FIRSTECH FTI-STK1 Vehicle Coverage
FTI-STK1: Vehicle Coverage and Preparation Notes
| Make | Model | Year | Install | CAN | IMMO | BCM | Clutch | I/O Changes |
| DL-SUB9 | Type | Green White/Blue | ||||||
| Subaru | Ascent STD KEY AT | 2019-22 | Type 2 | 40-Pin | B | DSD | N/A | N/A |
| (Canada) |
Covered vehicle use BLADE-AL-SUB9 firmware and the following required accessories, Weblink Hub & ACC RFID1. Flash module, and update the controller firmware. Please follow the directions for RFID programming before attempting to program the BLADE module to the vehicle.
CAN: Type 2 CAN connections are made using the 40-Pin BCM connector and require connecting the white 2-pin female connector to the black male 2-pin connector at marker [D] of the illustration.
Immobilizer: Type B IMMO requires connecting the black and white 2-pin connectors at marker [C] of the illustration.
Lights: Parking lights are pre-wired in the FTI-STK1 harness. Replace the green/white wire of the CM I/O connector with the pre-terminated green/white wire of the harness.
ACC-RFID1 (REQUIRED): SUB9 firmware does not provide immobilizer data, an ACC-RFID1 is therefore required for remote start.
2nd START: The FTI-STK1 harness is pre-wired with a red/white 2nd START output (not required in TYPE 2), cut and insulate the provided wire to prevent short circuits when not used.
I/O Changes: None required
Advisory 1: Program ACC-RFID1 before attempting to program the BLADE module to the vehicle.
Advisory 2: Secure all 2-pin connections, both used and unused, to the main harness body.
FTI-STK1: Installation and Configuration Notes
A. REQUIRED ACCESSORY
B. ADAPTER NOT REQUIRED
C. REQUIRED CONFIGURATION (TYPE B IMMO)
D. REQUIRED CONNECTION
E. NO CONNECTION
FEATURE COVERAGE
| IMMOBILIZER DATA |  |
| ARM OEM ALARM | |
| DISARM OEM ALARM | |
| DOOR LOCK | |
| DOOR UNLOCK | |
| PRIORITY UNLOCK | |
| TRUNK/HATCH RELEASE | |
| TACH OUTPUT | |
| DOOR STATUS | |
| TRUNK STATUS | |
| BRAKE STATUS | |
| E-BRAKE STATUS | |
| A/M ALRM CONTROL FROM OEM REMOTE | |
| A/M RS CONTROL FROM OEM REMOTE | |
| A/M RS CONTROL FROM OEM REMOTE | |
FTI-STK1 – AL-SUB9 – Type 2 2019-22 Subaru Ascent STD KEY AT (CA)
Notice:
LED Programming Error Codes
Module LED flashing RED during programming
1x RED = Unable to communicate with RFID or immobilizer data.
2x RED = No CAN activity. Check the CAN wire connections.
3x RED = No ignition detected. Check the ignition wire connection and CAN.
4x RED = Required ignition output diode not detected.
INSTALL GUIDE
CATRIDGE INSTALLATION
- Slide cartridge into unit. Notice button under LED.
- Ready for Module Programming Procedure.
MODULE PAROGRAMING PROCEDURE
- For this installation, the Weblink HUB is required.
- Remove OEM key 1 from keychain.
Place all other key fobs at least 1 foot away from the Weblink HUB. Failure to comply may result in damage to other key fobs or interfere with the key fob reading process.
- Flash the module using the Weblink HUB. Follow the on screen instructions to complete the key fob reading process.
- WARNING: Do not press the module programming button. Connect power first. Connect module to vehicle.
- Using OEM key 1, turn key to ON position.
- Wait, LED will turn solid BLUE for 2 seconds.
- Turn key to OFF position.
- Module Programming Procedure completed.
WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020
Documents / Resources
 |
FIRSTECH FTI-STK1 Vehicle Coverage [pdf] Instruction Manual FTI-STK1 Vehicle Coverage, FTI-STK1, Vehicle Coverage, Coverage |
