Altronix AL1024NKA8 Series Dual Output Access Power Controllers

Zathaview

Altronix AL1024NKA8 ndi AL1024NKA8D amagawa ndikusintha mphamvu kuti apeze machitidwe olamulira ndi zipangizo. Amasintha cholowetsa cha 115VAC 60Hz kukhala zotuluka zisanu ndi zitatu (8) zoyendetsedwa paokha 12VDC kapena 24VDC zotetezedwa. Mapangidwe apawiri a Access Power Controller amalola mphamvu kutsogozedwa kuchokera ku ma voliyumu awiri (2) okhazikitsidwa ndi fakitale odziyimira pawokha.tage 12 kapena 24VDC Altronix magetsi kwa asanu ndi atatu (8) oyendetsedwa pawokha fuse (AL1024NKA8) kapena PTC (AL1024NKA8D) zotuluka zotetezedwa. Zotulutsa mphamvu zitha kusinthidwa kukhala mawonekedwe owuma "C". Zotulutsa zimayatsidwa ndi sinki yotsegulira yotsegulira, yomwe nthawi zambiri imatsegulidwa (NO), yomwe nthawi zambiri imatsekedwa (NC) choyambitsa chowuma, kapena chonyowa kuchokera ku Access Control System, Card Reader, Keypad, Push Button, PIR, ndi zina zotero. AL1024NKA8(D) mphamvu ya njira yopita ku zipangizo zosiyanasiyana zoyendetsera zipangizo za hardware kuphatikizapo Mag Locks, Kumenya Magetsi, Magnetic Door Holders, ndi zina zotero. Zotuluka zidzagwira ntchito zonse Zolephera-Safe ndi / kapena Fail-Secure modes. FACP Interface imathandizira Emergency Egress, Alarm Monitoring, kapena ingagwiritsidwe ntchito kuyambitsa zida zina zothandizira. Cholumikizira alamu yamoto chimasankhidwa payekhapayekha pazotsatira zilizonse zisanu ndi zitatu (8). Zolumikizira za spade zimakulolani kuti muzitha kulumikiza mphamvu zama module angapo a ACMS8(CB). Izi zimakupatsani mwayi wogawa mphamvu pazotulutsa zambiri pamakina akuluakulu.

Zoyimira Pamodzi (zonse zomwe zikuwonetsedwa)

Zotulutsa	15 min. ya Stand-by ndi 5 min. ya Alamu	4 hr. ya Stand-by ndi 5 min. ya Alamu	24h. ya Stand-by ndi 5 min. ya Alamu	60h. ya Stand-by ndi 5 min. ya Alamu
24VDC/12AH Batiri	Stand-By = 8A Alamu = 10A	Stand-By = 1.5A Alamu = 10A	Stand-By = 200mA Alamu = 10A	Stand-By = 100mA Alamu = 10A
Zotulutsa	15 min. ya Stand-by ndi 5 min. ya Alamu	4 hr. ya Stand-by ndi 5 min. ya Alamu	24 hr. ya Stand-by ndi 15 min. ya Alamu	60 hr. ya Stand-by ndi 15 min. ya Alamu
24VDC/65AH Batiri	–	Stand-By = 8.0A Alamu = 10A	Stand-By = 1.5A Alamu = 10A	Stand-By = 500mA Alamu = 10A

Kwa mapulogalamu a Access Control, mphamvu ya batri ya 10A yopereka panopa - 1 hr. kwa batire ya 24VDC/12AH, maola 6.5. kwa batire ya 24VDC/65AH. Onani tsamba lowerengera kukula kwa batri pansipa la mabatire ena.

