Altronix AL1024NKA8 Series Dual Output Access Power Controllers Installation Guide

Altronix AL1024NKA8 uye AL1024NKA8D kugovera uye kushandura simba kuti uwane kudzora masisitimu uye zvishongedzo. Ivo vanoshandura 115VAC 60Hz yekupinda kuita sere (8) yakazvimirira inodzorwa 12VDC kana 24VDC yakachengetedzwa inobuda. Access Power Controller's mbiri yekupinza dhizaini inobvumira simba kutungamirwa kubva maviri (2) fekitori-yakamisikidzwa yakazvimirira yakaderera vol.tage 12 kana 24VDC Altronix magetsi ekupa kune masere (8) akazvimirira anodzora fuse (AL1024NKA8) kana PTC (AL1024NKA8D) akachengetedzwa zvabuda. Simba rinobuda rinogona kushandurwa kuita yakaoma fomu "C" mazita. Mabudiro anoitwa neakavhurika muunganidzi sink, anowanzo kuvhurika (NO), anowanzo kuvharwa (NC) yakaoma trigger yekuisa, kana nyoro inobuda kubva kuAccess Control System, Card Reader, Keypad, Push Button, PIR, etc. AL1024NKA8(D) ichaita simba renzira kune zvakasiyana-siyana zvekupinda kutonga hardware zvishandiso zvinosanganisira Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs ichashanda mune zvose Fail-Safe uye / kana Fail-Secure modes. Iyo FACP Interface inogonesa Emergency Egress, Alarm Monitoring, kana inogona kushandiswa kumutsa mimwe michina yekubatsira. Iyo yemoto alarm yekubvisa ficha inosarudzwa yega kune chero kana ese masere (8) zvinobuda. Iyo spade yekubatanidza inokutendera iwe kuti daisy cheni simba kune akawanda ACMS8(CB) modules. Iyi ficha inobvumidza iwe kugovera simba pamusoro pezvakawanda zvinobuda kune makuru masisitimu.

Kumira-ne Zvinotsanangurwa (zvese zvazvino zvinoratidzwa)

Output	15 min. ye Stand-by uye 5 min. yeAlarm	4 hr. ye Stand-by uye 5 min. yeAlarm	24 hr. ye Stand-by uye 5 min. yeAlarm	60 hr. ye Stand-by uye 5 min. yeAlarm
24VDC/12AH Bhatiri	Stand-By = 8A Alarm = 10A	Stand-By = 1.5A Alarm = 10A	Mira-By = 200mA Alarm = 10A	Mira-By = 100mA Alarm = 10A
Output	15 min. ye Stand-by uye 5 min. yeAlarm	4 hr. ye Stand-by uye 5 min. yeAlarm	24 hr. ye Stand-by uye 15 min. yeAlarm	60 hr. ye Stand-by uye 15 min. yeAlarm
24VDC/65AH Bhatiri	–	Stand-By = 8.0A Alarm = 10A	Stand-By = 1.5A Alarm = 10A	Mira-By = 500mA Alarm = 10A

YeKupinda Kudzora maapplication, bhatiri huwandu hwe10A inopa ikozvino - 1 hr. ye24VDC/12AH bhatiri, 6.5 maawa. ye24VDC/65AH bhatiri. Ona peji rekuverenga saizi yebhatiri pazasi kune mamwe mabhatiri.

A. AL1024NKA8(D) kushandiswa kwemukati ikozvino (kumira-ne) ________________ 0.05 A
B. Kuremedza kushandiswa kwemazuva ano (kumira-ne) _______________ A

C. Nguva yekumira inodiwa (maawa) ________________ H
D. Kuwanda kwebhatiri kunodiwa pakumira-pa (A+B)*C ________________ AH

E. AL1024NKA8(D) kushandiswa kwesimba mukati (Aramu) ________________ 0.05 A
F. Rodha mashandisirwo azvino (Alarm) ________________ A

G. Nguva yealarm (Maawa; 15 Min. = 0.25 Awa) (Aramu) ________________ H
H. Kukwana kwebhatiri kunodiwa paAramu (E+F)*G ________________ AH

