Vhura Frame Dual Set Point Temperature Controller
Bhuku reMirayiridzo
Iri bhuku ripfupi rinonyanya kuitirwa kukurumidza kutaridza kune wiring connections uye parameter kutsvaga. Kuti uwane mamwe mashoko pamusoro pekushanda uye kushandiswa; ndapota pinda pa www.ppiindia.net
INPUT / OUTPUT CONFIGURATION PARAMETERS
| Parameters |
Settings (Default Value) |
Input Type |
Refer Tafura 1 (Default: Type K) |
Kudzora Logic  |
 Reverse Direct (Default: Reverse) |
Setpoint Low  |
Min. Range kusvika kuSetPoint Yepamusoro kune yakasarudzwa Yekupinza mhando (Default: Min. Range yeiyo ) Yakasarudzwa Rudzi rweKupinza |
Setpoint High  |
Setpoint Low to demo. Range M yemhando yakasarudzwa yeInput (Default : Max. Range yezvasarudzwa) Rudzi rweKupinza rwakasarudzwa |
Offset yePV  |
-1999 kusvika 9999 kana -199.9 kusvika 999.9 (Default: 0) |
Digital Sefa YePV |
0.5 kusvika 25.0 Sekondi (mumatanho e0.5 Seconds) (Default : 1.0) |
Control Output Type |
 Relay (Default) SSR |
Output-2 Basa Sarudzo |
 (Default) Hapana Alarm Control Blower Soak Kutanga Kubuda |
| Output 2 Type |
Relay (Default) SSR |
KUDZORA PARAMETERA
| Parameters |
Settings (Default Value) |
Kudzora Mode  |
 (Default) On-Off PID |
On-Off Hysteresis  |
1 kusvika 999 kana 0.1 kusvika 99.9 (Default: 2 kana 0.2) |
Compressor Nguva Kunonoka  |
0 kusvika 600 Sec. (mumatanho e0.5 Sec.) (Default : 0) |
Cycle Time  |
0.5 kusvika 120.0 Sekondi (mumatanho e0.5 Sekondi) (Default : 20.0 Sec) |
Proportional Bhendi  |
0.1 kusvika 999.9 (Default: 10.0) |
Integral Time  |
0 kusvika 1000 Sekondi (Default: 100 Sec) |
Derivative Time  |
0 kusvika 250 Sekondi (Default: 25 Sec) |
OUTPUT-2 BASA PARAMETERS
OP2 Basa: Alamu
| Parameters |
Settings (Default Value) |
Alarm Type  |
 Maitiro Yakaderera Maitiro Yakakwirira Kutsauka Band Window Band End of Soak (Default: Maitiro Yakaderera) |
Alarm Inhibit  |
 Hongu Kwete (Default: Hongu) |
Alarm Logic  |
 Zvakajairika Reverse (Default: Zvakajairwa) |
Alarm Nguva  |
5 kusvika 250 (Default: 10) |
OP2 Basa: Kudzora
| Parameters |
Settings (Default Value) |
Hysteresis  |
1 kusvika 999 kana 0.1 kusvika 99.9 (Default: 2 kana 0.2) |
Kudzora Logic  |
 Zvakajairika Reverse (Default: Zvakajairwa) |
OP2 Basa: Blower
| Parameters |
Settings (Default Value) |
Blower / Compressor Hysteresis  |
1 kusvika 250 kana 0.1 kusvika 25.0 (Default: 2 kana 0.2) |
Blower / Compressor Nguva Kunonoka  |
0 kusvika 600 Sec. (mumatanho e0.5 Sec.) (Default : 0) |
SUPERVISORY PARAMETERS
| Parameters |
Settings (Default Value) |
Self-tune Command  |
Hongu Kwete (Default: Kwete)  |
Overshoot Inhibit Gonesa / Dzima  |
Dzima Kugonesa (Default: Disable)  |
Overshoot Inhibit Factor  |
(Default: 1.2) 1.0 kusvika 2.0 |
Setpoint Kugadzirisa Mvumo pane Operator Peji  |
Dzima Kugonesa (Default: Enesa)  |
Soak Abort Command pane Operator Peji  |
Dzima Kugonesa (Default: Enesa) |
Soak Nguva Yekugadzirisa pane Operator Peji  |
Dzima Kugonesa (Default: Enesa) |
OPERATOR PARAMETERS
OP2 Basa: Alamu
| Parameters x |
Settings (Default Value) |
Soak Start Command  |
 Kwete Hongu (Default: Kwete) |
