Altronix AL1024NKA8 Fa'asologa Lua Avanoa Avanoa Pule Pule Fa'atonu Taiala

Altronix AL1024NKA8 ma AL1024NKA8D tufaina ma fesuia'i le malosiaga e maua ai faiga pulea ma mea faaopoopo. Latou te fa'aliliuina se fa'aoga 115VAC 60Hz i totonu o le valu (8) fa'atonu tuto'atasi 12VDC po'o le 24VDC galuega fa'asaoina. O le mamanu fa'aoga lua a le Access Power Controller e mafai ai ona fa'atonu le paoa mai le lua (2) falegaosimea-fa'apipi'i tuto'atasi vol voltagu 12 po'o le 24VDC Altronix sapalai eletise i le valu (8) fa'atonuga fa'atonu (AL1024NKA8) po'o le PTC (AL1024NKA8D) galuega fa'asaoina. E mafai ona fa'aliliuina mea e maua ai le malosi i fa'amamago fa'afeso'ota'iga "C". E fa'agaoioia mea e ala ile fa'agogo o le aoina, e masani ona matala (LEAI), e masani ona tapuni (NC) mea fa'aoso fa'atutu, po'o le susu mea mai le Access Control System, Card Reader, Keypad, Push Button, PIR, etc. AL1024NKA8(D) will auala malosi i le tele o avanoa e pulea masini masini e aofia ai Mag Loka, Eletise Strikes, Magnetic Faitotoa Uu, ma isi mea o le a faagaoioia i le Fail-Saogalemu ma/poʻo Fail-Secure modes. O le FACP Interface e mafai ai le Faʻalavelave Faʻafuaseʻi, Mataʻituina o le Alarm, pe mafai foi ona faʻaaogaina e faʻaoso ai isi masini fesoasoani. O le fa'aaliga motusia fa'ailo afi e mafai ona filifilia ta'ito'atasi mo so'o se mea po'o galuega uma e valu (8). O so'o so'o e fa'atagaina oe e fa'amalo le filifili daisy i le tele ACMS8(CB) modules. O lenei vaega e mafai ai ona e tufatufaina atu le mana i luga o le tele o galuega faatino mo faiga tetele.

Fa'amatalaga tu'u i luga (aofa'i o lo'o fa'aalia)

Tuuina atu	15 minu. o Stand-by ma le 5 min. o Alalaga	4 itula. o Stand-by ma le 5 min. o Alalaga	24 itula. o Stand-by ma 5 minu. o Alalaga	60 itula. o Stand-by ma 5 minu. o Alalaga
24VDC/12AH Ma'a	Tutu-By = 8A Alaala = 10A	Tutu-By = 1.5A Alaala = 10A	Tutu-By = 200mA Alaala = 10A	Tutu-By = 100mA Alaala = 10A
Tuuina atu	15 minu. o Stand-by ma le 5 min. o Alalaga	4 itula. o Stand-by ma le 5 min. o Alalaga	24 itula. o Stand-by ma le 15 min. o Alalaga	60 itula. o Stand-by ma le 15 min. o Alalaga
24VDC/65AH Ma'a	–	Tutu-By = 8.0A Alaala = 10A	Tutu-By = 1.5A Alaala = 10A	Tutu-By = 500mA Alaala = 10A

Mo talosaga Pulea Avanoa, gafatia maa mo le 10A sapalai i le taimi nei - 1 itula. mo le maa 24VDC/12AH, 6.5 itula. mo 24VDC/65AH maa. Va'ai le pepa o galuega fa'atatau o le tele o ma'a i lalo mo isi ma'a.

