RKI LITŠOANTŠISO T3A Sensor Transmitter

Litlhaloso

• Setšoantšo sa T3A
• Nomoro ea karolo: 71-0533
• Phetolelo: P15
• E lokollotsoe: 7/15/24
• Moetsi: RKI Instruments, Inc.
• Websebaka: www.rkiinstruments.com

Sehlahisoa se Felletseview

The RKI Instruments Inc. T3A ke ambient air Hazardous gas sensor assembly e etselitsoeng ho shebella likhase tse haufi le sebaka sa sensor housing. Ho bohlokoa ho etsa phuputso ea sebaka sa marang-rang ho fumana sebaka se nepahetseng le palo ea li-sensor tsa li-sensor ho thibela ho lutla ha khase ho sa bonahaleng ho ka lebisang ho tsoa likotsi kapa tahlehelo ea bophelo.

Tlhaloso ea Kantle

Tlhaloso ea kantle ea T3A e kenyelletsa tlhahisoleseling mabapi le ponahalo ea 'mele, likhokahano le likhokahano tsa kopano ea sensor. Karolo ena e fana ka lintlha tsa mokhoa oa ho khetholla le ho sebelisana le likarolo tse ka ntle tsa sesebelisoa.

Tlhaloso ea ka hare

Tlhaloso ea ka hare ea T3A e fana ka leseli ka likarolo tsa ka hare, potoloho le mekhoa ea kopano ea sensor. Ho utloisisa ts'ebetso ea kahare ea sesebelisoa ho bohlokoa bakeng sa ho rarolla mathata le merero ea tlhokomelo.

Ho kenya

Ho kenya ts'ebetso e nepahetseng ea kopano ea sensor ea T3A ho bohlokoa bakeng sa ts'ebetso ea eona e sebetsang. Ke basebetsi ba tšoanelehang feela ba lokelang ho sebetsana le ts'ebetso ea ho kenya. Hoa hlokahala ho sheba bukana ea litaelo ka botlalo pele u qala mokhoa oa ho kenya ho netefatsa polokeho le ts'ebetso e nepahetseng.

Litaelo tsa Tšebeliso ea Sehlahisoa

1. Boitokisetso: Etsa bonnete ba hore sebaka seo ha se na likhase tse tukang mollo pele u lekanya kapa u sebeletsa.
2. Kemiso: Latela litaelo tse qaqileng tsa ho instola tse fanoeng bukeng ea tataiso. Sebelisa litiiso tsa conduit ka har'a lisenthimithara tse 18 tsa lebota le kampetsoeng ho latela litekanyetso tse kotsi tsa sebaka.
3. Ts'ebetso: Kamora ho kenya, kenya matla sesebelisoa ho latela litaelo. Ela hloko ho baloa le ho hlahloba khafetsa ho bona ho na le lintho tse sa tloaelehang.
4. Tlhokomelo: Kemiso ea tlhokomelo ea kamehla ho latela litataiso tse fanoeng. Boloka kopano ea sensor e hloekile 'me e se na litšitiso bakeng sa ho bala ho nepahetseng.

FAQs

P: Ke lokela ho etsa eng haeba ke kopana le khase e sa bonahaleng dutla?
A: Haeba u belaella ho lutla ha khase, tsoa sebakeng seo hang-hang 'me u ikopanye le basebetsi ba tšoanelehang bakeng sa thuso. U se ke ua leka ho lokisa bothata ka bouena.

P: Kopano ea sensor e lokela ho lekanngoa hangata hakae?
A: Maqhubu a calibration a ka fapana ho latela ts'ebeliso le maemo a tikoloho. Sheba buka ea mosebelisi bakeng sa likhothaletso tse khethehileng tsa calibration.

P: Na nka kenya likopano tse ling tsa sensor ntle le sebaka sa marang-rang lipatlisiso?
A: Ho khothaletsoa ka matla ho etsa phuputso ea sebaka pele u kenya li-sensor tsa tlatsetso ho netefatsa bokhoni bo nepahetseng ba tšireletso le ho lemoha.

"`

Buka ea Opereishene
Nomoro ea Karolo: 71-0533 Phetoho: P15
E lokollotsoe: 7/15/24 RKI Instruments, Inc. www.rkiinstruments.com

TLHOKOMELO
Bala 'me u utloisise bukana ena ea litaelo pele u sebelisa mochine. Tšebeliso e sa nepahalang ea detector e ka baka kotsi ea 'mele kapa lefu. Ho lekanya nako le nako le tlhokomelo ea detector ho bohlokoa bakeng sa ts'ebetso e nepahetseng le ho bala ka nepo. Ka kopo, lekanya 'me u boloke sebui sena khafetsa! Khafetsa ea calibration e ipapisitse le mofuta oa ts'ebeliso eo u nang le eona le mefuta ea sensor. Bakeng sa lits'ebetso tse ngata, maqhubu a tloaelehileng a calibration a pakeng tsa likhoeli tse 3 le tse 6 empa hangata kapa ka tlase ho latela ts'ebeliso ea hau.
2 · Bukana ea Opereishene ea T3A

Tiisetso ea Sehlahisoa
RKI Instruments, Inc. e fana ka tumello ea hore thepa ea alamo ea khase e rekisitsoeng ke rona e se ke ea e-ba le mefokolo ea thepa, moetso, le ts'ebetsong nako ea selemo ho tloha letsatsing leo e rometsoeng ka lona ho tloha RKI Instruments, Inc. Likarolo leha e le life tse fumanoang li le phoso nakong eo li tla lokisoa. kapa ho nkeloa sebaka, ka khetho ea rona, mahala. Tiisetso ena ha e sebetse ho lintho tseo ka tlhaho ea tsona li ka senyehang kapa ho sebelisoa litšebeletsong tse tloaelehileng, 'me li tlameha ho hloekisoa, ho lokisoa kapa ho nkeloa sebaka ka tsela e tloaelehileng. Examplikarolo tse joalo ke tsena:

· Li-cartridges tse monyang · Li-Fuse · Li-diaphragm le li-valve tsa Pump · Libetri · Likarolo tsa Sefe Tiisetso e hlakoloa ke tlhekefetso e kenyelletsang tšenyo ea mochini, ho fetoloa, ho ts'oaroa ka tsela e mpe, kapa mekhoa ea tokiso e sa tsamaellanang le buka ea opareitara. Tiisetso ena e bontsha boholo ba melato ya rona, mme ha re ikarabelle bakeng sa ditjeho tsa ho tlosa kapa ho tjhesa, ditjeho tsa tokiso ya lehae, ditjeho tsa dipalangwang, kapa ditjeho tse sa lebellwang tse bileng teng ntle le tumello ya rona pele.
TIISETSO ENA E BONAHALA MAHALA A LITIISETSO TSOHLE LE TSE LING TSOHLE, TSE HLAHANG KAPA TSE HLAHANG, LE LITLAMOHO TSOHLE TSE LING KAPA LITLHAKISO TSA RKI INSTRUMENTS, HO kenyeletsoa EMPA E SA LENYETSOE HO, MOKHATLO OA MOSEBETSI OA MOLAO OSE. HA HO LE TSATSI, RKI INSTRUMENTS, INC. E TLA BA MOTHO OA TSOHLE, KA TSATSAHALO, KAPA.
TAHLEHELO KAPA TŠENYETSO EA MOFUTA OFE KA FE kapa O Mong o amanang le tšebeliso ea oona.

LIHLAHISO KAPA HO HLOLEHA HA LIHLAHISO TSA LONA HO SEBETSA KAPA HO SEBETSA KA NTLE. Tiisetso ena e akaretsa lisebelisoa le likarolo tse rekisetsoang basebelisi ke barekisi ba lumelletsoeng, barekisi le baemeli joalo ka ha ba khethiloe ke RKI Instruments, Inc. Ha re nahane hore re tla lefshoa bakeng sa kotsi leha e le efe kapa tšenyo e bakiloeng ke ts'ebetso ea mochine ona oa khase, 'me tiisetso ea rona e lekanyelitsoe ho fetola likarolo kapa thepa ea rona e feletseng.
Buka ea Opereishene ea T3A · 3

Lipolelo tsa Temoso
TEMOSO: TLHOKOMELISO - KOTSI EA HO KHOHLOA - HO FUMANA KA MALOKAHA HO KA HAETSA MOSEBETSI OA MOFUTA OA I, KAROLO EA 1, kapa se lekanang joalo ka ha ho boletsoe bukeng ea mosebelisi.
AVERTISSEMENT – RISQUE D'EXPLOSION-LA SUBSTITUTION DE COMPOSANTS PEUT RENDURE CE MATERIEL INACCEPTABLE POUR LES EMPLACEMENTS DE CLASSE I, DIVISION I.
TLHOKOMELISO: Bakeng sa mabaka a polokeho, thepa ena e tlameha ho sebetsoa le ho sebetsoa ke basebetsi ba nang le litsebo feela. Bala le ho utloisisa bukana ea litaelo ka botlalo pele u sebetsa kapa u sebeletsa.
TLHOKOMELISO: TŠELA DES RAISONS DE SECURITE, CET ÉQUIPEMENT DOIT ETRE SEBELISA ENTRETENU ET REPARER UNIQUEMENT PAR UN PERSONNEL QUALIFIE. ETUDIER LE MANUEL D' DITAELO EN ENTER AVANT D' UTILISER, D' ENTERETENIR OU DE RÉPARER L' ÉQUIPEMENT.

TLHOKOMELISO: SEBAKA ENA E TLAMEHA HO HLOKA LIKHASE TSE TENG KA NAKO EA KALIBRATION.
TLHOKOMELISO: CETTE ZONE DOIT ETRE EXEMPTE DE GAZ INFLAMMABLES PENDANT L'ETALONNAGE.
TLHOKOMELISO: HO THIBELA HO TŠOA HA SEEMO SA SEBAKA SA HO PHAHLOKA, tlosa seqhomaneng PELE U SEBELISA.
TLHOKOMELISO: Setiiso sa conduit se tlameha ho sebelisoa ka har'a lisenthimithara tse 18 tsa lebota le kampetsoeng ho lumellana le boemo bo kotsi ba sebaka sa sehlahisoa sena.

Fetileview
The RKI Instruments, Inc. T3A e thibelang ho phatloha ha khase e kotsi moeeng e etselitsoe ho bona mefuta e mengata ea likhase tse chefo libakeng tse ka bang kotsi. Sehlahisoa sena ke QPS e netefalitsoeng e le Sehlopha sa I, Karolo ea 1, Lihlopha tsa B, C, le D mme e fuoe lintlha bakeng sa Zone 1, Sehlopha sa IIB. T3A e na le li-switches tsa makenete tse sa keneng tse lumellang ho hlophisoa ha sistimi ka botlalo, ho lekanya khafetsa, le ho lokisoa ha sehlahisoa ho etsoa tšimong, ntle le ho bula sebaka se koaletsoeng le ho roba tiiso ea sebaka se koaletsoeng, ka hona ho beha tekanyo ea bopaki ba ho phatloha ha sesebelisoa. Sebopeho se sa tsitsang se nang le T3A se khoneha ka tšebeliso ea sesebelisoa sa makenete se kenyelletsoeng ho rekoa ha sesebelisoa.
Bukeng ena, litaelo li bua ka tšebeliso ea li-push-buttons, tse ka lehlakoreng le ka pele la sesebelisoa. Libakeng tse ling, ts'ebetso ea li-switches tsa makenete tse sa keneng, ka tšebeliso ea sesebelisoa sa makenete, e tla nkela sebaka sa taelo ea liketso tsa konopo ea konopo. Ho sebelisa sesebelisoa sa makenete, tšoara sesebelisoa lehlakoreng la konokono ea sesebelisoa haufi le konopo eo u lakatsang ho e kenya. Ha sesebelisoa sa makenete se fetoloa, ho tla hlaha sesupo se hlahang skrineng, se bolelang hore ho entsoe khokahano.

Sesepa sa pontšo sa T3A se tla lula se bonts'a bongata ba khase bo bonoang ke kopano ea sensor.
Tokomane ena ke buka ea ts'ebetso e nang le litšoantšo le litaelo tsa mohato ka mohato bakeng sa ho kenya ts'ebetso e nepahetseng le e sireletsehileng, ho qala, ho hlophisa, ho sebetsa ka mokhoa o tloaelehileng, le tlhokomelo ea lihlahisoa tsa T3A.
ELA HLOKO: Tokomane ena e lokela ho baloa ka botlalo pele ho ts'ebetso ea pele ea sehlahisoa.

Buka ea Ts'ebetso ea T3A

Fetileview · 7

Litlhaloso

Lethathamo la 1 le thathamisa lintlha tsa T3A.
Lethathamo la 1: Litlhaloso

Khase e Lebeletsoeng
Ammonia (NH3)

Sebaka sa ho Khetholla
0-100 ppm 0-200 ppm

Keketso
1 ppm

0-300 ppm

0-500 ppm

0-1,000 ppm

Arsine (AsH3) Carbon Dioxide (CO2)

0-1.00 ppm 0-5,000 ppm 0-5.0% molumo

0.01 ppm 1 ppm 0.1%.

Carbon monoxide (CO)

0-500 ppm

1 ppm

0-1,000 ppm

Chlorine (Cl2) Chlorine Dioxide (ClO2)

0-10.0 ppm 0-1.00 ppm 0-5.00 ppm

0.1 ppm 0.01 ppm

Khase e tukang

0-100% LEL

1% LEL

0-100% molumo

1% ea molumo

Ethylene oxide (EtO)

0-10.00 ppm

0.01 ppm

Formaldehyde (CH2O) Hydrogen (H2) Hydrogen Chloride (HCl)

0-10.00 ppm 0-100% LEL 0-20 ppm

1% LEL 1 ppm

0-30 ppm

0-100 ppm

Hydrogen Cyanide (HCN)

0-50 ppm

Hydrogen Fluoride (HF)

0-10.0 ppm

0.1 ppm

Hydrogen Sulfide (H2S)

0-10.0 ppm 0-25 ppm

1 ppm

0-50 ppm

0-100 ppm

0-500 ppm

0-2,000 ppm

Nitric oxide (NO)

0-250 ppm

Nitrogen Dioxide (NO2)

0-20 ppm

Haze. Sebaka.
Cl. 1 Div. 2
Cl. 1 Div. 1
Cl. 1 Div. 2 Cl. 1 Div. 1 Cl. 1 Div. 2 Cl. 1 Div. 1 Cl. 1 Div. 2 Cl. 1 Div. 1 Cl. 1 Div. 2 Cl. 1 Div. 1
Cl. 1 Div. 2

8 · Litlhaloso

Buka ea Ts'ebetso ea T3A

Khase e Lebeletsoeng
Oxygen (O2) Ozone (O3)
Phosphine (PH3) Sulfur Dioxide (SO2)
Sampling Mokhoa oa Zero Suppression
Kakaretso Ratings
Lebokose la Junction Setifikeiti sa Sebaka se Kotsi
Setifikeiti sa Sebaka se Kotsi sa Sensor Housing
Tshebetso Voltage Current Drw Operating Temperature Range Humidity Range Signal Output
Relay Contact Ratings Enclosure Material Sensor Housing Material Max Cable Length for Remote-Mounted Kit Dimensions Weight

Lethathamo la 1: Litlhaloso

Keketseho ea Range Range

0-25.0% molumo

0.1% ea molumo

0-5.0 ppm

0.1 ppm

0-100 ppm

1 ppm

0-5.0 ppm

0.1 ppm

0-20 ppm

1 ppm

Haze. Sebaka.
Cl. 1 Div. 1 Cl. 1 Div. 2
Cl. 1 Div. 1

Phatlalatso · liteishene tsa O2: Ha ho khatello ea zero · Mecha e meng eohle: 1% ea tekanyo e feletseng · Ho phatloha / Lelakabe-Bopaki · IP-51 Sehlopha sa I, Sehlopha sa 1, Lihlopha tsa B, C, D Ex db IIB Gb Sehlopha sa I, Zone 1, AEx db IIB Gb Tamb -40 ° C ho +60 ° C
Sehlopha sa I, Karolo ea 1 (kapa Karolo ea 2), Lihlopha tsa B, C, D Ex db IIB Gb Tamb -40°C ho ea +60°C
ELA HLOKO: Setifikeiti se sebetsa feela ho likhase tse ling. Likhase tse chefo tse sa netefatsoang bakeng sa Div. Libaka tse 1 li loketse Div. Likopo tse 2 empa ha li na tumello ea motho oa boraro.
12 - 35 VDC
250 MAA, max
-40°C ho ea +54°C (-40°F ho ea +129°F)

0 - 98% mongobo o lekanyelitsoeng, o sa fokotseheng · 4 ho 20 mA (3-terata) · RS-485 Modbus RTU · 3A ho 24 VDC, 115 VAC, le 250 VAC · setsi se seng le se seng sa relay se sirelelitsoeng ke 4A fuse Aluminium
303 Stainless steel · Electrochemical (EC): 250 maoto · Infrared (IR): 40 maoto · Catalytic: 15 maoto 5.5″ D x 6″ W x 7″ H
6 lik'hilograma

Buka ea Ts'ebetso ea T3A

Litlhaloso · 9

Lisebelisoa tse tloaelehileng

· Tšireletso ea pula (e rometsoe ka li-detectors tsa O2, CO, H2S, CO2, le LEL feela)
· Magnet

TLHOKOMELISO: Ha o sebelisa T3A, o tlameha ho latela litaelo le litemoso tse bukeng ena ho netefatsa ts'ebetso e nepahetseng le e bolokehileng ea T3A le ho fokotsa kotsi ea ho tsoa kotsi. Netefatsa hore o boloka le ho lekanya T3A nako le nako joalokaha ho hlalositsoe bukeng ena.

10 · Litlhaloso

Buka ea Ts'ebetso ea T3A

Tlhaloso ea Kantle

Setšoantšo sa 1: T3A Sebaka sa Karolo ea Kantle

1 konopo ea MENU

8 Kopano ea matlo a li-sensor

2 Sekoahelo se ka pele sa phanele

9 Molebeli oa pula*

3 Sekepe

10 Sesebelisoa sa makenete

4 polaka e thibelang ho phatloha

11 Alamo 1 LED

5 konopo ea SUB

12 konopo ea ADD

6 Sekoti se penyang

13 Sekurufu sa ho notlela sekwahelo sa sekwahelo

7 Alamo 2 LED

14 Skrine e bonts'ang

* E rometsoe ka li-detectors tsa O2, CO, H2S, CO2, le LEL feela HLOKOMELA: Li-conduit hubs tsa T3A ke 3/4 NPT.

