Abubuwan da ke ciki
boye
Altronix AL1024NKA8 Series Dual Output Access Power Controllers
Ƙarsheview
Altronix AL1024NKA8 da AL1024NKA8D suna rarrabawa da canza wuta don samun damar tsarin sarrafawa da kayan haɗi. Suna juyar da shigarwar 115VAC 60Hz zuwa takwas (8) sarrafa kayan sarrafawa na 12VDC ko 24VDC masu zaman kansu. Zane-zanen shigarwa biyu na Mai Gudanar da Wutar Wuta yana ba da damar sarrafa wutar lantarki daga masana'anta guda biyu (2) da aka girka masu zaman kansu masu zaman kansu.tage 12 ko 24VDC Altronix samar da wutar lantarki zuwa takwas (8) fiusi mai sarrafa kansa (AL1024NKA8) ko PTC (AL1024NKA8D) abubuwan kariya. Za'a iya canza abubuwan da aka fitar da wutar lantarki zuwa busassun lambobi "C". Ana kunna fitarwa ta hanyar buɗaɗɗen mai tattarawa, yawanci buɗewa (NO), yawanci rufe (NC) shigar da busasshen faɗakarwa, ko rigar fitarwa daga Tsarin Kulawa, Mai karanta Kati, faifan maɓalli, Maɓallin turawa, PIR, da sauransu. AL1024NKA8(D) zai ikon hanya zuwa nau'ikan na'urorin sarrafa kayan aiki iri-iri ciki har da Makullin Mag, Harshen Wutar Lantarki, Masu riƙe da Ƙofa na Magnetic, da dai sauransu. Abubuwan da aka fitar za su yi aiki a cikin yanayin rashin aminci da/ko rashin aminci. Fuskar FACP tana ba da damar Ƙaddamar Gaggawa, Kula da Ƙararrawa, ko ƙila a yi amfani da su don haifar da wasu na'urori masu taimako. Siffar cire haɗin ƙararrawar wuta ana iya zaɓa ɗaya ɗaya don kowane ko duka na takwas (8). Masu haɗin spade suna ba ku damar ikon sarkar daisy zuwa maɗaukakin ACMS8(CB). Wannan fasalin yana ba ku damar rarraba wutar lantarki akan ƙarin abubuwan fitarwa don manyan tsarin.
Ƙayyadaddun Tsayayye (jimlar halin yanzu da aka nuna)
| Fitowa | 15 min. na Tsayawa da 5 min. na Ƙararrawa | 4h ku. na Tsayawa da 5 min. na Ƙararrawa | 24h ku. na Tsayawa
kuma 5 min. na Ƙararrawa |
60h ku. na Tsayawa
kuma 5 min. na Ƙararrawa |
| 24VDC/12AH
Baturi |
Tsayawa = 8A Ƙararrawa = 10A | Tsayawa = 1.5A Ƙararrawa = 10A | Tsayawa = 200mA Ƙararrawa = 10A | Tsayawa = 100mA Ƙararrawa = 10A |
| Fitowa | 15 min. na Tsayawa da 5 min. na Ƙararrawa | 4h ku. na Tsayawa da 5 min. na Ƙararrawa | 24h ku. na Tsayawa da 15 min. na Ƙararrawa | 60h ku. na Tsayawa da 15 min. na Ƙararrawa |
| 24VDC/65AH
Baturi |
– | Tsayawa = 8.0A Ƙararrawa = 10A | Tsayawa = 1.5A Ƙararrawa = 10A | Tsayawa = 500mA Ƙararrawa = 10A |
Don aikace-aikacen Ikon Samun damar, ƙarfin baturi don wadatar 10A na yanzu - 1 hr. don baturi 24VDC/12AH, 6.5 hours. don baturi 24VDC/65AH. Dubi takardar lissafin girman baturi a ƙasa don wasu batura.
