Vula isiLawuli soBubushushu beSakhelo seSiteti esiBili
Incwadi Yemiyalelo
Le ncwadana imfutshane yenzelwe ireferensi ekhawulezayo kuqhagamshelo lweingcingo kunye nokukhangela iparameter. Ukufumana iinkcukacha ezithe vetshe malunga nokusebenza kunye nesicelo; nceda ungene ku www.ppiindia.net
IGALELO / IPHUMELO IMIGAQO YOQINISEKISO
| Iiparamitha |
Iisetingi (Ixabiso eliMiselweyo) |
Uhlobo Longeniso |
Jonga kwiTheyibhile yoku-1 (Okuhlala kukho : Uhlobo K) |
Control Logic  |
 Buyela umva ngqo (Okuhlala kukho :Umva) |
Beka indawo ePhantsi  |
Min. Uluhlu ukuya kwiNdawo ePhakamileyo yohlobo lweNgeniso ekhethiweyo (Okumiselweyo : Umz. Uluhlu lwe ) Uhlobo loGalelo oluKhethiweyo |
I-Setpoint High  |
Misela uPhantsi ukuya kwizembe. Uluhlu lweM lodidi lweNgeniso olukhethiweyo ( Okwendalo : Ubuninzi. Uluhlu lwegalelo eliKhethiweyo ) Udidi lweNgeniso olukhethiweyo |
I-Offset yePV  |
-1999 ukuya ku-9999 okanye -199.9 ukuya ku-999.9 (Okumiselweyo: 0) |
Isihluzi seDijithali sePV |
0.5 ukuya 25.0 Imizuzwana (ngamanyathelo 0.5 Seconds) (Okuhlala kukho : 1.0) |
Lawula isiPhumo seNdlela |
 Udluliselo (Okumiselweyo) SSR |
Isiphumo-2 soKhetho loMsebenzi |
 (Okumiselweyo) Akukho Alarm Controller Soak Start Output |
| Imveliso 2 Uhlobo |
Udluliselo (Okumiselweyo) SSR |
IMIDA YOLAWULO
| Iiparamitha |
Iisetingi (Ixabiso eliMiselweyo) |
Imo Yokulawula  |
 (Okuhlala kukho) On-Off PID |
On-Off Hysteresis  |
1 ukuya ku-999 okanye 0.1 ukuya ku-99.9 (Okumiselweyo: 2 okanye 0.2) |
Ukulibaziseka kwexesha leCompressor  |
0 ukuya 600 Sec. (ngamanyathelo ka-0.5 Sec.) (Okuhlala kukho: 0) |
Ixesha lomjikelo  |
0.5 ukuya 120.0 Imizuzwana (ngamanyathelo 0.5 Seconds) (Okuhlala kukho : 20.0 Sec) |
Ibakala leProportional  |
0.1 ukuya 999.9 (Okuhlala kukho: 10.0) |
Ixesha elidibeneyo  |
0 ukuya 1000 Imizuzwana (Okuhlala kukho: 100 Sec) |
Ixesha eliphumayo  |
0 ukuya 250 Imizuzwana (Okuhlala kukho: 25 Sec) |
ISIPHUMO-2 IIPARAMETHA ZOMSEBENZI
OP2 Umsebenzi : Ialam
| Iiparamitha |
Iisetingi (Ixabiso eliMiselweyo) |
Uhlobo lweAlarm  |
 Inkqubo ePhantsi Ibhendi yefestile etenxileyo ePhezulu Ukuphela kweNqana (Ehlala ikho : Inkqubo iPhantsi) |
I-Alarm Inhibit  |
 Ewe Hayi (Okuhlala kukho: Ewe) |
I-Alarm Logic  |
 Ukubuyela umva okuqhelekileyo (Okumiselweyo : Kwesiqhelo) |
Isivusi maxesha  |
5 ukuya 250 (Okuhlala kukho: 10) |