• A. AL1024NKA8(D) kagwiritsidwe kake mkati (kuyimilira) ________________ 0.05 A
• B. Katundu waposachedwa (kuyimirira) ________________ A
• C. Nthawi yofunikira (maola) ________________ H
• D. Kuchuluka kwa batri kumafunika poyimirira (A+B)*C ________________ AH
• E. AL1024NKA8(D) kugwiritsa ntchito mphamvu mkati (Alamu) ________________ 0.05 A
• F. Katundu waposachedwa (Alamu) ________________ A
• G. Nthawi ya alamu (Maola; 15 Min. = 0.25 Ola) (Alamu) ________________ H
• H. Mphamvu ya batri yofunikira pa Alamu (E+F)*G ________________ AH
• I. Batire yonse yowerengeredwa ndi D+H ________________ AH
• J. Kuchuluka kwa batri kumafunika I*1.8 (chitetezo chachitetezo) ________________ AH

Zindikirani: AL1024NKA8(D) magetsi adapangidwa kuti azigwira ntchito ndi mabatire mpaka 65AH. Chonde dziwani: mzere [I] usapitirire 36AH.
Muyenera kuchepetsa zomwe mukugwiritsa ntchito panopa kapena nthawi yoyimilira kuti mugwirizane ndi zofunikira. Kuti mudziwe kukula kwenikweni kwa batire chonde mzere wozungulira [J] kupita ku batire yapafupi yokulirapo (monga 3.5 AH = 4.0 AH).

Zofotokozera

Zolowa:

• Chithunzi cha AL1024ULXB2
  • 115VAC, 60Hz, 4.2A.
• ACMS8/ACMS8CB:
  • Zoyambitsa zisanu ndi zitatu (8):
    • a) Nthawi zambiri otsegula (NO) zolowetsa (zowuma).
    • b) Nthawi zambiri zotsekedwa (NC) (zowuma).
    • c) Tsegulani zolowetsa zokokera.
    • d) Kulowetsa Konyowa (5VDC - 24VDC) yokhala ndi 10K resistor
    • e) Kuphatikiza kulikonse kwa pamwamba.

Zotuluka:

• Mphamvu:
  • 12VDC kapena 5VDC mpaka 6A, 24VDC mpaka 10A (240W okwana mphamvu).
  • Kupambanatage chitetezo.
• ACMS8:
  • Zotulutsa zotetezedwa ndi fuse zidavotera @ 2.5A pazotulutsa, zopanda mphamvu. Zotulutsa zonse 6A max. Osapitilira mavoti amagetsi amunthu payekha.
• ACMS8CB:
  • Zotulutsa zotetezedwa ndi PTC zidavotera @ 2A pachotulutsa chilichonse, Gulu lachiwiri lopanda mphamvu. Zotulutsa zonse 2A max. Osapitilira mavoti amagetsi amunthu payekha.
  • Zotuluka zisanu ndi zitatu (8) zosankhidwa paokha kapena zotuluka zisanu ndi zitatu (8) zoyendetsedwa modziyimira pawokha za Fomu "C" (onani pansipa kuti mupeze mavoti):
    • a) Kulephera-Safe ndi/kapena Kulephera-Safe mphamvu zotuluka.
    • b) Mafomu a "C" adavotera @ 2.5A. 12, 24VDC, 0.6 Power Factor (ACMS8 yokha).
    • c) Zowonjezera mphamvu zowonjezera (zosasinthika).
    • d) Kuphatikiza kulikonse kwa pamwamba.
• Zotulutsa zapayekha zitha kukhazikitsidwa kuti ZIZIMU pothandizira (chodumpha chotulutsa chakhazikitsidwa pamalo apakati). Sizikugwira ntchito ku Dry Contact application.
• Chilichonse mwa zisanu ndi zitatu (8) zotuluka za fuse/PTC-zotetezedwa ndizosankhika kuti zitsatire mphamvu Kulowetsa 1 kapena Kulowetsa 2. Kutulutsa mphamvutage ya zotulutsa zilizonse ndizofanana ndi voliyumu yoloweratage za zomwe zasankhidwa.
• Kuchepetsa kuthamanga.

