HO PHELELA KA SEJANA
Boitsebiso ba Theknoloji
Li-sensor
Ultrasonic Controller / Sensor
Nalane ea ntlafatso
Lethathamo la litlhahlobo
| Letsatsi | Fetohile |
Moruti |
| La 2015 Pulungoana XNUMX | Boholo ba mocheso oa ho sebetsa | 0401 |
| Loetse 2015 | E fetoletsoe ho sebopeho sa Danfoss | CA |
| Mphalane 2012 | Ho tlositsoe molaoli 1035027 le 1035039 | BA |
| Hlakubele 2011 | E kenyellelitsoe PLUS+1® e lumellanang | AB |
| Hlakola 2011 | E nkela sebaka BLN-95-9078 | AA |
Fetileview
Tlhaloso
Ultrasonic Controller/Sensor e ntlafalitsoe ho nka sebaka sa li-paddle kapa wand sensors. Ka bobeli ha li kopane 'me ka hona ha li na bothata ba boemo kapa motsamao o amanang le li-sensor tse tloaelehileng tsa mochini. Lihlahisoa tsena hangata li sebelisetsoa ho utloa le ho laola ho phalla ha lintho. Liyuniti tsohle li lekanya sebaka sa sebaka seo ho shebiloeng ho sona ebe li hlahisa sephetho. 1035019, 1035026, 1035029, le balaoli ba 1035036 Balaoli bana ba hlahisa lets'oao, le fapaneng ka ho lekana le sebaka, ho laola Motlakase oa Phallo ea Motlakase (EDC) bakeng sa phetiso ea hydrostatic. Motsoako o tsoang ho molaoli ke "pulse-width modulated, high-side switched valve drive", e nang le sehlopha se moqotetsane se lekanang. Bakeng sa ts'ebetso e bonolo le ho hlongoa, sebaka sa ho lemoha sa Ultrasonic Controller/Sensor se ka fetoloa ka ho fetola konopo e ka ntle e behiloeng holim'a screed kapa ka ho kenya li-switches tsa dome holim'a sekoaelo sa lisebelisoa. 1035024 molaoli
Molaoli enoa o khanna valve ea litsela tse tharo e laoloang ke solenoid e nang le tlhahiso e ka bang (matla a feletseng) ha sensor e le hōle le sepheo kapa e tima (matla a zero) ha sepheo se le haufi. Bophahamo ba eona bo ka fetoloa ka knob ho screed kapa ka ho kenya li-switches tsa dome holim'a sekoaelo sa lisebelisoa. 1035025 e ts'oana le 5024, ntle le hore tlhahiso e fetotsoe. 1035022, 1035028, 1035040, le li-sensor tsa 1035035
Li-sensor tsena li hlahisa molumo oa analogetage output to drive an amplifier bakeng sa ho laola li-EDC kapa li-valve tsa mahlakore a mabeli. Sephetho se fapana ka ho lekana ho pholletsa le mefuta eohle ea ts'ebetso. 1035023 sensor
Sensor ena e hlahisa tlhahiso ea PWM e lekanang le sebaka ho tloha ho sensor ho ea ho sepheo. Ea kantle amplifier e laola letšoao bakeng sa ho laola EDCs kapa li-valve tsa bi-directional.
Sheba Lintlha tsa Tekheniki leqepheng la 6, Litlhaloso tsa Pin ea Sehokelo leqepheng la 6, le Litlhophiso leqepheng la 7.
