Altronix AL1024NKA8 Letoto la Litaolo tsa Matla a Mabeli a Liphello tse Hlahang

Fetileview

Altronix AL1024NKA8 le AL1024NKA8D li aba le ho fetola matla ho fihlella lisebelisoa tsa taolo le lisebelisoa. Ba fetola tlhahiso ea 115VAC 60Hz ho tse robeli (8) tse laoloang ka boithaopo tsa 12VDC kapa 24VDC tse sirelelitsoeng. Moralo oa ho kenya habeli oa Access Power Controller o lumella matla ho tsamaisoa ho tloha ho tse peli (2) tse kentsoeng fekthering tse tlase tse ikemetseng.tage 12 kapa 24VDC Altronix lisebelisoa tsa matla ho tse robeli (8) tse laoloang ka mokhoa o ikemetseng (AL1024NKA8) kapa PTC (AL1024NKA8D) tse sirelelitsoeng. Lisebelisoa tsa motlakase li ka fetoloa hore e be mabitso a "C" a omileng. Lintho tse hlahisoang li sebelisoa ke sink e bulehileng ea pokello, e atisang ho buloa (NO), hangata e koetsoeng (NC) ho kenya mochine o omileng, kapa metsi a tsoang ho Access Control System, Card Reader, Keypad, Push Button, PIR, joalo-joalo AL1024NKA8(D) e tla matla a tsela ho ea ho lisebelisoa tse fapaneng tsa ho laola lisebelisoa tsa lisebelisoa tse kenyeletsang Mag Locks, Litlhaselo tsa Motlakase, Magnetic Door Holders, joalo-joalo Liphetho li tla sebetsa ka mekhoa e 'meli ea Fail-Safe le / kapa Fail-Secure. FACP Interface e nolofalletsa Emergency Egress, Alarm Monitoring, kapa e ka sebelisoa ho kenya lisebelisoa tse ling tse thusang. Karolo ea ho khaola alamo ea mollo e ka khethoa ka bonngoe bakeng sa liphetho tse robeli kapa tse robeli (8). Lihokelo tsa li-spade li u lumella ho kenya matla a mahlahahlaha ho li-module tse ngata tsa ACMS8(CB). Karolo ena e u lumella ho aba matla holim'a liphetho tse ngata bakeng sa litsamaiso tse kholoanyane.

Litlhaloso tsa Boemo (kakaretso e bonts'itsoeng)

Sephetho	15 mets. ea Stand-by le 5 mets. ea Alamo	4 hora. ea Stand-by le 5 mets. ea Alamo	Lihora tse 24. ea Stand-by le 5 mets. ea Alamo	Lihora tse 60. ea Stand-by le 5 mets. ea Alamo
24VDC/12AH Betri	Ema-Haufi = 8A Alamo = 10A	Ema-Haufi = 1.5A Alamo = 10A	Stand-By = 200mA Alamo = 10A	Stand-By = 100mA Alamo = 10A
Sephetho	15 mets. ea Stand-by le 5 mets. ea Alamo	4 hora. ea Stand-by le 5 mets. ea Alamo	24 hora. ea Stand-by le 15 mets. ea Alamo	60 hora. ea Stand-by le 15 mets. ea Alamo
24VDC/65AH Betri	–	Ema-Haufi = 8.0A Alamo = 10A	Ema-Haufi = 1.5A Alamo = 10A	Stand-By = 500mA Alamo = 10A

Bakeng sa lits'ebetso tsa Taolo ea Phihlello, matla a betri bakeng sa phepelo ea 10A hajoale - 1 hr. bakeng sa betri ea 24VDC/12AH, lihora tse 6.5. bakeng sa betri ea 24VDC/65AH. Sheba leqephe la ho bala boholo ba betri ka tlase bakeng sa libeteri tse ling.

