myFirstech FTI-CDP1 Vehicle Preparation and Coverage Notes
Specifications
- Make: DL-CH7 Chrysler
- Model: 300 PTS
- Year: 2018
- Install Type: 2
- CAN CJB
- Lights: Park / Auto
- Type: A
- IGN BCM
Product Usage Instructions
Cartridge Installation
- Slide the cartridge into the unit, noticing the button under the LED.
Module Programming Procedure – With KLON
- Close the driver door.
- Wait for the LED to turn solid RED.
- Re-open the driver door to wake up the data bus.
- Push the start button once to the OFF position.
- Press UNLOCK on keyfob 1.
- Wait for the LED to flash BLUE once.
- Remove the valet key from keyfob 1.
- Push the start button twice with keyfob 1 to the ON position.
- If LED flashes BLUE rapidly, proceed to the next step. If LED turns solid RED, repeat steps 8 to 10.
- Push the start button once to the OFF position.
- Disconnect all connectors from remote starter except the power connector.
FAQ
- Q: What should I do if the LED does not turn solid RED during programming?
A: If the LED does not turn solid RED, repeat steps 8 to 10 of the Module Programming Procedure with KLON. - Q: Can I program multiple keyfobs with this system?
A: Yes, you can program multiple keyfobs by following the Module Programming Procedure steps for each keyfob.
RSTECH, LLE.
SUPPORT – 1(888) 820-3690, EXT. 203
- FT-DAS Required for manual transmission.
- BOTH Red & Red/White MUST be connected with high current application.
FTI-CDP1 – DL-CH7 – Type 3
2018 Chrysler 300 PTS
CARTRIDGE INSTALLATION
- Slide cartridge into unit. Notice button under LED.
- Ready for Module Programming Procedure.
MODULE PROGRAMMING PROCEDURE – WITH KLON – 1 OF 2
- Close driver door.
- Re-open driver door to wake up data bus.
Press UNLOCK on keyfob 1. - Wait, LED will fl ash BLUE once [1x].
- Remove valet key from keyfob 1.
- Remove batteries from keyfob 1.
- Push start button twice [2x] with keyfob 1 to ON position. (No battery)
- Wait, LED will turn solid RED.
- Push start button once [1x] to OFF position.
- Push start button twice [2x] with keyfob 1 to ON position. (No battery)
- Wait, if LED fl ashes BLUE rapidly, proceed to step 11. If LED turns solid RED, repeat steps 8 to 10.
- Push start button once [1x] to OFF position.
- Disconnect all connectors from remote starter except the power connector.
- Disconnect the power connector.
- Remove remote starter from vehicle.
- Connect remote starter to computer.
- Proceed with extended programming.
- Connect remote starter to vehicle.
- Close driver door.
Re-open driver door to wake up data bus. - Push start button twice [2x] with keyfob 1 to ON position. (No battery)
- Wait, LED will turn solid BLUE for 2 seconds.
- Push start button once [1x] to OFF position.
- Module Programming Procedure completed.
Insert battery in keyfob 1.
WARNING: READ BEFORE REMNO OTICETE STARTING THE VEHICLE
IMPORTANT
All OEM keyfobs must be at least 10 feet away from the vehicle. All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction.
TAKE OVER PROCEDURE – TO THE VEHICLE OWNER
NOTE
- All vehicle doors must be closed and locked prior to remote start sequence.
- Press UNLOCK on after-market remote.
- TIME RESTRICTI N
Within 45 SECONDS from previous step:- Open vehicle door.
- Enter vehicle.
- Close vehicle door.
- Press and release BRAKE pedal.
Failure to follow procedure within time restriction will result in vehicle engine shutdown.
WWW.IDATALINK.COM
Automotive Data Solutions Inc. © 2020
Documents / Resources
 |
myFirstech FTI-CDP1 Vehicle Preparation and Coverage Notes [pdf] Installation Guide FTI-CDP1 Vehicle Preparation and Coverage Notes, FTI-CDP1, Vehicle Preparation and Coverage Notes, Preparation and Coverage Notes, Coverage Notes, Notes |
 |
myFirstech FTI-CDP1 Vehicle Preparation and Coverage Notes [pdf] Installation Guide FTI-CDP1-CH7, CM7000-7200, CM900AS-900S, FTI-CDP1 Vehicle Preparation and Coverage Notes, FTI-CDP1, Vehicle Preparation and Coverage Notes, Preparation and Coverage Notes, Coverage Notes, Notes |
 |
myFirstech FTI-CDP1 Vehicle Preparation and Coverage Notes [pdf] Installation Guide DL-CH7, FTI-CDP1 Vehicle Preparation and Coverage Notes, FTI-CDP1, Vehicle Preparation and Coverage Notes, Preparation and Coverage Notes, Coverage Notes, Notes |
 |
myFirstech FTI-CDP1 Vehicle Preparation and Coverage Notes [pdf] Installation Guide DL-CH7, CM7000-7200, CM900AS-900S, CM-900, FTI-CDP1 Vehicle Preparation and Coverage Notes, FTI-CDP1, Vehicle Preparation and Coverage Notes, Preparation and Coverage Notes, Coverage Notes, Notes |
 |
myFirstech FTI-CDP1 Vehicle Preparation and Coverage Notes [pdf] Installation Guide DL-CH7, FTI-CDP1 Vehicle Preparation and Coverage Notes, FTI-CDP1, Vehicle Preparation and Coverage Notes, Preparation and Coverage Notes, Coverage Notes, Notes |
 |
myFirstech FTI-CDP1 Vehicle Preparation and Coverage Notes [pdf] Installation Guide FTI-CDP1 Vehicle Preparation and Coverage Notes, FTI-CDP1, Vehicle Preparation and Coverage Notes, Preparation and Coverage Notes, Coverage Notes, Notes |
 |
myFirstech FTI-CDP1 Vehicle Preparation and Coverage Notes [pdf] Installation Guide DL-CH7 RAM 1500 PTS Diesel 18_SPX, FTI-CDP1 Vehicle Preparation and Coverage Notes, FTI-CDP1, Vehicle Preparation and Coverage Notes, Preparation and Coverage Notes, Coverage Notes, Notes |
 |
myFirstech FTI-CDP1 Vehicle Preparation and Coverage Notes [pdf] Installation Guide FTI-CDP1 Vehicle Preparation and Coverage Notes, FTI-CDP1, Vehicle Preparation and Coverage Notes, Preparation and Coverage Notes, Coverage Notes, Notes |
 |
myFirstech FTI-CDP1 Vehicle Preparation and Coverage Notes [pdf] Installation Guide DL-CH7 RAM 2500 PTS, FTI-CDP1 Vehicle Preparation and Coverage Notes, FTI-CDP1, Vehicle Preparation and Coverage Notes, Preparation and Coverage Notes, Coverage Notes, Notes |
 |
myFirstech FTI-CDP1 Vehicle Preparation and Coverage Notes [pdf] Installation Guide DL-CH7 RAM 3500 PTS, FTI-CDP1 Vehicle Preparation and Coverage Notes, FTI-CDP1, Vehicle Preparation and Coverage Notes, Preparation and Coverage Notes, Coverage Notes, Notes |