Likaroloana
- Sensor e sa kopaneng
- Ho bonolo ho kenya
- Sebaka se pharaletseng sa ts'ebetso
- Litholoana tsa ho khanna ampli-lifiers kapa li-valve ka kotloloho
- Sebaka se feto-fetohang
- On/Off kapa proportional controller; kapa li-sensor tsa ratiometric
Khopolo ea ts'ebetso
Karolo ea sensor ea Ultrasonic Controller / Sensor e hlahisa leqhubu la ultrasonic mme e amohela lets'oao le bonts'itsoeng morao ho tloha sebakeng se lebisitsoeng. Phapang ea nako lipakeng tsa tlhahiso le kamohelo e lekanngoa le sebaka. Lihlahisoa tsa sensor li ntša lets'oao lena la hole joalo ka voltage ho a amplifier, moo e sebelisetsoang ho laola valve e fetolang lebelo la phallo ea phetiso ea hydrostatic kapa boemo ba cylinder. Sheba potoloho e bulehileng ea 1035022, 1035028 potoloho e koetsoeng, 1035035, 1035040 leqepheng la 13. Karolo ea taolo ea Ultrasonic Controller / Sensor e sebelisa hlooho e tšoanang ea kutlo joaloka li-sensor, empa e fana ka tlhahiso ea bobeli ea taolo. Sheba 1035019, 1035026, 1035029, 1035030, 1035036 leqepheng la 12.
Sephetho sa bobeli ke pulse-width modulated (PWM). Bakeng sa mohlalaample., leqhubu la lisekoere le fapaneng ho tloha ho input voltage (holimo) ho ea ho li-volts tsa lefela (tlase) tseo karolo ea tsonatagNako e phahameng ka potoloho e fapana ho ea ka sebaka se lekantsoeng. Sephetho sa PWM se lokiselitsoe ho khanna valve ka kotloloho. Hang ha molaoli a kentsoe, sebaka se lakatsehang ho tloha moo ho shebiloeng se ka fapana ka sesebelisoa sa dome se holim'a sefahleho sa sesebelisoa kapa ka potentiometer e fumanehang hole.
Phallo ea 1035024 e ka ba (matla a feletseng) kapa a tima (matla a zero) bakeng sa ho sebelisoa ka li-valve tsa solenoid, bona 1035024, 1035025 leqepheng la 12. Ha sensor e le 29 cm kapa e kholo ho tloha ho sepheo, ha e behiloe ho fetola bonyane ba bophahamo, matla a teng. e tletse ho fihlela sepheo se le 25 cm kapa ka tlase ho moo, ka nako eo matla a tima. Joalo ka li-control tse ling tsa ultrasonic, bophahamo bo lakatsehang bo ka fetoloa ka li-switches tsa dome kapa pitsa e hole. Ha lihlahisoa tse tsoang ho sensor / controller li fapane, koloi ea hydrostatic e fapana le tekanyo ea phallo ea thepa, e leng se etsang hore ho behoe sebaka sa sepheo. Sheba setšoantšo sa Taolo leqepheng la 14. Ha boemo ba sepheo bo ntse bo fapana ho ea ka li-curve tse bontšitsoeng, tsamaiso e tla tsoela pele ho batla ntlha ea tekano. The 1035026 le 1035022 li na le liphetho tse lekanang tseo hangata li hlahisang tlhahiso e tsoelang pele, e leng se bakang taolo e ts'oanang ea lebelo la mochini oa phallo ea thepa. 1035024 e ka hlahisa ho emisa ha nakoana le ho qala ha phallo ea thepa.
Lisebelisoa tse tloaelehileng tsa Ultrasonic Controller / Sensor li kenyelletsa: ho laola lebelo la auger / conveyor drive holim'a li-asphalt pavers, taolo ea boemo ba liheke tse otlang ka lijo bakeng sa li-pavers tsa asphalt kapa tsa konkreite, taolo ea boemo ba mekhoa ea li-contour le tekanyo ea hole le ho hlahloba.