Umsebenzi we-OP2 : Ulawulo
| Iiparamitha |
Iisetingi (Ixabiso eliMiselweyo) |
I-Hysteresis  |
1 ukuya ku-999 okanye 0.1 ukuya ku-99.9 (Okumiselweyo: 2 okanye 0.2) |
Control Logic  |
 Ukubuyela umva okuqhelekileyo (Okumiselweyo : Kwesiqhelo) |
OP2 Umsebenzi : Iblower
| Iiparamitha |
Iisetingi (Ixabiso eliMiselweyo) |
I-Blower / Compressor Hysteresis  |
1 ukuya ku-250 okanye 0.1 ukuya ku-25.0 (Okumiselweyo: 2 okanye 0.2) |
Ukulibaziseka kweBlower / Compressor Time  |
0 ukuya 600 Sec. (ngamanyathelo ka-0.5 Sec.) (Okuhlala kukho: 0) |
IMIGAQO YOLAWULO
| Iiparamitha |
Iisetingi (Ixabiso eliMiselweyo) |
Uzicule Umyalelo  |
Ewe Hayi (Okuhlala kukho: Hayi)  |
I-Overshoot Inhibit Yenza / Khubaza  |
Khubaza ukuVumela (Okuhlala kukho : Khubaza)  |
I-Overshoot Inhibit Factor  |
(Okuhlala kukho: 1.2) 1.0 ukuya ku-2.0 |
IMvume yokuHlelwa kwendawo kwiPhepha loMsebenzisi  |
Khubaza ukwenza (Okuhlala kukho : Yenza)  |
Lungisa Umyalelo wokuLahla kwiPhepha loMsebenzisi  |
Khubaza ukwenza (Okuhlala kukho : Yenza) |
Soak uhlengahlengiso lwexesha kwiPhepha loMsebenzisi  |
Khubaza ukwenza (Okuhlala kukho : Yenza) |
IIPARAMETHA ZOMSEBENZI
OP2 Umsebenzi : Ialam
| Iiparamitha x |
Iisetingi (Ixabiso eliMiselweyo) |
Soak Start Command  |
 Hayi Ewe (Okuhlala kukho: Hayi) |
| Gxila uLahla umyalelo |
Hayi Ewe (Okuhlala kukho: Hayi) |
Ixesha lokuphumla  |
00.05 ukuya ku-60.00 M:S okanye 00.05 ukuya ku-99.55 H:M okanye 1 ukuya ku-999 Iiyure (Okuhlala kukho: 3 okanye 0.3) |
I-Alarm Setpoint  |
Ubuncinane ukuya kobona Bukhulu Uluhlu olukhankanyiweyo kuHlobo lweNgeniso olukhethiweyo (Okuhlala kukho : 0) |
| Iiparamitha |
Iisetingi (Ixabiso eliMiselweyo) |
Ukutenxa kweAlarm  |
-1999 ukuya ku-9999 okanye -199.9 ukuya ku-999.9 (Okumiselweyo: 3 okanye 0.3) |
I-Alarm Band  |
3 ukuya ku-999 okanye 0.3 ukuya ku-99.9 (Okumiselweyo: 3 okanye 0.3) |
Umsebenzi we-OP2 : Ulawulo
| Iiparamitha |
Iisetingi (Ixabiso eliMiselweyo) |
Indawo yoLawulo oluNcedisayo  |
(Uluhlu oluncinci – SP) ukuya (Ubukhulu. Uluhlu – SP) (Okumiselweyo: 0) |
OP2 Umsebenzi : Iblower
| Iiparamitha |
Iisetingi (Ixabiso eliMiselweyo) |
Indawo yolawulo lokuvuthela  |
0.0 ukuya 25.0 (Okuhlala kukho: 0) |
Indawo yolawulo lweSeti (SP) yokutshixa
| Iiparamitha |
Iisetingi (Ixabiso eliMiselweyo) |
Indawo yokutshixa  |
Ewe Hayi (Okuhlala kukho: Hayi) |