Mavoti a Fuse/PTC:

• Chithunzi cha AL1024ULXB2
  • Fuse yolowetsa idavotera 5A/250V.
  • Fuse ya batri idavotera 15A/32V.
• ACMS8:
  • Fuse yayikulu yolowera idavotera 15A/32V.
  • Ma fuse otulutsa adavotera 3A/32V.
• ACMS8CB:
  • Cholowa chachikulu cha PTC chidavotera 9A.
  • Ma PTC otuluka adavotera 2A.

Kusunga Battery:

• Thumba loyikirapo la asidi osindikizidwa kapena mabatire amtundu wa gel.
• Makinawa sinthani kuti muyime-batire pomwe AC yalephera.
• Malipiro apamwamba kwambiri 3.6A.
• Zero voltage dontho pamene kusintha kwa batire zosunga zobwezeretsera.

Kuyang'anira:

• AC yalephera kuyang'anira (ma fomu "C").
• Kuyang'anira batire yocheperako (mawu amtundu wa "C").
• Kuyang'anira kupezeka kwa batri (ma fomu "C").

Chotsani Alamu ya Moto:

• Kulumikizika kwa Alamu ya Moto (kutchingira kapena kusayakira) kumasankhidwa payekhapayekha pazotulutsa zilizonse kapena zonse zisanu ndi zitatu (8). Zosankha zolowetsa za Alamu yamoto:
  • a) Nthawi zambiri amatsegula [NO] kapena amatseka [NC] zolumikizira zowuma. Kusintha kwa polarity kuchokera kudera losainira la FACP.
• Kulowetsa kwa FACP WET kudavotera 5-30VDC 7mA.
• Kulowetsa kwa FACP EOL kumafuna 10K kutha kwa mzere wotsutsa.
• FACP linanena bungwe relay [NC]:
  Mwina Dry 1A/28VDC, 0.6 Power Factor kapena 10K kukana ndi [EOL JMP] yosasunthika.

Zizindikiro Zowoneka:

• Chithunzi cha AL1024ULXB2
  • Green AC LED: Imawonetsa 115VAC ilipo.
  • Red DC LED: Ikuwonetsa kutulutsa kwa DC.
• ACMS8(CB):
  • Ma LED Ofiyira: Onetsani zotulukapo zayambika.
  • Blue LED: Imawonetsa kuti kulumikizidwa kwa FACP kwayambika.
  • Munthu payekha Voltagma LED: Onetsani 12VDC (Green) kapena 24VDC (Yofiira).

Zachilengedwe:

• Kutentha kwa ntchito: 0ºC mpaka 49ºC mozungulira.
• Chinyezi: 20 mpaka 85%, osasunthika.

Miyeso Yampanda (pafupifupi H x W x D): 15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm).

Malangizo oyika

Njira zama waya zizikhala molingana ndi National Electrical Code/NFPA 70/NFPA 72/ANSI, Canadian Electrical Code komanso ma code onse amderali ndi maulamuliro omwe ali ndi ulamuliro. Zogulitsazo zimangogwiritsidwa ntchito m'nyumba zokha.

