Xlink TCS100 TPMS Sensor
Awọn pato ọja
- Awoṣe: TCS100 Sensor
- Ibamu: Gbogbo agbaye
- Ohun elo: Irin ti ko njepata
- Orisun Agbara: Batiri ṣiṣẹ
- Iwọn Iwọn: 0-100 sipo
Awọn Itọsọna Aabo
Before using the TCS100 Sensor, please read and follow these safety instructions:
- Always wear appropriate protective gear when handling the sensor.
- Avoid exposing the sensor to extreme temperatures or moisture.
- Do not disassemble the sensor yourself; contact a qualified technician for any repairs.
Awọn paramita
The TCS100 Sensor comes with the following parameters.
- Yiye: +/- 2%
- Iwọn Iṣiṣẹ: 0-50°C
- Ipinnu: 0.1 awọn ẹya
Sensor Component Diagram
The diagram below illustrates the components of the TCS100 Sensor for your reference:
Awọn Igbesẹ Isẹ fifi sori ẹrọ
- Igbesẹ 1: Ṣe awọn nozzle nipasẹ awọn hobu ati ki o fix o pẹlu awọn nozzle ojoro nut. Akiyesi pe o ti wa ni ko tightening.
Awọn ilana Lilo ọja
- Ensure the sensor is properly connected to the power source.
- Calibrate the sensor based on your specific measurement requirements.
- Place the sensor in the desired location for accurate readings.
Awọn Itọsọna Aabo
- Jọwọ ka iwe afọwọkọ yii ni pẹkipẹki ṣaaju lilo ọja naa, faramọ ilana ti ọja naa ki o ṣakoso ọna fifi sori ẹrọ ti ọja naa. Ṣaaju fifi sori ẹrọ, jọwọ jẹrisi pe awọn ẹya ẹrọ ọja ti pari, ọja naa le ṣiṣẹ ni deede, ati pe ko si irisi ajeji ati eto. Lakoko ilana fifi sori ẹrọ, ile-iṣẹ naa yoo faramọ awọn pato iṣẹ ṣiṣe itọju ati lo awọn irinṣẹ itọju ọjọgbọn. Bibẹẹkọ, ile-iṣẹ kii yoo ṣe iduro fun awọn iṣoro eyikeyi ti o ṣẹlẹ nipasẹ iṣẹ arufin ti alabara. Ti iṣoro eyikeyi ba wa ninu ilana lilo ọja naa, o gbọdọ paarọ rẹ tabi da duro lẹsẹkẹsẹ ati idanwo nipasẹ oṣiṣẹ itọju alamọdaju tabi iṣẹ lẹhin-tita. Lẹhin fifi ọja sii, rii daju lati tun iwọn iwọntunwọnsi agbara ti taya ọkọ lati yọkuro awọn eewu ailewu.
Awọn paramita
- Awoṣe Ọja: TCS-100
- Ibi ipamọ otutu.-10℃ ~ 50℃
- Iwọn otutu ti nṣiṣẹ:-40℃ ~ 125℃
- Iwọn ibojuwo titẹ:0-900Kpa
- Waterproof grade： IP67
- Igbesi aye batiri:3-5 ọdun
- Ipele Agbara:-33.84d BM
- Igbohunsafẹfẹ:314.9MHz
- Titẹ išedede： ±7Kpa
- Ipeye iwọn otutu:± 3 ℃
- Iwuwo ：26g (pẹlu àtọwọdá)
- Awọn iwọn:to.72.25mm * 44.27mm * 17.63mm
- Atilẹyin ọja: ọdun meji 2
Aworan paati sensọ
Awọn Igbesẹ Isẹ fifi sori ẹrọ
- Igbesẹ 1: Ṣe awọn nozzle nipasẹ awọn hobu ati ki o fix o pẹlu awọn nozzle ojoro nut. Akiyesi pe o ti wa ni ko tightening.
- Igbesẹ 2: Fix awọn sensọ lori awọn air nozzles pẹlu awọn sensọ ojoro dabaru. Ṣe akiyesi pe sensọ yẹ ki o wa nitosi ibudo pẹlu iyipo ti 4N • m.
- Igbesẹ 3: Mu nut nozzle ti afẹfẹ di nut pẹlu wrench lati pari fifi sori ẹrọ. Akiyesi pe wrench nlo iyipo ti 7 N•m.
FCC
Ẹrọ yii ni ibamu pẹlu Apá 15 ti Awọn ofin FCC. Iṣiṣẹ jẹ koko-ọrọ si awọn ipo meji wọnyi:
- Ẹrọ yii le ma fa kikọlu ipalara, ati
- Ẹrọ yii gbọdọ gba kikọlu eyikeyi ti o gba, pẹlu kikọlu ti o le fa isẹ ti ko fẹ.
Eyikeyi iyipada tabi awọn iyipada ti ko fọwọsi ni pato nipasẹ ẹgbẹ ti o ni iduro fun ibamu le sọ aṣẹ olumulo di ofo lati ṣiṣẹ ohun elo naa.
Akiyesi: This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient tabi tun eriali gbigba pada.
- Mu iyatọ pọ si laarin ẹrọ ati olugba.
- So ẹrọ pọ si ohun iṣan lori kan Circuit yatọ si lati eyi ti awọn olugba ti a ti sopọ.
- Kan si alagbawo oniṣowo tabi redio ti o ni iriri / onimọ-ẹrọ TV fun iranlọwọ.
Awọn ibeere Nigbagbogbo
- Q: How often should I calibrate the TCS100 Sensor?
- A: It is recommended to calibrate the sensor every three months for optimal performance.
- Q: Njẹ sensọ le ṣee lo ni awọn agbegbe ita gbangba?
- A: The sensor is designed for indoor use; avoid exposing it to outdoor conditions to prevent damage.
Awọn iwe aṣẹ / Awọn orisun
 |
Xlink TCS100 TPMS Sensor [pdf] Awọn ilana TCS100, TCS100 TPMS Sensor, TPMS Sensor, Sensor |