- A. AL1024NKA8(D) amfani na ciki na yanzu (tsayawa) ________________ 0.05 A
- B. Load da amfani na yanzu (tsayawa) ________________ A
- C. Lokacin jiran aiki da ake buƙata (awanni) ________________ H
- D. Ana buƙatar ƙarfin baturi don jiran aiki (A+B)*C ________________ AH
- E. AL1024NKA8(D) yawan wutar lantarki na ciki (Ƙararrawa) ________________ 0.05 A
- F. Load da amfani na yanzu (Ƙararrawa) ________________ A
- G. Tsawon ƙararrawa (Sa'o'i; Minti 15 = Sa'a 0.25) (Ƙararrawa) ________________ H
- H. Ana buƙatar ƙarfin baturi don Ƙararrawa (E+F)*G ________________ AH
- I. Jimlar ƙarfin baturi D+H ________________ AH
- J. Ana buƙatar ƙarfin baturi I*1.8 (fasali na aminci) ________________ AH
Lura: AL1024NKA8(D) samar da wutar lantarki an tsara shi don aiki tare da batura har zuwa 65AH. Lura: layin [I] kada ya wuce 36AH.
Dole ne ku rage ko dai jiran aiki na yanzu ko lokacin jiran aiki don biyan buƙatu. Don tantance ainihin girman baturi da fatan za a zagaye layi [J] zuwa mafi girman daidaitaccen girman baturi mafi kusa (misali 3.5 AH = 4.0 AH).
Ƙayyadaddun bayanai
Abubuwan shigarwa:
- AL1024ULXB2
- 115VAC, 60Hz, 4.2A.
- ACMS8/ACMS8CB:
- Abubuwan shigar da abubuwa takwas (8)
- a) Yawan buɗewa (NO) abubuwan shigar (buƙaƙen lambobi).
- b) Abubuwan shigarwar da aka saba rufe (NC) (buƙaƙen lambobi).
- c) Bude abubuwan shigar da mai tarawa.
- d) Wet Input (5VDC - 24VDC) tare da 10K resistor
- e) Duk wani hade na sama.
- Abubuwan shigar da abubuwa takwas (8)
Abubuwan da aka fitar:
- Ƙarfi:
- 12VDC ko 5VDC har zuwa 6A, 24VDC har zuwa 10A (240W jimlar iko).
- Ƙarfafawatage kariya.
- ACMS8:
- Abubuwan da aka kare-fuse mai ƙididdigewa @ 2.5A ga kowane fitarwa, mara iyaka. Jimlar fitarwa 6A max. Kada ku wuce daidaitattun ƙimar samar da wutar lantarki.
- ACMS8CB:
- Abubuwan da ke da kariya na PTC wanda aka ƙididdige @ 2A akan kowace fitarwa, Class 2-iyakantacce. Jimlar fitarwa 6A max. Kada ku wuce daidaitattun ƙimar samar da wutar lantarki.
- Takwas (8) zaɓaɓɓun abubuwan sarrafawa masu zaman kansu ko takwas (8) abubuwan da aka sarrafa na Form "C" waɗanda ba a sarrafa su ba (duba ƙasa don ƙididdigewa):
- a) Rashin-Lafiya da/ko Ƙarfin-Tsarin abubuwan samar da wutar lantarki.
- b) Form "C" relays mai ƙididdigewa @ 2.5A. 12, 24VDC, 0.6 Power Factor (ACMS8 kawai).
- c) Abubuwan wutar lantarki na taimako (ba a kunna ba).
- d) Duk wani hade na sama.
- Za'a iya saita abubuwan da aka fitar guda ɗaya zuwa matsayin KASHE don yin hidima (saitin jumper zuwa matsayi na tsakiya). Ba ya aiki ga busasshiyar tuntuɓar aikace-aikacen.
- Ana iya zaɓar kowane ɗayan fiusi takwas (8) fuse/PTC da aka kariyar wutar lantarki don bin shigar da wutar lantarki 1 ko Input 2. Output vol.tage na kowane fitarwa iri ɗaya ne da shigar voltage na shigar da aka zaɓa.
- Damuwawar tiyata.
Ƙimar Fuse/PTC:
- AL1024ULXB2
- An ƙididdige fis ɗin shigarwa 5A/250V.
- Fuskar baturi 15A/32V.
- ACMS8:
- Babban shigar da fiusi an ƙididdige 15A/32V.
- Ana ƙididdige fis ɗin fitarwa 3A/32V.
- ACMS8CB:
- Babban shigarwar PTC an kimanta 9A.
- Ana ƙididdige fitowar PTC 2A.
Ajiyayyen Baturi:
- Caja da aka gina a ciki don rufaffiyar gubar acid ko nau'in batura na gel.