1. Mount unit pamalo omwe mukufuna. Chongani ndi kubowola zibowo pakhoma kuti mufanane ndi mabowo awiri apamwamba m'khomamo. Ikani zomangira ziwiri zam'mwamba ndi zomangira pakhoma ndi mitu ya wononga yotuluka. Ikani mabowo am'mwamba a mpanda pamwamba pa zomangira ziwiri zakumtunda, mulingo ndi motetezeka. Lembani malo a mabowo awiri apansi. Chotsani mpanda. Boolani mabowo apansi ndikuyika zomangira ziwiri. Ikani mabowo a makiyi apamwamba pamwamba pa zomangira ziwiri zakumtunda. Ikani zomangira ziwiri zapansi ndikuonetsetsa kuti mukungitsa zomangira zonse (Enclosure Dimensions, pg. 12). Malo otetezedwa ku nthaka pansi.
2. Onetsetsani kuti ma jumpers onse otulutsa [PWR1] - [PWR8] aikidwa pa OFF (pakati) malo (Mkuyu 1, p. 3).
3. Lumikizani mphamvu ya AC yosasinthika (115VAC 60Hz) ku malo olembedwa [L, N] (Mkuyu 4a, pg. 5). Green "AC" LED pa bolodi lamagetsi idzayatsidwa. Kuwala uku kumatha kuwonedwa kudzera mu lens ya LED yomwe ili pachitseko cha mpanda. Gwiritsani ntchito 14 AWG kapena kukulirapo pamalumikizidwe onse amagetsi. Mawaya obiriwira otetezedwa amatsogolera ku nthaka pansi. Sungani mawaya opanda mphamvu osiyana ndi mawaya opanda mphamvu (115VAC 60Hz Input, Mawaya a Battery). Malo osachepera 0.25" ayenera kuperekedwa.
   CHENJEZO: Osagwira zitsulo zowonekera. Tsekani mphamvu yoyendera nthambi musanayike kapena kutumizira zida. Palibe magawo omwe angagwiritsidwe ntchito mkati. Bweretsani kuyika ndi kutumiza kwa ogwira ntchito oyenerera.
4. Khazikitsani zotsatira zilizonse [OUT1] - [OUT8] kuti muyendetse mphamvu kuchokera ku Input 1 kapena 2 (mkuyu 1, pg. 3).
   Zindikirani: Yesani zotuluka voltage pamaso kulumikiza zipangizo. Izi zimathandiza kupewa kuwonongeka komwe kungachitike.
5. Zimitsani magetsi musanalumikize zida.
6. Zosankha zotulutsa: AL1024NKA8(D) ipereka mphamvu zosinthira zisanu ndi zitatu (8) kapena zotuluka zisanu ndi zitatu (8) zowuma za "C", kapena kuphatikiza mphamvu zonse ziwiri ndi mawonekedwe a "C", kuphatikiza zisanu ndi zitatu (8) zosasinthika. zowonjezera mphamvu zotulutsa.
   • Kusintha kwa Power outputs:
     Lumikizani zosokoneza (-) za chipangizo chomwe chikugwiritsidwa ntchito ku terminal yolembedwa [COM].
     • Kuti mugwire ntchito ya Fail-Safe, gwirizanitsani zolowetsa zabwino (+) za chipangizo chomwe chikugwiritsidwa ntchito ku terminal yolembedwa [NC].
     • Kuti mugwiritse ntchito Fail-Secure, gwirizanitsani zolowetsa zabwino (+) za chipangizo chomwe chikugwiritsidwa ntchito ku terminal yolembedwa [NO].
   • Zotsatira za Fomu "C":
     Pamene mawonekedwe a "C" akufunidwa, jumper yofanana (1-8) iyenera kuikidwa pa OFF malo (Mkuyu 7, p. 9). Kapenanso, fuse yofananira (1-8) imatha kuchotsedwa (AL1024NKA8 yokha). Lumikizani zoipa (-) za magetsi molunjika ku chipangizo chotseka. Lumikizani zabwino (+) za magetsi ku terminal yolembedwa [C].
     • Kuti mugwire ntchito ya Fail-Safe, lumikizani zabwino (+) za chipangizocho chomwe chili ndi cholembera [NC].
     • Kuti mugwiritse ntchito Fail-Secure, lumikizani zabwino (+) za chipangizocho chomwe chili ndi cholembera [NO]. Zouma zowuma zidavotera @ 2.5A, 28VDC.
   • Zowonjezera Mphamvu Zowonjezera (zosasinthika):
     Lumikizani zolowetsa zabwino (+) za chipangizocho chomwe chili ndi cholembera [C] ndi choyipa (-) cha chipangizocho chomwe chili ndi cholembera [COM]. Zotulutsa zitha kugwiritsidwa ntchito kupereka mphamvu kwa owerenga makhadi, ma keypad etc.
7. Yatsani mphamvu yayikulu zida zonse zikalumikizidwa.
8. Zosankha Zoyambitsa Zolowetsa:
   
