LATTICE HW-USBN-2B Programming Cables
Tlhahisoleseding ya Sehlahiswa
Litlhaloso
- Lebitso la Sehlahisoa: Lisebelisoa tsa Lenaneo
- Tataiso ea basebelisi: FPGA-UG-02042-26.7
- Letsatsi la ho tsoa: Mmesa 2024
Litaelo tsa Tšebeliso ea Sehlahisoa
Likaroloana
Lithapo tsa lenaneo li fana ka mesebetsi ea bohlokoa bakeng sa lisebelisoa tsa programmable tsa Lattice. Mesebetsi e ikhethileng e ka fapana ho latela sesebelisoa se khethiloeng.
Lisebelisoa tsa mananeo
Lithapo tsa lenaneo li etselitsoe ho hokela sesebelisoa se shebiloeng molemong oa ho etsa mananeo. Ba thusa ho fetisa le ho laola matšoao pakeng tsa software ea lenaneo le sesebelisoa se ka etsoang.
Programming Cable Pin Litlhaloso
Lisebelisoa tsa cable tsa lenaneo li na le mesebetsi e khethehileng e lumellanang le likarolo tsa lenaneo la lisebelisoa tsa Lattice programmable. Mona ke tse ling tsa litlhaloso tsa senotlolo:
- VCC TDO/SO: Lenaneo la Moqtage – Sephetho sa Lintlha tsa Teko
- TDI/SI: Kenyelletso ea Lintlha tsa Teko - Output
- ISPEN/PROG: Numella – Output
- TRST: Hlahisa Teko Botjha – Output
- E QETILE: Kenyo - HO FEDILE e bontsha boemo ba tlhophiso
- TMS: Mokhoa oa Teko - Sephetho
- GND: Fatše – Kenyo
- TCK/SCLK: Kenyo ya Tshupanako ya Teko - Sephetho
- INIT: Qala – Kenya
- Lipontšo tsa I2C: SCL1 le SDA1 - Output
- 5 V OUT1: 5 V Letšoao la tlhahiso
*Tlhokomeliso: Lihokelo tsa Flywire li ka hlokahala bakeng sa JTAG mananeo.
Programming Cable In-System Programming Interface
Cable ea programming e hokahana le PC e sebelisa likhoele tse khethehileng bakeng sa phetiso le taolo ea data. Sheba lipalo tse fanoeng bakeng sa likabelo tse felletseng tsa phini.
Lipotso Tse Botsoang Hangata
- Q: Ke software efe e khothalletsoang ho etsa mananeo ka likhoele tsee?
- A: Ho khothalletsoa ho sebelisa software ea Diamond Programmer/ispVM System bakeng sa ho etsa mananeo ka likhoele tsena.
- P: Na ke hloka li-adapter tse ling bakeng sa ho hokahanya likhoele ho PC ea ka?
- A: Ho ipapisitse le sebopeho sa komporo ea hau, u ka hloka adaptara e ts'oanang ea boema-kepe bakeng sa khokahano e nepahetseng.
Boithorollo
Lattice ha e fane ka tiisetso, boemeli, kapa tiisetso mabapi le ho nepahala ha tlhahisoleseding e teng tokomaneng ena kapa ho tšoaneleha ha lihlahisoa tsa eona bakeng sa morero ofe kapa ofe. Lintlha tsohle tse mona li fanoe JOALOKAHA, ka liphoso tsohle, 'me likotsi tsohle tse amanang le tsona ke boikarabello ba Moreki ka botlalo. Tlhahisoleseding e fanoeng mona ke ea merero ea tlhahisoleseding feela mme e ka 'na ea e-ba le liphoso tsa tekheniki kapa tse sieo,' me e ka 'na ea etsoa e sa nepahalang ka mabaka a mangata, 'me Lattice ha e na boikarabelo ba ho ntlafatsa kapa ho lokisa kapa ho fetola boitsebiso bona. Lihlahisoa tse rekisoang ke Lattice li tlas'a liteko tse fokolang, 'me ke boikarabello ba Moreki ho tseba hore na lihlahisoa life kapa life li lokela ho sebetsa le ho etsa liteko le ho netefatsa hore li joalo. LIHLAHISO LE LITŠEBELETSO TSA LATTICE HA LIA qaptjoa, HO ETSOA, KAPA HO LEKELETSOA HO SEBELISA BOPHELO KAPA LITSAMAISO TSA TŠEBELETSO TSA BOHLOKOA, LITIKOLOHO TSE KOTSI, KAPA LITIKOLOHO TSE LING TSE HLOKA HO HLOKAHALA-HO SIRELETSEHLENG E MOR'A HO SEBELISA MOSEBETSI OA FEELA, MAHALA LE HO SEBELISA TŠEBELETSO E MAHALA. KGOTSA TŠEBELETSO E KA LEBISA LEFU, HO LETSA MOTHO, TŠENYEHO E KHALE HAHOLO KAPA TŠEBELETSO EA TIKOLOHO (KA KELETSO, “LITŠEBELETSO TSE KOTSI”). HO FETA HO FIHLELA HO FETA, MOREKI O TLAMEHA HO NKA MEHATO E BOHLOKO HO SIRELETSA MAHALA A SEHLAHISO LE TŠEBELETSO, HO kenyeletsoa HO FANA KA LITLHOKOMELISO TSE NEPAHETSENG, LITŠOANTŠISO TSE HLOLELANG, LE/KGOTSA HO TSWALA MESEBETSI. LATTICE E HLOKOMELA KA HO BONAHALA TIISETSO EFE KAPA E FELENG KAPA E NAHANANG EA HO SEBELISA LIHLAHISO KAPA LITŠEBELETSO BAKENG SA TŠEBELISO E KOTSI E KHOLO. Tlhahisoleseding e fanoeng tokomaneng ena ke ea mong'a Lattice Semiconductor, 'me Lattice e na le tokelo ea ho etsa liphetoho leha e le life tlhahisoleseding e tokomaneng ena kapa lihlahisoa leha e le life ka nako leha e le efe ntle le tsebiso.