• A. AL1024NKA8(D) tshebediso ya ka hare ya jwale (e emeng ka tsela) ________________ 0.05 A
• B. Laola tšebeliso ea hona joale (e eme ka tsela) ________________ A
• C. Nako ea ho ema e hlokahalang (lihora) ________________ H
• D. Bokhoni ba betri bo hlokahalang bakeng sa ho ema (A+B)*C ________________ AH
• E. AL1024NKA8(D) tšebeliso ea matla ka hare (Alamo) ________________ 0.05 A
• F. Laola tšebeliso ea hona joale (Alamo) ________________ A
• G. Nako ea alamo (Lihora; 15 Min. = 0.25 Hora) (Alamo) ________________ H
• H. Bokhoni ba betri bo hlokahalang bakeng sa Alamo (E+F)*G ________________ AH
• I. Kakaretso e lekantsoeng ea matla a betri D+H ________________ AH
• J. Bokhoni ba betri bo hlokahala I*1.8 (safety factor) ________________ AH

Hlokomela: AL1024NKA8(D) phepelo ea motlakase e etselitsoe ho sebetsa ka libeteri ho fihla ho 65AH. Ka kopo hlokomela: mola [I] ha oa tlameha ho feta 36AH.
U tlameha ho fokotsa tšebeliso ea hona joale kapa nako ea ho ema e le hore u ka ipapisa le tlhokahalo. Ho fumana boholo ba betri ka kopo, pota mohala [J] ho isa boholong bo tloaelehileng ba betri e haufinyane (mohlala 3.5 AH = 4.0 AH).

Litlhaloso

Kenyelletso:

• AL1024ULXB2:
  • 115VAC, 60Hz, 4.2A.
• ACMS8/ACMS8CB:
  • Litlhahiso tse robeli (8):
    • a) Ka tloaelo ho bula (NO) ho kenya (likhokahano tse omileng).
    • b) Ka tloaelo ho koetsoe (NC) (likhokahano tse omileng).
    • c) Bula lisebelisoa tsa sink ea pokello.
    • d) Keno e Metsi (5VDC - 24VDC) e nang le 10K resistor
    • e) Motsoako ofe kapa ofe oa tse ka holimo.

Liphetho:

• Matla:
  • 12VDC kapa 5VDC ho fihla ho 6A, 24VDC ho fihla ho 10A (240W kakaretso ea matla).
  • Ho tlolatagtshireletso.
• ACMS8:
  • Liphetho tse sirelelitsoeng ka fuse li behiloe @ 2.5A ka tlhahiso, e se nang matla a fokolang. Kakaretso ea tlhahiso 6A max. Se ke oa feta litekanyetso tsa phepelo ea motlakase ka bomong.
• ACMS8CB:
  • Liphetho tse sirelelitsoeng ke PTC li reiloe @ 2A ka tlhahiso, Sehlopha sa 2 se na le matla a fokolang. Kakaretso ea tlhahiso 6A max. Se ke oa feta litekanyetso tsa phepelo ea motlakase ka bomong.
  • Liphetho tse robeli (8) tse laoloang ka boikemelo kapa tse robeli (8) tse laoloang ka boikemelo tsa Foromo ea "C" (sheba ka tlase bakeng sa lintlha):
    • a) Fail-Sireletsehile le/kapa Fail-Sireletsehile diphetho tsa matla.
    • b) Li-relay tsa Foromo "C" li behiloe @ 2.5A. 12, 24VDC, 0.6 Power Factor (ACMS8 feela).
    • c) Lisebelisoa tsa motlakase tse thusang (tse sa fetoheng).
    • d) Motsoako ofe kapa ofe oa tse ka holimo.
• Liphetho tsa motho ka mong li ka hlophisoa ho OFF boemo bakeng sa ts'ebeletso (output jumper set to the middle). Ha e sebetse lits'ebetsong tsa Dry Contact.
• E fe kapa e fe ho tse robeli (8) tse fehlang motlakase tse sirelelitsoeng ke PTC li ka khethoa ho latela Motlakase oa Kenyeletso 1 kapa Input 2. Output voltage ea tlhahiso e 'ngoe le e 'ngoe e tšoana le matla a ho kenyatage ea tse kentsoeng.
• Khatello e phahameng.