I. Huwandu hwebhatiri rakaverengerwa D+H ________________ AH
J. Kukwana kwebhatiri kunodiwa I*1.8 (safety factor) ________________ AH

Cherechedza: AL1024NKA8(D) magetsi akagadzirwa kuti ashande nemabhatiri anosvika 65AH. Ndokumbira utarise: mutsetse [I] haufanirwe kudarika 36AH.
Iwe unofanirwa kuderedza kana kumira-nezvino kushandiswa kana kumira-nenguva kuitira kuti uite zvinoenderana nezvinodiwa. Kuti uone saizi chaiyo yebhatiri ndapota mutsara wakatenderedzwa [J] kune iri pedyo yakakura saizi yebhatiri (semuenzaniso 3.5 AH = 4.0 AH).

Zvinotsanangurwa

Zvinopinza

AL1024ULXB2:
- 115VAC, 60Hz, 4.2A.

ACMS8/ACMS8CB:
- Zvisere (8) zvinokonzeresa:
  - a) Kazhinji kuvhurika (NO) zvekushandisa (dry contacts).
  - b) Kazhinji yakavharwa (NC) mapipu (dry contacts).
  - c) Vhura zvekuunganidza sink inputs.
  - d) Wet Input (5VDC - 24VDC) ine 10K resistor
  - e) Chero kusanganiswa kwezviri pamusoro.

Zvinobuda:

Simba:
- 12VDC kana 5VDC kusvika 6A, 24VDC kusvika 10A (240W yakazara simba).
- Kupfuuratage kudzivirirwa.
ACMS8:
- Fuse-yakadzivirirwa inobuda yakayerwa @ 2.5A painobuda, isina-simba-inogumira. Zvose zvinobuda 6A max. Usapfuure chiyero chemagetsi ega ega.
ACMS8CB:
- PTC-yakadzivirirwa inobuda yakatemerwa @ 2A pane inobuda, Kirasi 2 simba-shoma. Zvose zvinobuda 6A max. Usapfuure chiyero chemagetsi ega ega.
- Zvisere (8) zvinosarudzwa zvakazvimirira zvinodzorwa zvinobuda kana zvisere (8) zvakazvimiririra zvakadzora Fomu "C" relay mabudiro (ona pazasi kuti uwane ratings):
  - a) Fail-Safe uye/kana Fail-Chengetedza magetsi kubuda.
  - b) Fomu "C" relays yakatarwa @ 2.5A. 12, 24VDC, 0.6 Power Factor (ACMS8 chete).
  - c) Ebetsero magetsi anobuda (asina kuchinjika).
  - d) Chero kusanganiswa kwezviri pamusoro.
Yega inobuda inogona kusetwa kune OFF chinzvimbo chesevhisi (output jumper yakaiswa kune yepakati chinzvimbo). Haishande kune Dry Contact application.
Chero pane masere (8) fuse/PTC-akachengetedzwa magetsi anobuda anogona kusarudzwa kutevera simba Input 1 kana Input 2. Output voltage yega yega inobuda yakafanana neyekuisa voltage yezvakasarudzwa.
Surge kudzvinyirira.

Fuse/PTC Ratings:

AL1024ULXB2:
- Fuse inopinza inonzi 5A/250V.
- Battery fuse inonzi 15A/32V.
ACMS8:
- Fuse huru yekupinza yakayerwa 15A/32V.
- Mafiyuzi anobuda akatemerwa 3A/32V.
ACMS8CB:
- Main input PTC yakarongwa 9A.
- Kubuda kwePTCs kwakarongwa 2A.

Battery Backup:

Yakavakirwa-mukati charger yeakavharirwa lead asidhi kana gel mhando mabhatiri.
Chinja otomatiki kune bhatiri rakamira kana AC yatadza.
Maximum charge ikozvino 3.6A.

Zero voltage inodonha kana yachinjirwa kune bhatiri backup.

Kutarisira:

AC inotadza kutarisa (fomu "C" mazita).