Sehlahisoa se amanang
Lisebelisoa
| KE14010 Taolo ea ho fepa Ampmoqhobi | Boto ea potoloho e hatisitsoeng, KE14010 e amohela lets'oao le tsoang ho 1035022 kapa MCX102A Potentiometer Sensor le ho kenya Taolo ea Phallo ea Motlakase (EDC) pompong ea hydrostatic. |
| KW01028 Cable | E hokela 1031097, 1035026 kapa 1035024 ho hlooho ea mochini. Lihokelo tsa MS lipheletsong ka bobeli. Li-socket tse tšeletseng pheletsong ea sensor, li-socket tse hlano pheletsong ea mochini. Li-conductor tse tharo. Khoele ea maoto a mabeli e fihla ho limithara tse leshome. |
| KW01009 Cable | E hokela 1035026 kapa 1035024 ho hlooho ea mochini. Lihokelo tsa MS lipheletsong ka bobeli. Li-socket tse tšeletseng mahlakoreng ka bobeli. Bakhanni ba bane. Khoele ea maoto a mabeli e fihla ho limithara tse leshome. |
| KW01029 Cable | E hokela 1035022 ho MCP112A1011. Lihokelo tsa MS lipheletsong ka bobeli. Socket e tšeletseng pheletsong ea sensor, socket e mehlano pheletsong ea taolo. Li-conductor tse tharo. Khoele ea maoto a mabeli e fihla ho limithara tse leshome. Plug e lumellana le MCX102A1004. |
| 1031109 Cable | E hokela 1035026 kapa 1035024 ho hlooho ea mochini. Lihokelo tsa MS lipheletsong ka bobeli. Li-socket tse tšeletseng mahlakoreng ka bobeli. Bakhanni ba bane. Khoele e le 'ngoe le halofo ea leoto la khoele e otlolla ho fihla ho limithara tse supileng le halofo. |
| 1035060 Pitsa e hole | E kenya potentiometer tsamaisong. |
Lintlha tsa tekheniki
Litlhaloso
| Mocheso o tsoelang pele oa ho sebetsa | 14 ho isa ho 185° F (-10 ho isa ho 85° C) |
| Phepelo voltage | 10 ho isa ho 30 Vdc |
| Sebaka sa ts'ebetso | 16 ho 100 cm (6.3 ho 39.4 in) e fapana ho ea ka mohlala. |
| Proportional valve drive e hlahisoang (1035026) | 0–240 mA (12 Vdc moroalo oa 20 ohm) 0–240 mA (24 Vdc ho mojaro oa 80 ohm) e fetotsoe ka lehlakoreng le phahameng |
| Maqhubu a koloi ea li-valve (1035026) | 1000 Hz, bophara ba sekhahla se fetotsoe |
| Tlhahiso ea koloi ea ON/OFF (1035024) | 2.0 amp palo e kahodimodimo ho 7 ohm bonyane ba mojaro Lehlakoreng le phahameng le fetotswe |
| Sehlopha sa taolo (1035024) | 4 cm (1.6 in) |
| Sephetho sa Analog (1035022) | 1.5 Vdc ho 6.3 inches (16 cm) 8.5 Vdc ho 39.4 inches (100 cm) |
| Ho sitisa sephetho bakeng sa tlhahiso ea analoge | 1000 ohms, bonyane |
Litlhaloso tsa phini ea sehokelo
| Nomoro ea karolo | A | B | C | D | E |
F |
| 1035019 | BATT (+) | PITŠA (-) | BATT (-) | Tlhahiso ea PWM | Maikutlo a POT | POT (+) |
| 1035022 | BATT (+) | Tlhahiso ea DC | BATT (-) | Ha e sebelisoe | Ha e sebelisoe | Ha e sebelisoe |
| 1035023 | BATT (+) | BATT (-) | Tlhahiso ea PWM | BATT (-) | Ha e sebelisoe | Ha e sebelisoe |
| 1035024 | BATT (+) | POT (+) | BATT (-) | ON/OFF tlhahiso | PITŠA (-) | Maikutlo a POT |
| 1035025 | BATT (+) | POT (+) | BATT (-) | ON/OFF tlhahiso | Maikutlo a POT | N/A |
| 1035026 | BATT (+) | POT (+) | BATT (-) | Tlhahiso ea PWM | PITŠA (-) | Maikutlo a POT |