Buka ea Ts'ebetso ea T3A

Tlhaloso ea Kantle · 11

Tlhaloso ea ka hare

Setšoantšo sa 2: Sebaka sa Karolo ea ka hare

1 RS-485 Modbus terminal block

2 Li-terminal block tsa liphoso

3

Motlakase oa ho kenya / 4-20 mA block terminal ea tlhahiso

4 Ha ea kengoa ho T3A

5 Sensor housing socket 6 Ha ea kengoa ho T3A 7 Relay 1 terminal block (haeba li-relay li kentsoe)
8 Relay 2 terminal block (haeba li-relay li kentsoe)

12 · Tlhaloso ea ka hare

Buka ea Ts'ebetso ea T3A

Seqhoa se Qhobehileng

Setšoantšo sa 3: Setšoantšo se Phatlohileng

1 Sekoahelo se koaletsoeng

8 Motheo oa matlo a li-sensor

2 Tsamaiso ea ka hare

9 Karolo ea kutlo

3 Ha ea kengoa ho T3A

10 Molebeli oa pula*

4 'Mele o koaletsoeng

Sensor housing cap (e nang le sekoahelo sa mollo bakeng sa Sehlopha sa 1
11 Div. 1 likopano; ntle le sekoahelo sa mollo bakeng sa Sehlopha sa 1
Div. 2 likopano)

5 Ha ea kengoa ho T3A

12 Boto ea sensor ea Analog

6 Ha ea kengoa ho T3A

13 Sensor housing plug

7 Plaka e thibelang ho phatloha

* E rometsoe ka li-detectors tsa O2, CO, H2S, CO2, le LEL feela

Buka ea Ts'ebetso ea T3A

Setšoantšo se phatlohileng · 13

Remote-Mounted Kit

Setsi sa sensor se kentsoeng hole se ka laeloa haeba sensor e hloka ho ba kae-kae moo ho seng bonolo ho fihlella viewho shebella skrineng.
Thepa e kenyelletsa lebokose la bobeli la mateano holim'a mohala o nang le cable bushing / cable gland. Cable e ka odara ka li-increments tsa 1-foot ka bolelele bo boholo ba cable bo thathamisitsoeng ka tlase.

Mofuta oa Sensor
Electrochemical (EC) Infrared (IR)

Bolelele ba Cable bo Bogolo
250 maoto a 40 maoto

Catalytic

15 maoto

The cable le cable bushing/cable gland ha se tse thibelang ho phatloha. Haeba kopano e kenngoa sebakeng se khethiloeng, cable bushing e tlameha ho tlosoa ebe e nkeloa sebaka ke conduit-proof proof. U tlameha ho kopana le likhoutu tsa motlakase tsa lehae mme u sebelise mokhoa o nepahetseng oa kaho ho boloka sehlopha sa kopano se sa chang ha ho phatloha.

14 · Remote-Mounted Kit

Buka ea Ts'ebetso ea T3A

Ho kenya
Karolo ena e hlalosa mekhoa ea ho kenya T3A tikolohong ea ho beha leihlo le ho kenya mohala oa T3A.
Ho hlophisoa ha T3A
1. Nahana ka lintlha tse latelang ha u khetha sebaka sa ho kenya. · Khetha sebaka seo ho sona T3A e ke keng ea thula kapa ea sitisoa. Etsa bonnete ba hore ho na le sebaka se lekaneng sa ho qala, ho lokisa, le mekhoa ea ho lekanya. · Khetha sebaka se emelang tikoloho ea ho beha leihlo le moo khase e lebeletsoeng e ka bokellanang teng kapa moo ho nang le monyetla oa hore e lutle. T3A ha ea lokela ho kenngoa haufi le monyako, moea o kenang, kapa sebaka sa ho tima. · Sensor e tlameha ho supa tlase. • Qoba ho kenya T3A sebakeng seo likaroloana tse tsamaeang ka moea li ka koahelang kapa tsa koahela sensor.
ELA HLOKO: Litaelo tsena li reretsoe FEELA joalo ka taelo e akaretsang ea ho beoa ha T3A. Tlhahisoleseding ena HA E LOKELA ho sebetsa e le lenane le felletseng ha ho nahanoa ka likarolo tsohle tse ka bang teng bakeng sa sebaka se nepahetseng sa yuniti. Ho eletsoa HAHOLO hore motho oa boraro Certified Industrial Hygienist, kapa Certified Safety Professional, a etse tlhahlobo ea sebaka le ho hlakisa sebaka le bongata ba lisebelisoa tsa ho lemoha tse lokelang ho kengoa bakeng sa ho kengoa KA HO TSOHLE ha saete E MONG LE E MONG.

Buka ea Ts'ebetso ea T3A

Tlhomamiso · 15

2. Khetha sebaka se ntseng se hola le lisebelisoa tsa ho kenya. Ho hloella mohahong oa konkreite kapa oa tšepe ho khothalletsoa ho fokotsa ho thothomela le mongobo. Sebelisa boholo ba 1/4″-20 bolt kapa 1/4″ diameter screw, liwasha tse bataletseng, thepa ea Kereiti ea 5, le ts'ireletso ea kutu joalo ka pente, galvanization, kapa zinc plating.
6.00
5.50

0.25 7.16

4.49 9.16

Ø 2.00
Setšoantšo sa 4: Litekanyo tsa T3A

16 · Ho kenya

Buka ea Ts'ebetso ea T3A

3. Bakeng sa khiti e kentsoeng ka hole, kenya lebokose la mateano la detector tikolohong ea ho beha leihlo u sebelisa mekhoa e loketseng ho hlophisoa ha sebaka se hlongoang le khoutu ea motlakase ea lehae. The cable le cable bushing/cable gland tse rometsoeng le kopano ha li khone ho phatloha. TLHOKOMELISO: Haeba e kentsoe sebakeng se ikhethileng, sebelisa mokhoa o nepahetseng oa kaho ho boloka likarolo tsa kopano e ke keng ea phatloha. 4.64
9.95

2.70
Setšoantšo sa 5: Litekanyo tsa Lebokose la Remote-Mounted Kit's Junction Box

Buka ea Ts'ebetso ea T3A

Tlhomamiso · 17

Wiring ea Remote-Mounted Kit
Thepa e kentsoeng ka remoutu hangata e tla e kentsoe pele empa ha e ka khaoha, latela mehato ena ho e hokela hape.
TLHOKOMELISO: Likarolo tse ka hare li ka ba bonolo. E-ba hlokolosi ha u bula sebaka se ka hare le ho tšoara likarolo tsa ka hare.
TLHOKOMELISO: Etsa bonnete ba hore mohloli oa matla o tima pele o qala mokhoa oa ho kenya motlakase.
TLHOKOMELISO: U SE KE UA sebelisa lintho leha e le life tsa tšepe kapa lisebelisoa ho tlosa boto ea ho qetela tsamaisong ea ka hare.
1. Hlakola sekoaelo se seng le se seng 'me u se behelle ka thōko. 2. Ho ampLifier junction box, tšoara li-thumbcrews 'me ka bonolo u phahamise tsamaiso ea ka hare ho tsoa
sebaka se kampetsoeng. E ka phomola pheletsong ea sebaka se kampetsoeng. 3. Karolo e 'ngoe ea thapo e na le sehokelo ha e 'ngoe e na le likhoele tse ferekaneng. 4. Fepa pheletsong ea sehokelo sa thapo ka 3/4 NPT conduit hub ho ampmateano a lifier
lebokose.
TLHOKOMELISO: Haeba e kentsoe sebakeng se ikhethileng, sebelisa mokhoa o nepahetseng oa kaho ho boloka likarolo tsa kopano e ke keng ea phatloha.
5. Hokela sehokelo ka har'a sokete ea sehokelo sa sensor ho amplebokose la mateano la lifier. 6. Fepa pheletsong ea terata e nonneng ka 3/4 NPT conduit hub mateanong a detector.
lebokose.
TLHOKOMELISO: Haeba e kentsoe sebakeng se ikhethileng, sebelisa mokhoa o nepahetseng oa kaho ho boloka likarolo tsa kopano e ke keng ea phatloha.
7. Hokela lithapo tse ferekaneng ho litheminale tse nang le mebala ka lebokoseng la mateano la detector. 8. Sireletsa sekoahelo sa lebokose la mateano la sesupa hore se khutlele holim'a sebaka se kampetsoeng.

18 · Ho kenya

Buka ea Ts'ebetso ea T3A

Matla a Wiring le 4-20 mA Output
T3A e na le litlhophiso tse 'maloa tsa mantlha tsa wiring, ho ipapisitse le ts'ebeliso e lakatsehang le ts'ebetso e reriloeng ke mosebelisi. Li-unit tsohle tsa T3A li hloka +12 ho ea ho +35 Volts ea matla a DC a masela hore a sebetse. Puisano ea data ho tsoa sesebelisoa, ka tlhahiso ea 4-20 kapa khokahanyo ea RS485 Modbus, ho ea sebakeng sa kantle ke boikhethelo.
TLHOKOMELISO: Likarolo tse ka hare li ka ba bonolo. E-ba hlokolosi ha u bula sebaka se ka hare le ho tšoara likarolo tsa ka hare.

TLHOKOMELISO: Etsa bonnete ba hore mohloli oa matla o tima pele o qala mokhoa oa ho kenya motlakase.

TLHOKOMELISO: U SE KE UA sebelisa lintho leha e le life tsa tšepe kapa lisebelisoa ho tlosa boto ea ho qetela tsamaisong ea ka hare.

Letlapa la 2: Likhakanyo tsa mohala tsa T3A Terminal Block Wire Gauges

Thibelo ea Terminal
Terminal ea motlakase Relay 1 & 2 terminal

Mohala oa terata
Min: 26 AWG Max: 14 AWG

Seteishene sa Modbus Fault terminal

Min: 26 AWG Max: 16 AWG

1. Hlakola sekoaelo sa sekoahelo ebe u se beha ka thōko.
2. Tšoara li-thumbscrews 'me ka bonolo u phahamise tsamaiso ea ka hare ho tsoa ka ntle. E ka phomola pheletsong ea sebaka se kampetsoeng.
TLHOKOMELISO: Ho khaola sekontiri sa sekontiri ho tloha ntlong ea sensor ho tla lumella ho tlosoa ka ho feletseng ha tsamaiso ea ka hare ho tswa ho sesebelisoa. Ho khaola tsamaiso ea ka hare ho ka fana ka boiketlo ba ho fumana li-terminals tsa boto ea taolo bakeng sa wiring. Hokela hape sehokelo sa sensor pele o kenya sistimi e kahare hape.

TLHOKOMELISO: Sebelisa mokhoa o nepahetseng oa ho aha ho boloka sehlopha sa kopano se ke keng sa phatloha.

Buka ea Ts'ebetso ea T3A

Tlhomamiso · 19

3. Fepa matla le lithapo tsa mehala tsa 4-20 mA ka setsi sa motlakase sa T3A's 3/4 NPT le ho kena ka har'a sebaka se kampetsoeng.
HLOKOMELA: Matla a khoele ho sesebelisoa ke eona FEELA e hlokahalang hore T3A e sebetse. Ka matla, yuniti e tla sebetsa ka mokhoa o tloaelehileng, e bonts'a boteng ba khase e chefo ho sensor le ho fana ka ho baloa ha boemo ba khase skrineng sa ponts'o. Ho sebelisa ts'ebetso e eketsehileng ea sesebelisoa, ho hlokahala wiring e eketsehileng. Haeba molaoli a sa sebelisoe, T3A e ka tsamaisoa ho tloha leha e le efe +12 ho ea ho +35 VDC ea motlakase e khonang ho fana ka bonyane 250 mA.
4. Fumana boloko ba motlakase letlapeng la taolo 'me u tlatse tse latelang (sheba setšoantšo sa 6). · Hokela terata ea motlakase (GRAY) ho terminal ea VDC +. • Hokela terata ea fatše (BLACK) ho VDC - theminale. · Hokela mohala oa lets'oao (TATALA) ho theminale ea 4-20 mA (S).
TLHOKOMELISO: Haeba ho sebelisoa thapo e sirelelitsoeng, tlohela terata ea drain ea thebe e khaotsoe 'me e sirelelitsoe T3A. U tla hokela pheletsong e fapaneng ea terata ea drain ea thapo ho chassis (lefatše) ea molaoli.
5. Tsamaisa thapo kapa lithapo tse tsoang T3A ka e 'ngoe ea li-conduit hubs ntlong ea molaoli.
TLHOKOMELISO: Se ke oa tsamaisa matla le likhoele tsa T3A ka har'a sebaka se le seng sa controller conduit hub. Thapo ea matla e ka sitisa phetiso ea lets'oao la T3A ho molaoli.
6. Hokela lithapo ho theminale e sebetsang ea detector ho molaoli joalokaha ho bontšitsoe setšoantšong sa 6.

20 · Ho kenya

Setšoantšo sa 6: Matla a Wiring le Wiring ea Signal

Buka ea Ts'ebetso ea T3A

7. Haeba ho sebelisoa thapo e sirelelitsoeng, hokela terata ea drain ea thapo sebakeng se fumanehang sa chassis (lefatše) ho molaoli. Balaoli ba RKI hangata ba na le sekoti sa fatše se ka sebelisoang ho theola terata ea drain ea thapo.

Ho kopanya RS-485 Modbus
T3A e ts'ehetsa Modbus RTU ka sehokelo sa RS-485.
Letlapa la 3: Likhakanyo tsa mohala tsa T3A Terminal Block Wire Gauges

Thibelo ea Terminal
Terminal ea motlakase Relay 1 & 2 terminal

Mohala oa terata
Min: 26 AWG Max: 14 AWG

Seteishene sa Modbus Fault terminal

Min: 26 AWG Max: 16 AWG

1. Haeba ho hlokahala, tlosa sekoahelo se koaletsoeng 'me u hule tsamaiso ea ka hare ka li-thumbscrews. TLHOKOMELISO: Etsa bonnete ba hore matla a T3A a tima pele o hula sistimi e ka hare.

2. Fepa thapo ea RS-485 ka setsi sa matla sa 3/4 NPT le ho kena ka har'a sebaka se kampetsoeng.
TLHOKOMELISO: Sebelisa mokhoa o nepahetseng oa ho aha ho boloka sehlopha sa kopano se ke keng sa phatloha.

3. Hokela terata ea RS-485 B (BROWN) ho B theminale. 4. Hokela terata ea fatše (BLACK) ho theminale ea GND. 5. Hokela terata ea RS-485 A (YELLOW) ho terminal ea A.

Buka ea Ts'ebetso ea T3A

Tlhomamiso · 21

6. Fepa thapo ea RS-485 ka har'a hub ea matla le ho molaoli 'me u li kenye liteisheneng tse nepahetseng joalo ka ha ho bontšitsoe ka tlase.

Setšoantšo sa 7: Wiring ea Modbus
HLOKOMELA: Haeba molaoli oa RKI o sa sebelisoe, T3A e ka hokeloa ho Programmable Logic Controller (PLC) bakeng sa likhokahano tsa data tsa RS-485 Modbus. Bakeng sa kopanyo le ho seta, sheba 'Mapa oa Ngoliso oa Modbus o fumanehang ho Sehlomathiso sa C sa bukana ena.

22 · Ho kenya

Buka ea Ts'ebetso ea T3A

Ho hokahanya li-Relay / Alarms
Li-relay tsa T3A li atisa ho sebelisoa ho matlafatsa le ho laola lisebelisoa tse ka ntle tse tšosang, tse kang mabone a alamo (a bonoang) le manaka (molumo).

HLOKOMELA: Li-relay li sirelelitsoe ke li-fuse tsa 4A tse ka nkeloang sebaka.

Letlapa la 4: Likhakanyo tsa mohala tsa T3A Terminal Block Wire Gauges

Thibelo ea Terminal
Terminal ea motlakase Relay 1 & 2 terminal

Mohala oa terata
Min: 26 AWG Max: 14 AWG

Seteishene sa Modbus Fault terminal

Min: 26 AWG Max: 16 AWG

1. Haeba ho hlokahala, tlosa sekoahelo se koaletsoeng 'me u hule tsamaiso ea ka hare ka li-thumbscrews. TLHOKOMELISO: Etsa bonnete ba hore matla a T3A a tima pele o hula sistimi e ka hare.

2. Fepa mehala ea relay/alamo ka hub ea matla ea 3/4 NPT le ka har'a sebaka se kampetsoeng. 3. Batla li-terminals tsa relay botong ea radio/relay.
TLHOKOMELISO: Sebelisa mokhoa o nepahetseng oa ho aha ho boloka sehlopha sa kopano se ke keng sa phatloha.

4. Hokela theminale ea matla a alamo (RED) ho terminal ea NO kapa NC sebakeng sa relay block block.
ELA HLOKO: Ho khothaletsoa hore likhokahano tsa relay li kenngoe ka lithapo ka mokhoa o tloaelehileng-o butsoe (NO). Leha ho le joalo, litlhophiso tsa likhoele tse koetsoeng ka tloaelo (NC) li fana ka ts'ireletso ea tlhaho 'me li ka ratoa.

5. Hokela theminale ea fatše ea sesebelisoa sa alamo (TATALA) ho theminale ea "-" ea mohloli o ka ntle oa matla.

Buka ea Ts'ebetso ea T3A

Tlhomamiso · 23

6. Hokela theminale ea "+" ea mohloli o ka ntle oa matla (GRAY) ho theminale ea COM sebakeng sa boloko ba relay.
Setšoantšo sa 8: Relay Wiring

24 · Ho kenya

Buka ea Ts'ebetso ea T3A

Ho kopanya Fault Terminal
Fault terminal e sebediswa ho fana ka sesupo sa ho hloleha ha sesebediswa (ka mabaka a thathamisitsweng leqepheng la 57 kapa bakeng sa ho hloleha ha motlakase). Setsi sa phoso se romelloa se lokiselitsoe joalo ka tloaelo-e koetsoeng (NC), kapa failsafe, tlhophiso, matla a ho felisa sesebelisoa sa phoso sa kantle ha se khothalletsoa. Ho fetola boitšoaro bona ho hlalositsoe leqepheng la 36.
Ho fapana le li-terminals tsa boikhethelo tsa li-relay, fault terminal ke motho ea hokahaneng le metsi, e hlokang feela lithapo tsa motlakase le tsa fatše tsa sesebelisoa sa phoso se kantle ho hokeloa nakong ea ho kenya. Nakong ea ts'ebetso e tloaelehileng, setsi sa phoso se fana ka boholo ba 500 mA ka molumo o tšoanangtage e fanoang ho block terminal ea motlakase.
Letlapa la 5: Likhakanyo tsa mohala tsa T3A Terminal Block Wire Gauges

Thibelo ea Terminal
Terminal ea motlakase Relay 1 & 2 terminal

Mohala oa terata
Min: 26 AWG Max: 14 AWG

Seteishene sa Modbus Fault terminal

Min: 26 AWG Max: 16 AWG

1. Haeba ho hlokahala, tlosa sekoahelo se koaletsoeng 'me u hule tsamaiso ea ka hare ka li-thumbscrews. TLHOKOMELISO: Etsa bonnete ba hore matla a T3A a tima pele o hula sistimi e ka hare.