Likaroloana
- Ts'ehetso bakeng sa lihlahisoa tsohle tse hlophisitsoeng tsa Lattice
- 2.5 V to 3.3 V I2C programming (HW-USBN-2B)
- 1.2 V ho 3.3 VJTAG le mananeo a SPI (HW-USBN-2B)
- 1.2 V ho 5 VJTAG le SPI programming (lithapo tse ling kaofela)
- E loketse bakeng sa prototyping ea moralo le ho lokisa liphoso
- Hokela ho li-interfaces tse ngata tsa PC
- USB (v.1.0, v.2.0)
- PC Parallel Port
- Lihokelo tsa mananeo tse fumanehang habonolo
- Lihokelo tse fapaneng tsa flywire, 2 x 5 (.100”) kapa 1 x 8 (.100”)
- 6 maoto (limithara tse 2) kapa ho feta tsa bolelele ba thapo ea lenaneo (PC ho ea DUT)
- Kaho e lumellanang le lead-free/RoHS
Lisebelisoa tsa mananeo
Lihlahisoa tsa Cable tsa Lattice Programming ke khokahano ea hardware bakeng sa lenaneo la in-system la lisebelisoa tsohle tsa Lattice. Kamora hore mosebelisi a phethe moralo oa logic mme a thehe lenaneo file ka Lattice Diamond®/ispLEVER® Classic/Radiant lisebelisoa tsa ntlafatso, mosebelisi a ka sebelisa Diamond/Radiant Programmer kapa software ea ispVM™ System ho hlophisa lisebelisoa ka sekepeng. Software ea ispVM System/Diamond/Radiant Programmer e iketsetsa litaelo tse nepahetseng tsa lenaneo, liaterese tsa mananeo le data ea mananeo e ipapisitseng le tlhaiso-leseling e bolokiloeng lenaneong. file le litekanyetso tse behiloeng ho Diamond/Radiant Programmer/ispVM System. Lits'oants'o tsa mananeo li hlahisoa ho tsoa ho USB kapa koung e ts'oanang ea PC ebe li tsamaisoa ka thapo ea lenaneo ho ea sesebelisoa. Ha ho na likarolo tse ling tse hlokahalang bakeng sa lenaneo.
Tlhokomeliso: Port A ke ea JTAG mananeo. Radiant programming software e ka sebelisa thapo e hahelletsoeng ka har'a hub ea USB ho PC, e lemohang thapo ea ts'ebetso ea USB ho Port A. Ha Port B e le ea phihlello ea UART/I2C.
Software ea Diamond Programmer/Radiant Programmer/ispVM System e kenyellelitsoe le lihlahisoa tsohle tsa meralo ea Lattice 'me e fumaneha bakeng sa ho khoasolla ho tsoa ho Lattice. web site at www.latticesemi.com/programmer.
Programming Cable Pin Litlhaloso
Mesebetsi e fanoeng ke lithapo tsa lenaneo li lumellana le mesebetsi e fumanehang ho lisebelisoa tse ka khonehang tsa Lattice. Kaha lisebelisoa tse ling li na le likarolo tse fapaneng tsa lenaneo, mesebetsi e khethehileng e fanoang ke thapo ea lenaneo e ka itšetleha ka sesebelisoa se khethiloeng. ispVM System/Diamond/Radiant Programmer software e iketsetsa mesebetsi e nepahetseng ho latela sesebelisoa se khethiloeng. Sheba Lethathamo la 3.1 bakeng sa ho fetaview ea mesebetsi ea cable ea programming.
Lethathamo la 3.1. Programming Cable Pin Litlhaloso
| Programming Cable Pin | Lebitso | Mofuta oa Pin ea Cable ea Lenaneo | Tlhaloso |
| VCC | Lenaneo la Moqtage | Kenyeletso | Kopana le VCCIO kapa VCCJ sefofane sa sesebelisoa se shebiloeng. ICC e tloaelehileng = 10 mA. Boto ea sepheo
e fana ka VCC phepelo/referense bakeng sa thapo. |
| TDO/SO | Sephetho sa Lintlha tsa Teko | Kenyeletso | E sebelisoa ho fetisa data ka IEEE1149.1 (JTAG) maemo a lenaneo. |
| TDI/SI | Kenyeletso ya Boitsebiso | Sephetho | E sebelisoa ho fetola data ka mokhoa oa IEEE1149.1 oa lenaneo. |
| ISPEN/PROG | Thusa | Sephetho | Etsa hore sesebelisoa se hlophisehe.
E boetse e sebetsa joalo ka SN/SSPI Chip Select bakeng sa mananeo a SPI ka HW-USBN-2B. |
| TRST | Hlakola Botjha | Sephetho | Ho ikhethela IEEE 1149.1 mochini oa ho qala bocha. |
| QETILE | QETILE | Kenyeletso | HO QETILE e bontša boemo ba tlhophiso |
| TMS | Mokhoa oa Teko Khetha Kenyo | Sephetho | E sebelisoa ho laola mochini oa mmuso oa IEEE1149.1. |
| GND | Fatše | Kenyeletso | Hokela ho sefofane sa fatše sa sesebelisoa se shebiloeng |
| TCK/SCLK | Kenyeletso ea Oache | Sephetho | E sebelisoa ho ts'oara mochini oa mmuso oa IEEE1149.1 |
| MOEKETSI | Qala | Kenyeletso | E bontša hore sesebelisoa se se se loketse ho qala. INITN e fumaneha feela lisebelisoa tse ling. |
| I2C: SCL1 | I2C SCL | Sephetho | E fana ka I2C pontšo ea SCL |
| I2C: SDA1 | I2C SDA | Sephetho | E fana ka I2C pontšo ea SDA. |
| 5 V TSOA1 | 5 V Tsoa | Sephetho | E fana ka letšoao la 5 V bakeng sa iCEprogM1050 Programmer. |
Hlokomela:
- E fumaneha feela thapong ea HW-USBN-2B. Boemakepe ba mananeo ba Nexus™ le Avant™ I2C ha bo sebetse
*Hlokomela: Software ea Lattice PAC-Designer® ha e tšehetse ho etsa mananeo ka lithapo tsa USB. Ho hlophisa lisebelisoa tsa ispPAC ka likhoele tsena, sebelisa software ea Diamond Programmer/ispVM System.
*Tlhokomeliso: HW7265-DL3, HW7265-DL3A, HW-DL-3B, HW-DL-3C le HW-DLN-3C ke lihlahisoa tse lekanang le mosebetsi.
- Ela hloko: Bakeng sa litšupiso, sehokelo sa 2 x 10 ho HW7265-DL2 kapa HW7265-DL2A se lekana le Tyco 102387-1. Sena se tla hokahanya le li-header tse tloaelehileng tsa 100-mil 2 x 5, kapa 2 x 5 keyed, sehokelo sa banna se khutlisitsoeng joalo ka 3M N2510-5002RB.