| 1035028 | BATT (+) | Tlhahiso ea DC | BATT (-) | Ha e sebelisoe | Ha e sebelisoe | Ha e sebelisoe |
| 1035029 | BATT (+) | POT (+) | BATT (-) | Tlhahiso ea PWM | PITŠA(-) | Maikutlo a POT |
| 1035030 | BATT (+) | POT (+) | BATT (-) | Tlhahiso ea PWM | PITŠA (-) | Maikutlo a POT |
| 1035035 | BATT (+) | BATT (-) | Tlhahiso ea DC | Ha e sebelisoe | Ha e sebelisoe | N/A |
| 1035036 | BATT (+) | PITŠA (-) | BATT (-) | Tlhahiso ea PWM | Maikutlo a POT | POT (+) |
| 1035040 | BATT (+) | Tlhahiso ea DC | BATT (-) | Ha e sebelisoe | Ha e sebelisoe | Ha e sebelisoe |
Litlhophiso
Litlhophiso
| Nomoro ea karolo | Phopholetsa mefuta e fapaneng | Sebaka sa taolo | Mofuta oa taolo | Nako ea tlhahiso | Boiphetetso ba sephetho | Ho lahleheloa ke lets'oao tlhahiso | Pitsa e hole |
| 1035019 | 25 ho isa ho 100 cm (9.8 ho isa ho 39.4 in) |
30 cm (11.8 in) | Proportional PWM High-lehlakoreng switjha | 200 Hz | 180 ohm | Augers ON | Ee |
| 1035022 | 16 ho isa ho 100 cm (6.3 ho isa ho 39.4 in) |
N/A | Litekanyo 1.5 ho isa ho 8.5 Vdc |
DC | 1000 ohm | Sends far target voltage (Augers ON) | Che |
| 1035023 | 20 ho isa ho 91 cm (8.0 ho isa ho 36.0 in) |
N/A | Litekanyo Ho fetoha ha maemo a tlase |
5000 Hz | 250 ohm | Augers ON | Che |
| 1035024 | 29 ho isa ho 100 cm (11.5 ho isa ho 39.5 in) |
4 cm (1.6 in) | ON/OFF Ho switjha ka lehlakoreng le phahameng | BONAHALA/TSHA | 0 ohm | Augers ON | Ee |
| 1035025 | 29 ho isa ho 100 cm (11.5 ho isa ho 39.5 in) |
4 cm (1.6 in) | ON/OFF Ho feto-fetoha ha maemo a holimo (ho inverted) | BONAHALA/TSHA | 0 ohm | Augers ON | Che |
| 1035026 | 29 ho isa ho 100 cm (11.5 ho isa ho 39.5 in) |
20 cm (8.0 in) | Proportional PWM High-lehlakoreng switjha | 1000 Hz | 25 ohm (0 ho isa ho 240 mA ho 20 Ohms @ 12 Vdc, 80 Ohms @ 24 Vdc) |
Augers ON | Ee |
| 1035028 | 16 ho isa ho 100 cm (6.3 ho isa ho 39.4 in) |
N/A | Litekanyo 0.5 ho isa ho 4.5 Vdc |
DC | 1000 ohm | Sends close target voltage (Augers OFF) | Che |
| 1035029 | 29 ho isa ho 100 cm (11.5 ho isa ho 39.5 in) |
30 cm (11.8 in) | Proportional PWM High-lehlakoreng switjha | 1000 Hz | 0 ohm | Augers ON | Ee |
| 1035030 | 29 ho isa ho 100 cm (11.5 ho isa ho 39.5 in) |
20 cm (8.0 in) | Proportional PWM High-lehlakoreng switjha | 1000 Hz | 0 ohm | Augers ON | Ee |
| 1035035 | 16 ho isa ho 100 cm (6.3 ho isa ho 39.4 in) |
N/A | Litekanyo 1.5 ho isa ho 8.5 Vdc |
DC | 1000 ohm | Sends far target voltage (Augers ON) | Che |
| 1035036 | 20 ho isa ho 100 cm (7.9 ho isa ho 39.4 in) |
25 cm (9.8 in) | Proportional PWM High-lehlakoreng switjha | 1000 Hz 12% Min. Mosebetsi Cycle (98% Max) | 0 ohm | Augers ON | Ee |
| 1035040 | 16 ho isa ho 100 cm (6.3 ho isa ho 39.4 in) |
N/A | Litekanyo 0.5 ho isa ho 4.5 Vdc |
DC | 1000 ohm | Sends far target voltage (Augers ON) | Che |
Litekanyo
mm [li-inch]
Tshebetso
Setulo sa ts'ebetso
- Ho hatella li-switches tse peli tsa dome ka nako e le 'ngoe ho tla beha boemo bo phahameng ba thepa ho bophahamo ba hona joale (ho theha sebaka se behiloeng).