Lintlha tsa Fuse/PTC:

• AL1024ULXB2:
  • Fuse e kentsoeng ke 5A/250V.
  • Fuse ea betri e lekantsoe 15A/32V.
• ACMS8:
  • Fuse ea mantlha e kenyellelitsoeng ho 15A/32V.
  • Li-fuse tse hlahisoang ke 3A/32V.
• ACMS8CB:
  • Kenyelletso ea mantlha PTC e fuoe lintlha tse 9A.
  • Li-PTC tse hlahisoang li fuoe lintlha tse 2A.

Boloka Battery:

• Tjhaja e hahelletsoeng kahare bakeng sa asiti e tiisitsoeng ea lead kapa libeteri tsa mofuta oa gel
• Jarolla ka ho iketsa ho ea stand-by betri ha AC hloleha.
• Boholo ba tefiso ea hajoale ke 3.6A.
• Leqhubu la Zerotage theoha ha e fetisetsoa ho bekapo ea betri.

Tlhokomelo:

• AC e hloleha ho laola (ho theha mabitso a "C").
• Tlhokomelo e tlase ea betri (ho theha mabitso a "C").
• Tlhokomelo ea boteng ba betri (foroha mabitso a "C").

Khaola Alarm ea Mollo:

• Ho khaoha ha Alarm ea Mollo (ho latching kapa ho se lache) ho ka khethoa ka bonngoe bakeng sa liphetho tse robeli (8). Likhetho tsa ho kenya Alarm ea Mollo:
  • a) Hangata e bula [NO] kapa hangata e koetsoe [NC] e omileng ea ho kenya. Kenyelletso ea ho khutlisa polarity ho tsoa ho potoloho ea matšoao a FACP.
• FACP input WET ke rated 5-30VDC 7mA.
• Ho kenya FACP EOL e hloka pheletso ea 10K ea mohanyetsi oa mohala.
• FACP output relay [NC]:
  Ekaba Dry 1A/28VDC, 0.6 Power Factor kapa 10K ho hanyetsa ka [EOL JMP] e tsitsitseng.

Matšoao a bonoang:

• AL1024ULXB2:
  • Green AC LED: E bonts'a 115VAC e teng.
  • Red DC LED: E bonts'a tlhahiso ea DC.
• ACMS8(CB):
  • Li-LED tse khubelu: Bontša hore liphetho li hlahisoa.
  • Blue LED: E bonts'a hore ho hakolloa ha FACP ho qalile.
  • Motho ka mong Voltage LEDs: Bontša 12VDC (Tala) kapa 24VDC (Red).

Tikoloho:

• Mocheso o sebetsang: 0ºC ho isa ho 49ºC tikolohong.
• Mongobo: 20 ho isa ho 85%, e sa fokotseng.

Kakaretso Dimensions (hoo e ka bang H x W x D): 15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm).

Litaelo tsa ho Hloma

Mekhoa ea ho kenya likhoele e tla tsamaellana le Khoutu ea Naha ea Motlakase/NFPA 70/NFPA 72/ANSI, Khoutu ea Motlakase ea Canada le likhoutu tsohle tsa lehae le ba boholong ba nang le matla a ho laola. Sehlahisoa se reretsoe ho sebelisoa ka tlung feela.