Lenaneo la Software
Diamond/Radiant Programmer le ispVM System bakeng sa lisebelisoa tsa Classic ke sesebelisoa se ratoang sa software bakeng sa lisebelisoa tsohle tsa Lattice le likhoele tsa ho jarolla. Mofuta oa morao-rao oa Lattice Diamond/Radiant Programmer kapa software ea ispVM System e teng bakeng sa ho khoasolla ho tsoa ho Lattice. web site at www.latticesemi.com/programmer
Litlhahiso tsa Moralo oa Boto e Lebeletsoeng
Sehanyetsi sa ho hula sa 4.7 kΩ se khothaletsoa khokahanong ea TCK ea boto e shebiloeng. Ts'ebetso ena ea ho theola e khothaletsoa ho qoba ho ts'oara ka mokhoa o sa lebelloang ha molaoli oa TAP o susumetsoang ke lioache tse potlakileng kapa joalo ka VCC r.amps holimo. Ts'ebetso ena e khothaletsoa bakeng sa malapa ohle a hlophisitsoeng a Lattice.
Lipontšo tsa I2C SCL le SDA ke li-drain tse bulehileng. Sehanyetsi sa ho hula sa 2.2 kΩ ho VCC se hlokahala botong e shebiloeng. Ke boleng ba VCC feela ba 3.3 V le 2.5 V bakeng sa I2C tse tšehetsoang ke lithapo tsa HW-USBN-2B.
Bakeng sa malapa a lisebelisoa tsa Lattice a nang le matla a fokolang, ho kgothaletswa ho eketsa sehanyetsi sa 500 Ω pakeng tsa VCCJ le GND nakong ea nako ea lenaneo ha thapo ea lenaneo la USB e hokahane le moralo o tlase haholo oa boto ea matla. Ho na le FAQ e buang ka sena ka botebo ho: http://www.latticesemi.com/en/Support/AnswerDatabase/2/2/0/2205
Leano la JTAG Lebelo la boema-kepe ba mananeo le kanna la hloka ho laoloa ha o sebelisa likhoele tsa mananeo tse hoketsoeng ho li-PCB tsa bareki. Sena se bohlokoa haholo ha ho na le routing e telele ea PCB kapa ka lisebelisoa tse ngata tse tlanngoeng ka ketane. Software ea lenaneo la Lattice e ka fetola nako ea TCK e sebelisitsoeng ho JTAG kou ea mananeo ho tsoa ho thapo. Boemo bona ba boema-kepe bo nepahetseng bo tlase ba TCK bo ipapisitse le lintlha tse ngata, ho kenyelletsa lebelo la PC le mofuta oa thapo e sebelisitsoeng (port e bapileng, USB kapa USB2). Sesebelisoa sena sa software se fana ka khetho ea ho liehisa TCK bakeng sa debugging kapa libaka tse lerata. Ho na le FAQ e buang ka sena ka botebo ho: http://www.latticesemi.com/en/Support/AnswerDatabase/9/7/974.aspx
Mohala oa ho khoasolla oa USB o ka sebelisoa ho hlophisa Power Manager kapa lihlahisoa tsa ispClock ka software ea lenaneo la Lattice. Ha o sebelisa thapo ea USB ka lisebelisoa tsa Power Manager I, (POWR604, POWR1208, POWR1208P1), mosebelisi o tlameha ho lieha ho etsa TCK ka ntlha ea A FAQ e teng e tšohlang sena ka botebo ho: http://www.latticesemi.com/en/Support/AnswerDatabase/3/0/306.aspx
Lenaneo la Flywire le Reference Connection
Sheba ho Lethathamo la 6.1 ho tsebahatsa, ho latela sesebelisoa sa Lattice, mokhoa oa ho hokela li-flywires tse fapaneng tsa lenaneo la Lattice. JTAG, likou tsa tlhophiso tsa SPI le I2C li khetholloa ka mokhoa o hlakileng. Lithapo tsa khale le li-hardware li kenyelelitsoe bakeng sa litšupiso. Ho feta moo, litlhophiso tse fapaneng tsa lihlooho li thathamisitsoe.
Lethathamo la 6.1. Reference Pin le Cable
| HW-USBN-2B
'Mala oa Flywire |
TDI/SI | TDO/SO | TMS | TCK/SCLK | ISPEN/PROG | QETILE | TRST(OUTPUT) | VCC | GND | I2C: SCL | I2C: SDA | 5 V Tsoa |
| namunu | Brown | Bopherese | Bosoeu | Bosehla | Boputsoa | Botala | Khubedu | Ntsho | Bosehla/Bosweu | Botala/Bosweu | Khubedu/Tsweu | |
| HW-USBN-2A
'Mala oa Flywire |
TDI | TDO | TMS | TCK | ispEN/PROG | MOEKETSI | TRST(OUTPUT)/E QETILE(INPUT) | VCC | GND |
na |
||
| namunu | Brown | Bopherese | Bosoeu | Bosehla | Boputsoa | Botala | Khubedu | Ntsho | ||||
| HW-DLN-3C
'Mala oa Flywire |
TDI | TDO | TMS | TCK | ispEN/PROG |
na |
TRST(OUTPUT) | VCC | GND | |||
| namunu | Brown | Bopherese | Bosoeu | Bosehla | Botala | Khubedu | Ntsho | |||||
|
Keletso ea Boto ea Boipheliso ea Lenaneo la mofuta oa Cable |
Sephetho | Kenyeletso | Sephetho | Sephetho | Sephetho | Kenyeletso | Kenyeletso/Sehlahisoa | Kenyeletso | Kenyeletso | Sephetho | Sephetho | Sephetho |
| — | — | 4.7 kΩ Hula-Holimo | 4.7 kΩ Hula-Fatše |
(Tlhaloso ea 1) |
— | — |
(Tlhaloso ea 2) |
— | (Tlhaloso ea 3)
(Tlhaloso ea 6) |
(Tlhaloso ea 3)
(Tlhaloso ea 6) |
— | |
