EMERSON Go Canja Makusancin Sensor
Injiniyoyin TopWorx suna farin cikin ba da taimakon fasaha akan samfuran GOTM Switch. Koyaya, alhakin abokin ciniki ne don ƙayyade aminci da dacewa da samfurin a aikace-aikacen su. Har ila yau, alhakin abokin ciniki ne ya shigar da maɓalli ta amfani da lambobin lantarki na yanzu a yankin su.
Tsanaki- Canja Lalacewar
- Dole ne a shigar da sauyawa bisa ga lambobin lantarki na gida.
- Dole ne a sami haɗin wayoyi da kyau.
- Don maɓallan kewayawa biyu, dole ne a haɗa lambobin sadarwa zuwa polarity iri ɗaya don rage yuwuwar gajeriyar layi zuwa layi.
- A cikin damp muhalli, yi amfani da bokan igiyar igiyar igiya ko wani shinge mai kama da danshi don hana ruwa/tashi shiga cibiyar magudanar ruwa.
Hatsari- Amfani mara kyau
Dole ne a shigar da duk masu sauyawa bisa ga buƙatun takaddun shaida.
Tukwici na hawa don daidaitattun maɓalli da latching
- Ƙayyade wurin aiki da ake so.
- Ƙayyade wurin wurin ji akan GO™ Switch.
- Sanya maɓalli da manufa a cikin wani wuri wanda ke tabbatar da manufa ta zo a cikin yankin da ake ji.
In Hoto na 1, An saita manufa don tsayawa a gefen ambulan mai ji. Wannan wani yanayi ne na gefe don aiki mai dogaro na dogon lokaci.
In Hoto 2, an sanya makasudin don tsayawa da kyau a cikin ambulaf mai ji wanda zai tabbatar da aiki mai dorewa.
Maƙasudin ƙarfe yana buƙatar zama aƙalla inci cubic ɗaya a girman. Idan girman girman maƙasudin bai wuce inci cubic ɗaya ba, yana iya rage tasirin aiki sosai ko kuma mai kunnawa ba zai iya gano manufa ba.
In Hoto na 3, Maƙasudin ferrous ya yi ƙanƙanta sosai don a iya gano shi cikin dogaro na dogon lokaci.
In Hoto na 4, Makasudin yana da isasshen girman da taro don aiki mai dogaro na dogon lokaci.
- Ana iya hawa maɓalli a kowane wuri.
Gefe da gefe akan madaidaicin mara ƙarfe (Hoto na 5 da 6).
- Canjawa da aka ɗora akan kayan da ba na maganadisu ba
An ba da shawarar don sakamako mafi kyau
a). A kiyaye duk kayan ƙarfe aƙalla 1” daga canzawa.
b). Karfe da aka sanya a wajen wurin gano maɓalli ba zai shafi aiki ba.
Ba a ba da shawarar cewa an saka maɓalli a kan ƙarfe na ƙarfe ba, saboda raguwar nisa da ake ji.
Kunna/kashe maɓalli
a). Canja tare da daidaitattun lambobin sadarwa - yana da wurin ganewa a gefe ɗaya na maɓalli (A). Don kunnawa, maƙasudin ƙarfe ko maganadisu dole ne su shiga cikin yankin da ake ji (Hoto 7). Don kashe maƙasudin dole ne ya motsa gabaɗaya a wajen wurin da ake ji, daidai ko mafi girma fiye da nisan sake saiti a cikin Tebur.
Don kunna lambobin sadarwa a gefen A (duba Hoto 10), makasudin dole ne ya shigar da cikakken wurin ganowa A na maɓalli (duba kewayon ji a Tebura x). Don kashe lambobin sadarwa a gefen A kuma kunna gefen B, maƙasudin dole ne ya matsa gaba ɗaya a waje da yankin ganewa A da kuma wani makasudin shiga cikakken yankin ji B (Hoto 11). Don sake kunna lambobin sadarwa a gefen A, maƙasudin dole ne ya fita gabaɗaya yankin ganewa B kuma abin da ake nufi dole ne ya sake shigar da yankin ji na A gabaɗaya (Hoto 13).
Rage Rage
Kewayon ji ya haɗa da manufa ta ƙarfe da maganadiso.
Duk na'urorin lantarki da ke da haɗin kai, gami da GO™ Switches, dole ne a goge su daga shigar ruwa ta hanyar tsarin magudanar ruwa. Dubi Figures 14 da 15 don mafi kyawun ayyuka.
Matukar Maɓalli
In Hoto na 14, tsarin magudanar ruwa yana cika da ruwa kuma yana zubewa a cikin maɓalli. A cikin ɗan lokaci, wannan na iya sa canjin ya gaza da wuri.