1. Beha yuniti sebakeng seo u se batlang. Tšoaea le ho phunya masoba leboteng ho tsamaisana le likoti tse peli tse ka holimo sebakeng se kampetsoeng. Kenya li-fasteners le li-screws tse peli leboteng 'me lihlooho tsa screw li hlahelle. Beha masoba a ka holimo a koaletsoeng holim'a likurufu tse peli tse ka holimo, u be boemong 'me u sireletsehe. Tšoaea boemo ba likoti tse peli tse tlase. Tlosa sebaka se kampetsoeng. Hlakola likoti tse tlase ebe u kenya li-fasteners tse peli. Beha masoba a ka holimo a kokelo holim'a likurufu tse peli tse ka holimo. Kenya li-screw tse peli tse tlase 'me u tiise hore u tiisa li-screw tsohle (Enclosure Dimensions, pg. 12). Sebaka se sireletsehileng sebakeng sa lefats'e.
2. Etsa bonnete ba hore li-jumpers tsohle tsa lihlahisoa [PWR1] - [PWR8] li behiloe sebakeng sa OFF (bohareng) (setšoantšo sa 1, leqephe la 3).
3. Hokela matla a AC a sa fetoheng (115VAC 60Hz) ho li-terminals tse tšoailoeng [L, N] (Setšoantšo sa 4a, leqephe la 5). Tala "AC" LED botong ea phepelo ea motlakase e tla bulela. Leseli lena le ka bonoa ka lense ea LED e monyako oa sebaka se kampetsoeng. Sebelisa 14 AWG kapa e kholoanyane bakeng sa likhokahano tsohle tsa matla. Sireletsehile terata e tala lebisa lefatšeng fatše. Boloka likhoele tse lekanyelitsoeng matla li arohane le lithapo tse se nang matla (115VAC 60Hz Input, Battery Wires). Bonyane sebaka sa sebaka sa 0.25" se tlameha ho fanoa.
   TLHOKOMELISO: U se ke ua tšoara likarolo tsa tšepe tse pepenene. Koala matla a potoloho ea lekala pele u kenya kapa u sebeletsa lisebelisoa. Ha ho na likarolo tse ka sebelisoang ke basebelisi kahare. Fetisetsa ho kenya le ho fana ka litšebeletso ho basebeletsi ba nang le tsebo.
4. Beha sehlahisoa se seng le se seng [OUT1] - [OUT8] ho tsamaisa matla a tsoang ho Input 1 kapa 2 (setšoantšo sa 1, pg. 3).
   Hlokomela: Lekanya tlhahiso voltage pele o kopanya lisebelisoa. Sena se thusa ho qoba tšenyo e ka bang teng.
5. Tima motlakase pele o hokela lisebelisoa.
6. Likhetho tsa tlhahiso: AL1024NKA8(D) e tla fana ka liphetho tse fihlang ho tse robeli (8) tsa matla a fetotsoeng kapa liphetho tse robeli (8) tse omeletseng tsa "C", kapa motsoako ofe kapa ofe oa matla a fetotsoeng le liphetho tsa "C", le tse robeli (8) tse sa fetoheng. lisebelisoa tse thusang.
   • Liphetoho tsa Power tse fetotsoeng:
     Hokela molaetsa o fosahetseng (–) oa sesebelisoa se tsamaisoang ho terminal e tšoailoeng [COM].
     • Bakeng sa ts'ebetso ea Fail-Safe, hokela molaetsa o nepahetseng (+) oa sesebelisoa se tsamaisoang ho theminale e tšoailoeng [NC].
     • Bakeng sa ts'ebetso ea Fail-Sireletsehile, hokela ho kenya letsoho (+) ho sesebelisoa se tsamaisoang ho terminal e tšoailoeng [NO].
   • Liphetho tsa foromo ea "C":
     Ha lihlahisoa tsa "C" li lakatseha, jumper e lumellanang (1-8) e tlameha ho behoa sebakeng sa OFF (setšoantšo sa 7, leqepheng la 9). Ntle le moo, fuse e lumellanang ea tlhahiso (1-8) e ka tlosoa (AL1024NKA8 feela). Hokela negative (–) ea phepelo ea motlakase ka kotloloho ho sesebelisoa sa ho notlela. Hokela positi (+) ea phepelo ea motlakase ho theminale e tšoailoeng [C].
     • Bakeng sa ts'ebetso ea Fail-Safe, hokela positi (+) ea sesebelisoa se tsamaisoang ho theminale e tšoailoeng [NC].
     • Bakeng sa ts'ebetso ea Fail-Sireletsehile hokela positi (+) ea sesebelisoa se tsamaisoang ho theminale e tšoailoeng [NO]. Mabitso a omileng a rated @ 2.5A, 28VDC.
   • Lisebelisoa tsa Matla a Thusang (tse sa fetoloang):
     Hokela sesebediswa se nepahetseng (+) se sebediswang ho theminale e ngotsweng [C] le negative (–) ya sesebediswa se tsamaisoang ho theminale e ngotsweng [COM]. Sephetho se ka sebelisoa ho fana ka matla bakeng sa babali ba likarete, li-keypad joalo-joalo.
7. Laeta motlakase oa mantlha ka mor'a hore lisebelisoa tsohle li hoketsoe.
8. Likhetho tsa Input Trigger:
   