| Hokela lithapo tsa thapo tsa lenaneo (ka holimo) ho sesebelisoa se tsamaellanang kapa li-header pins (ka tlase). | ||||||||||||
JTAG Lisebelisoa tsa Port
| ECP5™ | TDI | TDO | TMS | TCK |
Lihokelo tsa boikhethelo ho sesebelisoa ispEN, PROGRAM, INITN, DONE le/kapa TRST matšoao (Hlalosa ho litlhophiso tsa Custom I/O ho ispVM System kapa software ea Diamond Programmer. Ha se lisebelisoa tsohle tse nang le liphini tsena) |
Ho hlokahala | Ho hlokahala | — | — | — |
| LatticeECP3™/LatticeECP2M™ LatticeECP2™/LatticeECP™/ LatticeEC™ |
TDI |
TDO |
TMS |
TCK |
Ho hlokahala |
Ho hlokahala |
— |
— |
— |
|
| LatticeXP2™/LatticeXP™ | TDI | TDO | TMS | TCK | Ho hlokahala | Ho hlokahala | — | — | — | |
| LatticeSC™/LatticeSCM™ | TDI | TDO | TMS | TCK | Ho hlokahala | Ho hlokahala | — | — | — | |
| MachXO2™/MachXO3™/MachXO3D™ | TDI | TDO | TMS | TCK | Ho hlokahala | Ho hlokahala | — | — | — | |
| MachXO™ | TDI | TDO | TMS | TCK | Ho hlokahala | Ho hlokahala | — | — | — | |
| ORCA®/FPSC | TDI | TDO | TMS | TCK | Ho hlokahala | Ho hlokahala | — | — | — | |
| ispXPGA®/ispXPLD™ | TDI | TDO | TMS | TCK | Ho hlokahala | Ho hlokahala | — | — | — | |
| ispMACH® 4000/ispMACH/ispLSI® 5000 | TDI | TDO | TMS | TCK | Ho hlokahala | Ho hlokahala | — | — | — | |
| MACH®4A | TDI | TDO | TMS | TCK | Ho hlokahala | Ho hlokahala | — | — | — | |
| ispGDX2™ | TDI | TDO | TMS | TCK | Ho hlokahala | Ho hlokahala | — | — | — | |
| ispPAC®/ispClock™ (Tlhokomeliso 4) | TDI | TDO | TMS | TCK | Ho hlokahala | Ho hlokahala | — | — | — | |
| Platform Manager™/Motsamaisi oa Matla/Motsamaisi oa Matla II/Motsamaisi oa Sethala II (Tlhokomeliso 4) | TDI |
TDO |
TMS |
TCK |
Ho hlokahala |
Ho hlokahala |
— |
— |
— |
|
CrossLink™-NX/Certus™-NX/ CertusPro™-NX/Mach™-NX/MachXO5™-NX |
TDI |
TDO |
TMS |
TCK |
Lihokelo tsa boikhethelo ho sesebelisoa ispEN, PROGRAMN,
INITN, DONE le/kapa TRST matšoao (Hlalosa ho litlhophiso tsa Custom I/O ho ispVM System kapa software ea Diamond Programmer. Ha se lisebelisoa tsohle tse nang le liphini tsena) |
Ho hlokahala |
Ho hlokahala |
— |
— |
— |
||
| HW-USBN-2B
'Mala oa Flywire |
TDI/SI | TDO/SO | TMS | TCK/SCLK | ISPEN/PROG | QETILE | TRST(OUTPUT) | VCC | GND | I2C: SCL | I2C: SDA | 5 V Tsoa |
| namunu | Brown | Bopherese | Bosoeu | Bosehla | Boputsoa | Botala | Khubedu | Ntsho | Bosehla/Bosweu | Botala/Bosweu | Khubedu/Tsweu | |
| HW-USBN-2A
'Mala oa Flywire |
TDI | TDO | TMS | TCK | ispEN/PROG | MOEKETSI | TRST(OUTPUT)/E QETILE(INPUT) | VCC | GND |
na |
||
| namunu | Brown | Bopherese | Bosoeu | Bosehla | Boputsoa | Botala | Khubedu | Ntsho | ||||
| HW-DLN-3C
'Mala oa Flywire |
TDI | TDO | TMS | TCK | ispEN/PROG |
na |
TRST(OUTPUT) | VCC | GND | |||
| namunu | Brown | Bopherese | Bosoeu | Bosehla | Botala | Khubedu | Ntsho | |||||
|
Keletso ea Boto ea Boipheliso ea Lenaneo la mofuta oa Cable |
Sephetho | Kenyeletso | Sephetho | Sephetho | Sephetho | Kenyeletso | Kenyeletso/Sehlahisoa | Kenyeletso | Kenyeletso | Sephetho | Sephetho | Sephetho |
|
— |
— |
4.7 kΩ
Ts'oara |
4.7 kΩ Hula-Fatše |
(Tlhaloso ea 1) |
— |
— |
(Tlhaloso ea 2) |
— |
(Tlhaloso ea 3)
(Tlhaloso ea 6) |
(Tlhaloso ea 3)
(Tlhaloso ea 6) |
— |
|
| Hokela lithapo tsa thapo tsa lenaneo (ka holimo) ho sesebelisoa se tsamaellanang kapa li-header pins (ka tlase). | ||||||||||||
Lisebelisoa tsa Port SPI tsa Makhoba
| ECP5 | MOSI | MISO | — | EA-CCLK | SN |
Likhokahano tsa boikhethelo ho sesebelisoa sa PROGRAMN, INITN le/kapa DONE matshwao |
Ho hlokahala | Ho hlokahala | — | — | — | |
| LatticeECP3 | MOSI | MISO | — | EA-CCLK | SN | Ho hlokahala | Ho hlokahala | — | — | — | ||
| MachXO2/MachXO3/MachXO3D | SI | SO | — | EA-CCLK | SN | Ho hlokahala | Ho hlokahala | — | — | — | ||
|
CrossLink LIF-MD6000 |
MOSI |
MISO |
— |
SPI_SCK |
SPI_SS |
Khetha. CDONE |
CRESET_B |
Ho hlokahala |
Ho hlokahala |
— |
— |
— |
| iCE40™/iCE40LM/iCE40 Ultra™/ iCE40 UltraLite™ |
SPI_SI |
SPI_SO |
— |
SPI_SCK |
SPI_SS_B |
Khetha. CDONE |
CRESET_B |
Ho hlokahala |
Ho hlokahala |
— |
— |
— |
|
CrossLink-NX/Certus-NX/CertusPro-NX |
SI |
SO |
— |
LEKHOTLA |
SCSN |
Khetha.Kgetha HO ETSA | — |
Ho hlokahala |