- E 'ngoe le e' ngoe ea ho sutumetsa ea dome e tla fetola bolelele ba thepa e ka bang 0.5 cm (0.2 in).
- Ho tobetsa konopo ea ho eketsa kapa ho fokotsa ho tla tsamaisa sehlopha sa taolo se tsitsitseng sebakeng sa mosebetsi.
- Phallo ea PWM e mela ho tloha ho 0% ho isa ho 100% ho feta sehlopha sa taolo.
- Haeba sepheo se lahlehile kapa se le sieo, sesebelisoa se tla tsamaisetsa li-LED tse tharo holimo le tlase ho graph ea LED.
- Bakeng sa balaoli, graph ea LED e bonts'a sebaka se behiloeng.
- Bakeng sa li-sensor, bar-graph ea LED e bonts'a bophahamo ba thepa.
- Haeba potentiometer e hokahane, e nka pele ho li-switches tsa push-button mme li-switches tsa push-button lia tima. Leha ho le joalo, li-switches tsa push-button li ntse li ka sebelisoa ho kenya tlhahlobo ea matsoho.
- Setha-point ea morao-rao e bolokiloe mohopolong 'me e tla bolokoa haeba motlakase o lahlehile, ebe e khutlisoa ha motlakase o buletsoe hape.
Teko ea tšebetso ea matsoho (bakeng sa balaoli feela)
Ultrasonic Controller/Sensor e na le software ea moahi ho etsa tlhahlobo ea matsoho nako efe kapa efe eo ts'ebetso ea sesebelisoa e belaelloang.
Ho kenya mokhoa oa tlhahlobo ea matsoho
- Ho kenya mokhoa oa teko, ka nako e le 'ngoe tobetsa likonopo tse peli tsa membrane (konopo ea ho eketsa le konopo ea ho fokotsa).
- Tsoela pele ho tšoara konopo ea ho fokotsa (-), 'me u lokolle konopo ea ho eketsa (+).
- Ka mor'a moo, tobetsa konopo ea eketsa (+) makhetlo a leshome a eketsehileng, ha u ntse u tsoela pele ho tšoara konopo ea ho fokotsa (-). Ha o qetile ka katleho tatellano ena, transducer e tla emisa ho fetisetsa ho phatloha ha ultrasonic, 'me li-LED tse 10, ka har'a graph ea LED, li tla qala mokhoa oa ho sisinyeha o tla qala ho tloha lipheletsong tsa graph ea bar ho ea bohareng ba bar. kerafo. Ena ke pontšo ea hore u atlehile ho kenya mokhoa oa tlhahlobo ea matsoho.