   Hlokomela: Haeba ho khaoha ha Alarm ea Mollo ho sa sebelisoe, hokela sehanyetsi sa 10K ohm ho litheminale tse tšoailoeng [GND le EOL], 'me u hokele jumper ho litheminale tse tšoailoeng [GND, RST].
   Ka tloaelo Bula (NO) Kenyo:
   Theeletso ya taolo ya selaete ya logic DIP e fetohela ho OFF bakeng sa [Fetosa 1-8] (setšoan. 2, ka ho le letona). Hokela mehala ea hau ho litheminale tse tšoailoeng [+ INP1 –] ho [+ INP8 –].
   Keletso e Tlwaelehileng (NC):
   Theeletso ya taolo ya selaete ya logic DIP e fetohela boemong ba ON bakeng sa [Switch 1-8] (Figure 2, ka ho le letona). Hokela mehala ea hau ho litheminale tse tšoailoeng [+ INP1 –] ho [+ INP8 –].
   Bula Kenyelletso ea Sink ea Collector:
   Hokela sink e bulehileng ea pokello ea metsi ho theminale e tšoailoeng [+ INP1 –] ho [+ INP8 –].
   Metsi (Moqtage) Tlhophiso ea Kenyeletso:
   Ho shebella ka hloko polarity, hokela voltage input trigger wires le 10K resistor e fanoeng ho li-terminals tse tšoailoeng [+ INP1 –] ho [+ INP8 –].
   Haeba o sebelisa voltage ho qala ho kenya - seta phetoho e lumellanang ea INP Logic sebakeng sa "OFF".
   Haeba ho tlosa voltage ho qala ho kenya - beha phetoho e lumellanang ea INP Logic sebakeng sa "ON".
9. Likhetho tsa Sehokelo sa Alarm ea Mollo:
   