2. Fumana lithapo tsa matla (RED) le fatše (BLACK) sesebelisoa se tšosang.
TLHOKOMELISO: Sebelisa mokhoa o nepahetseng oa ho aha ho boloka sehlopha sa kopano se ke keng sa phatloha.

3. Fepa lithapo tsa sesebelisoa se tšosang ka setsi sa motlakase sa 3/4 NPT le ka har'a sebaka se kampetsoeng. 4. Fumana sebaka sa "fault terminal block" letlapeng la taolo. 5. Hokela mohala oa sesebelisoa sa phoso sa kantle (RED) ho + terminal.

Buka ea Ts'ebetso ea T3A

Tlhomamiso · 25

6. Hokela terata ea sesebediswa se sebe sa kantle (BLACK) ho the - terminal.

Setšoantšo sa 9: Wiring ea Phoso ea Terminal
Ho koala Sebaka se Koaletsoeng
1. Beha tsamaiso ea ka hare ka har'a sebaka se koetsoeng, u bapisa poso e 'ngoe le e' ngoe e ntseng e phahama le leihlo la eona le ts'oaretsoeng ka har'a motheo oa sebaka se kampetsoeng.
2. U sebelisa li-thumbscrews, sutumelletsa ka bonolo ho beha tsamaiso ea ka hare ho li-post posts.
TLHOKOMELISO: Li-thumbscrews tse ho T3A li sebetsa FEELA joalo ka ho ts'oara monoana o motona bakeng sa ho tlosa tsamaiso ea ka hare ho tloha motheong oa sebaka. SE KE UA leka ho lokolla kapa ho tiisa li-thumbcrews ha u bula kapa u koala sebaka se kampetsoeng.
3. Netefatsa hore selikalikoe sa ho tiisa, se lutseng moo ho butsoeng ka khoele ea sebaka se kampetsoeng sa sesebelisoa, se sebakeng se nepahetseng.
4. Sireletsa sekoahelo se kampetsoeng hape.
TLHOKOMELISO: Ha u tiisa sekoahelo sesebelisoa, tiisa sekoaelo ka letsoho FEELA. Ho tiisa sekoahelo ka ho sebelisa lisebelisoa tsa letsoho ho ka baka tšenyo ho O-ring, e ka 'nang ea senya tiiso ea mongobo, e leng se etsang hore ho be le tikoloho e sa sireletsehang.

26 · Ho kenya

Buka ea Ts'ebetso ea T3A

E qalang
Karolo ena e hlalosa mekhoa ea ho qala T3A le ho beha T3A ts'ebetsong e tloaelehileng. 1. Qetella mekhoa ea ho instola e hlalositsoeng pejana bukeng ena. 2. Netefatsa hore mohala oa motlakase o nepahetse ebile o bolokehile. 3. Bulela mohloli oa matla. 4. Netefatsa hore molaoli o ntse a sebetsa le hore o sebetsa hantle. Sheba ho opareitara ea taolo
tataiso. 5. T3A e ikemela ka bo eona ebe e kenya nako ea ho qala ea metsotso e 1.
6. Qetellong ea ho qala, T3A e Moetlong o Tloaelehileng oa Operating.
1. Mekhahlelo ea khase e lekantsoeng (ho bala) 2. Karolo ea khatello ea khase ea tekanyo 3. Mofuta oa khase ea sensor element

Buka ea Ts'ebetso ea T3A

Ho qala · 27

7. Lumella mochine o futhumatsang nako e loketseng joalokaha ho bontšitsoe ka tlase, ho itšetlehile ka mofuta oa sensor.

Khase ea ho Khetholla

Nako ea ho futhumatsa

Nako ea ho futhumatsa

Ka mor'a ho Atolosoa Ka mor'a Nako e Khutšoane

Nako Off Power Nako Off Power

Ammonia (NH3) Arsine (AsH3) Carbon Dioxide (CO2) Carbon Monoxide (CO)

Lihora tse 12 lihora tse 2 metsotso e 10 lihora tse 2

Lihora tse 4 metsotso e 10

Chlorine (Cl2) Chlorine Dioxide (ClO2) Khase e tukang

metsotso e 10

Ethylene oxide (EtO)

Lihora tse 48

Formaldehyde (CH2O) Hydrogen (H2) Hydrogen Chloride (HCl)

Metsotso e 10 lihora tse 2 lihora tse 12

Hydrogen Cyanide (HCN)

Hydrogen Fluoride (HF)

Lihora tse 2

Hydrogen Sulfide (H2S) Nitric Oxide (NO)

Lihora tse 12

Nitrogen Dioxide (NO2) Oxygen (O2) Ozone (O3) Phosphine (PH3) Sulfur Dioxide (SO2)

Lihora tse 2

8. T3A e lekantsoe fektheri pele e romelloa ho tloha RKI. Haeba u batla ho lekanya ka botlalo qalong, sheba leqephe la 47.

28 · Qala Up

Buka ea Ts'ebetso ea T3A

Tshebetso
TLHOKOMELISO: Se ke oa tlosa sekoaelo sa ntlo ea sensor kapa sekoaelo se koaletsoeng ha lipotoloho li ntse li matlafatsoa ntle le haeba sebaka se ikemiselitse ho se be kotsi. Boloka sekoaelo sa ntlo ea sensor le sekoaelo se koaletsoeng se koetsoe ka thata nakong ea ts'ebetso.
Mokhoa o tloaelehileng oa ho sebetsa
Ha e ntse e le Mokhoa o Tloaelehileng oa Ts'ebetso, T3A e tsoela pele sampe fokotsa moea le ho nchafatsa boemo bo lekantsoeng ba khase e shebiloeng skrineng sa ponts'o. Pontsho, ha e le Mokgweng wa Tlwaelo wa Tshebetso, e hlaha jwalo ka ha ho bontshitswe ka tlase.

1. Mekhahlelo ea khase e lekantsoeng (ho bala) 2. Karolo ea khatello ea khase ea tekanyo 3. Mofuta oa khase ea sensor element

Ho bala ka holimo ho tekanyo e feletseng (4-20 mA tlhahiso ke 25 mA)

Likonopo tsa Magnetic
Sebelisa makenete e fanoeng ho kenya likonopo tsa T3A ntle le ho tlosa sekoaelo sa lebokose la mateano. Thetsa makenete ntlheng e ka ntle ea sekwahelo sa lebokose la mateano haufi le konopo eo u batlang ho e kenya. Ho tlanya lebokose la mateano ho tšoana le ho tobetsa le ho lokolla konopo. Ho tšoara makenete khahlanong le lebokose la mateano ho tšoana le ho tobetsa le ho tšoara konopo.
Tobetsa makenete mona ho kenya konopo ea MENU

Tobetsa makenete mona ho kenya konopo ea ADD

Tobetsa makenete mona ho kenya konopo ea SUB

Buka ea Ts'ebetso ea T3A

Ts'ebetso · 29

Ho matlafatsa Sesebelisoa
Ha matla a qala ho sebelisoa ho T3A, yuniti e qala ka bo eona ebe e qala tatellano ea ho qala. Litaelo tse ka tlase li hlalosa mokhoa oa ho tima le ho kenya motlakase ho T3A hang ha motlakase o se o sebelisitsoe.
Ho tima Power
Ho tima sesebelisoa ho emisa ts'ebetso ea yuniti. Litlhophiso tsa Sehlahisoa le Tlhophiso, hammoho le litlhophiso tsa ts'ebetso, ho kenyeletsoa zero le calibration ea sensor, li ke ke tsa ameha. 1. Tobetsa 'me u tšoare konopo ea SUB metsotsoana e ka bang 6, ho fihlela "OFF" e hlaha skrineng
skrineng.
2. Skrine ea ponts'o e tla tsoela pele ho bontša "OFF" ka nako ea nako eo sesebelisoa se timang, hafeela matla a sa sitisoeng a fanoa ho unit.
Ho Matlafatsa
Ho kenya matla sesebelisoa ho qala ts'ebetso ea yuniti, ho qala ka mokhoa o ikhethileng potoloho ea ho qala sistimi le nako ea ho futhumatsa ea metsotso e 1. T3A e tla ba maemong a tloaelehileng a ts'ebetso ha ho phetheloa ha sistimi e qala. Ho bulela T3A, tobetsa ADD hang.
Seta Botjha ka Matsoho bakeng sa Dialamo Tse Kentsweng Tshebetso
Lialamo tse fetisetsoang ho latching li ke ke tsa tima ho fihlela lialamo li setiloe bocha sesebelisoa. Sena se kenyelletsa li-LED tsa Alarm 1 le Alarm 2 le li-relays tsa boikhethelo. Ha lialamo tsa latching li kentsoe tšebetsong, sheba litaelo tse latelang mabapi le mokhoa oa ho tima lialamo sesebelisoa sa hau: 1. Netefatsa hore boemo ba khase bo baloa ka tlase ho boemo ba alamo.
2. Tobetsa konopo ea MENU ho tima alamo (alamo).
ELA HLOKO: Palo ea boemo ba khase e LOKELA ho ba ka tlase ho boemo ba alamo pele alamo e ka tima. Tobetsa konopo ea MENU hang FEELA ho tima alamo (li)alamo. Ho tobetsa konopo ea MENU ho feta hang ho tla kenya tšebetsong le ho bula menyetla ea Operation Settings. Lialamo HA LI TLA sebetsa, leha ho na le khase, ho fihlela u tsoile ho menu hoo e ka bang motsotso o le mong.

30 · Ts'ebetso

Buka ea Ts'ebetso ea T3A

Liphoso
Ha sesebelisoa se hloleha, sesebelisoa se tla fapanyetsana pakeng tsa skrine e tloaelehileng ea ts'ebetso le skrine ea phoso ho pontšo, ka nako ea metsotsoana ea 5, ho fihlela phoso e hlakotsoe, kapa e lokisoa. Khoutu ea phoso, e karolong e ka tlaase-leqeleng la pontšo, e hlaha skrineng ka bobeli. Yuniti e lula e ngolisa hore sistimi e na le phoso. Ha phoso e lokisoa, sesebelisoa se tla khutlela ho mokhoa o tloaelehileng oa ho sebetsa.
Bakeng sa lethathamo la likhoutu tsa liphoso le matšoao a temoso a T3A, le moelelo oa tsona o amanang, bona leqephe la 57.
Ho kena ho Menus
Ka bobeli li-menu tsa sistimi li fumaneha ho tsoa ho Mokhoa o Tloaelehileng oa Ts'ebetso. Ho fihlella Litlhophiso tsa Sehlahisoa le menyu ea Tlhophiso, tobetsa o hatelle konopo ea MENU, hoo e ka bang metsotsoana e 6, ho fihlela menu e kentsoe tšebetsong le ho buloa skrineng sa ponts'o. Ho fihlella menu ya Operation Settings ho tswa ho Normal Operating Mode, tobetsa le ho lokolla konopo ya MENU hang mme menu e tla buleha mme e hlahe skrineng.
TLHOKOMELISO: Kamora metsotso ea 5 ea ho se sebelisane le sesebelisoa, yuniti e tla khutlela ka mokhoa o tloaelehileng oa ts'ebetso.

Buka ea Ts'ebetso ea T3A

Ts'ebetso · 31

Litlhophiso tsa Sehlahisoa le Tlhophiso
Lenane la Litlhophiso tsa Sehlahisoa le Litlhophiso li lumella mosebelisi ho etsa litlhophiso tsa sesebelisoa hore li finyelle litlhoko tsa bona tse hlokahalang le/kapa maemo a sebaka. T3A e tsoela pele ho beha leihlo bakeng sa khase ha e ntse e le ho Litlhophiso tsa Sehlahisoa le menyu ea Litlhophiso. Lenane la Litlhophiso tsa Sehlahisoa le Litlhophiso li na le li-skrini tse latelang:
· Tlhahlobo ea Alamo (sheba leqephe la 33) · Boitsebiso ba Tsamaiso (sheba leqephe la 34) · Zero / Calibration Timers (bona leqephe la 34) · Info Unit (bona leqephe la 35) · Relay 1: Latching / Auto Resetting Setting (sheba leqephe la 35) · Relay 2: Latching/Auto Resetting Setting (bona leqephe la 36) · bona leqephe la 1 (bona leqephe la 36) · Relay 2: Tlhophiso e Sireletsehileng (sheba leqephe la 38) · Fault Terminal Fail-Safe Setting (bona leqephe la 38) · Mokhoa oa ho Lekanya (sheba leqephe la 39) · RS-485 Modbus Aterese Setting (bona leqephe la 39) · RS-485 Modbus Baud Setting (bona leqephe la 40-4 Offset Setting, Zero20 Setting Setting, Offset Setting) RS-41 Tlhophiso e Felletseng ea Offset (sheba leqephe la 42) · Pontšo ea Phapang ea Sekrine (sheba leqephe la 43) · Khutlela ho Litlhophiso tsa Kamehla tsa Fektheri (sheba leqephe la 45) · Seta Bocha Maemo a Zero le a Calibration Feela (sheba leqephe la XNUMX)
Ho kenya Litlhophiso tsa Sehlahisoa le Menu ea Tlhophiso
Ha sesebediswa se le mokgweng o tlwaelehileng wa ho sebetsa, tobetsa o hatelle konopo ya MENU, hoo e ka bang metsotswana e 6, ho fihlela Di-setting tsa Sehlahiswa le menu ya Tlhophiso e kentswe tshebetsong mme e buleha skrineng sa pontsho.
TLHOKOMELISO: Kamora metsotso ea 5 ea ho se sebelisane le sesebelisoa, yuniti e tla khutlela ka mokhoa o tloaelehileng oa ts'ebetso.
TLHOKOMELISO: Lialamo li TLA ke ke tsa sebetsa, leha ho na le khase, ho fihlela u tsoile ho Litlhophiso tsa Sehlahisoa le Menu ea Litlhophiso ka motsotso o le mong.

32 · Litlhophiso tsa Sehlahisoa le Tlhophiso

Buka ea Ts'ebetso ea T3A

Teko ea Alamo
Teko ea alamo e etsisa boemo ba khase. Teko ea alamo e sebelisoa ho netefatsa ts'ebetso e nepahetseng ea litlhophiso tsa relay ho molaoli. Teko e ka boela ea sebelisoa ho etsisa lithupelo tsa ts'ireletso / ts'ireletso sebakeng.
TLHOKOMELISO: Ho kenya li-relay tsa T3A ho tla etsisa Alarm 1 le Alarm 2 relays ho molaoli. Balaoli ha ba khone ho khetholla pakeng tsa data ea sebele le e etsisitsoeng e amohetsoeng. Ha li-relay tsa controller li qala, lisebelisoa tsa alamo li tla sebetsa kamoo li reriloeng kateng, li qale mekhoa ea tšohanyetso joalokaha eka ho na le khase e kotsi kapa e chefo. Ho thibela sena ho etsahala, seta molaoli mokgweng wa ho lekanya pele o etsa teko ya alamo. Mokhoa oa calibration o lumella phetiso ea data ntle le ts'ebetso ea relay.
Ho kgothaletswa hore ho etswe teko ya alamo MATSATSI LENG MONGWE LE a 30, mmoho le paballo le tlhophiso ya sethuthuthu.
Ho etsa Teko ea Alamo
Ho bala boemo ba khase ea alamo ho ka eketsoa kapa ho fokotseha ka li-increments tsa 5% ea sekala sa sensor, ho fihla ho 100% ea sekala sa sensor. 1. Kenya Litlhophiso tsa Sehlahisoa le menu ea Configuration ka ho tobetsa le ho tšoara konopo ea MENU
bakeng sa metsotsoana e 6. Ho hlaha skrine ea teko ea alamo.
2. Tobetsa konopo ea ADD ho fihlela maemo a Alarm 1 le Alarm 2 a fihletsoe 'me li-relay li hlohlelletsoa ho khantša li-alamo tsohle tse bonoang le ho letsa alamo (s) tsohle tsa molumo ho molaoli.
3. Hang ha li-relay tsohle li lekoa 'me tlhahlobo e phethiloe, tobetsa konopo ea SUB ho khutlisetsa tlhahlobo ea alamo ho zero le ho tima alamo ea molaoli.
4. Sebelisa konopo ea MENU ho tsamaea ka har'a karolo e setseng ea Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ebe u khutlela ho Mokhoa o Tloaelehileng oa Ts'ebetso.

Buka ea Ts'ebetso ea T3A

Litlhophiso le Tlhophiso ea Sehlahisoa · 33

Lintlha tsa Tsamaiso
Skrine ea tlhahisoleseling ea sistimi e lumella mosebelisi ho view lintlha tse latelang: · Sekala sa element element. · Phepelo voltage ea yuniti ea sensor. · The voltage bohlokoa (ka li-volts) tseo sensor e neng e li bala ha e le zero. · Karolo ea hajoaletage bohlokoa (ka li-volts) eo karolo ea sensor e e balang.
Skrine sena ke sa merero ea litaba feela. 1. Haeba ho hlokahala, kenya Li-setting tsa Sehlahisoa le menu ea Configuration ka ho tobetsa le ho tšoara
Konopo ea MENU bakeng sa metsotsoana e 6. 2. Tobetsa le ho lokolla konopo ea MENU ho fihlela skrine ea Tsamaiso ea Tsamaiso e hlaha.
3. Review tlhahisoleseding e hlahang. 4. Sebelisa konopo ea MENU ho tsamaea ho pholletsa le Litlhophiso tsa Sehlahisoa le Tlhophiso
menu ebe o khutlela ho Normal Operating Mode.
Litaba tsa Zero/Calibration Timer
Lethathamo la tlhahisoleseling la nako ea zero/calibration le lumella mosebelisi ho view lintlha tse latelang:
· Matsatsi ho tloha ha kopano ea sensor e qetelletse e le zero. · Matsatsi ho tloha ha kopano ea sensor e qetella e lekanyelitsoe. · Nomoro ea calibration ea sensor, e sebelisetsoang merero ea ho hlahloba. Skrine sena ke sa merero ea litaba feela.
ELA HLOKO: Sebaka sa Cal se intlafatsa ka bohona ka mor'a Auto Cal. Ha o etsa Manual Cal, 'malo oa khase o tlameha ho lokisoa ka ho tobetsa konopo e le' ngoe ho etsa hore sebaka sa Cal se ntlafatse.
1. Haeba ho hlokahala, kenya Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ka ho tobetsa le ho tšoara konopo ea MENU bakeng sa metsotsoana e 6.
2. Tobetsa o lokolle konopo ya MENU ho fihlela skrine sa Zero/Calibration Timer se hlaha.