- Canja atomatik zuwa baturin jiran aiki lokacin da AC ta gaza.
- Matsakaicin caji na yanzu 3.6A.
- Zero voltage sauke lokacin da aka canza zuwa madadin baturi.
Kulawa:
- AC gaza kulawa (form "C" lambobin sadarwa).
- Ƙananan kula da baturi (format "C" lambobin sadarwa).
- Kula da kasancewar baturi (form "C" lambobin sadarwa).
Kashe Haɗin Ƙararrawar Wuta:
- Cire haɗin ƙararrawa na Wuta (latching ko rashin latching) ana iya zaɓin ɗaiɗaiku don kowane ko duka na takwas (8). Zaɓuɓɓukan shigar da ƙararrawar wuta:
- a) Akan buɗe [NO] ko kuma rufe [NC] busasshen shigar da lamba. Shigar da juyar da polarity daga da'irar siginar FACP.
- An ƙididdige shigarwar FACP WET 5-30VDC 7mA.
- Shigar da FACP EOL yana buƙatar 10K ƙarshen resistor layi.
- FACP fitarwa relay [NC]:
Ko dai Dry 1A/28VDC, 0.6 Power Factor ko 10K juriya tare da [EOL JMP] cikakke.
Alamun gani:
- AL1024ULXB2
- Green AC LED: Yana nuna 115VAC yanzu.
- Red DC LED: Yana nuna fitowar DC.
- ACMS8 (CB):
- Red LEDs: Nuna abubuwan da aka kunna.
- Blue LED: Yana nuna cire haɗin FACP yana jawo.
- Mutum Voltage LEDs: Nuna 12VDC (Green) ko 24VDC (Ja).
Muhalli:
- Yanayin aiki: 0ºC zuwa 49ºC na yanayi.
- Humidity: 20 zuwa 85%, mara taurin kai.
Girman Rukunin (kimanin H x W x D): 15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm).
Umarnin Shigarwa
Hanyoyin wayoyi za su kasance daidai da Lambar Wutar Lantarki ta Ƙasa/NFPA 70/NFPA 72/ANSI, Lambar Lantarki ta Kanada kuma tare da duk lambobin gida da hukumomi masu iko. An yi nufin samfurin don amfanin cikin gida kawai.
- Dutsen naúrar a wurin da ake so. Yi alama da ramuka a bango don yin layi tare da manyan maɓallan maɓalli guda biyu a cikin shingen. Shigar da manyan haɗe-haɗe biyu da sukurori a bango tare da ɗumbin kawunan suna fitowa. Sanya manyan rijiyoyin maɓalli na sama sama biyu na sama, matakin kuma amintattu. Alama matsayi na ƙananan ramuka biyu. Cire shingen. Hana ƙananan ramuka kuma shigar da masu ɗaure biyu. Sanya ramukan maɓalli na sama sama biyu na sama. Shigar da ƙananan sukurori biyu kuma tabbatar da ƙarfafa duk screws (Ƙararren Ƙararren, shafi 12). Amintaccen shinge ga ƙasan ƙasa.
- Tabbatar da duk masu tsalle-tsalle masu fitarwa [PWR1] - [PWR8] an sanya su a cikin KASHE (tsakiya) matsayi (Fig. 1, shafi 3).
- Haɗa ƙarfin AC mara kunnawa (115VAC 60Hz) zuwa tashoshi masu alama [L, N] (Hoto 4a, shafi 5). Green “AC” LED akan allon samar da wutar lantarki zai kunna. Ana iya ganin wannan hasken ta hanyar ruwan tabarau na LED da ke kofar shingen. Yi amfani da 14 AWG ko mafi girma don duk haɗin wutar lantarki. Amintaccen koren waya yana kaiwa zuwa ƙasa. Ajiye wayoyi masu iyaka dabam dabam daga wayoyi marasa iyaka (Input 115VAC 60Hz, Wayoyin Baturi). Dole ne a samar da tazara mafi ƙarancin 0.25.
HANKALI: Kar a taɓa sassan ƙarfe da aka fallasa. Kashe wutar da'irar reshe kafin shigarwa ko kayan aiki. Babu sassa masu amfani a ciki. Koma shigarwa da hidima ga ƙwararrun ma'aikatan sabis. - Saita kowane fitarwa [OUT1] - [OUT8] zuwa hanyar wutar lantarki daga Shigarwar 1 ko 2 (Fig. 1, shafi 3).
