVOID SCRATCHES

In order to avoid scratching, this furniture should be assembled on a soft surface, such as a rug. ❌ (Image showing furniture on hard surface with scratches) ✔️ (Image showing furniture on rug)

Parts List

Hardware List

Assembly Steps

Caution: Make sure all parts are included. Most board parts are labeled or stamped on the raw edge. Contact us for a free replacement if you encounter any damaged or missing parts.

Installation of Cams and Pins

Read each step carefully before starting. Each step of instruction should be performed in the correct order. If these steps are not followed in sequence, assembly difficulties may occur.

Method: Screw pin (A) into the hole. Set cams (A) correctly by aligning the head of the cams with the lock pins. Lock the cam by turning the cam head with a screwdriver ? until it is tightened. Please do not use an electric screwdriver to assemble the unit. Ensure there is 'No gap' between parts.

Step 1: Attach two panels (Part 1) to a base panel using six Ø8x30mm screws (C) and twelve M6x35mm screws (A). This process is repeated twice (x2).

Step 2: Attach two curved panels (Part 2) to a base panel using four Ø12x10mm dowels (B). This process is repeated twice (x2).

Step 3: Attach two rectangular panels (Part 3) to the structure assembled in Step 2 using eight Ø8x30mm screws (C). This process is repeated twice (x2).

Step 4: Attach two rectangular panels (Part 3) to the structure assembled in Step 3 using eight Ø12x10mm dowels (B). This process is repeated twice (x2).

Step 5: Attach the curved top sections (Part 6) to the main structure using fifty-six M7x38mm screws (D). This process is repeated twice (x2).

Step 6: Assemble the side support pieces. Connect Part 8 and Part 9 using hardware C, H, I, and J, following six sub-steps (Step 1-6). This involves inserting pins and securing with cams and screws.

Step 7: Attach the assembled side panels (from Step 6) to the main structure using four Ø6x60mm screws (K) and eight M6x35mm screws (A). This process is repeated twice (x2).

Step 8: Attach the leg structures (Part 1) to the main body using hardware B, I, and J, following five sub-steps (Step 1-5). This involves inserting dowels and securing with cams and screws.

Step 9: Attach the main table surface components (Part 11) using hardware F, G, E, and C.

Step 10: Attach the main table surface (Part 10) to the structure using four Ø8x30mm screws (C) and twelve M6x35mm screws (A).

Step 11: Attach the remaining leg/support pieces using hardware B and L.

Step 12: Attach the final support pieces using hardware M. [Rotate 90°] instruction is shown, indicating the orientation of the table.

Thank you for your support!

Contact our customer service team:

✉️ support@tribesigns.com

? www.tribesigns.com

? 1-424-220-6888

Contact us anytime except 12:00 AM to 8:00 AM EST.