Kutarisirwa kwakaderera kwebhatiri (fomu "C" mazita).
Tarisiro yekuvapo kwebhatiri (fomu "C" mazita).

Moto Alarm Dimbura:

Moto Alarm disconnect (latching kana kusa-latching) inosarurwa yega kune chero kana ese ezvisere (8) zvinobuda. Moto Alarm bvisa sarudzo dzekuisa:
- a) Kazhinji kuvhura [NO] kana kuvharika [NC] yakaoma kuonana yekupinda. Polarity reversal input kubva kuFACP signing circuit.
FACP yekupinda WET yakayerwa 5-30VDC 7mA.

FACP yekupinda EOL inoda 10K kupera kwemutsara wekupokana.
FACP inoburitsa relay [NC]:
Pamwe Dry 1A/28VDC, 0.6 Power Factor kana 10K kuramba ne [EOL JMP] yakasimba.

Visual Indicators:

AL1024ULXB2:
- Green AC LED: Inoratidza 115VAC iripo.
- Red DC LED: Inoratidza DC kubuda.

ACMS8(CB):
- Red LEDs: Ratidza zvinobuda zvinokonzeresa.
- Bhuruu LED: Inoratidza FACP kubviswa kunokonzerwa.
- Individual Voltage LEDs: Ratidza 12VDC (Green) kana 24VDC (Red).

Environmental:

Kushanda tembiricha: 0ºC kusvika 49ºC ambient.

Humidity: 20 kusvika 85%, isina-condensing.

Enclosure Dimensions (inenge H x W x D): 15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm).

Installation Instructions

Wiring nzira dzichaenderana neNational Electrical Code/NFPA 70/NFPA 72/ANSI, Canadian Electrical Code uye nemakodhi ese emuno nezviremera zvine masimba. Chigadzirwa chakagadzirirwa kushandiswa kwemukati chete.

Mount unit munzvimbo yaunoda. Maka uye gadzira maburi mumadziro kuti uenderane nepamusoro makiyi maburi ari mukati mekuvharirwa. Isa zvisungo zviviri zvekumusoro nema screws mumadziro ane sikuruwa misoro yakabuda. Isa chivharo chepamusoro makiyi maburi pamusoro pemasikiru maviri epamusoro, nhanho uye chengetedza. Maka nzvimbo yemaburi maviri ezasi. Bvisa yakavharirwa. Dhobora maburi ezasi uye woisa ma fasteners maviri. Isa makiyi epamusoro emuvharo pamusoro pemakona maviri epamusoro. Isai maviri ezasi screws uye ita shuwa kuomesa ese screws (Enclosure Dimensions, pg. 12). Chengetedza yakavharirwa pasi pevhu.
Iva nechokwadi chokuti zvose zvinobuda zvinosvetuka [PWR1] - [PWR8] zvakaiswa mu OFF (pakati) nzvimbo (Fig. 1, pg. 3).
Batanidza isina kuchinjika AC simba (115VAC 60Hz) kumateminari akaiswa [L, N] (Fig. 4a, pg. 5). Green "AC" LED pane magetsi bhodhi inobatidza. Chiedza ichi chinogona kuoneka kuburikidza ne LED lens pamusuwo weiyo yakavharirwa. Shandisa 14 AWG kana yakakura kune ese magetsi ekubatanidza. Chengetedza green wire lead kune ivhu pasi. Chengetedza wiring ine simba-inogumira yakaparadzana kubva kune isina simba-inogumira wiring (115VAC 60Hz Input, Battery Wire). Minimum 0.25” nzvimbo inofanira kupihwa.
CHENJERERO: Usabata nhengo dzesimbi dziri pachena. Vhara simba redunhu rebazi usati waisa kana kusevha midziyo. Iko hakuna zvikamu zvinoshandiswa nemushandisi mukati. Revera kuisirwa uye sevhisi kune vanokwanisa sevhisi vashandi.