Lura: Auna fitarwa voltage kafin haɗa na'urori. Wannan yana taimakawa guje wa lalacewa mai yuwuwa. - Kashe wuta kafin haɗa na'urori.
- Zaɓuɓɓukan fitarwa: AL1024NKA8(D) zai samar da wutar lantarki har takwas (8) da aka canza ko kuma takwas (8) busassun nau'i na "C", ko duk wani haɗin da aka canza da kuma samar da "C", da takwas (8) ba a kunna ba. karin ƙarfin lantarki.
- Abubuwan da aka Canja Wuta:
Haɗa madaidaicin shigarwar (-) na na'urar da ake kunna wuta zuwa tasha mai alama [COM].- Don Rashin-Safe aiki haɗa ingantaccen shigarwar (+) na na'urar da ake kunna wuta zuwa tashar da aka yiwa alama [NC].
- Don Ƙarfafa Amintaccen aiki haɗa ingantaccen shigarwar (+) na na'urar da ake kunna wutar lantarki zuwa tasha mai alama [NO].
- Form "C" abubuwan da aka fitar:
Lokacin da ake son fitar da nau'in "C", dole ne a sanya madaidaicin jumper (1-8) a cikin KASHE (Fig. 7, shafi 9). A madadin, ana iya cire fis ɗin fitarwa mai dacewa (1-8) (AL1024NKA8 kawai). Haɗa korau (-) na wutar lantarki kai tsaye zuwa na'urar kullewa. Haɗa tabbataccen (+) na wutar lantarki zuwa tasha mai alama [C].- Don Rashin-Safe aiki haɗa tabbataccen (+) na na'urar da aka kunna zuwa tashar da aka yiwa alama [NC].
- Don Ƙarfafa Amintaccen aiki haɗa tabbataccen (+) na na'urar da aka kunna zuwa tashar da aka yiwa alama [NO]. Busassun adireshi masu ƙima @ 2.5A, 28VDC.
- Fitowar wutar lantarki (ba a kunna):
Haɗa ingantaccen shigarwar (+) na na'urar da ake kunna wuta zuwa tashar da aka yiwa alama [C] da kuma mummunan (-) na na'urar da ake kunna wutar zuwa tasha mai alama [COM]. Ana iya amfani da fitarwa don samar da wuta ga masu karanta katin, maɓalli da sauransu.
- Abubuwan da aka Canja Wuta:
- Kunna babban wuta bayan an haɗa duk na'urori.
- Zaɓuɓɓukan Ƙarfafa shigarwa:
Lura: Idan ba a yi amfani da cire haɗin Ƙararrawar Wuta ba, haɗa 10K ohm resistor zuwa tashoshi masu alama [GND da EOL], da haɗa jumper zuwa tashoshi masu alama [GND, RST].
Shigarwa Akan Buɗe (NO):
Slide shigar da dabaru na Slide DIP canzawa zuwa cikin KASHE matsayi don [Canja 1-8] (Fig. 2, a dama). Haɗa wayoyi zuwa tashoshi masu alamar [+ INP1 -] zuwa [+ INP8 -].
Shigarwar Akan Rufe (NC):
Slide shigar da dabaru na Slide DIP canzawa zuwa cikin ON matsayi na [Cuyawa 1-8] (Fig. 2, a dama). Haɗa wayoyi zuwa tashoshi masu alamar [+ INP1 -] zuwa [+ INP8 -].
Buɗe Shigar Mai Tari:
Haɗa shigar da buɗaɗɗen shigarwar nutsewar mai tarawa zuwa tashar da aka yiwa alama [+ INP1 -] zuwa [+ INP8 -].
Jika (Voltage) Kanfigareshan shigarwa:
A hankali lura da polarity, haɗa voltage shigar da wayoyi masu jawowa da kuma samar da resistor 10K zuwa tashoshi masu alamar [+ INP1 -] zuwa [+ INP8 -].
Idan ana amfani da voltage don kunna shigarwa - saita madaidaicin INP Logic sauyawa zuwa matsayin "KASHE".