   [NC] eo hangata e koetsoeng, eo hangata e bulang [NO] kapa keno e khutlisang polarity ho tsoa ho potoloho ea matšoao ea FACP e tla hlahisa likhetho tse khethiloeng. Ho nolofalletsa FACP Disconnect bakeng sa tlhahiso, bulela switch e tsamaellanang le DIP [SW1-SW8]. Ho tima FACP hakoa bakeng sa tlhahiso, tima switch e tsamaellanang ea DIP [SW1-SW8] TIMA. Switch e fumaneha ka ho toba ka letsohong le letšehali la Fire Alarm Interface Terminals.
   Ka tloaelo Bula Kenyo:
   Kopanya relay ea hau ea FACP le sehanyetsi sa 10K ka 'moho ho litheminale tse tšoailoeng [GND] le [EOL].
   Kenyelletso e Tloaelehileng:
   Kopanya relay ea hau ea FACP le sehanyetsi sa 10K ho litheminale tse tšoailoeng [GND] le [EOL].
   Sehlomathisi sa Potoloho sa Potoloho sa Letshwao la FACP:
   Hokela positive (+) le negative (–) ho tloha ho FACP signaling circuit output ho litheminale tse tšoailoeng [+ FACP –]. Hokela FACP EOL ho li-terminals tse tšoailoeng [+ RET –] (polarity e hlalositsoe boemong ba alamo).
   Ho Khaolla Alamo ea Mollo e sa Chesang: Hokela jumper ho litheminale tse tšoailoeng [GND, RST].
10. FACP Dry NC tlhahiso:
    Hokela sesebediswa se lakatsehang se tla susumetswa ke yuniti e ommeng ya kgokahano ho ditheminale tse ngotsweng [NC] le [C]. Ha [EOL JMP] e bolokiloe e tiile, tlhahiso ke ea 0 Ohm ho hanyetsa boemong bo tloaelehileng. Ha [EOL JMP] e koetsoe, khanyetso ea 10k e tla fetisetsoa sesebelisoa se latelang ha e le boemong bo tloaelehileng.
11. Likhokahano tsa Battery tse Emeng (Setšoantšo sa 6, leqephe la 8):
    Bakeng sa lits'ebetso tsa US Access Control li-betri lia ikhethela. Libetri lia hlokahala bakeng sa ho kenya lisebelisoa tsa Canada (ULC-S319). Ha libetri li sa sebelisoe, tahlehelo ea AC e tla fella ka tahlehelo ea matla a tlhahisotage. Ha tšebeliso ea libeteri tse emeng li lakatseha, e tlameha ho ba acid ea lead kapa mofuta oa gel. Kopanya betri ho li-terminals tse tšoailoeng [- BAT +] (Setšoantšo sa 4g, leqephe la 6). Sebelisa libeteri tse peli (2) tsa 12VDC tse hokahaneng letotong bakeng sa ts'ebetso ea 24VDC (li-lead tsa betri li kenyelelitsoe). Sebelisa libeteri – Casil CL1270 (12V/7AH), CL12120 (12V/12AH), CL12400 (12V/40AH), CL12650 (12V/65AH) libeteri kapa libeteri tse amoheloang ke UL BAZR2 le BAZR8 tsa lintlha tse nepahetseng.
12. Liphetho tsa Battery le AC Supervision (Setšoantšo sa 4, leqephe la 8):
    Hokela lisebelisoa tse nepahetseng tsa tsebiso ho litheminale tse tšoailoeng [AC FAIL & BAT FAIL] (Fig. 4b, pg. 5) liphetho tsa phepelo ea tlhokomelo. Sebelisa 22 AWG ho isa ho 18 AWG bakeng sa tlaleho ea AC Fail & Low/No Bettery.
13. Ho lieha ho tlaleha ho fihlela lihora tse 6., Khaola "AC Delay" jumper 'me u tsosolose matla ho unit (setšoantšo sa 4f, pg. 6).
14. Ho Khaola Alamo ea Mollo (Setšoantšo sa 4c, leqephe la 6):
    • Ho bulela Alamo ea Mollo Hakolla, seta switjha ea DIP [Shutdown] ho ea ho ON.
    • Ho tima Alamo ea Mollo Hakolla seta switjha ea DIP [Shutdown] ho ea ho OFF.
15. Ho kenngoa ha tamper switch:
    Thaba ea UL Listed tamper switch (Altronix ea mohlala TS112 kapa e lekanang le eona) ka holimo ho sebaka se kampetsoeng. Tsamaisa tamper switjha bracket moeling oa sebaka se koaletsoeng hoo e ka bang 2 "ho tloha ka lehlakoreng le letona (setšoantšo sa 6a, leqephe la 8). Kopanya tamper switch wiring ho kena ho Access Control Panel kapa sesebelisoa se nepahetseng sa tlaleho se Lethathameng la UL. Ho kenya tshebetsong letshwao la alamo bula lemati la kampere.

Tlhokomelo

Yuniti e lokela ho lekoa bonyane hang ka selemo bakeng sa ts'ebetso e nepahetseng ka tsela e latelang:

• Khumo Voltage Teko: Tlas'a maemo a tloaelehileng a moroalo DC output voltage lokela ho hlahlojwa bakeng sa vol e nepahetsengtagboemo ba.
• Teko ea Betri: Tlas'a maemo a tloaelehileng a mojaro, hlahloba hore na betri e tjhajiloe ka botlalo, hlahloba molumo o boletsoengtage ka bobeli boemelong ba betri le liteisheneng tsa boto tse tšoailoeng [- BAT +] ho netefatsa hore ha ho na ho khaoha lithapong tsa ho hokela betri.