   Zindikirani: Ngati kulumikizidwa kwa Alamu ya Moto sikunagwiritsidwe ntchito, lumikizani chopinga cha 10K ohm ku matheminali olembedwa [GND ndi EOL], ndipo mulumikizeni chodumphira ku matheminali olembedwa [GND, RST].
   Nthawi zambiri Zolowetsa Zotsegula (NO):
   Sinthani mawu owongolera a DIP kukhala OFF pa [Sinthani 1-8] (mkuyu 2, kumanja). Lumikizani mawaya anu kumaterminal olembedwa [+ INP1 –] ku [+ INP8 –].
   Zolowetsa Nthawi Zonse (NC):
   Sinthani mawu olowera a DIP kukhala ON pa [Sinthani 1-8] (mkuyu 2, kumanja). Lumikizani mawaya anu kumaterminal olembedwa [+ INP1 –] ku [+ INP8 –].
   Tsegulani Zolowetsa Zosonkhanitsa:
   Lumikizani zolowetsa zotsegulira zolowera ku terminal yolembedwa [+ INP1 –] ku [+ INP8 –].
   Madzi (Voltage) Kusintha Kolowetsa:
   Poyang'anitsitsa polarity, gwirizanitsani voltagmawaya oyambitsa ma e input ndi cholumikizira cha 10K choperekedwa kumatheminali cholembedwa [+ INP1 –] kupita ku [+ INP8 –].
   Ngati kugwiritsa ntchito voltage kuti muyambitse zolowetsa - ikani kusintha kofananira kwa INP Logic kupita ku "OFF".
   Ngati kuchotsa voltage kuti muyambitse zolowetsa - ikani chosinthira chofananira cha INP Logic kupita pa "ON".
9. Zosankha za Fire Alarm Interface:
   