A. AL1024NKA8(D) fa'aogaina i totonu o le taimi nei (tu'i i luma) ________________ 0.05 A
B. Uta i le taimi nei le taumafaina (tumau i luma) ________________ A

C. Taimi tu'itu'i mana'omia (itula) ________________ H
D. E mana'omia le malosi o le ma'a mo le tu'i (A+B)*C ________________ AH

E. AL1024NKA8(D) fa'aogaina o le eletise i totonu (Fa'ailo) ________________ 0.05 A
F. Uta i le taimi nei le fa'aaogaina (Fa'ailo) ________________ A

G. Umi o le fa'alogo (Ila; 15 Min. = 0.25 Itula) (Fa'ailo) ________________ H
H. E mana'omia le malosi o le ma'a mo le Fa'ailoga (E+F)*G ________________ AH

I. Aofa'i fuafuaina gafatia maa D+H ________________ AH
J. E mana'omia le malosi o le ma'a I*1.8 (tulaga saogalemu) ________________ AH

Fa'aaliga: AL1024NKA8(D) sapalai eletise ua mamanuina e galue ma maa e oo atu i le 65AH. Faamolemole ia matau: laina [I] e le tatau ona sili atu i le 36AH.
E tatau ona fa'aitiitia le fa'aogaina o le taimi nei po'o le taimi tu'i ina ia fa'amalieina le mana'oga. Ina ia iloa tonu le telē o le maa fa'amolemole laina lapotopoto [J] i le lapo'a fa'atalata lata ane lapo'a masani maa (fa'ata'ita'iga 3.5 AH = 4.0 AH).

Fa'amatalaga

Ulufale:

AL1024ULXB2:
- 115VAC, 60Hz, 4.2A.

ACMS8/ACMS8CB:
- E valu (8) mea e fa'aoso ai:
  - a) E masani ona tatala (LEAI) mea fa'aoga (feso'ota'iga mago).
  - b) E masani ona tapuni (NC) mea fa'aoga (fa'afeso'ota'i mago).
  - c) Tatala mea e teu ai pusa.
  - d) Ulufale susu (5VDC - 24VDC) faʻatasi ma le 10K teteʻe
  - e) Soo se tuufaatasiga o mea o loo i luga.

Fa'atino:

Malosiaga:
- 12VDC poʻo le 5VDC e oʻo atu i le 6A, 24VDC e oʻo atu i le 10A (240W le malosi atoa).
- Fouvaletagu puipuiga.
ACMS8:
- Fuse-puipuia galuega fa'amauina @ 2.5A i le gaosiga, e le fa'atapula'aina le malosi. Aofa'i galuega faatino 6A max. Aua ne'i sili atu i fua fa'atatau o le eletise.
ACMS8CB:
- PTC-puipuia galuega faatino fa'amauina @ 2A i galuega faatino, Vasega 2 malosi-faatapula'a. Aofa'i galuega faatino 6A max. Aua ne'i sili atu i fua fa'atatau o le eletise.
- E valu (8) galuega faatino e mafai ona filifili tutoatasi po'o le valu (8) fa'atonu fua fa'atatau o le Pepa "C" (silasila i lalo mo fa'avasegaga):
  - a) Fa'aletonu-Saogalemu ma/po'o le Fa'aletonu-Saogalemu malosiaga.
  - b) Fa'ailoga "C" fa'amauina @ 2.5A. 12, 24VDC, 0.6 Power Factor (ACMS8 na'o).
  - c) Malosiaga fesoasoani (e le'i sui).
  - d) Soo se tuufaatasiga o mea o loo i luga.
E mafai ona seti galuega ta'ito'atasi ile tulaga OFF mo le tautuaina (fa'aoso oso i le tulaga ogatotonu). E le fa'aoga ile Dry Contact applications.
So'o se mea e valu (8) fuse/PTC-puipuia le eletise e mafai ona filifili e mulimuli i le mana Ulufale 1 po'o Ulufale 2. Output voltagu o galuega faatino taitasi e tutusa ma le voltagu o mea na filifilia.
Taofi si'itia.