NYONGA IIPARAMETHA ZESIXEKO
| Iiparamitha |
Iisetingi (Ixabiso eliMiselweyo) |
Vuselela isibali-xesha  |
 Hayi Ewe (Okuhlala kukho: Hayi) |
IiYunithi zeXesha  |
 Iiyure zikaManse: Iiyure eziMzu (Okumiselweyo : uMzu: uMzuzo) |
Ixesha lokuphumla  |
00.05 ukuya 60:00 Manse 00.05 ukuya 99:55 Hrs: Min 1 ukuya 999 Iiyure (Okumiselweyo: 00.10 Manse) |
Soak qala iBand  |
0 ukuya ku-9999 okanye 0.0 ukuya ku-999.9 (Okumiselweyo: 5 okanye 0.5) |
Isicwangciso sokubamba  |
 Akukho NONE |
| Iiparamitha |
Iisetingi (Ixabiso eliMiselweyo) |
Bamba ibhanti  |
1 ukuya ku-9999 okanye 0.1 ukuya ku-999.9 (Okumiselweyo: 5 okanye 0.5) |
Ukucinywa kweSiphumo soLawulo kwiSiphelo sexesha  |
 Hayi Ewe (Okuhlala kukho: Hayi) |
Indlela yokuBuyisa ukusilela kwamandla  |
 Qhubeka (Re)Qalisa Ukulahla (Okuhlala kukho : Qhubeka) |
| Ukhetho |
Ithetha ukuthini |
Uluhlu (Ubuncinci ukuya kuMax.) |
Isigqibo |
 |
Uhlobo lwe-J Thermocouple |
0 ukuya +960°C |
1 |
 |
Uhlobo lwe-Thermocouple |
-200 ukuya +1375°C |
1 |
 |
3-wire, RTD PT100 |
-199 ukuya +600°C |
1 |
 |
3-wire, RTD PT100 – |
-199.9 ukuya +600.0°C |
0.1 |
IPHANSI LANGAPHAMBILI
Ibhodi yokubonisa
Inguqulelo encinci yokuBonisa
0.39” ubude, 4 Digit, Umqolo oPhezulu
0.39” ubude, 4 Digit, Umqolo ongezantsi
Inguqulelo enkulu yokuBonisa
0.80” ubude, 4 Digit, Umqolo oPhezulu
0.56” ubude, 4 Digit, Umqolo ongezantsi
IBhodi yoLawulo
Uyilo
Keys Operation
| Uphawu |
Isitshixo |
Umsebenzi |
 |
IPHEPHA |
Cofa ukungena okanye ukuphuma kwimo yokuseta. |
 |
PHANTSI |
Cinezela ukunciphisa ixabiso leparameter. ukubamba ucinezele isantya phezulu utshintsho. |
 |
UP |
Cinezela ukwandisa ixabiso leparameter. ukubamba ucinezele isantya phezulu utshintsho. |
 |
NGENA |
Cinezela ukugcina ixabiso lepharamitha emiselweyo kunye nokuskrola
ukuya kwiparameter elandelayo kwi PAGE. |
PV Imposiso Iimpawu
| Umyalezo |
Uhlobo lwemposiso yePV |
 |
Uluhlu olungaphezulu (PV ngaphezulu koMax. Uluhlu) |
 |
Ngaphantsi koluhlu (PV ngaphantsi koluhlu oluncinci) |
 |
Vula (iThermocouple / RTD yaphukile) |
UKUQHAGAMSHELWA KOMbane
101, Diamond Industrial Estate, Namghar,
Indlela yaseVasai (E), kwiSithili. Palghar – 401 210.
Iintengiso : 8208199048 / 8208141446
Inkxaso : 07498799226 / 08767395333
E: sales@ppiindia.net,
support@ppiindia.net
Amaxwebhu / Izibonelelo
Iimbekiselo