| Soak Abort Command |
Kwete Hongu (Default: Kwete) |
Soak Time  |
00.05 kusvika 60.00 M:S kana 00.05 kusvika 99.55 H:M kana 1 kusvika 999 Maawa (Default : 3 kana 0.3) |
Alarm Setpoint  |
Minimum to Maximum Range yakatsanangurwa kune yakasarudzwa Rudzi rweKupinza (Default : 0) |
| Parameters |
Settings (Default Value) |
Alarm Kutsauka  |
-1999 kusvika 9999 kana -199.9 kusvika 999.9 (Default: 3 kana 0.3) |
Alarm Band  |
3 kusvika 999 kana 0.3 kusvika 99.9 (Default: 3 kana 0.3) |
OP2 Basa: Kudzora
| Parameters |
Settings (Default Value) |
Mubatsiri Kudzora Setpoint  |
(Min. Range – SP) kusvika (Max. Range – SP) (Default : 0) |
OP2 Basa: Blower
| Parameters |
Settings (Default Value) |
Blower Control Setpoint  |
0.0 kusvika 25.0 (Default: 0) |
Kudzora Setpoint (SP) Kukiya
| Parameters |
Settings (Default Value) |
Setpoint Locking  |
Hongu Kwete (Default: Kwete) |
SOAK TIMER PARAMETERS
| Parameters |
Settings (Default Value) |
Soak Timer Inogonesa  |
 Kwete Hongu (Default: Kwete) |
Nguva Units  |
 Manse Maawa: Maminitsi Maawa (Default : Min: Sec) |
Soak Time  |
00.05 kusvika 60:00 Manse 00.05 kusvika 99:55 Hrs: Min 1 kusvika 999 Maawa (Default : 00.10 Manse) |
Soak kutanga Band  |
0 kusvika 9999 kana 0.0 kusvika 999.9 (Default: 5 kana 0.5) |
Holdback Strategy  |
 Hapana Pazasi Paviri (Default: Hapana) |
| Parameters |
Settings (Default Value) |
Bata Band  |
1 kusvika 9999 kana 0.1 kusvika 999.9 (Default: 5 kana 0.5) |
Kudzima Kudzora Kubuda PaTimer End  |
 Kwete Hongu (Default: Kwete) |
Simba-kutadza Recovery Method  |
 Ramba (Re) Tanga Kubvisa (Default: Ramba) |
| Option |
Zvazvinoreva |
Range (Min. kusvika Max.) |
Resolution |
 |
Nyora J Thermocouple |
0 kusvika+960°C |
1 |
 |
Tora K Thermocouple |
-200 kusvika +1375°C |
1 |
 |
3-waya, RTD PT100 |
-199 kusvika +600°C |
1 |
 |
3-waya, RTD PT100 - |
-199.9 kusvika +600.0°C |
0.1 |
KUMASHURE PANEL LAYOUT
Ratidza Bhodhi
Diki Ratidza Version
0.39” kureba, 4 Digit, Upper Row
0.39” kureba, 4 Digit, Lower Row
Yakakura Display Version
0.80” kureba, 4 Digit, Upper Row
0.56” kureba, 4 Digit, Lower Row
Control Board
Layout
Keys Operation
| Symbol |
Key |
Function |
 |
PEJI |
Dzvanya kuti upinde kana kubuda mumodhi yekuseta. |
 |
PASI |
Dzvanya kuti uderedze kukosha kweparameter Kudzvanya kamwe kunoderedza kukosha nekuverenga kumwe; kubata wakadzvanywa kunomhanyisa shanduko. |
 |
UP |
Dzvanya kuti uwedzere parameter kukosha Kudzvanya kamwe kunowedzera kukosha nekuverenga kumwe; kubata wakadzvanywa kunomhanyisa shanduko. |
 |
PINDA |
Dzvanya kuchengetedza iyo yakatarwa parameter kukosha uye kupuruzira
kune inotevera parameter paPAGE. |
PV Kukanganisa Zviratidzo
| Mharidzo |
PV Error Type |
 |
Over-range (PV pamusoro peMax. Range) |
 |
Under-range (PV pazasi Min. Range) |
 |
Vhura (Thermocouple / RTD yakaputsika) |
KUKUNGAMIRIRA KWEMAGETSI
101, Diamond Industrial Estate, Namghar,
Vasai Road (E), Dist. Palghar - 401 210.
Sales : 8208199048 / 8208141446
Support : 07498799226 / 08767395333
E: sales@ppiindia.net,
support@ppiindia.net
Zvinyorwa / Zvishandiso
References