Ho hlokahala |
— |
— |
— |
Lisebelisoa tsa boema-kepe tsa I2C
| Lisebelisoa tsa boema-kepe tsa I2C | ||||||||||||
| MachXO2/MachXO3/MachXO3D | — | — | — | — |
Likhokahano tsa boikhethelo ho sesebelisoa sa PROGRAMN, INITN le/kapa DONE matshwao |
Ho hlokahala | Ho hlokahala | SCL | SDA | — | ||
| Motsamaisi oa Sethala II | — | — | — | — | Ho hlokahala | Ho hlokahala | SCL_M + SCL_S | SDA_M + SDA_S | — | |||
| L-ASC10 | — | — | — | — | — | — | — | Ho hlokahala | Ho hlokahala | SCL | SDA | — |
|
CrossLink LIF-MD6000 |
— |
— |
— |
— |
— |
Khetha. CDONE |
CRESET_B |
Ho hlokahala |
Ho hlokahala |
SCL |
SDA |
— |
Lihlooho
| 1 x 10 conn (lithapo tse fapaneng) | 3 | 2 | 6 | 8 | 4 | 9 kapa 10 | 5 kapa 9 | 1 | 7 | — | — | — |
| 1 x 8 khoa | 3 | 2 | 6 | 8 | 4 | — | 5 | 1 | 7 | — | — | — |
| 2 x 5 khoa | 5 | 7 | 3 | 1 | 10 | — | 9 | 6 | 2, 4, kapa 8 | — | — | — |
Baetsi ba mananeo
| Setšoantšo sa 300 | 5 | 7 | 3 | 1 | 10 | — | 9 | 6 | 2, 4, kapa 8 | — | — | — |
| iCEprog™ iCEprogM1050 | 8 | 5 | — | 7 | 9 | 3 | 1 | 6 | 10 | — | — | 4 (Tlhokomeliso 5) |
Lintlha:
- Bakeng sa lisebelisoa tsa khale tsa Lattice ISP, ho hlokahala 0.01 μF decoupling capacitor ho ispEN/ENABLE ea boto e shebiloeng.
- Bakeng sa HW-USBN-2A/2B, boto e shebiloeng e fana ka matla - Tloaelehileng ICC = 10 mA. Bakeng sa lisebelisoa tse nang le phini ea VCCJ, VCCJ e tlameha ho hokeloa ho VCC ea thapo. Bakeng sa lisebelisoa tse ling, hokela VCCIO ea banka e loketseng ho VCC ea thapo. Ho hlokahala 0.1 μF decoupling capacitor ho VCCJ kapa VCCIO haufi le sesebelisoa. Ka kopo, sheba leqephe la lintlha tsa sesebelisoa ho fumana hore na sesebelisoa se na le phini ea VCCJ kapa hore na banka ea VCCIO e laola sebaka seo u batlang ho se etsa (sena se kanna sa se tšoane le sefofane sa VCC/VSS sa sesebelisoa se shebiloeng).
- Bula mats'oao a drain. Boto e shebiloeng e tlameha ho ba le ~2.2 kΩ hug-up resistor e hoketsoeng sefofaneng se le seng seo VCC e hoketsoeng ho sona. Lithapo tsa HW-USBN-2B li fana ka likhoele tsa ka hare tsa 3.3 kΩ ho VCC.
- Ha u sebelisa software ea PAC-Designer® ho hlophisa lisebelisoa tsa ispPAC kapa ispClock, u se ke ua hokela TRST/DONE.
- Haeba u sebelisa thapo ea khale ho feta HW-USBN-2B, hokela +5 V phepelo ea kantle lipakeng tsa iCEprogM1050 pin 4 (VCC) le pin 2 (GND).
- Bakeng sa HW-USBN-2B, ke boleng ba VCC feela ba 3.3 V thru 2.5 V bo tšehetsoeng bakeng sa I2C.
Ho hokela Cable ea Programming
Boto e shebiloeng e tlameha ho se be le matla ha e hokela, e khaoha, kapa e hokela hape mohala oa lenaneo. Kamehla hokela phini ea thapo ea GND (terata e ntšo) pele o hokela JTAG likhohlopo. Ho hloleha ho latela lits'ebetso tsena ho ka baka tšenyo ho sesebelisoa se hlophisehang.
Lenaneo la Cable TRST Pin
Ho hokela phini ea TRST le thapo ea TRST ha ho khothalletsoe. Ho e-na le hoo, hokela phini ea TRST ho Vcc. Haeba boto ea TRST pin e hoketsoe ho thapo ea TRST pin, laela ispVM/Diamond/Radiant Programmer ho khanna TRST pin holimo.
Ho lokisa ispVM/Diamond/Radiant Programmer ho khanna pini ea TRST holimo:
- Kgetha aetheme ya menu ya Dikgetho.
- Khetha Cable le I/O Port Setup.
- Khetha lebokose la tlhahlobo la TRST/Reset Pin-Connected.
- Kgetha konopo ya Set High radio.
Haeba khetho e nepahetseng e sa khethoa, pinana ea TRST e tsamaisoa tlase ke ispVM/Diamond/Radiant Programmer. Ka lebaka leo, ketane ea BSCAN ha e sebetse hobane ketane e notletsoe sebakeng sa RESET.
Lenaneo la Cable ispEN Pin
Lithako tse latelang li lokela ho hlophisoa:
- Pini ea BSCAN ea lisebelisoa tsa 2000VE
- ENABLE pin of MACH4A3/5-128/64, MACH4A3/5-64/64 and MACH4A3/5-256/128 devices.
Leha ho le joalo, mosebelisi o na le boikhethelo ba ho ba le lithapo tsa BSCAN le ENABLE tse tsamaisoang ke phini ea ispEN ho tsoa thapong. Tabeng ena, ispVM/Diamond/Radiant Programmer e tlameha ho hlophisoa ho khanna phini ea ispEN tlase ka tsela e latelang:
Ho lokisa ispVM/Diamond/Radiant Programmer ho khanna pin ea ispEN tlase:
- Kgetha aetheme ya menu ya Dikgetho.
- Khetha Cable le I/O Port Setup.
- Kgetha lebokoso la ho hlahloba le hokahantsweng ke Pin/BSCAN.
- Khetha konopo ea Set Low radio.