34 · Litlhophiso tsa Sehlahisoa le Tlhophiso

Buka ea Ts'ebetso ea T3A

3. Review tlhahisoleseding e hlahang.
4. Sebelisa konopo ea MENU ho tsamaea ka har'a karolo e setseng ea Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ebe u khutlela ho Mokhoa o Tloaelehileng oa Ts'ebetso.
Lintlha tsa Unit
Skrine sa lintlha tsa yuniti se lumella mosebelisi ho view lintlha tse latelang: · Letsatsi la tlhahiso ea kopano ea sensor. · Nomoro ea serial ea kopano ea sensor.
Skrine sena ke sa merero ea litaba feela. 1. Haeba ho hlokahala, kenya Li-setting tsa Sehlahisoa le menu ea Configuration ka ho tobetsa le ho tšoara
Konopo ea MENU bakeng sa metsotsoana e 6.
2. Tobetsa le ho lokolla konopo ea MENU ho fihlela skrine ea Unit Information e hlaha.

3. Review tlhahisoleseding e hlahang.
4. Sebelisa konopo ea MENU ho tsamaea ka har'a karolo e setseng ea Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ebe u khutlela ho Mokhoa o Tloaelehileng oa Ts'ebetso.

Latching le Auto Setting Relay Settings

Relay 1 le Relay 2 li ka hlophisoa ho latching kapa auto reset. Li-relay tse behiloeng ho reset ea koloi li tla tima ka bo eona ha boemo ba khase bo bonoang bo oela ka tlase ho alamo e tsamaellanang le eona. Ka lehlakoreng le leng, li-relays tsa latching, ha li se li kentsoe tšebetsong, li TŠOANTŠE ho hlophisoa bocha mochineng, ho sa natsoe phetoho ea lipalo tsa boemo ba khase.

Litlhophiso tsa kamehla tsa feme bakeng sa Relay 1 le Relay 2 li seta bocha. Nakong ea ho kenya le ho seta, Relay 1 le Relay 2 hangata li etsoa ka mokhoa o latelang:

Lethathamo la 6: Litlhophiso tse tloaelehileng tsa Relay 1 le Relay 2

Relay
Relay 1 Relay 2

Alarm Setting
Alamo ea 1 Alamo 2

Latching/Auto Reset
Auto Reset Latching

Relay 1: Latching/Auto Reset Setting

1. Haeba ho hlokahala, kenya Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ka ho tobetsa le ho tšoara konopo ea MENU bakeng sa metsotsoana e 6.

Buka ea Ts'ebetso ea T3A

Litlhophiso le Tlhophiso ea Sehlahisoa · 35

2. Tobetsa o lokolle konopo ea MENU ho fihlela ho hlaha skrini sa Relay 1 Latching/Auto Resetting.

3. Sebelisa likonopo tsa ADD le SUB ho fetola lipakeng tsa "Auto Reset" le "Latch".
4. Tobetsa konopo ea MENU ho khetha tlhophiso e lakatsehang le ho fetela skrineng sa Relay 2 latching/auto reset.
TLHOKOMELISO: Bakeng sa li-alarmo tsa ho seta bocha, lialamo li ke ke tsa tima ho fihlela boemo ba khase ho sensor bo theohile ka 10% ka tlase ho sebaka sa alamo. Bakeng sa lialamo tsa latching, tekanyo ea khase e TLAMEHA e be ka tlase ho sebaka sa alamo pele alamo e ka tima. Lialamo HA LI TLA sebetsa, leha ho na le khase, ho fihlela u tsoile ho menu hoo e ka bang motsotso o le mong.
Relay 2: Latching/Auto Reset Setting
1. Haeba ho hlokahala, kenya Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ka ho tobetsa le ho tšoara konopo ea MENU bakeng sa metsotsoana e 6.
2. Tobetsa le ho lokolla konopo ea MENU ho fihlela skrine ea Relay 2 Latching/Auto Reset e hlaha.

3. Sebelisa likonopo tsa ADD le SUB ho fetola lipakeng tsa "Auto Reset" le "Latch".
4. Sebelisa konopo ea MENU ho tsamaea ka har'a karolo e setseng ea Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ebe u khutlela ho Mokhoa o Tloaelehileng oa Ts'ebetso.
Relay Fail-Safe Setting
Ho latela pono ea polokeho, boemo bofe kapa bofe bo sa tsejoeng bo tlameha ho nkuoa bo ka ba kotsi. Ha mochine o ikemetseng oa khase o sa khone ho bona khase, boemo bo sa tsejoeng bo bōptjoa 'me ho lokela ho nkoa mehato ea ho thibela kotsi kapa tahlehelo ea bophelo. Sena se bolela hore sesebelisoa se tlameha ho tseba ho lemosa mosebelisi hore ha se sa sebetsa ka botlalo. Ts'ebetso ena ea polokeho e etsoa hore e khonehe ke fault terminal. Ho fumana lintlha tse ling mabapi le terminal e nang le liphoso le ho fumana litaelo mabapi le mokhoa oa ho kenya terata sesebelisoa sa hau, sheba karolo ea Ho Hokela Fault Terminal bukeng ena.
Maemo a ikhethileng a sebaka a ka thibela ts'ebeliso ea "fault terminal", e lebisang maemong a kotsi ntle le tsebiso ea mosebelisi. Ho arabela, T3A e fana ka sebaka se sireletsehileng sa relay ho ntlafatsa ts'ireletso ea ts'ireletso e fanoeng ha sebaka sa phoso se ke ke sa sebelisoa.

36 · Litlhophiso tsa Sehlahisoa le Tlhophiso

Buka ea Ts'ebetso ea T3A

Boemo ba ho hloleha ha li-relay bo khutlisetsa morao boitšoaro ba li-relay 'me bo lumella relay e sa sebetseng ho sebetsa e le temoso ea ketsahalo e ka bang kotsi. Boemong ba ho hloleha, li-relay li kentsoe tšebetsong ha sesebelisoa se qala ebe sea tima nakong ea maemo a alamo le ha sesebelisoa se tingoa. Ho hloleha ho hong ha lisebelisoa, joalo ka tahlehelo ea matla le bobolu ba firmware, le tsona li tla koala relay.

TLHOKOMELISO: Bakeng sa polokeho e kholo, ho tlameha ho sebelisoe terminal ea liphoso. Relay e sa sireletsehang HA E TLA tsebisa mosebelisi ka liphoso tsohle tse ka bang teng tsa lisebelisoa. Setting e sa sireletsehang e lokeloa ho lumelloa FEELA ho fana ka tšireletso e matlafalitsoeng ha theminale ea phoso E SEBELE ho sebelisoa.

Litlhophiso tsa kamehla tsa feme ho T3A bakeng sa Relay 1 le Relay 2 e sa sireletseha ke Che (E tima).

Haeba sesebelisoa sa phoso se ke ke sa sebelisoa, RKI Instruments e khothaletsa e 'ngoe ea litlhophiso tse latelang:

Lethathamo la 7: Litlhophiso tse khothalelitsoeng bakeng sa Relay Fail-Safe Setting

Mohloli oa Matla
Phepelo ea Matla ka Ntle

Relay Wiring
Tlwaeleho e Tlwaelehileng (NC)

Fail-Sireletsehile
Ho joalo (Bula)

Sephetho
Ts'ebetso e Tloaelehileng: Open Alarm Activation: E koetsoe

Phepelo ea Matla ka Ntle e Tloaelehileng-Buloe (NO)

E (E Buletsoe) Ts'ebetso e Tloaelehileng: Ts'ebetso ea Alamo e Koetsoeng: Bula

Relay 1: Fail-Safe Setting

1. Haeba ho hlokahala, kenya Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ka ho tobetsa le ho tšoara konopo ea MENU bakeng sa metsotsoana e 6.

2. Tobetsa o lokolle konopo ya MENU ho fihlela skrini sa Relay 1 Failsafe se hlaha.

3. Sebelisa li-buttons tsa ADD le SUB ho khetha boemo bo lakatsehang bo sa sireletsehang bakeng sa Relay 1. Khetha "Yes" ho bulela boemo ba ho hlōleha, kapa khetha "Che" ho tlohela boemo bo sa sireletsehang bo tima.
4. Tobetsa konopo ea MENU ho khetha tlhophiso e lakatsehang le ho hatela pele ho Relay 2 hloleha ho seta skrineng.

Buka ea Ts'ebetso ea T3A

Litlhophiso le Tlhophiso ea Sehlahisoa · 37

Relay 2: Fail-Safe Setting
1. Haeba ho hlokahala, kenya Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ka ho tobetsa le ho tšoara konopo ea MENU bakeng sa metsotsoana e 6.
2. Tobetsa o lokolle konopo ya MENU ho fihlela skrini sa Relay 2 Failsafe se hlaha.
3. Sebelisa li-buttons tsa ADD le SUB ho khetha boemo bo lakatsehang bo sa sireletsehang bakeng sa Relay 2. Khetha "Yes" ho bulela boemo ba ho hlōleha, kapa khetha "Che" ho tlohela boemo bo sa sireletsehang bo tima.
4. Sebelisa konopo ea MENU ho tsamaea ka har'a karolo e setseng ea Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ebe u khutlela ho Mokhoa o Tloaelehileng oa Ts'ebetso.
Fault Terminal Fail-Safe Setting
Boitšoaro ba boemo ba Fault Terminal Fail-Safe bo ka fetoloa hore bo sebetse nakong ea phoso kapa bo tima nakong ea phoso. Tlhophiso ea kamehla ke ea ho tima nakong ea phoso, boemo bona bo tlameha ho lokisoa ha feela ho batloa boitšoaro bo fapaneng.
Phoso Terminal: Fail-Safe Setting
1. Haeba ho hlokahala, kenya Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ka ho tobetsa le ho tšoara konopo ea MENU bakeng sa metsotsoana e 6.
2. Tobetsa o lokolle konopo ea MENU ho fihlela skrini sa Fault Terminal Failsafe se hlaha.
3. Sebelisa likonopo tsa ADD le SUB ho khetha boemo bo lakatsehang bo sa sireletsehang bakeng sa Fault Terminal. Khetha "Ee" ho bulela litlhophiso tsa "fall-safe" kapa u khethe "Che" ho tima litlhophiso tse sa atleheng.
4. Sebelisa konopo ea MENU ho tsamaea ka har'a karolo e setseng ea Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ebe u khutlela ho Mokhoa o Tloaelehileng oa Ts'ebetso.

38 · Litlhophiso tsa Sehlahisoa le Tlhophiso

Buka ea Ts'ebetso ea T3A

Mokhoa oa ho lekanya
ELA HLOKO: LEL le CO2 – Skrine sena ha se hlahe ho LEL kapa CO2 liphetolelong tsa T3A hobane lisensara tseo li ka lekanyetsoa feela ho sebelisoa Auto Cal.
HCl - Ho khothaletsoa hore mofuta oa HCl o lokisoe ka Auto Cal, empa Manual Cal e ka sebelisoa ha e ratoa.
AsH3 le HF – Ho kgothaletswa hore mefuta ya ASH3 le HF e lekanyetswe feela ho sebediswa Manual Cal.
Khetho ea mokhoa oa calibration e u lumella ho khetha mokhoa oa ho lekanya karolo ea sensor. Manual Calibration (setting ea fektheri): Sebelisa likonopo tsa ADD le SUB nakong ea likhakanyo ho bapisa 'malo o bontšitsoeng skrineng le boleng ba khase e sebelisoang. Calibration ea Auto: E beha 'malo, ka mor'a nako e reriloeng esale pele, nakong ea ho lekanya boleng bo kentsoeng nakong ea ts'ebetso ea ho lekanya auto. 1. Haeba ho hlokahala, kenya Li-setting tsa Sehlahisoa le menu ea Configuration ka ho tobetsa le ho tšoara
Konopo ea MENU bakeng sa metsotsoana e 6.
2. Tobetsa ebe o lokolla konopo ea MENU ho fihlela skrine ea Cal Method e hlaha.

3. Sebelisa konopo ea ADD ho khetha calibration ka letsoho le konopo ea SUB ho khetha ho lekanya ka bohona.
4. Sebelisa konopo ea MENU ho tsamaea ka har'a karolo e setseng ea Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ebe u khutlela ho Mokhoa o Tloaelehileng oa Ts'ebetso.
Tlhophiso ea Aterese ea Modbus
Modbus ke protocol ea taolo e bulehileng ea indasteri. Modbus e fumaneha ka mefuta e mengata e fapaneng, ho latela mecha ea litaba eo e fetisoang ka eona. Joalo ka liprothokholo tse ngata tsa puisano, Modbus e sebelisa mofuta oa master / moreki. Monghali o romela kopo ea poll bakeng sa tlhahisoleseling ho moreki, moreki o khetha kopo, ebe o romella karabo ka data e batiloeng ho mong'a eona.
Molaetsa oa Modbus o kenyelletsa aterese ea Modbus, eo hangata e bitsoang ID ea yuniti. Aterese ea Modbus e sebelisetsoa ho khetholla aterese ea seva ho marang-rang a RS-485. Seva e 'ngoe le e' ngoe e fuoa aterese 'me e mamela melaetsa e nang le nomoro ena sebakeng sa aterese sa Modbus.
T3A e sebelisa Modbus RTU ea mantlha holim'a sehokelo sa RS-485. RS-485 Modbus e na le liaterese tse 255, ho tloha ho 1 ho ea ho 255. Liaterese tse robeli li sebelisoa bakeng sa litlhophiso tsa tsamaiso ea ka hare, li siea liaterese 1 ho ea ho 247 bakeng sa sesebelisoa sa hau.

Buka ea Ts'ebetso ea T3A

Litlhophiso le Tlhophiso ea Sehlahisoa · 39

Mekhahlelo ea puisano ea RS-485 Modbus e sebelisitsoeng ho T3A ke likotoana tsa data tse 8, ha ho na parity, le 1 stop bit; liparamente tsena li tsitsitse 'me li ke ke tsa fetoloa. Lintlha tsa boleng ba lintlha tse phaphametseng li hlahisoa ka li-byte tsa bohlokoa haholo pele.
Ha o sebelisa Modbus holim'a marang-rang a RS-485, liparamente tsa puisano TŠOANTŠA ho hlophisoa ka nepo bakeng sa lisebelisoa tsohle. Bakeng sa lisebelisoa tse ngata tse sebelisang Modbus, etsa bonnete ba hore ha ho likarolo tse peli tse fuoang aterese e tšoanang. Ho pheta-pheta liaterese ho ka baka liphoso phetisong ea data. Liaterese tsa Modbus li ka abeloa ka tatellano kapa moralo o mong oa aterese o loketseng bakeng sa ho seta marang-rang.
Litlhophiso tsa kamehla tsa feme ho T3A bakeng sa tlhophiso ea aterese ea Modbus ke 1.
1. Haeba ho hlokahala, kenya Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ka ho tobetsa le ho tšoara konopo ea MENU bakeng sa metsotsoana e 6.
2. Tobetsa le ho lokolla konopo ea MENU ho fihlela skrine ea Aterese ea Modbus e hlaha.

3. Sebelisa likonopo tsa ADD le SUB ho eketsa le ho fokotsa nomoro ea aterese ea Modbus, ka ho latellana.
4. Sebelisa konopo ea MENU ho tsamaea ka har'a karolo e setseng ea Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ebe u khutlela ho Mokhoa o Tloaelehileng oa Ts'ebetso.
Modbus Baud Setting
Sekhahla sa baud ke lebelo la data e fetisitsoeng ka har'a sistimi ea Modbus, e lekantsoeng ka likotoana ka motsotsoana (bps). Bakeng sa puisano e atlehileng, boemo ba sekhahla sa baud sa T3A TŠOANTŠE ho lumellana le boemo ba sekhahla sa baud ho molaoli o hokahaneng kapa sesebelisoa se seng sa Modbus. Boemo ba kamehla ba T3A ba Modbus baud ke 9600 bps. Mekhahlelo ea puisano ea RS-485 Modbus e sebelisoang ho T3A ke li-data tse 8, ha ho na parity bit, le 1 stop bit (8-N-1) li-parameter tsena li tsitsitse 'me li ke ke tsa fetoloa. Lisebelisoa tse ling li tla le litefiso tse fapaneng tsa Modbus baud. Sheba le molaoli oa sistimi ea hau ho fumana hore na ho hlokahala maemo a fapaneng a Modbus baud bakeng sa sistimi ea hau. Litlhophiso tsa Modbus baud tse seng li setiloe tse fumanehang bakeng sa T3A ke tse latelang:
· 110bps
· 300bps
· 1200bps
· 2400bps
· 4800bps
· 9600bps

40 · Litlhophiso tsa Sehlahisoa le Tlhophiso

Buka ea Ts'ebetso ea T3A

· 19200 bps 1. Haeba ho hlokahala, kenya Litlhophiso tsa Sehlahisoa le menu ea Configuration ka ho tobetsa le ho tšoara
Konopo ea MENU bakeng sa metsotsoana e 6. 2. Tobetsa o lokolle konopo ya MENU ho fihlela skrine sa Modbus Baud se hlaha.
3. Sebelisa likonopo tsa ADD le SUB ho tsamaisetsa likhethong tse fumanehang tsa Modbus baud. 4. Sebelisa konopo ea MENU ho tsamaea ho pholletsa le Litlhophiso tsa Sehlahisoa le Tlhophiso
menu ebe o khutlela ho Normal Operating Mode.
4-20 mA Offset Litlhophiso
Ho beha 4-20 mA offset ho lumella mosebelisi oa ho qetela ho lekanya tlhahiso ea analog ea sensor. Ha o kenya sesebelisoa, haeba khase e fumanoeng ho T3A e sa tsamaisane le ho balloa ho molaoli, "zero offset" (4 mA) le "fill-scale offset" (20 mA) e ka fetoloa yuniti. Ha nako e ntse e ea, ha lisebelisoa tsa elektroniki li ntse li senyeha ka mokhoa o tloaelehileng, lipotoloho li tla hoholeha. Ho hoholeha hona ho ka baka phapang ho palo ea tlhahiso ea hona joale ke sensor, kapa tekanyong ea hajoale ea molaoli. Haeba ka nako efe kapa efe ho bala ho T3A ha ho sa tšoana le ho bala ho molaoli, 4-20 mA offset e tla hloka ho lekoa bocha. Litlhophiso tsa kamehla tsa feme ho T3A bakeng sa 4-20 mA offset ke 4.00 mA bakeng sa zero offset le 20.00 mA bakeng sa offset e felletseng. 1. Haeba ho hlokahala, kenya Li-setting tsa Sehlahisoa le menu ea Configuration ka ho tobetsa le ho tšoara
Konopo ea MENU bakeng sa metsotsoana e 6. 2. Tobetsa o lokolle konopo ea MENU ho fihlela skrine ea 4-20 mA Offset e hlaha.
3. Tobetsa le ho lokolla konopo ea ADD ho seta 4-20 mA offset le ho fetela skrineng sa zero offset setting. Haeba o sa batle ho seta 4-20 mA offset, tobetsa ebe o lokolla konopo ea SUB kapa MENU ho fetela skrineng sa tlhophiso ea ho bapisa phapang.