Isa imwe neimwe inobuda [OUT1] - [OUT8] kunzira simba kubva Input 1 kana 2 (Fig. 1, pg. 3).
Cherechedza: Kuyera kubuda voltage pamberi pekubatanidza zvishandiso. Izvi zvinobatsira kudzivisa kukanganisa kunogona kuitika.
Dzima simba usati wabatanidza zvishandiso.
Sarudzo dzekubuda: AL1024NKA8(D) ichapa anosvika masere (8) akachinja magetsi kana masere (8) yakaoma fomu "C" kubuda, kana chero musanganiswa wezvose zviri zviviri switched simba uye fomu "C" zvinobuda, pamwe masere (8) asina kuchinjika. ebetsero simba kubuda.
- Akachinja Power outputs:
  Batanidza iyo isina kunaka (-) kupinza kwemudziyo uri kupihwa simba kune terminal yakanyorwa [COM].
  - YeFail-Safe operation batanidza iyo yakanaka (+) inopinza yemudziyo uri kufambiswa kune terminal yakanyorwa [NC].
  - YeFail-Secure operation batanidza iyo yakanaka (+) yekupinda yemudziyo uri kufambiswa kune terminal yakanyorwa [NO].
- Fomu "C" zvabuda:
  Kana mafomu e "C" achidiwa, jumper inoenderana (1-8) inofanira kuiswa munzvimbo ye OFF (Fig. 7, p. 9). Neimwe nzira, iyo inoenderana inobuda fuse (1-8) inogona kubviswa (AL1024NKA8 chete). Batanidza zvisina kunaka (-) zvemagetsi emagetsi zvakananga kune yekukiya mudziyo. Batanidza iyo yakanaka (+) yemagetsi emagetsi kune terminal yakanyorwa [C].
  - YeFail-Safe operation batanidza iyo yakanaka (+) yemudziyo uri kufambiswa kuterminal yakanyorwa kuti [NC].
  - YeFail-Secure operation batanidza iyo yakanaka (+) yemudziyo uri kufambiswa kuterminal yakanyorwa [NO]. Dry contacts rated @ 2.5A, 28VDC.
- Ebetsero Simba rinobuda (isina kuchinjika):
  Batanidza zvakanaka (+) mugadziriso wemudziyo uri kufambiswa kuterminal yamaka [C] uye yakaipa (-) yemudziyo uri kufambiswa kuterminal yakamaka [COM]. Kubuda kunogona kushandiswa kupa simba kune vaverengi vemakadhi, keypads nezvimwe.
Batidza simba guru mushure mekunge zvishandiso zvese zvabatanidzwa.
Input Trigger sarudzo:

Cherechedza: Kana Fire Alarm ikadimburwa ikasashandiswa, batanidza 10K ohm resistor kune materminal akanyorwa [GND neEOL], uye batanidza jumper kune materminals akaiswa [GND, RST].
Kazhinji Vhura (NO) Input:
Sraidhi yekupinza kudzora mantiki DIP chinja ichiisa OFF chinzvimbo che[Chinja 1-8] (Mufananidzo 2, kurudyi). Batanidza waya dzako kumaterminals akamakwa [+ INP1 –] ku [+ INP8 –].
Kazhinji Yakavharwa (NC) Inopinza:
Sraidhi yekupinda kudzora mantiki DIP chinja kupinda ON chinzvimbo che[Chinja 1-8] (Mufananidzo 2, kurudyi). Batanidza waya dzako kumaterminals akamakwa [+ INP1 –] ku [+ INP8 –].
Vhura Collector Sink Input:
Batanidza yakavhurika yekunyura sink yekuisa kune terminal yakanyorwa [+ INP1 -] ku [+ INP8 -].
Mvura (Voltage) Input Configuration:
Kunyatsocherechedza polarity, batanidza voltage input trigger waya uye yakapihwa 10K resistor kumaterminals akaiswa [+ INP1 –] ku [+ INP8 –].
Kana kushandisa voltage kukonzeresa kupinza - isa inoenderana INP Logic switch kune iyo "OFF" chinzvimbo
Kana kubvisa voltage kukonzeresa kupinza - isa inoenderana INP Logic switch kune iyo "ON" chinzvimbo

Fire Alarm Interface sarudzo:

Iyo inowanzovharwa [NC], inowanzovhura [NO] yekupinda kana polarity reversal input kubva kuFACP siginacha wedunhu inokonzeresa zvakasarudzwa. Kugonesa FACP Disconnect yezvinobuda batidza chinowirirana DIP switch [SW1-SW8] KUBATSIRA. Kudzima FACP disconnect yezvinobuda dzima DIP switch inoenderana [SW1-SW8] DZIMA. Switch inowanikwa zvakananga kuruboshwe kweMoto Alarm Interface Terminals.
Kazhinji Open Input:
Waya yako FACP relay uye 10K resistor in parallel pamaterminals akaiswa [GND] uye [EOL].
Kazhinji Yakavharwa Inopinza:
Waya yako FACP relay uye 10K resistor munhevedzano pamaterminal akanyorwa [GND] uye [EOL].
FACP Inoratidza Circuit Input Trigger:
Batanidza yakanaka (+) uye yakaipa (-) kubva paFACP inosaina dunhu rinobuda kune materminal akanyorwa [+ FACP -]. Batanidza iyo FACP EOL kune materminal akamakwa [+ RET –] (polarity inoratidzwa mune aramu mamiriro).
Isiri-Latching Fire Alarm Dimbura: Batanidza jumper kumaterminal akanyorwa [GND, RST].
FACP Dry NC yakabuda:
Batanidza mudziyo waunoda kuti ukonzereswe neiyo unit yakaoma yekubatanidza inobuda kune materminal akaiswa [NC] uye [C]. Kana [EOL JMP] ichichengetwa yakasimba, inobuda ndeye 0 Ohm kuramba mune yakajairika mamiriro. Kana [EOL JMP] yakadimburwa, 10k kuramba inopfuudzwa kune inotevera mudziyo kana iri mune yakajairika mamiriro.
Battery Connections (Mufananidzo 6, peji 8):
Kune US Access Control application mabhatiri anosarudzika. Mabhatiri anodiwa pakuisirwa kweCanada (ULC-S319). Kana mabhatiri akasashandiswa, kurasikirwa kwe AC kunozokonzera kurasikirwa kwekubuda kwevoltage. Kana kushandiswa kwema-stand-by mabhatiri kunodiwa, anofanira kunge ari lead acid kana gel rudzi. Batanidza bhatiri kumaterminals akaiswa [- BAT +] (Fig. 4g, pg. 6). Shandisa maviri (2) 12VDC mabhatiri akabatanidzwa munhevedzano ye24VDC oparesheni (yebhatiri inotungamira inosanganisirwa). Shandisa mabhatiri – Casil CL1270 (12V/7AH), CL12120 (12V/12AH), CL12400 (12V/40AH), CL12650 (12V/65AH) mabhatiri kana UL anozivikanwa BAZR2 neBAZR8 mabhatiri echiyero chakakodzera.

Bhatiri uye AC Supervision zvabuda (Fig. 4, peji 8):
Batanidza midziyo yekuzivisa zviziviso yakakodzera kune materminal akanyorwa [AC FAIL & BAT FAIL] (Fig. 4b, pg. 5) supervisory relay zvinobuda. Shandisa 22 AWG kusvika 18 AWG yeAC Fail & Low/No Battery reporting.
Kuti unonoke kushuma kusvika ku6 hrs., cheka "AC Kunonoka" jumper uye reset simba kune unit (Fig. 4f, pg. 6).
Moto Alarm Dimbura (Mufananidzo 4c, peji 6):
- Kugonesa Fire Alarm Disconnect isa DIP switch [Shutdown] kuenda ON chinzvimbo.
- Kuti udzime Fire Alarm Dimbura seta DIP switch [Shutdown] kuenda ku OFF chinzvimbo.
Kuiswa kwe tamper switch:
Mount UL Yakanyorwa tamper switch (Altronix modhi TS112 kana yakaenzana) pamusoro peiyo yakavharirwa. Svetera iyo tamper switch bracket kumucheto kweiyo yakavharirwa inenge 2" kubva kurudyi (Fig. 6a, pg. 8). Batanidza tamper chinja wiring kune Access Control Panel yekupinda kana yakakodzera UL Yakanyorwa yekurekodha mudziyo. Kuti uvhure mucherechedzo wearamu vhura gonhi renzvimbo yakavharirwa.