E 'ngoe le e' ngoe ea li-cable ea mananeo e tsamaisana le likhokahano tse peli tse nyane tse thusang ho boloka li-flywires li hlophisehile. Moetsi le karolo ea karolo e latelang ke mohloli o le mong oa lihokelo tse lekanang:
- 1 x 8 Sehokelo (bakeng sa mohlalaample, Samtec SSQ-108-02-TS)
- 2 x 5 Sehokelo (bakeng sa mohlalaample, Samtec SSQ-105-02-TD)
Flywire kapa lihlooho tsa thapo li reretsoe ho hokela lihloohong tse tloaelehileng tsa sebaka sa 100-mil (lithapo tse arohaneng ka 0.100 inch). Lattice e khothaletsa hlooho e bolelele ba lisenthimithara tse 0.243 kapa 6.17 mm. Leha ho le joalo, lihlooho tsa bolelele bo bong li ka sebetsa hantle ka ho lekana.
Ho Odara Boitsebiso
Lethathamo la 10.1. Programming Cable Feature Summary
| Sebopeho | HW-USBN-2B | HW-USBN-2A | HW-USB-2A | HW-USB-1A | HW-DLN-3C | HW7265-DL3, HW7265-DL3A, HW-DL-3B,
HW-DL-3C |
HW7265-DL2 | HW7265-DL2A | PDS4102-DL2 | PDS4102-DL2A |
| USB | X | X | X | X | — | — | — | — | — | — |
| PC-Parallel | — | — | — | — | X | X | X | X | X | X |
| 1.2 V Tšehetso | X | X | X | — | — | — | — | — | — | — |
| 1.8 V Tšehetso | X | X | X | X | X | X | — | X | — | X |
| 2.5-3.3 V
Tšehetso |
X | X | X | X | X | X | X | X | X | X |
| 5.0 V Tšehetso | — | X | X | X | X | X | X | X | X | X |
| 2 x 5 Sehokedi | — | X | X | X | X | X | X | X | — | — |
| 1 x 8 Sehokedi | X | X | X | X | X | — | — | X | X | |
| Flywire | X | X | X | X | X | X | — | — | — | — |
| Kaho e se nang loto | X | X | — | — | X | — | — | — | — | — |
| E fumaneha bakeng sa odara | X | — | — | — | X | — | — | — | — | — |
Tafole ea 10.2. Ho laela tlhahisoleseling
| Tlhaloso | Ho Odara Nomoro ea Karolo | Tikoloho ea China ea RoHS- Nako ea Tšebeliso e Setsoalle (EFUP) |
| Cable ea lenaneo (USB). E na le thapo ea USB ea 6′, likhokahanyo tsa flywire, adaptara ea boemo ba 8 (1 x 8) le adaptara ea maemo a 10 (2 x 5), e se nang loto, kaho e lumellanang le RoHS. | HW-USBN-2B | 
|
| Lenaneo la cable (PC feela). E na le adaptara ea port e bapileng, thapo ea 6′, likhokahanyo tsa flywire, adaptara ea boemo ba 8 (1 x 8) le adaptara ea maemo a 10 (2 x 5), e se nang loto, kaho e lumellanang le RoHS. | HW-DLN-3C |
Tlhokomeliso: Lithapo tsa tlatsetso li hlalositsoe tokomaneng ena molemong oa merero ea lefa feela, lithapo tsena ha li sa hlahisoa. Lithapo tse fumanehang hajoale bakeng sa odara ke lintho tse ncha tse lekanang ka botlalo.
Sehlomathiso A. Ho rarolla mathata ho Kenyelletsoa ha Mokhanni oa USB
Ho bohlokoa hore mosebelisi a kenye bakhanni pele o hokela PC ea mosebelisi ho thapo ea USB. Haeba thapo e hokahane pele e kenya bakhanni, Windows e tla leka ho kenya li-driver tsa eona tse kanna tsa se sebetse. Haeba mosebelisi a lekile ho hokela PC ho thapo ea USB ntle le ho qala ka ho kenya li-driver tse loketseng, kapa a na le bothata ba ho buisana le thapo ea USB ea Lattice ka mor'a ho kenya bakhanni, latela mehato e ka tlase:
- Hokela thapo ea USB ea Lattice. Khetha Qala > Litlhophiso > Panel ea taolo > Sisteme.
- Ka lebokoseng la puisano la Thepa ea Sistimi, tobetsa konopo ea Hardware le Selaoli sa Sesebelisoa. Tlas'a Universal Serial
Balaoli ba libese, mosebelisi o lokela ho bona Lattice USB ISP Programmer. Haeba mosebelisi a sa bone sena, batla Sesebelisoa se sa Tsejoeng se nang le folakha e mosehla. Penya habeli aekhoneng ea Sesebelisoa sa Unknown.
- Ka lebokoseng la puisano la Thepa e sa Tsejoeng, tobetsa Reinstall Driver.
- Khetha Batla komporo ea ka bakeng sa software ea mokhanni.
- Batla bukeng ea isptools\ispvmsystem bakeng sa mokhanni oa Lattice EzUSB
- Batla ho isptools\ispvmsystem\Drivers\FTDIUSBDriver directory bakeng sa mokhanni oa FTDI FTUSB.
- Bakeng sa lisebelisoa tsa Diamond, sheba ho lscc/diamond/data/vmdata/drivers. Tobetsa E latelang.
- Leha ho le joalo, khetha Kenya software ena ea Driver. Sistimi e nchafatsa mokhanni.
- Tobetsa Koala 'me u qete ho kenya mokhanni oa USB.
- Tlas'a Paneli ea Taolo> Sistimi> Motsamaisi oa Sesebelisoa> Balaoli ba Libese ba Universal Serial ba lokela ho kenyelletsa tse latelang:
a. Bakeng sa Mokhanni oa Lattice EzUSB: Sesebelisoa sa Lattice USB ISP Programmer se kentsoe.
b. Bakeng sa Mokhanni oa FTDI FTUSB: USB Serial Converter A le lisebelisoa tsa Converter B tse kentsoeng.
Haeba mosebelisi a na le mathata kapa a hloka tlhaiso-leseling e eketsehileng, ikopanye le Lattice Technical Support.