In Hoto 15, Ƙarshen canjin na iya haɗawa da na'urar shigar da kebul ɗin da aka ba da izini (mai amfani da aka kawo) daidai da umarnin masana'anta don hana kutsewar ruwa wanda ke haifar da gazawar canji da wuri. Hakanan an shigar da madauki mai ɗigo tare da tanadin ruwa don tserewa.
Haɗe-haɗe na Conduit ko Cable
Idan an ɗora maɓalli a kan ɓangaren motsi, tabbatar da cewa magudanar ruwa mai sassauƙa ya daɗe don ba da izinin motsi, kuma a sanya shi don kawar da ɗauri ko ja. (Hoto na 16). A cikin damp aikace-aikace, yi amfani da bokan igiyar igiyar igiya ko wani shinge mai kama da danshi don hana ruwa/samun shigar ruwa. (Hoto na 17).
Bayanin Waya
Dukkanin GO Switches busassun mu'amala ne, ma'ana basu da voltage sauke lokacin da aka rufe, kuma ba su da wani ɗigon ruwa idan an buɗe. Don shigarwa na raka'a da yawa, ana iya haɗa maɓalli a jere ko a layi daya.
GO™ Canja Tsarin Waya
Kasa
Dangane da buƙatun takaddun shaida, ana iya ba da GO Switches tare da ko ba tare da haɗaɗɗiyar waya ta ƙasa ba. Idan aka kawota ba tare da waya ta ƙasa ba, dole ne mai sakawa ya tabbatar da haɗin ƙasa mai kyau zuwa wurin.
Yanayi na Musamman don Tsaron Cikin Gida
- Dukansu lambobin sadarwa na Jifa Biyu da maɓalli daban-daban na Maɓallin Pole Biyu, a cikin maɓalli ɗaya dole ne su zama wani ɓangare na da'irar amintattu iri ɗaya.
- Maɓallan kusanci baya buƙatar haɗi zuwa ƙasa don dalilai na aminci, amma ana samar da haɗin ƙasa wanda ke da alaƙa kai tsaye zuwa shingen ƙarfe. A al'ada, da'ira mai aminci na iya zama ƙasa a wuri ɗaya kawai. Idan ana amfani da haɗin ƙasa, dole ne a yi la'akari da ma'anar wannan a cikin kowane shigarwa. Wato ta hanyar amfani da keɓantaccen keɓantaccen mahalli.
Bambance-bambancen toshe na kayan aiki an sanye su da murfin da ba na ƙarfe ba wanda ya ƙunshi haɗarin lantarki kuma dole ne kawai a tsaftace shi da talla.amp zane. - Dole ne a kawo canjin canji daga ƙwararrun madogarar lafiya ta Ex ia IIC.
- Dole ne a dakatar da jagorar tashi ta hanyar da ta dace da yankin shigarwa.
Tashar Toshe Wayoyin Wuta Don Kariyar Wuta Da Ƙarfafa Tsaro
- Ana iya samun haɗin kai na waje ta hanyar gyare-gyaren hawa. Waɗannan gyare-gyare yakamata su kasance cikin bakin ƙarfe ko madadin ƙarfe mara ƙarfe don rage lalata da tsangwama na maganadisu na aikin sauyawa. Haɗin ya kamata a yi ta hanyar da za a hana sassautawa da karkatarwa (misali tare da murhu/kwayoyi masu siffa da wankin kullewa).
- Za a shigar da na'urorin shigar da kebul masu dacewa daidai da IEC60079-14 kuma dole ne su kula da ƙimar kariya ta shiga (IP) na shingen. Zaren shigar da kebul ɗin ba zai fito a cikin jikin bango ba (watau zai kiyaye izinin zuwa tashoshi).
- Guda guda ɗaya ko madaidaicin madauri na girman 16 zuwa 18 AWG (1.3 zuwa 0.8mm2) shine za'a saukar dashi a kowace tasha. Rufin kowane madubi zai ƙara zuwa tsakanin 1 mm na tashar clampcikin farantin.
Ba a ba da izinin haɗin haɗin gwiwa da/ko ferrules ba.
Waya dole ne ya zama ma'auni 16 zuwa 18 kuma ana ƙididdige nauyin wutar lantarki da aka yiwa alama akan maɓalli tare da zafin sabis na aƙalla 80°C.
Wire tasha sukurori, (4) #8-32X5/16" bakin tare da zobe na shekara, dole ne a ƙarasa zuwa 2.8 Nm [25 lb-in].
Dole ne a matsar da farantin murfin zuwa madaidaicin toshe zuwa ƙimar 1.7 Nm [15lb-in].
Ana iya haɗa GO Switch a matsayin PNP ko NPN dangane da aikace-aikacen da ake so DMD 4 Pin M12 Connector.