Ha u ntse u kena tekong, u atlehile ho sebelisa li-switches tsa membrane. Mokhoa oa ho kenya mokhoa oa teko, hammoho le ho tobetsa likonopo ho tsamaea ka har'a tlhahlobo ea tataiso, e sebetsa e le teko ea ho fetola membrane.
Ho tsamaisa liteko tse hlano tsa matsoho
Tlhahlobo ea matsoho stagng
- Lokolla li-switches tse peli tsa push-button.
Hona joale u mothating oa pele oa tlhahlobo ea matsoho. Sena ke joalo kataging mohato o ka bonoang ka tatellano ea ponts'o e benyang ea LED. - Ka boikhethelo: Ho etsa tlhahlobo e latelang, tobetsa konopo ea theola hang.
- Ka boikhethelo: Ho etsa tlhahlobo e fetileng, tobetsa konopo ea eketsa hang.
E-ea tekong ea pele, tekong ea ho qetela, 'me u khutle hape ka ho tobetsa ka nako e le 'ngoe konopo ea ho eketsa le konopo ea ho fokotsa.
Teko ea memori ea EEPROM
Tobetsa 'me u lokolle konopo ea ho fokotsa hang ho etsa tlhahlobo ena. Micro-controller e tla tsamaisa tlhahlobo ea EEPROM ka bo eona.
Ho phethoa ka katleho ha tlhahlobo ho tla etsa hore li-LED tsohle li be teng. Haeba tlhahlobo ena e hlōleha, joale li-LED tsohle li tla khanya.
Haeba li-LED li khanya, sebaka se le seng kapa ho feta sa EEPROM ha se khone ho hlophisoa bocha.
Teko ea LED e tla sebetsa hape ka ho tobetsa le ho lokolla konopo ea keketseho.
Teko ea LED
- Tobetsa 'me u lokolle konopo ea ho fokotsa hang ho qala tlhahlobo e latelang.
Ha u kena tekong ena, LED ka 'ngoe e tla bulela, ebe e tima hape, ka tatellano. - Opereishene e tlameha ho netefatsa hore motho ka mong oa LED ka har'a bar-graph e ea sebetsa. Ha ho na nako eo li-LED tse peli li lokelang ho khantšoa ka nako e le 'ngoe.
Teko ea memori ea EEPROM e tla sebetsa hape ka ho tobetsa le ho lokolla konopo ea keketseho.
Teko ea potentiometer / LED
Tobetsa 'me u lokolle konopo ea ho fokotsa hang ho qala tlhahlobo ena.
Haeba sesebelisoa se khona ho ba le potentiometer, joale ho fetola pitsa ho tla fetola mabone a pontšo. Ho itšetlehile ka hore na pitsa e hokahane joang, ho e fetola ka ho feletseng ka tsela e le 'ngoe ho tla etsa hore li-LED tsohle li bulehe. Ho e fetola hohle ka lehlakoreng le leng ho tla etsa hore li-LED tsohle li time, ntle le LED 0 (LED e nyenyane ka ho fetisisa ho graph ea LED bar). LED 0 e tla lula e le teng nakong ea teko ena.
Ha graph ea LED e ntse e eketseha ka bolelele, tlhahiso e tsoang ho PWM e tla eketseha, hape.
Haeba ho se na potentiometer e hoketsoeng, tlhahiso e itseng e sa reroang e tla hlaha hammoho le ponts'o e itseng ea LED.
Tlhokomeliso
Haeba li-augers tsa paver li setiloe ka mokhoa oa othomathike, ho etsa tlhahlobo ena ho tla fetola li-augers.
Teko ea Potentiometer / LED e tla boela e sebetse ka ho tobetsa le ho lokolla konopo ea ho eketsa.
Ultrasonic transceiver/LED/output driver driver
Tobetsa 'me u lokolle konopo ea ho fokotsa hang ho kenya teko ena.
Transducer ea ultrasonic joale e tla kenya tšebetsong ebe e qala ho fetisa matšoao le ho amohela li-echoes.