Buka ea Ts'ebetso ea T3A

Litlhophiso le Tlhophiso ea Sehlahisoa · 41

Zero Offset Setting
Haeba "E" e khethiloe ho beha 4-20 mA offset:
1. Sebelisa li-buttons tsa ADD le SUB ho eketsa le ho fokotsa zero offset ho unit, ka ho latellana, ho fihlela molaoli a bala 0% / ppm, ho itšetlehile ka mofuta oa khase o fumanoang.
2. Tobetsa konopo ea MENU ho boloka tlhophiso eo u e batlang le ho fetela skrineng se felletseng sa offset.
Boemo bo felletseng ba Offset
ELA HLOKO: Ho lokisa sekheo se felletseng ho tla qala maemo a alamo. Tlosa lialamo kapa u etse bonnete ba hore basebetsi bohle ba tseba hore lialamo leha e le life ke tsa bohata.

1. Sebelisa li-buttons tsa ADD le SUB ho eketsa le ho fokotsa tekanyo e feletseng ea offset, ka ho latellana, ho fihlela molaoli a bala tekanyo e feletseng ea boleng ba mocha oo.
2. Tobetsa konopo ea MENU ho boloka litlhophiso tse lakatsehang le ho fetela skrineng sa tlhophiso ea phapang.
Hlahisa Setlhophiso sa Phapang ea Sekrine
Phapang ea skrini ke phapang ea khanya kapa 'mala o etsang hore litšoantšo tse bontšitsoeng li khethollehe. Ka lebaka la likarolo tse fapaneng tsa kantle, joalo ka khanya ea letsatsi e feteletseng, khanya ea skrini e ka hloka ho lokisoa hore e be ea boleng bo holimo. viewng. Litlhophiso tsa kamehla tsa feme ho T3A bakeng sa phapang ea skrini ke 29, e ka bang 45% ea sekala sa phapang. Litlhophiso tse fapaneng li tloha ho 1 ho isa ho 64.
ELA HLOKO: Ho beha phapang tlase haholo ho tla etsa hore setšoantšo se felloe ke matla kapa se se ke sa bonahala, haholo ha yuniti e le libakeng tse nang le letsatsi le felletseng. Sebaka sa sephetho sa view e ka hlalosoa hampe joalo ka phoso ka har'a sesebelisoa. Etsa bonnete ba ho netefatsa hore konteraka e khethiloeng e ka har'a mefuta e nepahetseng ea viewng.
1. Haeba ho hlokahala, kenya Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ka ho tobetsa le ho tšoara konopo ea MENU bakeng sa metsotsoana e 6.

42 · Litlhophiso tsa Sehlahisoa le Tlhophiso

Buka ea Ts'ebetso ea T3A

2. Tobetsa o lokolle konopo ya MENU ho fihlela skrini sa Contrast se hlaha.

3. Sebelisa likonopo tsa ADD le SUB ho khantša le ho fokotsa phapang, ka ho latellana.
4. Sebelisa konopo ea MENU ho tsamaea ka har'a karolo e setseng ea Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ebe u khutlela ho Mokhoa o Tloaelehileng oa Ts'ebetso.

Khutlela ho Factory Default Settings

Ho khutlisetsa T3A ho litlhophiso tsa eona tsa kamehla tsa feme ho tla hlophisa bocha tlhophiso eohle ea sesebelisoa, ho kenyelletsa le li-zero le li-calibration tsa karolo ea sensor. Boemo ba feme ha bo fetole mofuta oa khase.

Letlapa la 8: Litlhophiso tsa kamehla tsa Sehlahisoa sa T3A le Feme ea Tlhophiso

Tlhophiso
Network ID Zero / Calibration Timer Background Setting Relay 1: Latching/Auto Reset Relay 2: Latching/Auto Reset Relay 1: Fail-Safe Setting Relay 2: Fail-Safe Setting Calibration Method RS-485 Modbus Address Setting RS-485 Modbus Offset Setting4 mA20 MA4 Alarm ea Kopano ea Sensor ea Sensor ea Sensor Element Element Zero Element Calibration Alarm ea Kopano ea Sensor 20 Alamo ea Kopano ea Sensor 1 Keketseho ea Kopano ea Sensor Alarm 1 Setting Sensor Assembly Alarm 2 Keketseho / E Fokotsa Setting

Tlhophiso
5 *E hlakotsoe* 4 Reset Auto Reset No (Off) No (Off) Manual 1 9600 bps 4.00 mA 20.00 mA *E hlakotsoe* *E hlakotsoe* 10% ea Sensor Scale E Eketseha
15% ea Keketseho ea Sensor Scale

1. Haeba ho hlokahala, kenya Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ka ho tobetsa le ho tšoara konopo ea MENU bakeng sa metsotsoana e 6.

Buka ea Ts'ebetso ea T3A

Litlhophiso le Tlhophiso ea Sehlahisoa · 43

2. Tobetsa le ho lokolla konopo ea MENU ho fihlela skrine ea Return to Factory Default e hlaha.

44 · Litlhophiso tsa Sehlahisoa le Tlhophiso

Buka ea Ts'ebetso ea T3A

3. Tobetsa konopo ea ADD ho khutlisetsa sesebelisoa ho li-setting tsa eona tsa kamehla tsa feme le ho fetela pele ho khutlela skrineng sa netefatso ea li-setting tsa feme. Haeba o sa batle ho khutlisetsa sesebelisoa ho li-setting tsa sona tsa feme, tobetsa konopo ea SUB kapa MENU ho tsoela pele ho Seta Bocha skrineng sa Zero & Cal Only.
4. Haeba "E" e khethiloe ho khutlisetsa sesebelisoa ho litlhophiso tsa kamehla tsa feme:
5. Tobetsa konopo ea ADD ho khetha "E" ho netefatsa hore u batla ho tsosolosa sesebelisoa ho litlhophiso tsa eona tsa kamehla tsa fektheri le ho khutlisetsa sesebelisoa ho mokhoa o tloaelehileng oa ho sebetsa. Haeba o sa batle ho tsoela pele ho khutlisetsa sesebelisoa ho li-setting tsa eona tsa feme, tobetsa konopo ea SUB ho khetha "Che" ho tsoela pele ho Seta Sets'oants'o sa Zero & Cal Only.
6. Sebelisa konopo ea MENU ho tsamaea ka har'a karolo e setseng ea Litlhophiso tsa Sehlahisoa le menu ea Tlhophiso ebe u khutlela ho Mokhoa o Tloaelehileng oa Ts'ebetso. TLHOKOMELISO: Haeba T3A e setiloe bocha ho li-setting tsa kamehla tsa feme, mehato TSOHLE ea tlhophiso E TLAMEHA ho phetoa 'me sesebelisoa se TLAMEHA ho emisoa le ho lekanyetsoa bakeng sa ts'ebetso e nepahetseng ea sesebelisoa.
Seta Botjha Maemo a Zero le Maemo
Ho seta bocha li-setting tsa zero le calibration tsa element element ea sensor ho tla lumella li-zero tse bolokiloeng hajoale le boleng ba calibration hore li phomole ntle le ho lokisa litlhophiso tse ling tsohle tsa ts'ebetso joalo ka khetho ea Return to Factory Defaults. 1. Haeba ho hlokahala, kenya Li-setting tsa Sehlahisoa le menu ea Configuration ka ho tobetsa le ho tšoara
Konopo ea MENU bakeng sa metsotsoana e 6. 2. Tobetsa o lokolle konopo ya MENU ho fihlela ho hlaha skrini sa Seta Zero & Calibration Values.
3. Tobetsa konopo ea ADD ho khetha "E" ho seta botjha boleng ba Zero le Calibration le ho fetela Setang Botjha skrine sa netefatso sa Zero & Cal Only. Haeba o sa batle ho seta botjha boleng ba zero le calibration, tobetsa konopo ea SUB ho khetha "Che" ho tsoa ho Litlhophiso tsa Sehlahisoa le menyu ea Litlhophiso le ho khutlisetsa sesebelisoa mokhoeng o tloaelehileng oa ts'ebetso.

Buka ea Ts'ebetso ea T3A

Litlhophiso le Tlhophiso ea Sehlahisoa · 45

4. Haeba "E" e kgethilwe ho seta botjha lefela le boleng ba ho lekanya:
5. Tobetsa konopo ea ADD ho khetha "E" ho netefatsa hore u batla ho tsosolosa litekanyetso tsa Zero le Calibration le ho khutlisetsa sesebelisoa ho mokhoa o tloaelehileng oa ho sebetsa. Haeba o sa batle ho tsoelapele ho seta botjha boleng ba Zero le Calibration, tobetsa konopo ea SUB ho khetha "Che" ho siea Settings ea Sehlahisoa le menu ea Configuration le ho khutlisetsa sesebelisoa mokhoeng o tloaelehileng oa ts'ebetso.
6. Tobetsa o lokolle konopo ea MENU ho khutlela ho Normal Operating Mode. ELA HLOKO: Haeba T3A's bolokoa Zero le Calibration boleng bo seta botjha, sesebediswa SE TSHWANETSE ho zero le ho lekanyetswa bakeng sa tshebetso e nepahetseng le e bolokehileng ya sesebediswa.

46 · Litlhophiso tsa Sehlahisoa le Tlhophiso

Buka ea Ts'ebetso ea T3A

Litlhophiso tsa Ts'ebetso le Calibration
Menu ea Litlhophiso tsa Ts'ebetso e u lumella ho: · etsa tokiso ea zero · etsa phetoho ea nako e telele · fetola litlhophiso tsa alamo ea sensor.
TLHOKOMELISO: Kamora metsotso ea 5 ea ho se sebelisane le sesebelisoa, yuniti e tla khutlela ka mokhoa o tloaelehileng oa ts'ebetso.
TLHOKOMELISO: Lialamo li TLA ke ke tsa sebetsa, leha ho na le khase, ho fihlela u tsoile ho Litlhophiso tsa Ts'ebetso motsotso o le mong.
T3A e tsoela pele ho beha leihlo bakeng sa khase ha e ntse e le ho menu ea Operation Settings.
Ho tima Sensor (20.9% bakeng sa O2)
Mohato oa pele oa ho lekanya ke zeroing (20.9% bakeng sa O2). Ts'ebetso ea zeroing (20.9% bakeng sa O2) E TLAMEHA ho etsoa moeeng o tsebahalang o hloekileng, ho se na litšila kapa likhase tse kotsi tse teng. Haeba boleng ba moea bo ke ke ba tiisetsoa, ​​​​cylinder ea zero air e tla hlokoa ho etsa zero hantle.
Lisebelisoa
· 0.5 LPM e tsitsitseng phallo regulator e nang le knob · senoelo sa calibration · calibration tubing · zero air cylinder (bakeng sa CO2 sensor kapa haeba e se sebakeng sa moea o hloekileng) · 100% N2 cylinder (haeba e senya mochine oa CO2)
TLHOKOMELISO: Kaha ho na le semelo sa CO2 moeeng, hoa hlokahala hore u sebelise silindara e se nang CO2 ha u qeta sensor ea CO2.
1. Ha sehlahisoa se le maemong a tloaelehileng a ts'ebetso, tobetsa konopo ea MENU ho kenya tšebetsong menu ea Operation Settings.

Sensor e seng ea O2
Buka ea Ts'ebetso ea T3A

Senotlolo sa O2
Litlhophiso le Litlhophiso tsa Ts'ebetso · 47

2. Tobetsa konopo ea ADD ho qala ts'ebetso ea zero le ho fetela skrineng se hloekileng sa netefatso ea moea.
3. Haeba sensor e le moeeng o hloekileng, tobetsa konopo ea ADD ho khetha "E" 'me u tsoele pele ho Mohato oa 5. 4. Bakeng sa lisebelisoa tsa CO2 kapa haeba sensor e se moeeng o hlakileng:
a. Haeba ho kentsoe tšireletso ea pula, e lokolle 'me ue tlose kopanong. b. Kenya senoelo sa calibration ntlong ea sensor ea T3A. c. Seketsa selaoli ka har'a silindara ea tekhetlo ea moea ea zero (100% N2 silindara haeba e lenya
CO2 sensor). d. Sebelisa sample tubing ho hokahanya selaolo le senoelo sa calibration. e. Fetola konopo ea regulator ho ea ka nqa ea ho otlo ho bula regulator. f. Lumella khase ho phalla motsotso o le mong. g. Tobetsa konopo ea ADD ho khetha "E" 'me u tsoele pele ho Mohato oa 1. 5. Yuniti e tla qala ts'ebetso ea metsotsoana e 5 ea lefela. Nakong ea zero, ponts'o e tla bonts'a ho bala nako e setseng ho fihlela ts'ebetso e felile. ELA HLOKO: Ts'ebetso ea zero e ke ke ea emisoa ntle le ho khaola motlakase ho
yuniti.
6. Ha ts'ebetso ea zero e phethiloe, tobetsa konopo ea MENU ho ea skrineng sa calibration.
7. Haeba ho ne ho sebelisoa silindara ea zero air calibration (kapa 100% N2 cylinder bakeng sa li-sensors tsa CO2), fetola konopo ea regulator ka ho le letona ho koala selaoli.

48 · Litlhophiso tsa Ts'ebetso le Tekanyetso

Buka ea Ts'ebetso ea T3A

Ho lekanya Sensor (Manual Cal)
Ho tla hlaha skrineng sa Manual Cal kapa Auto Cal, ho ipapisitsoe le hore na Mokhoa oa Calibration o behiloe joang ho Li-setting tsa Sehlahisoa le Menu ea Tlhophiso (sheba leqephe la 39).
ELA HLOKO: LEL le CO2 - LEL le CO2 mefuta ea T3A e ka lekanyetsoa feela ho sebelisoa Auto Cal (sheba karolo e latelang).
HCl - Ho khothaletsoa hore mofuta oa HCl o lokisoe ka Auto Cal, empa Manual Cal e ka sebelisoa ha e ratoa.
U lokela ho lekanya sensor FEELA kamora ho qeta ts'ebetso ea zero.
Kakaretso ea Calibration
Tekanyetso e lokela ho etsoa matsatsing a mang le a mang a mashome a mararo (30). Matsatsi ho tloha ha ho lekanyetsoa ho qetela HA A LOKELA ho feta matsatsi a mashome a robong (90). RKI e khothaletsa hore o lekanye sesebelisoa sa hau khafetsa ho netefatsa ts'ebetso e nepahetseng le sebaka se sireletsehileng sa mosebetsi.
Lisebelisoa
· 0.5 LPM e tsitsitseng phallo regulator e nang le kotola le calibration tubing
TLHOKOMELISO: Haeba ho lekana le Cl2 kapa HCl, ho tlameha ho neheloa molaoli hore a sebelisoe ka khase eo feela. Se ke oa sebelisa selaoli se inehetseng bakeng sa likhase tse ling, haholo-holo H2S.
· senoelo sa calibration · silindara ea calibration kapa jenereithara ea khase (Bakeng sa li-sensor tsa O2, RKI e khothaletsa ho sebelisa 10-18% O2.
Bakeng sa lisensara tse ling kaofela, RKI e khothaletsa ho sebelisa 50% ea boleng bo felletseng ba khase eo u e boneng.)
TLHOKOMELISO: Likhase tse ling tse lemohuoeng li sebelisa likhase tse ling bakeng sa ho lekanya. Likhase tse fumanoeng tse hlokang khase e 'ngoe bakeng sa ho lekanya li thathamisitsoe ka tlase. Haeba o sebelisa khase e 'ngoe bakeng sa ho lekanya, khatello ea khase e 'ngoe e atolositsoeng ho latela lintlha tse thathamisitsoeng ka tlase e lokela ho lekana le 50% ea sekala se felletseng sa khase e bonoang.

Buka ea Ts'ebetso ea T3A

Litlhophiso le Litlhophiso tsa Ts'ebetso · 49

Letlapa la 9: Ligase tsa Tekanyetso ea Likhase

Khase e fumanoeng

Khase ea Tekanyetso ea Surrogate

Ntlha

Arsine (AsH3)

Phospine (PH3)

1.4

Chlorine Dioxide (ClO2)

Chlorine (Cl2)

1

Formaldehyde (CH2O)

Carbon monoxide (CO)

0.2

Hydrogen Fluoride (HF)

Chlorine (Cl2)

7.5

Ozone (O3)

Chlorine (Cl2)

0.8

Nitrogen Dioxide (NO2)

1

Tsamaiso
1. Bakeng sa khase ea EtO calibration: Kopanya tubing ho molaoli, bula molaoli, 'me u lumelle khase hore e phalle metsotso e 1 pele u tsoela pele.
Bakeng sa khase ea calibration ea HCl: Hokela tubing ho regulator, bulela regulator, 'me u lumelle khase ho phalla metsotso e 10 pele u tsoela pele.
2. Haeba u latetse litaelo tse ho Zeroing the Sensor (20.9% bakeng sa O2), skrine e ka tlase e tla hlaha.
Haeba u sebelisa Manual Cal ho tsoa ho Normal Operating Mode, tobetsa MENU habeli.

3. Haeba ho e-na le molebeli oa pula, e lokolle 'me ue tlose kopanong. 4. Kenya senoelo sa calibration ntlong ea sensor ea T3A. 5. Sebelisa sample tubing ho hokahanya selaolo le senoelo sa calibration. 6. Bakeng sa lisilindara tsa khase tse chefo, joalo ka Cl2, ho bohlokoa ho ntša selaoli ha u ntse u se kenya
moqomo. Bula regulator ka ho fetola kotola ka nqane ho oache ebe o e kenya holim'a silindara.
TLHOKOMELISO: Etsa bonnete ba hore u sebelisa sesebelisoa sa ho phefumoloha le ho kenya moea sebakeng seo hantle ha u lekanya ka likhase tse chefo tse ngata.
7. Ka mor'a metsotsoana ea 20-30, qala ho sebelisa li-buttons tsa ADD le SUB ho fetola 'malo ho lumellana le mahloriso a thathamisitsoeng holim'a cylinder ea calibration.