Sehlomathiso B. USB Programming Cable Firmware Update
Ho na le taba e tsebahalang moo thapo ea firmware e nang le mofuta oa V001 e ka etsang hore thapo ea lenaneo la USB e se ke ea sebetsa hantle ha lebone la LED le lula le lutse maemong a itseng. Tharollo ke ho nchafatsa firmware ea cable le mofuta oa firmware oa FTDI ho V002 ho rarolla bothata bona. Ka kopo, jarolla le ho kenya HW-USBN-2B Firmware version 2.0 kapa hamorao, e fumaneha ho rona websebaka. Firmware le tataiso ea litaelo tsa ntlafatso, e fumaneha ho rona websebaka
Thuso ea Tšehetso ea Theknoloji
Bakeng sa thuso, romella nyeoe ea tšehetso ea tekheniki ho www.latticesemi.com/techsupport.
Bakeng sa lipotso tse botsoang khafetsa, sheba ho Lattice Answer Database ho www.latticesemi.com/Support/AnswerDatabase.
Nalane ea Phetoho
Phetolelo ea 26.7, Mmesa 2024
| Karolo | Fetola Kakaretso |
| Programming Cable Pin Litlhaloso | Ntlha e ntlafalitsoeng ea 1 ho Lethathamo la 3.1. Programming Cable Pin Definitions ho bontša hore Nexus le Avant I2C programming ports ha li tšehetsoe. |
| Lenaneo la Flywire le Reference Connection | Lethathamo la 6.1. Reference Pin le Cable:
· Hlophisa mela ea sehlahisoa sa Nexus hore e be mola o le mong bakeng sa JTAG le likou tsa SSPI. · E kentse MachXO5-NX ho JTAG lethathamo la lisebelisoa tsa koung. · E tlositsoe lithapo tsa sehlahisoa sa Nexus bakeng sa boema-kepe ba I2C. |
Phetolelo ea 26.6 Pulungoana 2023
| Karolo | Fetola Kakaretso |
| Boithorollo | E ntlafalitsoe karolo ena. |
| Sehlomathiso A. Ho rarolla mathata ho Kenyelletsoa ha Mokhanni oa USB | Polelo e ekelitsoeng Ho na le taba e tsebahalang moo thapo ea firmware e nang le mofuta oa "V001" e ka etsang hore thapo ea lenaneo la USB e se ke ea sebetsa hantle le mabone a LED a lula a lutse maemong a itseng.
Tharollo ke ho nchafatsa firmware ea cable le mofuta oa firmware oa FTDI ho "V002" ho rarolla bothata bona. Ka kopo, khoasolla le ho kenya HW-USBN-2B Firmware mofuta 2.0 kapa hamorao, e fumanehang ho rona websebaka. |
| Sehlomathiso B. USB Programming Cable Firmware Update | E kentse karolo ena. |
Phetolelo ea la 26.5 Hlakubele 2023
| Karolo | Fetola Kakaretso |
| Lenaneo la Flywire le Reference Connection | E kentse Crosslink-NX, Certus-NX, CertusPro-NX le Mach-NX ho JTAG, lethathamo la lisebelisoa tsa SPI le tsa I2C Port ho Lethathamo la 6.1. Reference Pin le Cable. |
| Lisebelisoa tsa mananeo | Lintlha tse kenyellelitsoeng bakeng sa Port A le Port B “Port A ke ea JTAG mananeo. Radiant programming software e ka sebelisa thapo e hahelletsoeng ka har'a hub ea USB ho PC, e lemohang thapo ea ts'ebetso ea USB ho Port A. Ha Port B e le ea phihlello ea UART/I2C." |
| Tsohle | Referense ea Radiant e ekelitsoeng. |
| Tšehetso ea tekheniki | E kentse FAQ websehokelo sa sebaka. |
Phetolelo ea 26.4, Motšeanong 2020
| Karolo | Fetola Kakaretso |
| Lisebelisoa tsa mananeo | Lattice e ntlafalitsoeng websehokelo sa sebaka ho www.latticesemi.com/programmer |
| Lenaneo la Software |
Phetolelo ea 26.3, Mphalane 2019
| Karolo | Fetola Kakaretso |
| Maikutlo a Boto ea Maiketsetso;
Lenaneo la Flywire le Reference Connection |
Litekanyetso tse hlakisitsoeng tsa VCC tseo ke2C interface e tšehetsa. Lintlha tse kenyellelitsoeng ho Lethathamo la 6.1. |
Phetolelo ea 26.2, Motšeanong 2019
| Karolo | Fetola Kakaretso |
| — | Karolo e ekelitsoeng ea Boithopollo. |
| Lenaneo la Flywire le Reference Connection | Lethathamo la 6.1 le ntlafalitsoeng. Reference Pin le Cable.
· E kentse MachXO3D · E kentsoe CRESET_B ho Crosslink I2C. · Lintho tse ntlafalitsoeng tlas'a I2C Lisebelisoa tsa Boema-kepe · Ekelitsoe Platform Manager II. · Tsamaiso e fetotsoeng ea ispPAC. · Lintho tse ntlafalitsoeng tlas'a I2C Lisebelisoa tsa Boema-kepe. · Fetotse Power Manager II ho Platform Manager II le I2C e ntlafalitsoeng: boleng ba SDA. · Fetolela ASC ho L-ASC10 · E ntlafalitsoe mongolo o botlaaseng ba leqephe 4 ho kenyelletsa lisebelisoa tsa ispClock. · Matshwao a kgwebo a fetotsweng. |
| Nalane ea Phetoho | Sebopeho se ntlafalitsoeng. |
| Sekoahelo se ka morao | Template e ntlafalitsoeng. |
| — | Liphetoho tse nyane tsa bohlophisi |
Phetolelo ea 26.1, Motšeanong 2018
| Karolo | Fetola Kakaretso |
| Tsohle | Likenyo tse lokisitsoeng karolong ea Slave SPI Port Devices ea Lethathamo la 6.1. |
Phetolelo ea 26.0, Mmesa 2018
| Karolo | Fetola Kakaretso |
| Tsohle | · Nomoro ea tokomane e fetotsoeng ho tloha ho UG48 ho ea ho FPGA-UG-02024.