Maintenance

Yuniti inofanirwa kuyedzwa kanenge kamwe pagore kuti iite basa rakakodzera sezvinotevera:

Kubuditsa Voltage Muedzo: Mumamiriro ezvinhu akajairwa, DC inobuda voltage inofanirwa kuongororwa kuti ine voltage level.
Battery Test: Mumamiriro ezvinhu akajairwa tarisa kuti bhatiri razara chaji, tarisa yakataurwa voltage zvese pachiteshi chebhatiri uye pabhodhi zviteshi zvakatemwa [- BAT +] kuona kuti hapana kutyora mutambo dzekubatanidza bhatiri.

Cherechedza: Maximum kuchaja ikozvino pasi pezvinobudiswa ndeye 3.6A.
Cherechedza: Hupenyu hwebhatiri hunotarisirwa makore mashanu; zvisinei, zvinokurudzirwa kushandura mabhatiri mumakore 5 kana pasi kana zvichidiwa

Mufananidzo 4 - AL1024ULXB2 Board Configuration

Akatungamirira Diagnostics

AL1024ULXB2 - Power Supply Board

Tsvuku (DC)	Green (AC)	Power Supply Status
ON	ON	Yakajairika mamiriro ekushanda.
ON	DZIMA	Kurasika kweAC. Batiri rekumira riri kupa simba.
DZIMA	ON	Hapana DC inobuda.
DZIMA	DZIMA	Kurasika kweAC. Radzimwa kana kushaya bhatiri rakamira. Hapana DC inobuda.

ACMS8 uye ACMS8CB Access Power Controller

LED	ON	DZIMA
LED 1- LED 8 (Dzvuku)	Output relay(s) de-energized.	Output relay(s) simba.
FACP	FACP inopinza yakakonzeresa (alarm mamiriro).	FACP yakajairika (isina-alarm mamiriro).
Green Output 1-8	12VDC	–
Red Output 1-8	24VDC	–

Terminal Identification

AL1024ULXB2 - Power Supply Board

Terminal Legend	Basa/ Tsanangudzo
L, N	Batanidza 115VAC kune aya materminal: L kusvika kupisa, N kusarerekera (Fig. 4a, pg. 6).
+ DC -	Fekitari yakabatana neACMS8(CB) (Fig. 4d, pg. 6).
AC Fail NC, C, NO	Inoshandiswa kuzivisa kurasikirwa kwesimba reAC, egconnect kune inonzwika mudziyo kana alarm panel. Relay kazhinji inopihwa simba kana AC simba riripo. Contact rating 1A @ 28VDC. AC kana brownout kutadza kunotaurwa mukati meminiti 1 yechiitiko. Kunonoka kushuma kweanosvika 6 hrs., cheka "AC Kunonoka" jumper uye reset simba kuyuniti. (Fig. 4f, pg. 6).
Bat Fail NC, C, NO	Inoshandiswa kuratidza kuderera kwebhatiri, semuenzaniso batanidza kune alarm panel. Relay kazhinji inopihwa simba kana DC simba iripo. Contact rating 1A @ 28VDC. Bhatiri rakabviswa rinotaurwa mukati meminiti imwe. Kubatanidza bhatiri kunoshumwa mukati meminiti imwe. Yakaderera bhatiri chikumbaridzo: inenge 21VDC (Mufananidzo 4b, peji 6).
– BAT +	Kubatana kwebhatiri. Yakanyanya kuchaja ikozvino 3.6A (Fig. 4c, pg. 6).