Transducer e tlameha ho supetsoa moo ho lokiselitsoeng ho phethela tlhahlobo ena. Hape, ho tlameha ho be le mokhoa o nepahetseng oa ho lekanya tlhahiso ea PWM ho tsoa ho mokhanni oa valve.
Ha sesebelisoa se ntse se lebisitsoe ho sepheo, tlhahiso ea PWM e tla ea ho potoloho ea eona e fokolang ea mosebetsi kapa potoloho ea eona e phahameng ea mosebetsi, ho itšetlehile ka tlhophiso ea sesebelisoa.
Ha sesebelisoa se tlositsoe hole le sepheo, tlhahiso ea PWM e tla ea potolohong ea eona e phahameng ea mosebetsi kapa potoloho ea eona e tlase ea mosebetsi, ho ipapisitse le tlhophiso ea sesebelisoa. Ha sesebelisoa se suthela hole le sepheo, ponts'o ea LED e tla tloha ho li-LED tsohle ho ea ho li-LED tsohle tse tingoeng, ntle le ho bonyane ba bohlokoa ba LED ka har'a sehlopha. LED 0 e lula e le teng nakong ea teko ena.
Tlhokomeliso
Haeba li-augers tsa paver li setiloe ka mokhoa oa othomathike, ho etsa tlhahlobo ena ho tla fetola li-augers.
Ultrasonic transceiver/LED/output driver test e tla sebetsa hape ka ho tobetsa le ho lokolla konopo ea keketseho.
E tsoa molemong oa tlhahlobo ea matsoho
Ho tobetsa le ho lokolla konopo ea ho fokotsa nako e le 'ngoe ho tla lumella Ultrasonic Controller/Sensor ho kenya tlhahlobo ena.
U tla khona ho lemoha tlhahlobo ena ka ho sheba transducer le graph ea LED. Transducer e tla emisa ho fetisa 'me li-LED tsa 10, ho graph ea LED ea bar, li tla qala mokhoa oa ho sisinyeha o tla qala ho tloha lipheletsong tsa graph ea bar ho ea bohareng ba graph ea bar.
Ho tsoa boemong ba tlhahlobo ea matsoho ho tla sebetsa hape ka ho tobetsa le ho lokolla konopo ea ho eketsa.
Mokhoa oa ho etsa liteko o tsoile 'me ts'ebetso e tloaelehileng e qala hape ka ho tobetsa konopo ea keketseho le konopo ea ho fokotsa ka nako e ts'oanang.
Setšoantšo sa tsamaiso
Setšoantšo sa tsamaiso
Setšoantšo sa taolo
Setšoantšo sa taolo
1035022, 1035028, 1035035, 1035040
Laola mefuta e mengata ea tlhahiso ea analog (pin B) bakeng sa 103522, 1035028 Ultrasonic Control / Sensor. Phepelo voltage ke 12 kapa 24 Vdc le li-impedances tsa tlhahiso 1 k ohm.
Lihlahisoa tseo re fanang ka tsona:
- Bent Axis Motors
- Lipompo tsa Circuit Axial Piston tse Koetsoeng le Motors
- Lipontšo
- Motlakase oa Motlakase oa Motlakase
- Elektrohydraulics
- Tsamaiso ea Matla a Hydraulic
- Mekhoa e Kopanetsoeng
- Li-Joystick le Li-Handles tsa Taolo
- Li-Microcontroller le Software
- Bula Lipompo tsa Piston tsa Circuit Axial
- Likoloi tsa Orbital
- PLUS+1 ® TATAISO
- Li-valve tse lekanang
- Li-sensor
- Ho tsamaisa
- Transit Mixer Drives
Litharollo tsa Matla a Danfoss ke moetsi oa lefats'e le mofani oa thepa ea boleng bo holimo ea haeteroliki le lisebelisoa tsa elektroniki. Re ipapisitse le ho fana ka theknoloji ea morao-rao le litharollo tse ipabolang maemong a thata a ts'ebetso ea 'maraka oa mehala o kantle ho litsela tse kholo. Ho ipapisitse le boiphihlelo ba rona ba lits'ebetso tse pharalletseng, re sebetsa haufi-ufi le bareki ba rona ho netefatsa ts'ebetso e ikhethang bakeng sa mefuta e mengata ea makoloi a sa tsamaeeng.