50 · Litlhophiso tsa Ts'ebetso le Tekanyetso

Buka ea Ts'ebetso ea T3A

8. Bakeng sa likhase tsohle tsa calibration ntle le Cl2, ClO2, EtO, le HCl: Tlohela khase ho phalla motsotso o le mong. Bakeng sa khase ea Cl1 ea calibration: Tlohela khase ho phalla metsotso e 2. Bakeng sa khase ea calibration ea ClO3: Tlohela khase ho phalla metsotso e 2. Bakeng sa khase ea calibration ea EtO: Tlohela khase hore e phalle metsotso e 6. Bakeng sa khase ea calibration ea HCl: Tlohela khase ho phalla metsotso e 1.5.
9. Sebelisa likonopo tsa ADD le SUB ho qeta ho lokisa 'malo o hlahang skrineng hore o tsamaisane le mahloriso a thathamisitsoeng holim'a cylinder ea calibration. Bakeng sa li-detectors tse sebelisang khase e 'ngoe, fetola se baloang hore se lumellane le khase e 'ngoe e atisang ho ata ka ntlha e thathamisitsoeng ho Lethathamo la 9 leqepheng la 50. Liphetolelo tse ling li tla tlameha ho behoa ka holimo ho tekanyo e feletseng.
ELA HLOKO: Leha 'malo o sa hloke ho lokisoa hore o tsamaellane le mahloriso a silindara ea calibration, u tlameha ho e lokisa ebe u khutlela tlase ho seta bocha lebala la Cal ho skrine sa Zero/Calibration Timer Information.
10. Ha calibration e phethiloe, tlosa kopi ea calibration ho ntlo ea sensor 'me u khutlisetse molebeli oa pula haeba e tlositsoe Mohato oa 3.
11. Sebelisa konopo ea MENU ho tsamaisetsa skrineng sa Litlhophiso tsa Alamo. Sheba leqephe la 55 bakeng sa litaelo tsa Litlhophiso tsa Alamo.
Ho lekanya Sensor (Auto Cal)
Ho tla hlaha skrineng sa Manual Cal kapa Auto Cal, ho ipapisitsoe le hore na Mokhoa oa Calibration o behiloe joang ho Li-setting tsa Sehlahisoa le Menu ea Tlhophiso (sheba leqephe la 39). U lokela ho lekanya sensor FEELA kamora ho qeta ts'ebetso ea zero.
TLHOKOMELISO: O2 - Haeba u lekana le 100% N2, u tlameha ho sebelisa Manual Cal. Ho lekanya o sebelisa Auto Cal, ho kgothaletswa hore ho be le kgase e pakeng tsa 10 le 18% O2.
AsH3 le HF – Ho kgothaletswa hore mefuta ya ASH3 le HF e lekanyetswe feela ho sebediswa Manual Cal.
Kakaretso ea Calibration
Tekanyetso e lokela ho etsoa matsatsing a mang le a mang a mashome a mararo (30). Matsatsi ho tloha ha ho lekanyetsoa ho qetela HA A LOKELA ho feta matsatsi a mashome a robong (90). RKI e khothaletsa hore o lekanye sesebelisoa sa hau khafetsa ho netefatsa ts'ebetso e nepahetseng le sebaka se sireletsehileng sa mosebetsi.

Buka ea Ts'ebetso ea T3A

Litlhophiso le Litlhophiso tsa Ts'ebetso · 51

Lisebelisoa
· 0.5 LPM e tsitsitseng phallo regulator e nang le kotola le calibration tubing

TLHOKOMELISO: Haeba ho lekana le Cl2 kapa HCl, ho tlameha ho neheloa molaoli hore a sebelisoe ka khase eo feela. Se ke oa sebelisa selaoli se inehetseng bakeng sa likhase tse ling, haholo-holo H2S.
· senoelo sa tekanyo
· Moqomo oa calibration kapa jenereithara ea khase (Bakeng sa li-sensor tsa O2, RKI e khothaletsa ho sebelisa 10-18% O2. Bakeng sa li-sensor tse ling kaofela, RKI e khothaletsa ho sebelisa 50% ea boleng bo felletseng ba khase ea hau e fumanoeng.)

TLHOKOMELISO: Likhase tse ling tse lemohuoeng li sebelisa likhase tse ling bakeng sa ho lekanya. Likhase tse fumanoeng tse hlokang khase e 'ngoe bakeng sa ho lekanya li thathamisitsoe ka tlase. Haeba o sebelisa khase e 'ngoe bakeng sa ho lekanya, khatello ea khase e 'ngoe e atolositsoeng ho latela lintlha tse thathamisitsoeng ka tlase e lokela ho lekana le 50% ea sekala se felletseng sa khase e bonoang.

Letlapa la 10: Ligase tsa Tekanyetso ea Likhase

Khase e fumanoeng

Khase ea Tekanyetso ea Surrogate

Arsine (AsH3) Chlorine Dioxide (ClO2) Formaldehyde (CH2O) Hydrogen Fluoride (HF) Ozone (O3)

Phospine (PH3) Chlorine (Cl2) Carbon Monoxide (CO) Chlorine (Cl2) Chlorine (Cl2) Nitrogen Dioxide (NO2)

Ntlha
1.4 1 0.2 7.5 0.8 1

Tsamaiso
1. Bakeng sa khase ea EtO calibration: Kopanya tubing ho molaoli, bula molaoli, 'me u lumelle khase hore e phalle metsotso e 1 pele u tsoela pele.
Bakeng sa khase ea calibration ea HCl: Hokela tubing ho regulator, bulela regulator, 'me u lumelle khase ho phalla metsotso e 10 pele u tsoela pele.
2. Haeba u latetse litaelo tse ho Zeroing the Sensor (20.9% bakeng sa O2), skrine e ka tlase e tla hlaha.
Haeba u sebelisa Auto Cal ho tsoa ho Normal Operating Mode, tobetsa MENU habeli.

52 · Litlhophiso tsa Ts'ebetso le Tekanyetso

Buka ea Ts'ebetso ea T3A

3. Tobetsa konopo ea ADD ho khetha "Ee" ho qala ts'ebetso ea calibration le ho fetela skrineng sa netefatso ea litekanyo. Haeba u sa batle ho lekanya sensor, tobetsa konopo ea SUB ho khetha "Che" ho fetela skrineng sa li-setting tsa aterese ea seea-le-moea.

4. Tobetsa konopo ea ADD ho khetha "E" ho netefatsa hore u batla ho lekanya kutlo le ho tsoela pele ho skrine sa ho beha mahloriso. Haeba u sa batle ho tsoela pele ho lekanya sensor, tobetsa konopo ea SUB ho khetha "Che" ho fetela skrineng sa li-setting tsa aterese ea seea-le-moea.

5. Sebelisa li-buttons tsa ADD le SUB ho fetola mahloriso ho lumellana le mahloriso a bontšitsoeng holim'a cylinder ea calibration.
Bakeng sa li-detectors tse sebelisang khase e 'ngoe, fetola se baloang hore se tsamaisane le khase e eketsoang ke ntlha e thathamisitsoeng ho Lethathamo la 10 leqepheng la 52.
6. Tobetsa konopo ea MENU ho boloka maemo a mahloriso a khase le ho fetela skrineng sa ho qala litekanyo.

7. Haeba ho kentsoe molebeli oa pula, o qhaqha 'me u o tlose kopanong.
8. Kenya senoelo sa calibration ntlong ea sensor ea T3A.
9. Sebelisa sample tubing ho hokahanya selaolo le senoelo sa calibration.
10. Bakeng sa lisilindara tsa khase tse chefo, joalo ka Cl2, ho bohlokoa ho ntša selaoli ha u ntse u se kenya holim'a cylinder. Bula regulator ka ho fetola kotola ka nqane ho oache ebe o e kenya holim'a silindara.
TLHOKOMELISO: Etsa bonnete ba hore u sebelisa sesebelisoa sa ho phefumoloha le ho kenya moea sebakeng seo hantle ha u lekanya ka likhase tse chefo tse ngata.

Buka ea Ts'ebetso ea T3A

Litlhophiso le Litlhophiso tsa Ts'ebetso · 53

11. Tobetsa konopo ea MENU ho qala ho lekanya kutlo. Yuniti e qala ka bo eona mokhoa oa ho lekanya. Nakong ea ho lekanya, ponts'o e bonts'a ho bala nako e setseng ho fihlela ts'ebetso e felile. Nako ea nako e fapana ho latela mofuta oa khase.
ELA HLOKO: Hang ha nako ea ho bala e qalile, ts'ebetso e ke ke ea emisoa ntle le ho hakolla motlakase ho unit.
12. Ha calibration e phethiloe, tlosa kopi ea calibration ho ntlo ea sensor 'me u khutlisetse molebeli oa pula haeba e tlositsoe Mohato oa 7.
TLHOKOMELISO: Haeba sensor e arabela butle haholo, kapa e sa arabe khase e sebelisitsoeng, e ka bonts'a karolo ea sensor e hlolehileng. Sensor element e tla hloka ho nkeloa sebaka pele e phethela ts'ebetso ea zero le calibration.
13. Fetolela konopo ea regulator ho ea ka nako ea oache ho koala regulator. 14. Sebelisa konopo ea MENU ho tsamaisetsa skrineng sa Litlhophiso tsa Alamo.

54 · Litlhophiso tsa Ts'ebetso le Tekanyetso

Buka ea Ts'ebetso ea T3A

Litlhophiso tsa Alarm ea Sensor
T3A e na le litlhophiso tse peli tsa alamo: Alarm 1 le Alarm 2. Ho sa tsotellehe hore na sesebelisoa se kenyelletsa li-relays tse peli tse omeletseng, litlhophiso tsa alamo ea tsamaiso li fumaneha ho sesebelisoa. Li-alarm set-points kaofela li ka feto-fetoha ho tloha boemong bo tlase haholo ho fihla ho 70% ea khase e felletseng. Alarm 1 set-point HA E LOKELA ho hlophisoa sebakeng se phahameng ho feta Alarm 2 set-point.
Lialamo ka bobeli li ka lokisoa hore li ka sebetsa holima boemo bo ntseng bo eketseha kapa bo fokotsehang ba khase. Setting ea kamehla ea feme ke ho kenya tšebetsong ha khase e bonoang e eketseha ka holimo ho sebaka sa alamo.
Ha khatello ea khase e bonoang ho sensor e kopana kapa e feta Alarm 1 set-point, Alarm 1 indicator LED e tla khantša amber. Ha boemo ba khase bo kopana kapa bo feta Alarm 2 set-point, Alarm 2 indicator LED e tla khantša bofubelu. Letšoao la alamo li-LED li ke ke tsa tima ho fihlela boemo ba khase ho sensor bo theohile ka 10% ka tlase ho li-alarm set-points kapa ho fihlela alamo e hlophisoa bocha sesebelisoa, ho ipapisitse le litlhophiso tsa relay latching / auto reset.
Haeba sesebelisoa se kenyelletsa li-relay tse peli tse omileng tsa khokahano, Relay 1 le Relay 2, litlhophiso tsa Alarm 1 le Alarm 2 li tla laola li-relay tse nang le mehala, ka ho latellana. Ha lisebelisoa tse ka ntle tse tšosang, tse kang mabone a alamo (a bonoang) le manaka (audio) li hokeletsoe sesebelisoa, ha li-sete-point tsa alamo li fihleloa, li-relay li tla kengoa tšebetsong ha li ntse li hokelloa le ho hlophisoa hore li sebetse.
Alamo ea Sensor 1 Setlhophiso
1. Ho tsoa mokhoeng o tloaelehileng oa ts'ebetso, tobetsa o lokolle MENU ho fihlela ho hlaha skrine ea Alarm 1.

2. Sebelisa likonopo tsa ADD le SUB ho eketsa le ho fokotsa Alarm 1 set-point, ka ho latellana.
3. Tobetsa konopo ea MENU ho boloka tlhophiso e lakatsehang le ho fetela pele ho sensor ea Alarm 1 e ntseng e eketseha/e fokotseha skrineng.
Sensor Alarm 1 E eketsa / e Fokotsa Setlhophiso
1. Ho tsoa mokhoeng o tloaelehileng oa ts'ebetso, tobetsa o lokolle MENU ho fihlela Alarm 1 e ntse e eketseha/e fokotseha skrineng sa li-setting.

2. Sebelisa likonopo tsa ADD le SUB ho khetha pakeng tsa ho kenya tšebetsong khase e Kenang kapa e Fokolang, ka ho latellana.

Buka ea Ts'ebetso ea T3A

Litlhophiso le Litlhophiso tsa Ts'ebetso · 55

3. Tobetsa konopo ea MENU ho boloka tlhophiso e lakatsehang le ho fetela skrineng sa li-sensor Alarm 2.
Alamo ea Sensor 2 Setlhophiso
1. Ho tsoa mokhoeng o tloaelehileng oa ts'ebetso, tobetsa o lokolle MENU ho fihlela ho hlaha skrine ea Alarm 2.
2. Sebelisa likonopo tsa ADD le SUB ho eketsa le ho fokotsa Alarm 2 set-point, ka ho latellana. 3. Tobetsa konopo ea MENU ho boloka tlhophiso eo u e batlang le ho fetela pele ho sensor Alarm 2
ho eketsa/fokotsa skrine sa litlhophiso.
Sensor Alarm 2 E eketsa / e Fokotsa Setlhophiso
1. Ho tsoa mokhoeng o tloaelehileng oa ts'ebetso, tobetsa o lokolle MENU ho fihlela Alarm 2 e ntse e eketseha/e fokotseha skrineng sa li-setting.
2. Sebelisa likonopo tsa ADD le SUB ho khetha pakeng tsa ho kenya tšebetsong khase e Kenang kapa e Fokolang, ka ho latellana.
3. Tobetsa konopo ea MENU ho boloka tlhophiso eo u e batlang le ho khutlela ho Normal Operating Mode. TLHOKOMELISO: Lialamo li TLA ke ke tsa sebetsa, leha ho na le khase, ho fihlela u tsoile ho Litlhophiso tsa Ts'ebetso motsotso o le mong. Bakeng sa li-alarms tsa ho tsosolosa likoloi, li-alarms li ke ke tsa tima ho fihlela boemo ba khase ho sensor bo theohile ka 1% ka tlase ho sebaka sa alamo.

56 · Litlhophiso tsa Ts'ebetso le Tekanyetso

Buka ea Ts'ebetso ea T3A

Tlhokomelo
RKI e khothalletsa hore lisebelisoa tsa rona li lekanngoe MINIMUM ea matsatsi a mang le a mang a 90, 'me ka STRONGLY e eletsa hore calibration e etsoe ka matsatsi a mang le a mang a 30. Ntle le ho tseba ts'ebeliso e ikhethileng, sebaka sa kopano ea sensor, ho pepeseha ha khase le lintlha tse ling, k'hamphani e khothaletsa litekanyetso tsa khoeli le khoeli ho nka hore ha ho na tšenyo kapa tšenyo e ka bang teng ho sensor le hore ha ho so be le motlakase.tage ho kopano ea kutlo. Haeba tšenyo e etsahetse kapa matla a fanoeng ho sensor a fetohile, ho lekanya ho lokela ho phethoa hang-hang.
Tlhokomelo e reriloeng e lokela ho kenyelletsa zero le calibration ea sensor (sheba leqephe la 47) le tlhahlobo ea alamo (sheba leqephe la 33).
Hlooho ea sensor e lokela ho bolokoa e se na likaroloana tse tsamaeang le moea, litšila, seretse, sekho webs, litšitšili le likokoanyana, le/kapa maloanlahla afe kapa afe a ka koahelang kapa a koahela kutlo. Ho boloka hlooho ea sensor e hlakile lihloohong tse tsoang linaheng tse ling ho tla lumella ho sebetsa hantle ha sesebelisoa. Tlhahlobo e khutšoane nakong ea tokiso e reriloeng e lokela ho lekana, empa ho ipapisitse le sebaka le tikoloho eo yuniti e kenngoeng ho eona, tlhahlobo ea khafetsa e ka netefatsoa.
T3A e ka 'na ea ameha hampe ke ho pepesehela lintho tse itseng tse tsamaisoang ke moea. Tahlehelo ea kutlo kapa kutu e ka ba butle-butle, haeba lisebelisoa tse joalo li le teng ka bongata bo lekaneng. Ts'ebetso ea sesebelisoa e kanna ea senyeha nakong ea ts'ebetso ka boteng ba lintho tse ka bakang kutu holim'a plating ea khauta. Likhase tse senyang tse sa khaotseng le tse phahameng li ka ba le phello e mpe ea nako e telele bophelong ba tšebeletso ea sehlahisoa. Ho ba teng ha lintho tse joalo sebakeng ha ho thibele tšebeliso ea sesebelisoa sena, empa monyetla oa ho khutsufatsa bophelo ba karolo ea sensor, ka lebaka leo, e lokela ho hlokomeloa. Tšebeliso ea T3A libakeng tsena e ka hloka tlhokomelo e hlophisitsoeng khafetsa ho netefatsa ts'ebetso e sireletsehileng le e tšepahalang ea sistimi.

Ho batle phoso
Tataiso ea ho rarolla mathata e hlalosa matšoao, lisosa tse ka bang teng, le mehato e khothaletsoang bakeng sa mathata ao u ka kopanang le ona ka T3A.

ELA HLOKO: Tataiso ena ea ho rarolla mathata e hlalosa mathata a T3A feela. Sheba bukana ea litaelo bakeng sa mathata ao u ka kopanang le 'ona ho molaoli.

Bothata
F1 Sheba Cable ea Sensor
F4 Sheba Boto ea Sensor

Lethathamo la 11: Melao ea Phoso ea T3A

Sesosa (s)

Tharollo

Boto ea taolo e lahlile puisano le boto ea adaptara ea sensor ea dijithale.

1. Sheba kamano pakeng tsa hlooho ea sehokelo sa ntlo ea sensor le plug-in ea adapter board ea sensor interface ea dijithale.
2. Kenya sebaka sa boto ea adapter ea sensor interface

Boto ea taolo e lahlehetsoe ke commu- 1. Kenya sebaka sa boto ea sebopeho sa sensor. nication le boto ea interface ea sensor.

Buka ea Ts'ebetso ea T3A

Tlhokomelo · 57

Lethathamo la 11: Melao ea Phoso ea T3A

F5 Leka ho Zero Hape

Yuniti ha e ea ka ea sebetsa hantle, ka lebaka la: · ho ba teng ha khase, · phoso ea sensor, kapa · phoso ea boto ea sensor interface.

1. Re-zero sesebelisoa moeeng o hlakileng. 2. Kenya karolo ea sensor. 3. Kenya sebaka sa boto ea sebopeho sa sensor.

F6 Leka ho Lekanya Hape

Yuniti ha ea ka ea sebetsa hantle, ka lebaka la: · ho ba sieo ha khase, · phoso ea kutlo, kapa · phoso ea boto ea sensor interface.

1. Hlalosa bocha karolo ea sensor 'me u netefatse hore khase e teng nakong ea ho lekanya.
2. Kenya karolo ea sensor.
3. Kenya sebaka sa boto ea sebopeho sa sensor.