Idan cire voltage don kunna shigarwa - saita madaidaicin INP Logic sauyawa zuwa matsayi "ON". - Zaɓuɓɓukan Interface Ƙararrawa:
Rufe [NC], yawanci buɗe [NO] shigarwar ko shigar da juzu'i na polarity daga da'irar siginar FACP zai haifar da zaɓin abubuwan da aka zaɓa. Don kunna cire haɗin FACP don fitarwa kunna maɓallin DIP daidai [SW1-SW8] ON. Don musaki cire haɗin FACP don fitarwa kunna maɓallin DIP daidai [SW1-SW8] KASHE. Canjawa yana tsaye kai tsaye zuwa hagu na Tashoshin Matsalolin Ƙararrawar Wuta.
Yawan Buɗe Shigarwa:
Waya gudun ba da sanda na FACP ɗin ku da resistor 10K a layi daya akan tashoshi masu alamar [GND] da [EOL].
Shigarwa Akan Rufe:
Wire relay na FACP ɗin ku da resistor 10K a jere akan tashoshi masu alamar [GND] da [EOL].
FACP Siginar Ƙarfafa Shigar da Wuta:
Haɗa tabbataccen (+) da korau (-) daga fitowar sigina na FACP zuwa tashoshi masu alama [+ FACP -]. Haɗa FACP EOL zuwa tashoshi masu alamar [+ RET -] (an yi la'akari da polarity a cikin yanayin ƙararrawa).
Kashe Haɗin Ƙararrawar Wuta mara Latsawa: Haɗa jumper zuwa tashoshi masu alama [GND, RST]. - FACP Dry NC fitarwa:
Haɗa na'urar da ake so don buɗewa ta busasshiyar fitowar lamba ta naúrar zuwa tashoshi masu alama [NC] da [C]. Lokacin da aka kiyaye [EOL JMP], abin da ake fitarwa shine juriya na 0 Ohm a cikin yanayin al'ada. Lokacin da aka yanke [EOL JMP], juriya 10k za a wuce zuwa na'ura ta gaba lokacin da ke cikin yanayin al'ada. - Haɗin Batir na tsaye (Hoto 6, shafi 8):
Don aikace-aikacen Ikon Samun damar Amurka batura na zaɓi ne. Ana buƙatar batura don shigarwa na Kanada (ULC-S319). Lokacin da ba a yi amfani da batura ba, asarar AC zai haifar da asarar juzu'in fitarwatage. Lokacin da ake son amfani da batura masu aiki, dole ne su zama nau'in gubar acid ko gel. Haɗa baturi zuwa tashoshi masu alama [- BAT +] (Fig. 4g, shafi 6). Yi amfani da batura guda biyu (2) 12VDC da aka haɗa a jeri don aikin 24VDC (an haɗa da jagororin baturi). Yi amfani da batura - Casil CL1270 (12V / 7AH), CL12120 (12V / 12AH), CL12400 (12V / 40AH), CL12650 (12V / 65AH) batir ko UL gane batir BAZR2 da BAZR8 na ƙimar da ta dace. - Abubuwan Baturi da Kulawar AC (Hoto 4, shafi 8):
Haɗa na'urorin sanarwar siginar da suka dace zuwa tashoshi masu alamar [AC FAIL & BAT FAIL] (Hoto 4b, shafi 5) fitattun abubuwan sa ido. Yi amfani da 22 AWG zuwa 18 AWG don gazawar AC & Ƙananan / Babu rahoton baturi. - Don jinkirta bayar da rahoto har zuwa sa'o'i 6., yanke tsalle "AC Delay" kuma sake saita wutar lantarki zuwa naúrar (Fig. 4f, shafi 6).
- Cire Haɗin Ƙararrawar Wuta (Hoto 4c, shafi 6):
- Don kunna Cire Haɗin Ƙararrawar Wuta saita sauya DIP [Rufewa] zuwa Matsayin ON.
- Don kashe Ƙararrawar Wuta Cire haɗin yanar gizo saita sauya DIP [Rufewa] zuwa KASHE matsayi.
- Shigar da tampya canza:
Dutsen UL Jerin tamper canza (samfurin Altronix TS112 ko daidai) a saman shingen. Zamar da tampmadaidaicin madaidaicin maɓalli a gefen shingen kusan 2” daga gefen dama (Fig. 6a, shafi 8). Haɗa tampcanza wayoyi zuwa shigar da Panel Control Panel ko na'urar da aka jera UL mai dacewa. Don kunna siginar ƙararrawa buɗe ƙofar kewayen.