· Sebopeho sa tokomane se ntlafalitsoeng. |
| Lisebelisoa tsa mananeo | E tlositse tlhahisoleseling e sa hlokahaleng mme e fetotse sehokelo ho www/latticesemi.com/software. |
| Programming Cable Pin Litlhaloso | Mabitso a Ntlafatso ea Cable Pin ho Lethathamo la 3.1. Programming Cable Pin Litlhaloso. |
| Lenaneo la Flywire le Reference Connection | Fetiloe Tafole 2. Flywire Conversion Reference le Tafole 3 Likhokahano tsa Pin tse khothalelitsoeng ka Tafole e le 'ngoe ea 6.1 Pin le Reference Cable. |
| Ho Odara Boitsebiso | Lethathamo la 10.1. Programming Cable Feature Summary tlas'a Tlhahisoleseding ea ho Odara. |
Phetolelo ea 25.0 Pulungoana 2016
| Karolo | Fetola Kakaretso |
| Lenaneo la Flywire le Reference Connection | Lethathamo la 3 le ntlafalitsoeng, Lihokelo tsa Pin tse khothalelitsoeng. E kentse sesebelisoa sa CrossLink. |
Phetolelo ea 24.9, Mphalane 2015
| Karolo | Fetola Kakaretso |
| Lenaneo la Flywire le Reference Connection | Lethathamo la 3 le ntlafalitsoeng, Lihokelo tsa Pin tse khothalelitsoeng.
· E kentse kholomo ea CRESET-B. · E kenyellelitse sesebelisoa sa iCE40 UltraLite. |
| Thuso ea Tšehetso ea Theknoloji | Lintlha tse nchafalitsoeng tsa Thuso ea Tšehetso ea Theknoloji. |
Phetolelo ea la 24.8 Hlakubele 2015
| Karolo | Fetola Kakaretso |
| Programming Cable Pin Litlhaloso | Tlhaloso e ntlafalitsoeng ea INIT ho Lethathamo la 1, Litlhaloso tsa Pin ea Cable ea Programming. |
Phetolelo ea 24.7, Pherekhong 2015
| Karolo | Fetola Kakaretso |
| Programming Cable Pin Litlhaloso | · Ho Lethathamo la 1, Litlhaloso tsa Lenaneo la Cable Pin, ispEN/Enable/PROG e fetotsoe ho ispEN/Enable/PROG/SN le tlhaloso ea eona e ntlafalitsoe.
· Setšoantšo sa 2 se ntlafalitsoeng, Cable ea Programming In-System Programming Interface bakeng sa PC (HW-USBN-2B). |
| Lenaneo la Cable ispEN Pin | Ho Lethathamo la 4, Kakaretso ea Sebopeho sa Cable Cable, HW-USBN-2B e tšoailoe hore e teng bakeng sa odara. |
| Ho Odara Boitsebiso | HW-USBN-2A e fetotsoe ho HW- USBN-2B. |
Phetolelo ea 24.6, Phupu 2014
| Karolo | Fetola Kakaretso |
| Tsohle | E fetotsoe sehlooho sa tokomane ho tloha ho ispDOWNLOAD Lithapo ho ea ho Tataiso ea Basebelisi ba Lithapo tsa Lenaneo. |
| Programming Cable Pin Litlhaloso | Lethathamo la 3 le ntlafalitsoeng, likhokahano tsa Pin tse khothalelitsoeng. E kentse ECP5, iCE40LM, iCE40 Ultra, le malapa a lisebelisoa tsa MachXO3. |
| Litlhahiso tsa Moralo oa Boto e Lebeletsoeng | Karolo e ntlafalitsoeng. Sehokelo sa FAQ se ntlafalitsoeng mabapi le taolo ea sesebelisoa sa ispVM sa potoloho ea mosebetsi oa TCK le/kapa khafetsa. |
| Thuso ea Tšehetso ea Theknoloji | Lintlha tse nchafalitsoeng tsa Thuso ea Tšehetso ea Theknoloji. |
Phetolelo ea 24.5, Mphalane 2012
| Karolo | Fetola Kakaretso |
| Lenaneo la Flywire le Reference Connection | E kentse mabitso a li-port configuration iCE40 tafoleng ea Flywire Conversion Reference. |
| Lenaneo la Flywire le Reference Connection | E kentse lintlha tsa iCE40 tafoleng ea Khokahano ea Cable e Recommendedng. |
Phetolelo ea 24.4, Hlakola 2012
| Karolo | Fetola Kakaretso |
| Tsohle | Tokomane e ntlafalitsoeng e nang le logo e ncha ea khoebo. |
Phetolelo ea 24.3 Pulungoana 2011
| Karolo | Fetola Kakaretso |
| Tsohle | Tokomane e fetiselitsoe ho sebopeho sa tataiso ea mosebelisi. |
| Likaroloana | Setšoantšo se ekelitsoeng Cable ea USB - HW-USBN-2A. |
| Lenaneo la Flywire le Reference Connection | Tafole e ntlafalitsoeng ea Khokahano ea Cable e khothalelitsoeng bakeng sa lisebelisoa tsa MachXO2. |
| Litlhahiso tsa Moralo oa Boto e Lebeletsoeng | Karolo e ntlafalitsoeng. |
| Sehlomathiso A | Karolo e ekelitsoeng. |
Phetolelo ea 24.2, Mphalane 2009
| Karolo | Fetola Kakaretso |
| Tsohle | Lintlha tse ling tse amanang le lintlha tsa 'mele tsa likhokahano tsa flywire. |
Phetolelo ea 24.1, Phupu 2009
| Karolo | Fetola Kakaretso |
| Tsohle | Karolo ea mongolo e Ekelitsoeng ea Litlhaloso tsa Boto ea Maikutlo. |
| Lenaneo la Flywire le Reference Connection | E kentse sehlooho sa karolo. |
Liphetoho tse Fetileng
| Karolo | Fetola Kakaretso |
| — | Litokollo tse fetileng tsa Lattice. |
2024 Lattice Semiconductor Corp. Matshwao a kgwebo kaofela a Lattice, matshwao a kgwebo a ngodisitsweng, dipatente, le boithorollo ke tse thathamisitsweng ho. www.latticesemi.com/legal. Mabitso a mang kaofela a mofuta kapa lihlahisoa ke matšoao a khoebo kapa matšoao a ngolisitsoeng a beng ba ona ka ho fapana. Litlhaloso le tlhahisoleseling mona li ka fetoha ntle le tsebiso
E jarollotsoe ho tsoa Arrow.com
Litokomane / Lisebelisoa
 |
LATTICE HW-USBN-2B Programming Cables [pdf] Bukana ea Mosebelisi HW-USBN-2B Programming Cables, HW-USBN-2B, Programming Cables, Cables |