* Liphoso tsa sistimi li tla kenya tšebetsong terminal ea liphoso sesebelisoa.

Ho fetola Desiccant
T3A e 'ngoe le e' ngoe e tla le mokotla oa desiccant o kentsoeng ka lebokoseng la mateano. Likahare li putsoa ha li omme. Ha desiccant e monya mongobo, e fetoha amber. Nako le nako hlahloba desiccant 'me u e nkele sebaka haeba e fetohile amber.

Ho fetola li-Sensors tsa Mofuta oa Catalytic
RKI e khothaletsa ho khutlisa boto ea sensor element nako le nako ha karabelo e liehang ho khase e bonoa nakong ea ts'ebetso e tloaelehileng ea calibration. Ka mor'a ho nkela boto ea lisebelisoa tsa sensor sebaka, sesebelisoa se LOKELA ho ts'oaroa le ho lekanngoa bakeng sa ts'ebetso e nepahetseng ea sesebelisoa.

TLHOKOMELISO: Se ke oa tlosa sekoaelo sa ntlo ea sensor kapa sekoaelo se koaletsoeng ha lipotoloho li ntse li matlafatsoa ntle le haeba sebaka se ikemiselitse ho se be kotsi. Boloka sekoaelo sa ntlo ea sensor le sekoaelo se koaletsoeng se koetsoe ka thata nakong ea ts'ebetso.

TLHOKOMELISO: Likarolo tse ka hare li ka ba bonolo. E-ba hlokolosi ha u bula lesela le ho tšoara likarolo tsa ka hare. U SE KE UA sebelisa lintho leha e le life tsa tšepe kapa lisebelisoa ho tlosa ntho ea kutlo ho boto ea adapter ea sensor.
1. Tobetsa 'me u tšoare konopo ea SUB metsotsoana e ka bang 6, ho fihlela "OFF" e hlaha skrineng.
2. Hlakola 'me u tlose molebeli oa pula kopanong.

58 · Tlhokomelo

Buka ea Ts'ebetso ea T3A

3. Hlakola 'me u tlose sekoahelo sa ntlo ea sensor ho tloha setsing sa bolulo sa sensor. Beha ka thoko. 4. Hlakola 'me u tlose boto ea khale ea sensor element. Boloka li-screws tse tlositsoeng.

5. Kenya boto e ncha ea sensor element. Netefatsa hore lithakhisa tse botong e ncha ea sensor li hokahana le li-sockets tse holim'a boto ea sensor ea matlo.
6. Sireletsa boto e ncha ea sensor ka li-screw tse tlositsoeng Mohatong oa 4.

Buka ea Ts'ebetso ea T3A

Tlhokomelo · 59

7. Khutlisetsa sekoahelo sa "sensor housing cap" holim'a setsi sa matlo sa sensor, ho etsa bonnete ba hore sekoahelo sa ntlo se tiisitsoe feela ka letsoho.
8. Tobetsa konopo ea ADD ho bulela T3A. 9. Lumella sesebelisoa hore se futhumale metsotso e 10. 10. Zero 'me u lekanye setumo joalo ka ha se hlalositsoe leqepheng la 47.
Ho fetola li-Sensors tsa Mofuta oa Non-Catalytic
RKI e khothaletsa ho nkela karolo ea sensor sebaka neng kapa neng ha karabelo e liehang ho khase e bonoa nakong ea ts'ebetso e tloaelehileng ea calibration. Kamora ho nkela karolo ea sensor sebaka, sesebelisoa se LOKELA ho beoa le ho lekanyetsoa bakeng sa ts'ebetso e nepahetseng ea sesebelisoa. TLHOKOMELISO: Se ke oa tlosa sekoaelo sa sensor ea ntlo kapa sekoaelo se koaletsoeng ha lipotoloho li ntse li le teng
matlafatsoa ntle le haeba sebaka se ikemiselitse hore ha se kotsi. Boloka sekoaelo sa ntlo ea sensor le sekoaelo se koaletsoeng se koetsoe ka thata nakong ea ts'ebetso.
TLHOKOMELISO: Likarolo tse ka hare li ka ba bonolo. E-ba hlokolosi ha u bula lesela le ho tšoara likarolo tsa ka hare. U SE KE UA sebelisa lintho leha e le life tsa tšepe kapa lisebelisoa ho tlosa ntho ea kutlo ho boto ea adapter ea sensor.
1. Tobetsa 'me u tšoare konopo ea SUB metsotsoana e ka bang 6, ho fihlela "OFF" e hlaha skrineng.
2. Haeba ho kentsoe molebeli oa pula, o lokolle 'me u o tlose kopanong. 3. Hlakola 'me u tlose sekoahelo sa ntlo ea sensor ho tloha setsing sa bolulo sa sensor. Beha ka thoko.

60 · Tlhokomelo

Buka ea Ts'ebetso ea T3A

4. Tlosa ka bonolo karolo ea sensor ho boto ea ntlo ea sensor.

5. Hokela ntho e ncha ea sensor ka har'a boto ea sensor ea matlo. Netefatsa hore lithakhisa tse karolong ea sensing li hokahana le li-sockets tse botong ea sensor ea matlo.

6. Khutlisetsa sekoahelo sa "sensor housing cap" holim'a setsi sa matlo sa sensor, ho etsa bonnete ba hore sekoahelo sa ntlo se tiisitsoe feela ka letsoho.

7. Tobetsa konopo ea ADD ho bulela T3A.

8. Lumella mochine o futhumatsang nako e loketseng joalokaha ho bontšitsoe ka tlase, ho itšetlehile ka mofuta oa sensor.

Khase ea ho Khetholla

Nako ea ho futhumatsa

Ammonia (NH3) Arsine (AsH3) Carbon Dioxide (CO2)

Lihora tse 12 lihora tse 2 metsotso e 10

Buka ea Ts'ebetso ea T3A

Tlhokomelo · 61

Khase ea ho Khetholla
Carbon monoxide (CO)

Nako ea ho futhumatsa
Lihora tse 2

Chlorine (Cl2) Chlorine Dioxide (ClO2) Khase e tukang

metsotso e 10

Ethylene oxide (EtO)

Lihora tse 48

Formaldehyde (CH2O) Hydrogen (H2) Hydrogen Chloride (HCl)

Metsotso e 10 lihora tse 2 lihora tse 12

Hydrogen Cyanide (HCN)

Hydrogen Fluoride (HF)

Lihora tse 2

Hydrogen Sulfide (H2S) Nitric Oxide (NO)

Lihora tse 12

Nitrogen Dioxide (NO2) Oxygen (O2) Ozone (O3) Phosphine (PH3) Sulfur Dioxide (SO2)

Lihora tse 2

9. Zero 'me u lekanye setumo joalo ka ha se hlalositsoe leqepheng la 47.

62 · Tlhokomelo

Buka ea Ts'ebetso ea T3A

Ho Fetola Fuse
TLHOKOMELISO: Se ke oa tlosa sekoaelo sa ntlo ea sensor kapa sekoaelo se koaletsoeng ha lipotoloho li ntse li matlafatsoa ntle le haeba sebaka se ikemiselitse ho se be kotsi. Boloka sekoaelo sa ntlo ea sensor le sekoaelo se koaletsoeng se koetsoe ka thata nakong ea ts'ebetso.
TLHOKOMELISO: Likarolo tse ka hare li ka ba bonolo. E-ba hlokolosi ha u bula lesela le ho tšoara likarolo tsa ka hare. U SE KE UA sebelisa lintho leha e le life tsa tšepe kapa lisebelisoa ho tlosa li-fuse.
1. Hakolla kapa tima motlakase ho T3A. 2. Hlakola sekoahelo se kampetsoeng 'me u se behelle ka thōko. 3. Tšoara li-thumbscrews 'me ka bonolo u phahamise tsamaiso ea ka hare ho tsoa ka ntle. E ka phomola
pheletsong ya sebaka se kampetsoeng.
TLHOKOMELISO: Ho khaola sekontiri sa sekontiri ho tloha ntlong ea sensor ho tla lumella ho tlosoa ka ho feletseng ha tsamaiso ea ka hare ho tswa ho sesebelisoa. Ho khaola tsamaiso ea ka hare ho ka fana ka boiketlo ba ho fumana li-terminals tsa boto ea taolo bakeng sa wiring. Hokela hape sehokelo sa sensor pele o kenya sistimi e kahare hape.
4. Fumana fuse e lokelang ho nkeloa sebaka.

5. Hula fuse ea khale ka ho toba. 6. Lumellanya lithakhisa holim'a fuse e ncha le li-sockets tse ka har'a sets'oants'o sa fuse.

Buka ea Ts'ebetso ea T3A

Tlhokomelo · 63

7. Sututsa fuse e ncha ka har'a sets'oants'o sa fuse.
8. Beha tsamaiso ea ka hare ka har'a sebaka se koetsoeng, u bapisa poso e 'ngoe le e' ngoe e ntseng e phahama le leihlo la eona le ts'oaretsoeng ka har'a motheo oa sebaka se kampetsoeng.
9. U sebelisa li-thumbscrews, sutumelletsa ka bonolo ho beha tsamaiso ea ka hare ho li-post posts.
TLHOKOMELISO: Li-thumbscrews tse ho T3A li sebetsa FEELA joalo ka ho ts'oara monoana o motona bakeng sa ho tlosa tsamaiso ea ka hare ho tloha motheong oa sebaka. SE KE UA leka ho lokolla kapa ho tiisa li-thumbcrews ha u bula kapa u koala sebaka se kampetsoeng.
10. Netefatsa hore selikalikoe sa ho tiisa, se lutseng moo ho butsoeng ka khoele ea sebaka se kampetsoeng sa sesebelisoa, se sebakeng se nepahetseng.
11. Sireletsa sekoahelo se kampetsoeng hape.
TLHOKOMELISO: Ha u tiisa sekoahelo sesebelisoa, tiisa sekoaelo ka letsoho FEELA. Ho tiisa sekoahelo ka ho sebelisa lisebelisoa tsa letsoho ho ka baka tšenyo ho O-ring, e ka 'nang ea senya tiiso ea mongobo, e leng se etsang hore ho be le tikoloho e sa sireletsehang.

64 · Tlhokomelo

Buka ea Ts'ebetso ea T3A

Lethathamo la Likarolo

Lethathamo la 12 le thathamisa likarolo le lisebelisoa tsa T3A.
Lethathamo la 12: Lenane la Likarolo

Nomoro ea Karolo
09-0300RK

Tlhaloso
Mokotla oa Desiccant

43-4163

Fuse, 4A

47-5110-5-XX

Cable e nang le sehokelo bakeng sa kit e kentsoeng hole (hlalosa bolelele ka increment ea leoto le 1 ha o odara; bolelele bo boholo bo thathamisitsoe leqepheng la 8), 5-pin

61-2001

Remote sensor mounting kit, 5-pin-proof-proof

66-0001

Sensor, carbon monoxide (CO), ho fihla ho 1,000 ppm sekala se felletseng

66-0002 66-0003-1 66-0003-2 66-0004-1

Sensor, oxygen (O2), 25% volume full scale Sensor, hydrogen sulfide (H2S), bakeng sa ho fihla ho 100 ppm full scale Sensor, hydrogen sulfide (H2S), bakeng sa 200 ho 2,000 ppm full scale Sensor, hydrogen chloride (HCl), ho fihla ho 20 ppm e tletseng.

66-0004-2

Sensor, hydrogen chloride (HCl), ho fihla ho 100 ppm sekala se felletseng

66-0005

Sensor, hydrogen cyanide (HCN), 50 ppm sekala se felletseng

66-0006N-1 66-0006N-2 66-0007

Sensor, ammonia (NH3), ho fihla ho 100 ppm full scale Sensor, ammonia (NH3), bakeng sa 200 ho isa ho 1,000 ppm full scale Sensor, nitric oxide (NO), ho fihla ho 250 ppm sekala se felletseng.

66-0008 66-0009-1 66-0009-2 66-0010 66-0011 66-0012 66-0013 66-0014

Sensor, nitrogen dioxide (NO2), 20 ppm full scale Sensor, ozone (O3), bakeng sa ho fihla ho 5 ppm full scale Sensor, ozone (O3), bakeng sa 10 ho 100 ppm full scale Sensor, sulphur dioxide (SO2), 20 ppm full scale Sensor, formaldehyde scale2Cl10O, full scale ho fihla ho 2 ppm full scale Sensor, chlorine dioxide (ClO20), ho fihla ho 2 ppm full scale Sensor, hydrogen fluoride (HF), 5 ppm full scale

66-0015 66-0016

Sensor, phosphine (PH3), 5 ppm full scale Sensor, ethylene oxide (EtO), ho fihla ho 10 ppm sekala se felletseng

Buka ea Ts'ebetso ea T3A

Lethathamo la Likarolo · 65

Nomoro ea Karolo
66-0039 66-0040 66-0050 66-0051 66-0052 66-0053 66-0054 66-0068 71-0533 81-0002RK-01 81-0002RK-03 81-0004RK-01 81-0004RK-03 81-0007RK-01 81-0010RK-01 81-0010RK-03 81-0012RK-01 81-0012RK-03 81-0013RK-01 81-0013RK-05 81-0064RK-01 81-0064RK-03 81-0069RK-01 81-0069RK-03 81-0070RK-01 81-0070RK-03 81-0072RK-01

Lethathamo la 12: Lenane la Likarolo
Tlhaloso
Sensor, hydrogen (H2), 100% LEL full scale Sensor, combustible type, catalytic type, 100% LEL full scale Sensor, carbon dioxide (CO2), mofuta oa IR, 5.0% volume full scale Sensor, combustible gas (CH4), mofuta oa IR, 100% LEL full scalestible4 IR, volume 100, 100% LEL full scalestible IR full scale Sensor, combustible gas (HC), mofuta oa IR, 2% LEL full scale Sensor, carbon dioxide (CO5,000), 3 ppm full scale Sensor, arsine (AsH1.00), 3 ppm full scale T2A Operator's Manual (tokomane ena) Calibration% cylinder hydrogen, hydrogen cylinder% 50 air cylinder 34% hydrogen cylinder Calibration cylinder, 2% volume (50% LEL) hydrogen in air, 103 litre Calibration cylinder, 50% LEL propane in air, 34 litre steel Calibration cylinder, 50% LEL propane in air, 103 litre Calibration cylinder, 15% LEL cylinder 34, 10% LEL 5000 litre, LEL 34% LEL (10 ppm) methane in air, 5000 litre steel Calibration cylinder, 103% LEL (50 ppm) methane in air, 34 litre Calibration cylinder, 50% LEL methane in air, 103 litre steel Calibration cylinder, 50 liter methane cylinder, 34 airter, 50 litres le LL 58% volume methane in nitrogen, 50 litre steel Calibration cylinder, 34% volume methane in nitrogen, 50 litre Calibration cylinder, 103 ppm CO in air, 200 litre steel Calibration cylinder, 34 ppm CO in air, 200 litre Calibration 103 airlippm 2000 litre cylinder 2 airlippm silindara, 34 ppm CO moeeng, 2000 litre Calibration cylinder, 2 ppm CO103 ka naetrojene, 2.5 lithara ea tšepe Calibration cylinder, 2 ppm CO34 ka naetrojene, XNUMX litre Calibration cylinder, XNUMX% COXNUMX lithareng moeeng, XNUMX lithara ea COXNUMX moeeng, lithara

66 · Lethathamo la Likarolo

Buka ea Ts'ebetso ea T3A

Nomoro ea Karolo
81-0072RK-03 81-0076RK 81-0076RK-01 81-0076RK-03 81-0078RK-01 81-0078RK-03 81-0146RK-02 81-0149RK-02 81-0149RK-04 81-0150RK-02 81-0150RK-04 81-0151RK-02 81-0151RK-04 81-0170RK-02 81-0170RK-04 81-0174RK-02 81-0176RK-02 81-0176RK-04 81-0180RK-02 81-0180RK-04 81-0181RK-02 81-0181RK-04 81-0185RK-02 81-0185RK-04 81-0190RK-02 81-0190RK-04 81-0192RK-02

Lethathamo la 12: Lenane la Likarolo
Tlhaloso
Calibration cylinder, 2.5% CO2 moeeng, 103 litre Zero air calibration cylinder, 17 litre Zero air calibration cylinder, 34 litre steel Zero air calibration cylinder, 103 litre Calibration cylinder, 100% nitrogen, 34 nitrogen 100 cylinder 103% Calinder 200 lithara litre Calibration cylinder, 2 ppm H58S in nitrogen, 5 litre Calibration cylinder, 2 ppm H58S in nitrogen, 5 litre Calibration cylinder, 2 ppm H34S in nitrogen, 10 litre aluminium Calibration cylinder, 2 nitrogenS 58 litres 10 ppm H2S 34 ppm H25S ka naetrojene, 2 litre aluminium Calibration cylinder, 58 ppm H25S ka nitrogen, 2 litre Calibration cylinder, 34 ppm H5S ka nitrogen, 2 litre aluminium Calibration cylinder, 58 ppm SO5 ka nitrogen nitrogen 2 liter, SO34 ka nitrogen 50 litre, SO3 naetrojene, 58 litre aluminium Calibration cylinder, 25 ppm NH3 in nitrogen, 58 litre Calibration cylinder, 25 ppm NH3 in nitrogen, 34 litre Calibration cylinder, 10 ppm NH2 in nitrogen, 58 litre aluminium Calibration, NO10 litre aluminium Calibration, NO2 litre 34 Calibration cylinder, 25 ppm NO58 in nitrogen, 25 litre aluminium Calibration cylinder, 34 ppm NO in nitrogen, 0.5 litre Calibration cylinder, 3 ppm NO in nitrogen, 58 litre aluminium Calibration cylinder, 0.5 ppm nitrogen, 3 ppm 34 ppm 5 ppm PH2 ho naetrojene, 58 litre aluminium Calibration cylinder, 5 ppm Cl2 ho naetrojene, 34 litre Calibration cylinder, 2 ppm Cl2 ka nitrogen, 58 litre aluminium Calibration cylinder, XNUMX ppm ClXNUMX ka nitrogen litre, XNUMX

Buka ea Ts'ebetso ea T3A

Lethathamo la Likarolo · 67

Lethathamo la 12: Lenane la Likarolo

Nomoro ea Karolo

Tlhaloso

81-0192RK-04 81-0194RK-02

Calibration cylinder, 2 ppm Cl2 in nitrogen, 34 liter aluminium Calibration cylinder, 10 ppm HCl ho nitrogen, 58 litre

81-0196RK-02

Calibration cylinder, 10 ppm HCN ka nitrogen, 58 litre

81-0196RK-04

Calibration cylinder, 10 ppm HCN ka naetrojene, 34 lithara ea aluminium

81-1050RK

Regulator e nang le gauge le knob, 0.5 LPM, bakeng sa li-cylinders tsa lithara tse 17 le tse 34 tsa tšepe (lisele tse nang le likhoele tsa kantle)

81-1051RK

Regulator e nang le gauge le knob, 0.5 LPM, bakeng sa aluminium ea lithara tse 34, lithara tse 58, le li-cylinders tsa calibration tsa lithara tse 103 (lisele tse nang le likhoele tse ka hare)

81-1183

Komiki ea calibration e nang le li-tubes tse 3 tsa maoto

81-1184

Sesireletsi sa pula (se rometsoe ka li-detectors tsa O2, CO, H2S, CO2, le LEL feela)

81-9029RK-02 81-9029RK-04 81-9062RK-04

Calibration cylinder, 100 ppm NH3 in N2, 58 litre Calibration cylinder, 100 ppm NH3 in N2, 34 lithara ea aluminium Calibration cylinder, 5 ppm EtO moeeng, 34 lithara ea aluminium

81-9090RK-01 81-9090RK-03 82-0101RK

Calibration silindara, 12% O2 ho N2, 34 litha e le nngwe tšepe Calibration silindara, 12% O2 ho N2, 103 litha e le nngwe Magnetic wand

Z2000-CAPFILTER Teflon filter bakeng sa kopano ea matlo a sensor (bakeng sa mefuta eohle ea khase ntle le Cl2, ClO2, le NH3)

68 · Lethathamo la Likarolo

Buka ea Ts'ebetso ea T3A

Sehlomathiso A: 4-20 mA Letšoao

Sehlomathiso sena ke selelekela feela. Boitsebiso bo lokela ho sebetsa e le tlhaloso e khutšoanyaneview ea 4-20 mA mats'oao a mats'oao a hona joale a lupu 'me ha ea lokela ho nkuoa e le tšupiso e felletseng bakeng sa ts'ebetsong kapa ts'ebeliso e nepahetseng.
Maemo a indasteri a mabapi le 4-20 mA mats'oao a hona joale a loop le likarolo tse ling tsa lisebelisoa tsa elektroniki ho nahanoa hore a tsejoa ke setsebi. Bakeng sa khokahanyo e nepahetseng ho molaoli kapa Programmable Logic Controller (PLC), sheba bukana ea tataiso e khethehileng ea moetsi kapa litaelo tsa sesebelisoa seo.