Kulawa
Ya kamata a gwada naúrar aƙalla sau ɗaya a shekara don aikin da ya dace kamar haka:
- Fitarwa Voltage Gwaji: A ƙarƙashin yanayin kaya na yau da kullun, fitarwar DC voltage ya kamata a duba don daidai voltage darajar.
- Gwajin Baturi: A ƙarƙashin yanayin kaya na al'ada duba cewa an cika cajin baturin, duba ƙayyadaddun voltage duka a tashar baturi da kuma tashoshin allon allon da aka yiwa alama [- BAT +] don tabbatar da cewa babu karya a cikin wayoyi masu haɗin baturi.
Lura: Matsakaicin caji na yanzu ƙarƙashin fitarwa shine 3.6A.
Lura: Rayuwar baturi da ake tsammani shine shekaru 5; duk da haka, ana ba da shawarar canza batura a cikin shekaru 4 ko ƙasa da haka idan an buƙata
Hoto 4 - AL1024ULXB2 Kanfigareshan Jirgin
LED Diagnostics
AL1024ULXB2 - Hukumar Samar da Wutar Lantarki
| Ja (DC) | Green (AC) | Matsayin Samar da Wuta |
| ON | ON | Yanayin aiki na al'ada. |
| ON | KASHE | Asarar AC. Baturi na tsaye yana samar da wuta. |
| KASHE | ON | Babu fitarwa na DC. |
| KASHE | KASHE | Asarar AC. An cire ko babu baturi mai jiran aiki. Babu fitarwa na DC. |
ACMS8 da ACMS8CB Mai Kula da Wutar Lantarki
| LED | ON | KASHE |
| LED 1-LED 8 (ja) | Relay(s) na fitar da kuzari. | Relay(s) na fitar da kuzari. |
| Farashin FACP | An kunna shigar da FACP (yanayin ƙararrawa). | FACP na al'ada (yanayin rashin ƙararrawa). |
| Koren Fitowa 1-8 | Saukewa: 12VDC | – |
| Jajayen Fitowa 1-8 | Saukewa: 24VDC | – |
Ganewar Tasha
AL1024ULXB2 - Hukumar Samar da Wutar Lantarki
| Labarin Ƙarshe | Aiki/Bayyana |
| L, N | Haɗa 115VAC zuwa waɗannan tashoshi: L zuwa zafi, N zuwa tsaka tsaki (Fig. 4 a, ku. pg. 6). |
| + DC - | Kamfanin da aka haɗa zuwa ACMS8(CB) (Fig. 4d, pg. 6). |
|
AC Fail NC, C, NO |
Ana amfani da shi don sanar da asarar wutar AC, misali haɗa zuwa na'ura mai ji ko ƙararrawa. Relay yawanci ana samun kuzari lokacin da wutar AC ta kasance. Ƙimar lamba 1A @ 28VDC. Ana ba da rahoton gazawar AC ko launin ruwan kasa a cikin minti 1 na aukuwa.
Don jinkirta bayar da rahoto har zuwa sa'o'i 6., yanke "AC Delay" jumper kuma sake saita wutar lantarki zuwa naúrar. (Fig. 4 f, pg. 6). |
| Bat Fail NC, C, NO | Ana amfani da shi don nuna ƙarancin yanayin baturi, misali haɗi zuwa sashin ƙararrawa.