Re thusa li-OEM lefatšeng ka bophara ho potlakisa nts'etsopele ea sistimi, ho fokotsa litšenyehelo le ho tlisa likoloi 'marakeng kapele.
Danfoss - Molekane oa Hao ea Matla ka ho Fetisisa ho Mobile Hydraulics.
Eya ho www.powersolutions.danfoss.com bakeng sa lintlha tse ling tsa sehlahisoa.
Kae kapa kae moo likoloi tse tsoang tseleng li sebetsang teng, ho joalo le ka Danfoss. Re fana ka tšehetso ea litsebi lefatšeng ka bophara bakeng sa bareki ba rona, ho netefatsa litharollo tse ntle ka ho fetisisa bakeng sa ts'ebetso e ikhethang. 'Me ka marang-rang a pharaletseng a Global Service Partners, re boetse re fana ka litšebeletso tse pharaletseng tsa lefats'e bakeng sa likarolo tsohle tsa rona.
Ka kopo ikopanye le moemeli oa Danfoss Power Solution e haufi le uena.
Comatrol
www.comatrol.com
Schwarzmüller-Inverter
www.schwarzmuellerinverter.com
Turolla
www.turollaocg.com
Hydro-Gear
www.hydro-gear.com
Daikin-Sauer-Danfoss
www.daikin-sauer-danfoss.com
Aterese ea sebaka seo:
Lerato
Khampani ea Tharollo ea Matla (US).
2800 East 13th Street
Ames, IA 50010, USA
Mohala: +1 515 239 6000
Lerato
Power Solutions GmbH & Co. OHG
Krokamp 35
D-24539 Neumünster, Jeremane
Mohala: +49 4321 871 0
Lerato
Power Solutions GmbH & Co. OHG
Krokamp 35
D-24539 Neumünster, Jeremane
Mohala: +49 4321 871 0
Lerato
Power Solutions Trading (Shanghai) Co., Ltd.
Mohaho #22, No. 1000 Jin Hai Rd
Jin Qiao, Setereke se Secha sa Pudong
Shanghai, Chaena 201206
Mohala: +86 21 3418 5200
Danfoss e ke ke ea amohela boikarabello bakeng sa liphoso tse ka bang teng libukeng tsa libuka, libukana le lintho tse ling tse hatisitsoeng. Danfoss e na le tokelo ea ho fetola lihlahisoa tsa eona ntle le tsebiso. Sena se sebetsa le ho lihlahisoa tse seng li ntse li laetsoe hafeela liphetoho tse joalo li ka etsoa ntle le liphetoho tse hlokahalang ho latela litlhaloso tse seng li lumellane. Matšoao ohle a khoebo a thepa ena ke thepa ea lik'hamphani tse amehang. Danfoss le mofuta oa logo ea Danfoss ke matšoao a khoebo a Danfoss A/S. Litokelo tsohle li sirelelitsoe.
L1009343 Rev 0401 November 2015
www.anopela.com
© Danfoss A/S, 2015
Litokomane / Lisebelisoa
 |
Danfoss Sonic Feeder Ultrasonic Controller, Sensor [pdf] Buka ea Taelo 1035019, 1035026, 1035029, 1035036, 1035024, 1035022, 1035028, 1035040, 1035035, 1035023, Sonic Feedler Sensoerronic, Sonic Feeder Sensoer nsor, Ultrasonic Controller, Ultrasonic Sensor |