Hlokomela: Nako e phahameng ea ho tjhaja ha e tsoa ke 3.6A.
Hlokomela: Bophelo ba betri bo lebelletsoeng ke lilemo tse 5; leha ho le joalo, ho khothalletsoa ho fetola libeteri ka lilemo tse 4 kapa ka tlase ha ho hlokahala

Setšoantšo sa 4 - AL1024ULXB2 Tlhophiso ea Boto

 

Lisebelisoa tsa LED

AL1024ULXB2 - Boto ea Phepelo ea Matla 

Khubelu (DC)	Botala (AC)	Boemo ba Phepelo ea Matla
ON	ON	Boemo bo tloaelehileng ba ts'ebetso.
ON	TLOA	Tahlehelo ea AC. Betri e emeng haufi e fana ka matla.
TLOA	ON	Ha ho tlhahiso ea DC.
TLOA	TLOA	Tahlehelo ea AC. Betri e emeng kapa e sa sebetseng. Ha ho tlhahiso ea DC.

ACMS8 le ACMS8CB Access Power Controller 

LED	ON	TLOA
LED 1- LED 8 (Khubelu)	Li-relay li feletsoe ke matla.	Li-relay tse hlahisoang li matlafalitsoe.
FACP	Ho kenya FACP (boemo ba alamo).	FACP e tloaelehileng (boemo boo e seng alamo).
Sephetho se Setala 1-8	12VDC	–
Sephetho se Sefubelu 1-8	24VDC	–

Boitsebiso ba Terminal

AL1024ULXB2 - Boto ea Phepelo ea Matla 

Terminal Taba	Mosebetsi/Tlhaloso
L, N	Hokela 115VAC ho li-terminals tsena: L ho ea ho chesa, N ho se nke lehlakore (Feie. 4a, leq. 6).
+ DC -	Feme e hokahantsoeng le ACMS8(CB) (Feie. 4d, leq. 6).
AC Fail NC, C, NO	E sebedisetswa ho tsebisa tahlehelo ya matla a AC, mohlala, ho hokela sesebedisweng se utlwahalang kapa phanele ya alamo. Relay hangata e matlafatsoa ha matla a AC a le teng. Contact rating 1A @ 28VDC. AC kapa brownout failure e tlalehoa nakong ea motsotso o le mong oa ketsahalo. Ho lieha ho tlaleha ho fihlela lihora tse 6., khaola "AC Delay" jumper 'me u tsosolose matla ho unit. (Feie. 4f, leq. 6).
Bat Fail NC, C, NO	E sebedisetswa ho bontsha boemo ba betri e tlase, mohlala, hokela phanele ya alamo. Relay hangata e matlafatsoa ha matla a DC a le teng. Contact rating 1A @ 28VDC. Betri e tlositsoeng e tlalehoa nakong ea motsotso o le mong. Khokahano ea betri e tlaleheloa nakong ea motsotso o le mong. Boemo ba betri bo tlase: hoo e ka bang 21VDC (Setšoantšo sa 4b, leqephe la 6).
– BAT +	Lihokelo tsa betri tse emeng. Boholo ba tefiso ea hajoale 3.6A (Feie. 4c, leq. 6).

ACMS8 le ACMS8CB Access Power Controller 

Terminal Taba	Mosebetsi/Tlhaloso
+ PWR1 -	Feme e hokahantsoeng le AL1024ULXB2. Se ke oa sebelisa li-terminals tsena.
+ PWR2 -	Feme e hokahantsoeng le VR6 voltage regulator. Se ke oa sebelisa li-terminals tsena.
+ INP1 - ka + INP8 -	Tse robeli (8) tse laoloang ka boikemelo Normally Open (NO), Ka tloaelo Ho Koetsoe (NC), Open Collector Sink kapa Wet Input Triggers.
C, NC	Phatlalatso ea FACP Dry NC rated 1A/28VDC @ 0.6 Power Factor. Sehlopha sa 2 se na le matla a fokolang. Ka EOL JMP e tiile, e tla fana ka khanyetso ea 10k maemong a tloaelehileng.
GND, RST	FACP segokanyimmediamentsi sa sebolokigolo latching kapa e seng latching. HA HO se kentsoeng se ommeng. Sehlopha sa 2 se na le matla a fokolang. E tla khutsufatsoa bakeng sa sebopeho sa FACP se sa ts'oanelang kapa Latch FACP reset.
GND, EOL	EOL E hlokometseng liteishene tsa ho Kena tsa FACP bakeng sa ts'ebetso ea polarity ea ho khutlisa FACP. Sehlopha sa 2 se na le matla a fokolang.
- F, + F, - R, + R	FACP Signaling Circuit Input and Return terminals. Sehlopha sa 2 se na le matla a fokolang.
Sehlahisoa 1 ka Sephetho sa 8 NO, C, NC, COM	Liphetho tse robeli (8) tse laoloang ka boikemelo [Fail-Safe (NC) kapa Fail-Secure (NO)] le tse robeli (8) tse laoloang ka boikemelo tsa Foromo ea "C" Relay.