   [NC] yomwe imakhala yotsekedwa, yomwe nthawi zambiri imatsegula [NO] kapena kusintha kwa polarity kuchokera kumagawo osayina a FACP kumayambitsa zotulukapo zosankhidwa. Kuti mutsegule FACP Disconnect kuti mutuluke yatsani chosinthira cha DIP [SW1-SW8] WOYATSA. Kuti mulepheretse kulumikizidwa kwa FACP kuti mutuluke, yatsani chosinthira cha DIP chofananiracho [SW1-SW8] ZIMIMI. Switch ili kumanzere kwa Fire Alarm Interface Terminals.
   Nthawi zambiri Zolowetsa Zotsegula:
   Yambani mawaya anu a FACP relay ndi 10K resistor XNUMXK mofananira pamatheminali olembedwa [GND] ndi [EOL].
   Zomwe Zimatsekedwa Nthawi zambiri:
   Yambani mawaya anu a FACP relay ndi 10K resistor XNUMXK pamndandanda pamaterminal olembedwa [GND] ndi [EOL].
   Choyambitsa Cholowetsa Chiwonetsero cha FACP:
   Lumikizani zabwino (+) ndi zoipa (-) kuchokera ku FACP yotulutsa siginecha kupita ku ma terminals olembedwa [+ FACP -]. Lumikizani FACP EOL ku matheminali olembedwa [+ RET –] (polarity imatchulidwa ngati alamu).
   Ma Alamu Amoto Osayatsidwa: Lumikizani cholumphira kumalo otchedwa [GND, RST].
10. FACP Dry NC zotuluka:
    Lumikizani chipangizo chomwe mukufuna kuti chiyambitsidwe ndi cholumikizira chowuma cha unit ku ma terminals olembedwa [NC] ndi [C]. [EOL JMP] ikasungidwa bwino, zotulutsa zake zimakhala za 0 Ohm kukana mumkhalidwe wabwinobwino. [EOL JMP] ikadulidwa, kukana kwa 10k kumaperekedwa ku chipangizo china chikakhala bwino.
11. Kulumikizitsa Battery Yoyimirira (mkuyu 6, tsamba 8):
    Kwa mapulogalamu a US Access Control mabatire ndi osankha. Mabatire amafunikira pakukhazikitsa ku Canada (ULC-S319). Mabatire akapanda kugwiritsidwa ntchito, kutayika kwa AC kumapangitsa kuti mphamvu yamagetsi iwonongeketage. Ngati mukufuna kugwiritsa ntchito mabatire oyimilira, ayenera kukhala acid acid kapena gel osakaniza. Lumikizani batire ku ma terminals olembedwa [- BAT +] (Mkuyu 4g, pg. 6). Gwiritsani ntchito mabatire awiri (2) 12VDC olumikizidwa mndandanda wa 24VDC opareshoni (mabatire amatsogolera akuphatikizidwa). Gwiritsani ntchito mabatire - Casil CL1270 (12V/7AH), CL12120 (12V/12AH), CL12400 (12V/40AH), CL12650 (12V/65AH) mabatire kapena UL ozindikiridwa BAZR2 ndi BAZR8 mabatire oyenerera.
12. Zotuluka mu Battery ndi AC Supervision (mkuyu 4, tsamba 8):
    Lumikizani zida zozindikiritsa zoyankhulirana ndi matheminali olembedwa [AC FAIL & BAT FAIL] (Mku. 4b, pg. 5) zotulukapo zopatsirana zoyang'anira. Gwiritsani ntchito 22 AWG mpaka 18 AWG pa AC Fail & Low/No Battery lipoti.
13. Kuti muchedwe kupereka lipoti kwa maola 6., dulani "AC Kuchedwa" jumper ndi kubwezeretsa mphamvu ku unit (mkuyu 4f, pg. 6).
14. Kuyimitsa Alamu ya Moto (mkuyu 4c, tsamba 6):
    • Kuti mutsegule Alamu ya Moto Disconnect ikani kusintha kwa DIP [Kuzimitsa] kukhala ON malo.
    • Kuti muyimitse Alamu ya Moto Chotsani chotsani chosinthira cha DIP [Chotseka] kuti CHOZIMITSA.
15. Kuyika kwa tampkusintha kwa:
    Mount UL Listed tamper switch (Altronix model TS112 kapena yofanana) pamwamba pa mpanda. Tsegulani tamper switch bracket m'mphepete mwa mpanda pafupifupi 2" kuchokera kumanja (mkuyu 6a, p. 8). Gwirizanitsani tampsinthani mawaya kupita ku Access Control Panel kapena chida choyenera cha UL Listed reporting. Kuti mutsegule chizindikiro cha alamu, tsegulani chitseko cha mpanda.

Kusamalira

Gawo liyenera kuyesedwa kamodzi pachaka kuti ligwire bwino ntchito motere:

• Kutulutsa Voltage Mayeso: Pansi pa katundu wabwinobwino mphamvu ya DC yotulutsa voltage iyenera kufufuzidwa ngati voliyumu yoyeneratagmulingo e.
• Kuyesa kwa Battery: Pazikhalidwe zolemedwa bwino, fufuzani kuti batire yadzaza, fufuzani voltage potengera mabatire komanso pamalo opangira ma board omwe amalembedwa [- BAT +] kuwonetsetsa kuti palibe kusweka kwa mawaya olumikizira batire.