Relay yawanci yana samun kuzari lokacin da ƙarfin DC ya kasance. Ƙimar lamba 1A @ 28VDC. An ba da rahoton cire baturi a cikin minti 1. An bayar da rahoton sake haɗa baturi a cikin minti 1. Ƙananan iyakar baturi: kusan 21VDC (Hoto na 4b, shafi na 6). |
| - BAT + | Haɗin baturi na tsaye. Matsakaicin caji na yanzu 3.6A (Fig. 4c ku, pg. 6). |
ACMS8 da ACMS8CB Mai Kula da Wutar Lantarki
| Labarin Ƙarshe | Aiki/Bayyana |
| PWR1- | Factory da aka haɗa zuwa AL1024ULXB2. Kar a yi amfani da waɗannan tashoshi. |
| PWR2- | Kamfanin da aka haɗa zuwa VR6 voltage regulator. Kar a yi amfani da waɗannan tashoshi. |
| + INP1 - ta hanyar
+ INP8- |
Takwas (8) mai zaman kansa Buɗewa ta al'ada (NO), An rufe ta ta al'ada (NC), Buɗaɗɗen Mai Tari ko Rigar shigar da Jika. |
| C, NC | FACP Dry NC fitarwa mai ƙima 1A/28VDC @ 0.6 Factor Power. Matsayi na 2 mai iyaka. Tare da EOL JMP cikakke, zai samar da juriya na 10k a cikin yanayin al'ada. |
| GND, RST | FACP interface latching ko rashin latching. NO bushe shigarwa. Matsayi na 2 mai iyaka. Don a gajarta don ƙirar FACP mara amfani ko Latch FACP sake saiti. |
| GND, EOL | EOL Tashoshin shigarwar FACP mai kulawa don juyar da aikin FACP na polarity. Matsayi na 2 mai iyaka. |
| - F, + F, - R, + R | Shigar da siginar siginar FACP da tasha. Matsayi na 2 mai iyaka. |
| Fitowa ta 1
Fitarwa 8 NO, C, NC, COM |
Takwas (8) zaɓaɓɓun abubuwan sarrafawa masu zaman kansu [Fail-Safe (NC) ko Fail-Secure (NO)] da takwas (8) abubuwan sarrafawa na Form “C” masu zaman kansu. |
Hoto 6 - AL1024NKA8(D)
HANKALI: Yi amfani da baturan jiran aiki guda biyu (2) 12VDC.
- Kiyaye iyakataccen wayoyi daban da mara iyaka. Yi amfani da mafi ƙarancin tazarar 0.25 inci.
- 12AH batura masu caji sune manyan batura waɗanda zasu iya dacewa da wannan shingen.
- Dole ne a yi amfani da shingen baturi na waje mai jera UL idan ana amfani da batura 40AH ko 65AH.
Tsarin aikace-aikace na yau da kullun
Hoto-Up
- Hoto 8 – Daisy- sarkar daya ko fiye ACMS8(CB) raka'a. Ya kamata a shigar da EOL Jumper [EOL JMP] a matsayin EOL. Rashin Latsawa.
- Hoto 9 – Daisy- sarkar daya ko fiye ACMS8(CB) raka'a. Ya kamata a shigar da EOL Jumper [EOL JMP] a matsayin EOL. Latching Single Sake saiti.
- Hoto 10 – Daisy sarkar daya ko fiye ACMS8(CB) raka'a. Ya kamata a shigar da EOL Jumper [EOL JMP] a matsayin EOL. Latching Mutum Sake saitin.
Hoto-Up
- Hoto 11 – Shigar da juyar da polarity daga fitowar sigina ta FACP (an yi la'akari da polarity a yanayin ƙararrawa). Rashin Latsawa
- Hoto 12 – Shigar da jujjuyawar polarity daga fitowar sigina na FACP (an yi nuni da polarity a yanayin ƙararrawa). Latching
- Hoto na 13 – Abubuwan shigar da faɗakarwa da aka rufe (Ba Latching).
- Hoto na 14 – Rufe shigarwar faɗakarwa (Latching).
- Hoto 15 – Buɗe shigarwar faɗakarwa ta al'ada (Ba Latching)
- Hoto 16 – Buɗe shigar da faɗakarwa ta al'ada (Latching).
Girman Rukunin (BC400)
15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm)
Altronix bashi da alhakin kowane kurakurai na rubutu. 140 58th Street, Brooklyn, New York 11220 Amurka
- waya: 718-567-8181
- fakis: 718-567-9056
- website: www.altronix.com
- e-mail: info@altronix.com
- Garanti na rayuwa
Takardu / Albarkatu
 |
Altronix AL1024NKA8 Series Dual Output Access Power Controllers [pdf] Jagoran Shigarwa AL1024NKA8, AL1024NKA8D, AL1024NKA8 Series Dual Output Access Power Controllers, Dual Output Access Power Controllers, Access Power Controllers, Dual Output Power Controllers, Power Controllers |