Fetileview

Ha o sebelisa lisebelisoa tsa 4-20 mA tse hlahisoang ka marang-rang, 4-20 mA e hlalosa sebaka sa hona joale sa li-analoge tsa loop, ka 4 mA e emelang qetello e tlaase ka ho fetisisa le 20 mA e phahameng ka ho fetisisa. Kamano lipakeng tsa loop ea hajoale le boleng ba khase e mela. Ho feta moo, T3A e sebelisa litekanyetso tse ka tlase ho 4 mA ho bontša maemo a khethehileng a boemo, joalo ka ha ho bontšitsoe ka tlase:

Lethathamo la 13: 4-20 mA Ranges

Hona joale
2 mA 3 mA 3.5 mA

Boemo ba Mofuputsi
Sensor Fault Sensor ho Menu Mode Sensor e ntse e lekanyetsoa

4 mA e lumella molaoli ea amohelang / PLC ho khetholla pakeng tsa lets'oao la zero, terata e robehileng, kapa sesebelisoa se sa arabeleng. Melemo ea kopano ea 4-20 mA ke hore: maemo a indasteri, a theko e tlase ho a sebelisa, a ka hana mefuta e meng ea lerata la motlakase, mme lets'oao ha le fetole boleng ho potoloha "loop" (ho fapana le vol.tage). Advan ea bohlokoatage ea loop ea hona joale ke hore ho nepahala ha lets'oao ha ho amehe ke matla a ka bang tengtagke ho theola mohala o hoketsoeng. Leha ho na le khanyetso e kholo moleng, loop ea hajoale ea T3A e tla boloka motlakase o nepahetseng bakeng sa sesebelisoa, ho fihlela bophahamo ba eona bo phahameng.tage bokgoni.
Ke boemo bo le bong feela bo ka bang teng ka nako efe kapa efe. Sesebelisoa se seng le se seng se sebetsang ka lets'oao la 4-20 mA hona joale la loop se tlameha ho hokelloa ka mohala ka kotloloho ho molaoli. Li-unit tse kentsoeng ka har'a tlhophiso ea ketane ea daisy bakeng sa lets'oao la sejoale-joale la 4-20 mA li ke ke tsa fetisetsa likhokahano tsa data ho molaoli hantle.

Lipalo

I(4-20) = Hona joale ea loop, e lekantsoeng ka boleng ba mA = ppm (kapa %) ea tekanyo ea mahloriso ea khase = tekanyo e feletseng ea kutlo

Buka ea Ts'ebetso ea T3A

Sehlomathiso A: 4-20 mA Letšoao · 69

Lethathamo la 14: Mekhahlelo ea Sensor Element Scale

Mofuta oa Sensor
Electrochemical (EC) Electrochemical (EC) Electrochemical (EC) Electrochemical (EC) Electrochemical (EC) Electrochemical (EC) Electrochemical (EC) Electrochemical (EC) Electrochemical (EC) Electrochemical (EC) Electrochemical (EC) Electrochemical (EC) Electrochemical (EC) Electrochemical (EC) Electrochemical (IR) Electrochemical (IR) Catalytic Bead (CB2)

Mofuta oa Khase
Hydrogen Sulfide Hydrogen Sulfide (High Range) Sulfur Dioxide Oxygen Carbon Monoxide Chlorine Hydrogen Chloride Ammonia Ammonia (Medium Range) Ammonia (High Range) Hydrogen Chlorine Dioxide Hydrogen Cyanide Nitrogen Dioxide Phosphine Carbon Dioxide Combustible Gas Combustible Gas

Foromo
H2S H2S2K SO2 O2 CO CL2 HCL NH3 NH3300 NH3A H2 CLO2 HCN NO2 PH3 CO2 LEL LEL

Range
0-100 ppm 0-2000 ppm 0-20 ppm 0-25% 0-1000 ppm 0-20 ppm 0-30 ppm 0-100 ppm 0-300 ppm 0-1000 ppm 0-4% ppm molumo 0-1 ppm 0-50 0-20 ppm 0-5% 0-5% LEL 0-100% LEL

Maemo a sebele a ka fapana ho ea ka sehlahisoa sa rona. Bakeng sa lipotso tse fetang tlhahisoleseling le litaelo tse fanoeng, ikopanye le moemeli oa thekiso ea sehlahisoa sena bakeng sa thuso.

70 · Sehlomathiso A: 4-20 mA Letšoao

Buka ea Ts'ebetso ea T3A

Ho lekanya Hona Jwale
Haeba boleng bo lekantsoeng ke 0 mA, joale: lithapo tsa loop li robehile, kopano ea sensor ha e sebelisoe, kopano ea sensor ha e sebetse hantle, kapa molaoli ha a sebetse. Metara e mengata ea dijithale (DMM), kapa mitha ea hajoale, e ka sebelisoa hammoho le molaoli le/kapa ho leka lets'oao la 4-20 mA la loop hajoale. Ho metha hona joale, beha li-probes tsa metara ho latela loop ea hajoale.

Buka ea Ts'ebetso ea T3A

Sehlomathiso A: 4-20 mA Letšoao · 71

Sehlomathiso B: Lipuisano tsa Modbus
Balaoli ba RKI ba na le bokhoni ba ho amohela likenyelletso tsa sensor ea Modbus bakeng sa likhokahano tsa data le li-detectors tsa letoto la T3A. Modbus ke protocol ea puisano e sebelisang khokahano ea serial ea RS-485, 'me e ka amohela lisebelisoa tse ngata tse fapaneng.
Ho itšetlehile ka mofuta oa potoloho e sebelisoang, ho na le moeli oa hore na ke lisebelisoa tse kae tse ka kopanngoang le marang-rang a sensor ea Modbus. Hajoale balaoli ba RKI ba lumella lisebelisoa tse ngata tsa 64 marang-rang a le mong. Lintlha li fetisetsoa marang-rang a Modbus ka mokhoa o itseng oa Modbus baud, kapa lebelo la lebelo. Leha a le manyane, marang-rang a nang le lisebelisoa tse ngata tse hokahaneng a tla baka tieho e nyane, e leka-lekaneng phetisong ea data.
Litlhophiso tsa Wiring
Ketane ea daisy ke sekema sa likhoele moo lisebelisoa tse ngata li hokeloang hammoho ka tatellano, kapa ka selikalikoe. Liketane tsa Daisy li ka sebelisoa bakeng sa matla, matšoao a analog, data ea dijithale, kapa motsoako oa eona. Bakeng sa merero ea T3A, lentsoe daisy chain le bolela lisebelisoa tse ngata tse hokahaneng ka letoto ho etsa mohala o le mong o molelele oa lisebelisoa, tse hokahaneng ka mekhoa ea likhoele tse kentsoeng ka har'a sesebelisoa ka seng.
Twisted pair cabling ke mofuta oa lithapo tseo ho tsona li-conductors tse peli tsa potoloho e le 'ngoe li sothehang hammoho ka sepheo sa ho hlakola tšitiso ea motlakase (EMI) mehloling e kantle hammoho le "crosstalk" lipakeng tsa lipara tse haufi. Ho elektronike, crosstalk ke ketsahalo efe kapa efe eo pontšo e fetisitsoeng ho potoloho e le 'ngoe kapa mocha oa tsamaiso ea phetisetso e baka phello e sa batleheng ho potoloho e' ngoe kapa mocha. T3A e hloka lipara tse sothehileng bakeng sa likhokahano tsohle tsa Modbus tse nang le mehala.
Lithapo tse sothehileng li atisa ho sireletsoa molemong oa ho thibela EMI ho ea pele. Electromagnetic shielding e fana ka tšitiso e tsamaisang motlakase ho fokotsa maqhubu a motlakase kantle ho thebe mme e fana ka tsela ea conduction eo maqhubu a susumetsoang a ka tsamaisoang le ho khutlela mohloling, ka khokahano ea litšupiso tsa fatše. Lithapo tsena li bitsoa shielded twisted pairs (STP) 'me li khothaletsoa libakeng tsa ts'ebetso tse nang le lerata le phahameng.
Khokahano e Loketseng
Sebaka sa khokahano ea Modbus ho tloha sesebelisoa sa ho lemoha khase ho molaoli se ke ke sa feta maoto a 4,000. Mohlala oa lisebelisoa tse nang le ketane ea daisy, sena se sebetsa ho sensor ea ho qetela e amanang le mohala. Bohole ba khokahanyo ba maoto a 100, kapa ka tlase ho moo, bo hloka terata ea 22 ho isa ho 24 gauge. Libaka tsa khokahanyo tse fetang maoto a 100 li hloka terata ea 18 ho isa ho 20.

72 · Sehlomathiso B: Modbus Communications

Buka ea Ts'ebetso ea T3A

Bakeng sa tlhaiso-leseling e batsi mabapi le ho kenya marang-rang a marang-rang a lisebelisoa tsa Modbus hantle, sheba setšoantšo se latelang.

Mohala oa lets'oao oa yuniti ka 'ngoe o mathela setsing sa matšoao sa sensor ea boahelani. Ka sesebelisoa se seng le se seng se kopantsoeng le sesebelisoa se fetileng ka mohala oa pontšo, "ketane" e bōptjoa, e nang le sesebelisoa sa pele sa ketane se amanang ka ho toba le molaoli.

Letlapa la 15: RS-485 Modbus Connection Distances bakeng sa Wiring ea Motlakase

Bolelele ba Bohole

Khutšoane

<100 Maoto

Bolelele bo mahareng*

Maoto a 101 ho isa ho Maoto a 1,000
Maoto a 1,000 ho isa ho Maoto a 4,000

Boholo ba Gauge
22 ho isa ho 24 Gauge
18 ho isa ho 20 Gauge
18 ho isa ho 20 Gauge

Lipara Tse Sothehileng
E sirelelitsoe, libakeng tsa lerata le phahameng E sirelelitsoe, libakeng tsa lerata le phahameng E sirelelitsoe, libakeng tsa lerata le phahameng

(*) Mohanyetsi oa ho felisa o ka hlokahala bakeng sa sesebelisoa sa ho qetela sa ketane ea daisy.

Buka ea Ts'ebetso ea T3A

Sehlomathiso B: Puisano ea Modbus · 73

Sehlomathiso C: 'Mapa oa Ngoliso ea Modbus

Ngolisa Aterese (Hex)
1 3 4 5 6 7 8 9 BCE 10 16 17 18

Ngolisa Aterese (Dec)
1 3 4 5 6 7 8 9 11 12 14 16 22 23 24

Tlhaloso ea Lintlha
Aterese ea Modbus ea ho Bala Khase Setsi sa Mofuta oa Khase Mofuta o Moholo oa Tokiso e Nyane ea Sensor Voltage Ho bala Fault Code Sensor Type Relay 1 Setting Relay 2 Setting Precision Relay Setting Days Ho tloha ho Zero ea ho Qetela

19

25

Mofuta oa Calibration

1A

26

Boleng ba Boikemisetso

1C

28

Matsatsi a Ho Fetela

Tekanyetso

1E

30

Relay 1 State

1F

31

Relay 2 State

20

32

Relay 1 Reset

21

33

Relay 2 Reset

R/W Length Unit Likarabo tse Loketseng

R

2

PHAPAMISA Palo ea Khase ea Numere

R

1

UINT 0 247

R

1

ENUM 0 26, sheba ka tlase

R

1

ENUM 0 1, sheba ka tlase

R

1

UINT 0 100

R

1

UINT 0 9

R

1

ENUM 0 7, sheba ka tlase

R

2

FLOAT 12V 35V

R

1

ENUM 0 6, sheba ka tlase

R

1

ENUM 0-4, sheba ka tlase

R

2

FLOAT 1 32000

R

2

FLOAT 1 32000

R

1

INT

0 3

R

1

BFLD Bona Lethathamo la Litlhophiso tsa Relay

R

1

UINT 0 60000

(> 60000) Ka tloaelo ho "Le ka mohla"

R

1

ENUM 0 1

R

2

PHAPAMISA Palo ea Khase ea Numere

R

1

UINT 0-60000

(> 60000) Ka tloaelo ho "Le ka mohla"

R

1

INT

0 Relay Ha e sebetse

1 Relay e sebetsa

R

1

INT

0 Relay Ha e sebetse

1 Relay e sebetsa

R/W

1

INT

Bala joalo ka 0

Ngola 1 ho seta bocha Relay 1 state

R/W

1

INT

Bala joalo ka 0

Ngola 1 ho seta bocha Relay 2 state

· Ngolisa Aterese 1: Linomoro tsa Hexadecimal · Ngolisa Aterese 2: Linomoro tsa Decimal · R/W: Bala/Ngola data e nang le bokhoni · R: Lintlha tse baloang feela · FLOAT: Nomoro ea ntlha e phaphametseng

· ENUM: Palo · UINT: Nomoro e sa saenang · INT: Palo kaofela · BFLD: Bit Field · (*): E lekantsoe ka ho nepahala

74 · Sehlomathiso C: 'Mapa oa Ngoliso ea Modbus

Buka ea Ts'ebetso ea T3A

T3A Modbus Ngoliso Linotlolo tsa Palo ea MAP

Ngolisa Aterese ea 4: Mofuta oa Khase

Karabo
0 1 2 3 4 5 6 7 9 10 12 13 14 15 16 17 18 26 27 28 29 30

Mofuta oa Khase
H2S Hydrogen Sulfide SO2 Sulfur Dioxide O2 Oxygen CO Carbon Monoxide CL2 Chlorine CO2 Carbon Dioxide LEL Combustible Gas VOC Volatile Organic Compounds HCL Hydrogen Chloride NH3 Ammonia CLO2 Chlorine Dioxide HCN Hydrogen Hydrogen Cyanide H2OFdrogen F2 – Fluorine Formaldehyde NO2 Nitrogen Dioxide O3 – Ozone PH3 Phosphine HBr Hydrogen Bromide EtO Ethylene Oxide CH3SH Methyl Mercaptan AsH3 – Arsine

Ngolisa Aterese ea 5: Mofuta oa Yuniti

Karabo
0 1

Mofuta oa Yuniti
ppm %

Ngolisa Aterese ea 8: Mokhoa oa Sensor

Karabo
0 1 2 3 5 6 7

Mokhoa oa kutlo
Mokhoa o Tloaelehileng oa Ts'ebetso Mokhoa oa ho Lekanya Alamo Mode oa Tlhahlobo ea Mokhoa oa Ts'ebetso o Hateletseng oa Boemo ba Taolo.

Buka ea Ts'ebetso ea T3A

Sehlomathiso C: 'Mapa oa Ngoliso ea Modbus · 75

Ngolisa Aterese B/11: Khoutu ea Phoso

Karabo
0 1
4
5 6

Mofuta oa Phoso
Ha ho Tahlehelo ea Phoso ea Puisano le Boto ea Sensor Tahlehelo ea Puisano le Sensor Element/Housing Zero Error Calibration Phoso

Ngolisa Aterese C/12: Mofuta oa Sensor

Karabo
0 1 2 4

Mofuta oa Sensor
EC Electrochemical IR Infrared CB Catalytic Bead PID Photo Ionization Detector

Ngodisa Aterese 17/23: Relay Setting

Bit Relay Setting

Mosebetsi

5 Relay 2: Keketseho/ Ho fokotseha Setlhophiso

0 E fokotseha 1 - E ea eketseha

4 Relay 1: Keketseho/ Ho fokotseha Setlhophiso

0 E fokotseha 1 - E ea eketseha

3 Relay 2: Failsafe Setting

0 Che (E tima)

1 Ee (Bula)

2 Relay 1: Failsafe Setting

0 Che (E tima)

1 Ee (Bula)

1 Relay 2: Latch/Auto Reset 0 Auto Reset

1 - Latch

0 Relay 1: Latch/Auto Reset 0 Auto Reset

1 Latch

Ngolisa Aterese 19/25: Mofuta oa Calibration

Karabo
0 1

Mofuta oa Calibration
Manual Calibration Auto Calibration

76 · Sehlomathiso C: 'Mapa oa Ngoliso ea Modbus

Buka ea Ts'ebetso ea T3A

Litokomane / Lisebelisoa

RKI LITŠOANTŠISO T3A Sensor Transmitter [pdf] Buka ea Taelo 66-6302-25, 66-6307-25, 66-6312-10, 66-6314-10, 66-6308-20, 66-6304, 66-6368-01, 66-6303, 66-6301-66 Tr. Transmitter, T6313A, Sensor Transmitter, Transmitter

Litšupiso

• Bukana ea Mosebelisi