Zindikirani: Kuchulukirachulukira kwapano pakutulutsa ndi 3.6A.
Zindikirani: Moyo wa batri woyembekezeka ndi zaka 5; komabe, tikulimbikitsidwa kusintha mabatire muzaka 4 kapena kuchepera ngati pakufunika

Chithunzi cha 4-AL1024ULXB2 Kukonzekera kwa Board

 

LED Diagnostics

AL1024ULXB2 - Bungwe Lopereka Mphamvu 

Chofiira (DC)	Zobiriwira (AC)	Mkhalidwe Wopereka Mphamvu
ON	ON	Mkhalidwe wabwinobwino wogwirira ntchito.
ON	ZIZIMA	Kutaya kwa AC. Batire yoyimilira ikupereka mphamvu.
ZIZIMA	ON	Palibe zotulutsa za DC.
ZIZIMA	ZIZIMA	Kutaya kwa AC. Batiri lotulutsidwa kapena lopanda kuyimilira. Palibe zotulutsa za DC.

ACMS8 ndi ACMS8CB Access Power Controller 

LED	ON	ZIZIMA
LED 1- LED 8 (Yofiira)	Kutulutsa kotulutsa mphamvu kopanda mphamvu.	zotulutsa zopatsa mphamvu.
FACP	Kulowetsa kwa FACP kuyambika (ma alarm).	FACP yachibadwa (yopanda ma alarm).
Zobiriwira Zobiriwira 1-8	12VDC	–
Kutulutsa Kofiira 1-8	24VDC	–

Chizindikiritso cha Terminal

AL1024ULXB2 - Bungwe Lopereka Mphamvu 

Mbiri ya Terminal	Ntchito/Kufotokozera
L, N	Lumikizani 115VAC ku ma terminals awa: L mpaka kutentha, N kuti asalowerere (Chith. 4a, pg. 6).
+ DC -	Fakitale yolumikizidwa ndi ACMS8(CB) (Chith. 4d, pg. 6).
AC Fail NC, C, NO	Amagwiritsidwa ntchito podziwitsa kutayika kwa mphamvu ya AC, mwachitsanzo kulumikiza ku chipangizo chomveka kapena gulu la alamu. Relay nthawi zambiri imakhala ndi mphamvu ngati mphamvu ya AC ilipo. Contact mlingo 1A @ 28VDC. Kulephera kwa AC kapena brownout kumanenedwa mkati mwa mphindi imodzi ya chochitika. Kuti muchedwe kupereka lipoti mpaka ma 6 hrs., dulani "AC Delay" jumper ndikukhazikitsanso mphamvu ku unit. (Chith. 4f, pg. 6).
Bat Fail NC, C, NO	Amagwiritsidwa ntchito kusonyeza kutsika kwa batire, mwachitsanzo kulumikiza ku alamu. Relay nthawi zambiri imakhala ndi mphamvu ngati mphamvu ya DC ilipo. Contact mlingo 1A @ 28VDC. Batire yochotsedwa imanenedwa mkati mwa mphindi imodzi. Kulumikizananso kwa batri kumadziwika mkati mwa mphindi imodzi. Batire yotsika: pafupifupi 21VDC (Mku. 4b, tsamba 6).
- BAT +	Kulumikizana kwa batire yoyimilira. Malipiro apamwamba kwambiri 3.6A (Chith. 4c, pg. 6).

ACMS8 ndi ACMS8CB Access Power Controller 

Mbiri ya Terminal	Ntchito/Kufotokozera
+ PWR1 -	Zogwirizana ndi AL1024ULXB2. Osagwiritsa ntchito ma terminals awa.
+ PWR2 -	Fakitale yolumikizidwa ndi VR6 voltagndi regulator. Osagwiritsa ntchito ma terminals awa.
+ INP1 - kudzera + INP8 -	Zisanu ndi zitatu (8) zodziyimira pawokha Zotsegula Pazonse (NO), Zomwe Zimatsekedwa (NC), Open Collector Sink kapena Wet Input Triggers.
C, NC	FACP Dry NC yotulutsa idavotera 1A/28VDC @ 0.6 Power Factor. Class 2 alibe mphamvu. Ndi EOL JMP yosasunthika, ipereka kukana kwa 10k pamalo abwino.
GND, RST	FACP mawonekedwe latching kapena osawotchera. PALIBE mawu owuma. Class 2 alibe mphamvu. Kufupikitsidwa kwa mawonekedwe osagwirizana ndi FACP kapena kukhazikitsanso Latch FACP.
GND, EOL	EOL Supervised FACP Input terminals for polarity reversal FACP function. Class 2 alibe mphamvu.
- F, + F, - R, + R	FACP Signaling Circuit Inpuit and Return terminals. Class 2 alibe mphamvu.
Kutulutsa 1 kudutsa Zotsatira 8 NO, C, NC, COM	Zotuluka zisanu ndi zitatu (8) zosankhidwa paokha [Fail-Safe (NC) kapena Fail-Secure (NO)] ndi zisanu ndi zitatu (8) zowongolera pawokha za "C" Relay.