Setšoantšo sa 6 - AL1024NKA8(D)

TLHOKOMELISO: Sebelisa libeteri tse emeng tse peli (2) 12VDC.

• Boloka lithapo tse lekanyelitsoeng matla li arohane le tse se nang matla. Sebelisa sebaka sa bonyane sa 0.25”.
• 12AH Libetri tse ka chachang hape ke libeteri tse kholo ka ho fetisisa tse ka kenang ka har'a sebaka sena se kampetsoeng.
• Sebaka sa betri sa kantle se thathamisitsoeng ka UL se tlameha ho sebelisoa ha ho sebelisoa libeteri tsa 40AH kapa 65AH.

Setšoantšo se Tloaelehileng sa Kopo

Hook-Up Diagrams

• Setšoantšo sa 8 - Daisy-chaining unit e le 'ngoe kapa ho feta ACMS8(CB). EOL Jumper [EOL JMP] e lokela ho kenngoa boemong ba EOL. E sa Lateng.
  
• Setšoantšo sa 9 - Daisy-chaining unit e le 'ngoe kapa ho feta ACMS8(CB). EOL Jumper [EOL JMP] e lokela ho kenngoa boemong ba EOL. Latching Single Reset.
  
• Setšoantšo sa 10 - Daisy e kopanya lihlopha tse le 'ngoe kapa tse ngata tsa ACMS8(CB). EOL Jumper [EOL JMP] e lokela ho kenngoa boemong ba EOL. Latching Individual Reset.
  

Hook-Up Diagrams

• Setšoantšo sa 11 - Polarity reversal input ho tloha FACP signaling circuit output (polarity e hlalosoa ka boemo ba alamo). E sa Lateng
  
• Setšoantšo sa 12 - Polarity reversal input ho tloha FACP signaling circuit output (polarity e hlalosoa ka boemo ba alamo). Latching
  
• Setšoantšo sa 13 - Ka tloaelo ho Koetsoe ho kenya trigger (Non-Latching).
  
• Setšoantšo sa 14 - Ka tloaelo ho Koetsoe ho kenya letsoho (Latching).
  
• Setšoantšo sa 15 - Ka tloaelo Open trigger input (Non-Latching)
  
• Setšoantšo sa 16 - Ka tloaelo Open trigger input (Latching).
  

Bophahamo ba Khokahano (BC400)

15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm)

Altronix ha e ikarabelle bakeng sa liphoso leha e le life tsa typographical. 140 58th Street, Brooklyn, New York 11220 USA

• mohala: 718-567-8181
• fekse: 718-567-9056
• websebaka: www.altelengx.com
• lengolo-tsoibila: info@altronix.com
• Warranty ea bophelo bohle

Litokomane / Lisebelisoa

Altronix AL1024NKA8 Letoto la Litaolo tsa Matla a Mabeli a Liphello tse Hlahang [pdf] Tlhophiso Tataiso AL1024NKA8, AL1024NKA8D, AL1024NKA8 Series Balaoli ba Matla a ho kena habedi, Balaoli ba Matla a ho kena habedi, ba laolang matla a ho kena, ba laolang matla a mabeli a tsoang, ba laolang matla.

Litšupiso

• Bukana ea Mosebelisi