Tebur 2: Takaitacciyar FMEA don 10 & 20 Series GO kusancin kusancin maganadisu a cikin yanayi guda (1oo1)
|
Ayyukan Tsaro: |
1. Don rufe lambar sadarwa ta al'ada or
2. To buɗe lambar sadarwa ta al'ada |
||
| Taƙaitaccen IEC 61508-2 Sashe na 7.4.2 da 7.4.4 | 1. Don rufe lambar sadarwa ta al'ada | 2. Don buɗe lambar sadarwar da aka saba | |
| Matsalolin gine-gine & Nau'in samfur A/B | HFT = 0
Nau'in A |
HFT = 0
Nau'in A |
|
| Safe Failure Fraction (SFF) | 29.59% | 62.60% | |
| Rashin gazawar kayan aikin bazuwar [h-1] | DD DU | 0
6.40E-07 |
0
3.4E-07 |
| Rashin gazawar kayan aikin bazuwar [h-1] | DD DU | 0
2.69E-7 |
0
5.59E-7 |
| Ciwon bincike (DC) | 0.0% | 0.0% | |
| PFD @ PTI = 8760 Hrs. MTTR = 24Hs. | 2.82E-03 | 2.82E-03 | |
| Yiwuwar gazawar haɗari
(Babban buƙata - PFH) [h-1] |
6.40E-07 | 6.40E-07 | |
| Hardware aminci mutunci
yarda |
Hanya 1H | Hanya 1H | |
| Yarda da amincin tsari na tsari | Hanyar 1S
Duba rahoton R56A24114B |
Hanyar 1S
Duba rahoton R56A24114B |
|
| Ƙarfin Tsari | SC 3 | SC 3 | |
| An cimma amincin amincin kayan aikin | SILU 1 | SILU 2 | |
DMD 4 Pin M12 Mai Haɗi
Dole ne a yi amfani da ƙasa na waje tare da 120VAC da voltagmafi girma fiye da 60VDC lokacin amfani da haɗin DMD
Sanarwar Amincewa ta EU
Kayayyakin da aka siffanta a nan, sun dace da tanade-tanaden Dokokin Kungiyar masu zuwa, gami da sabbin gyare-gyare:
Ƙananan Voltage Umarnin (2014/35/EU) Umarnin EMD (2014/30/EU) ATEX Umarnin (2014/34/EU).
Matsayin Mutuncin Tsaro (SIL)
Mafi girman ƙarfin SIL: SIL2 (HFT: 0)
Mafi girman iyawar SC: SC3
(HFT:0) Cikakkun Tazarar Gwajin Shekara 1.
Ex da llC T*Ga; Ex ia lllC T*C Da
Yanayin zafin jiki ƙasa da -40 ° C har zuwa 150 ° C akwai don wasu samfuran.
Baseefa 12ATEX0187X
Ex de llC T* Gb; Ex tb lllC T*C Db
Yanayin yanayi ƙasa da -40°C har zuwa 60°C akwai don wasu samfuran.
Baseefa 12ATEX0160X
IECEx BAS 12.0098X 30V AC/DC @ 0.25 NA SPDT SWITCHES
Ziyarci www.topWorx.com don cikakkun bayanai game da kamfaninmu, iyawa, da samfuranmu - gami da lambobi samfurin, takaddun bayanai, ƙayyadaddun bayanai, girma, da takaddun shaida.
info.topworx@emerson.com
www.topWorx.com
OSISI NA GOYON BAYAN DUNIYA
Amurkawa
Hanyar 3300 Fern Valley
Louisville, Kentucky 40213 Amurka
+1 502 969 8000
Turai
Hanyar Horsfield
Bredbury Industrial Estate Stock Port
SK6 2SU
Ƙasar Ingila
+44 0 161 406 5155
info.topworx@emerson.com
Afirka
24 Angus Cescent
Longmeadow Kasuwanci Estate Gabas
Modderfontein
Gauteng
Afirka ta Kudu
27 011 441 3700
info.topworx@emerson.com
Gabas ta Tsakiya
Akwatin gidan waya 17033
Jebel Ali Free Zone
Dubai 17033
Hadaddiyar Daular Larabawa
971 4 811 8283
info.topworx@emerson.com
Asiya-Pacific
1 Pandan Crescent
Singapore 128461
+ 65 6891 7550
info.topworx@emerson.com
© 2013-2016 TopWorx, Duk haƙƙin mallaka. TopWorx™, da GO™ Switch duk alamun kasuwanci ne na TopWorx™. Alamar Emerson alamar kasuwanci ce da alamar sabis na Emerson Electric. Co.
© 2013-2016 Emerson Electric Company. Duk sauran alamomin mallakar masu su ne. Bayani a nan - gami da ƙayyadaddun samfur - ana iya canzawa ba tare da sanarwa ba.
Takardu / Albarkatu
 |
EMERSON Go Canja Makusancin Sensor [pdf] Jagoran Jagora Go Switch Sensor Proximity Sensor, Sensor kusanci, Go Canjawa, Sensor |