Chithunzi cha 6-AL1024NKA8(D)

CHENJEZO: Gwiritsani ntchito mabatire awiri (2) 12VDC oyimilira.

• Sungani mawaya opanda mphamvu osiyana ndi opanda mphamvu. Gwiritsani ntchito matayala osachepera 0.25 ″.
• 12AH Mabatire omwe amatha kuchangidwanso ndi mabatire akulu kwambiri omwe amatha kulowa mchipindachi.
• Batire yakunja yolembedwa ndi UL iyenera kugwiritsidwa ntchito ngati mukugwiritsa ntchito mabatire a 40AH kapena 65AH.

Chithunzi Choyimira Ntchito

Zithunzi za Hook-Up

• Chithunzi cha 8 - Daisy-chaining imodzi kapena zingapo za ACMS8 (CB). EOL Jumper [EOL JMP] iyenera kukhazikitsidwa pamalo a EOL. Osa Latching.
  
• Chithunzi cha 9 - Daisy-chaining imodzi kapena zingapo za ACMS8 (CB). EOL Jumper [EOL JMP] iyenera kukhazikitsidwa pamalo a EOL. Kuyanjanitsa Single Reset.
  
• Chithunzi 10 - Daisy akumanga mayunitsi amodzi kapena angapo a ACMS8(CB). EOL Jumper [EOL JMP] iyenera kukhazikitsidwa pamalo a EOL. Latching Individual Reset.
  

Zithunzi za Hook-Up

• Chithunzi 11 - Polarity reversal input kuchokera ku FACP signing circuit output (polarity imatchulidwa mu alarm condition). Osa Latching
  
• Chithunzi 12 - Polarity reversal input kuchokera ku FACP signing circuit output (polarity imatchulidwa mu chikhalidwe cha alarm). Latching
  
• Chithunzi 13 - Nthawi zambiri Kutsekedwa koyambitsa kulowetsa (Non-Latching).
  
• Chithunzi 14 - Nthawi zambiri Kutsekedwa koyambitsa kulowetsa (Latching).
  
• Chithunzi 15 - Nthawi zambiri Open trigger input (Non-Latching)
  
• Chithunzi 16 - Nthawi zambiri Open trigger input (Latching).
  

Miyeso Yampanda (BC400)

15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm)

Altronix siwoyambitsa zolakwika zilizonse za typographical. 140 58th Street, Brooklyn, New York 11220 USA

• foni: 718-567-8181
• fax: 718-567-9056
• webtsamba: www.kalit.com
• imelo: info@altronix.com
• Chitsimikizo cha moyo wonse

Zolemba / Zothandizira

Altronix AL1024NKA8 Series Dual Output Access Power Controllers [pdf] Kukhazikitsa Guide AL1024NKA8, AL1024NKA8D, AL1024NKA8 Series Zowongolera Mphamvu Zapawiri Zotulutsa Mphamvu, Zowongolera Mphamvu Zapawiri, Zowongolera Mphamvu Zofikira, Zowongolera Mphamvu Zapawiri, Zowongolera Mphamvu

Maumboni

• Buku Logwiritsa Ntchito