ACMS8 uye ACMS8CB Access Power Controller

Terminal Legend	Basa/ Tsanangudzo
+ PWR1 -	Fekitari yakabatana kune AL1024ULXB2. Usashandise materminals aya.
+ PWR2 -	Fekitari yakabatana neVR6 voltage regulator. Usashandise materminals aya.
+ INP1 - kuburikidza + INP8 -	Masere (8) anodzorwa akazvimirira Kazhinji Kuvhurika (NO), Kazhinji Kuvharwa (NC), Vhura Muunganidzi Sink kana Wet Input Triggers.
C, NC	FACP Dry NC yakabuda yakarongwa 1A/28VDC @ 0.6 Power Factor. Kirasi 2 simba-shoma. Iine EOL JMP yakasimba, ichapa 10k kuramba mune yakajairika mamiriro.
GND, RST	FACP interface yatching kana kusa-latching. HAPANA yakaoma kuisa. Kirasi 2 simba-shoma. Kupfupikiswa kune isiri-latching FACP interface kana Latch FACP reset.
GND, EOL	EOL Inotariswa FACP Input zviteshi zve polarity reversal FACP basa. Kirasi 2 simba-shoma.
-F, + F, - R, + R	FACP Signaling Circuit Input uye Return terminals. Kirasi 2 simba-shoma.
Kubuda 1 kuburikidza Kubuda 8 Kwete, C, NC, COM	Zvisere (8) zvinosarudzwa zvakazvimiririra zvinodzorwa zvabuda [Fail-Safe (NC) kana Fail-Secure (NO)] uye masere (8) akazvimirira anodzora Fomu “C” Relay zvabuda.

Mufananidzo 6 - AL1024NKA8(D)

CHENJERERO: Shandisa mabhatiri maviri (2) 12VDC akamira-ne.

Chengetedza magetsi-akaganhurirwa wiring akaparadzana neasina-simba-shoma. Shandisa zvishoma 0.25” nzvimbo.

12AH Rechargeable mabhatiri ndiwo mabhatiri makuru anogona kukwana mune ino yakavharwa.
A UL-yakanyorwa bhatiri rekunze rakavharirwa rinofanira kushandiswa kana uchishandisa 40AH kana 65AH mabhatiri.

Yakajairika Anwendung Diagram

Hook-Up Diagrams

Mufananidzo 8 - Daisy-chaining imwe kana kupfuura ACMS8 (CB) zvikamu. EOL Jumper [EOL JMP] inofanira kuiswa munzvimbo yeEOL. Non-Latching.
Mufananidzo 9 - Daisy-chaining imwe kana kupfuura ACMS8 (CB) zvikamu. EOL Jumper [EOL JMP] inofanira kuiswa munzvimbo yeEOL. Latching Single Reset.
Fig. 10 – Daisy chaining one or more ACMS8(CB) units. EOL Jumper [EOL JMP] inofanira kuiswa munzvimbo yeEOL. Latching Individual Reset.

Hook-Up Diagrams

Fig. 11 - Polarity reversal input kubva ku FACP inoratidzira circuit output (polarity inotaridzirwa mune alarm conditiion). Non-Latching
Fig. 12 - Polarity reversal input kubva ku FACP inoratidzira circuit output (polarity inotaridzirwa mumamiriro e alarm). Latching

Fig. 13 - Kazhinji Yakavharwa trigger input (Non-Latching).
Fig. 14 - Kazhinji Yakavharwa trigger input (Latching).
Fig. 15 - Kazhinji Open trigger input (Non-Latching)

Fig. 16 - Kazhinji Open trigger input (Latching).

Enclosure Dimensions (BC400)

15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm)

Altronix haina mhosva kune chero zvikanganiso zve typographical. 140 58th Street, Brooklyn, New York 11220 USA

foni: 718-567-8181
fakisi: 718-567-9056

websaiti: www.altronix.com
e-mail: info@altronix.com
Hupenyu hwese Warranty

Zvinyorwa / Zvishandiso

Altronix AL1024NKA8 Series Dual Output Access Power Controllers [pdf] Installation Guide
AL1024NKA8, AL1024NKA8D, AL1024NKA8 Series Dual Output Access Power Controllers, Dual Output Access Power Controllers, Access Power Controllers, Dual Output Power Controllers, Power Controllers.

References

User Manual

Altronix AL1024NKA8 Series Dual Output Access Power Controllers

Overview