Fuse/PTC Fa'ailoga:

AL1024ULXB2:
- Fuse fa'aulu fa'atatau 5A/250V.
- Fuse ma'a fa'amauina 15A/32V.
ACMS8:
- O fuse fa'aoga autu e fa'atatau i le 15A/32V.
- O fuse fa'aulu e fa'atatau i le 3A/32V.
ACMS8CB:
- O le fa'aoga autu o le PTC e fa'amauina le 9A.
- PTCs Output ua fa'amauina 2A.

Fa'aola ma'a:

Fausia-i le charger mo faʻamau faʻamau faʻamauina acid po o gel ituaiga.
Otometi fesuiaʻi i luga e tu i le maa pe a le faia AC.
Ole maualuga ole tau ole 3.6A.

Zero voltage pa'u pe a sui i le maa faaleoleo.

Vaavaaiga:

Fa'atonu le AC (faiga "C" feso'ota'iga).

Maualalo le vaavaaia o maa (faiga "C" fesootaiga).
Vaavaaiga o le i ai o le maa (faiga "C" fesootaiga).

Tatala Fa'ailoga Tinei Mu motumotu:

Ta'oto'oto le Ala Alamu (fa'amau po'o le le fa'amauina) e mafai ona filifilia ta'ito'atasi mo so'o se mea po'o galuega uma e valu (8). Fa'ailoga afi motu'ese filifiliga fa'aoga:
- a) E masani ona tatala [LEAI] po'o le masani ona tapuni [NC] mea fa'afeso'ota'i mago. Faiga fa'aliliuga fa'apolokalame mai le fa'ailoga fa'ailoga FACP.
FACP fa'aoga WET ua fa'amauina 5-30VDC 7mA.

FACP fa'aoga EOL mana'omia le 10K fa'ai'uga o le laina fa'atete.
FACP fa'asolo atu [NC]:
Po'o le Dry 1A/28VDC, 0.6 Power Factor po'o le 10K tete'e fa'atasi ai ma le [EOL JMP] fa'amautu.

Fa'ailoga Vaaia:

AL1024ULXB2:
- LED AC Green: Fa'ailoa 115VAC o iai.
- MULAU DC LED: Fa'ailoa DC galuega.

ACMS8(CB):
- Uila Mumu: Fa'ailoa galuega ua fa'aoso.
- LED Blue: Fa'ailoa ai le motusia o le FACP ua fa'aoso.
- Taitoatasi Voltagu LED: Fa'ailoa le 12VDC (Green) po'o le 24VDC (Red).

Si'osi'omaga:

O le vevela o galuega: 0ºC i le 49ºC ambient.

Susūsū: 20 i le 85%, e le faʻafefe.

Fua Fa'amau (tulaga H x W x D): 15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm).

Fa'atonuga fa'apipi'i

E tatau ona o gatasi auala tau uaea ma le National Eletise Code/NFPA 70/NFPA 72/ANSI, le Canadian Eletise Code ma tulafono fa'alotoifale uma ma pulega o lo'o i ai le pule'aga. O oloa e fa'amoemoe mo na'o totonu.

Fa'amau le iunite i le nofoaga e mana'omia. Faailoga ma mua'i vili pu i le puipui e laina ai ma pu ki pito i luga e lua i totonu o le pa. Fa'apipi'i ni fa'amau pito i luga e lua ma fa'avili i le puipui ma fa'aoso fa'aulu ulu. Tuu pu ki pito i luga o le pa i luga o sikulima pito i luga e lua, faʻamautu ma faʻamautu. Faailoga le tulaga o pu e lua pito i lalo. Aveese le pa. vili pu pito i lalo ma fa'apipi'i fa'amau e lua. Tuu pu ki pito i luga o le pa i luga o sikulima pito i luga e lua. Fa'apipi'i fa'amau pito i lalo e lua ma fa'amautinoa ua fa'amau uma fa'avili (Liga Fa'amau, itulau 12). Puipui malu i le eleele eleele.
Ia mautinoa o lo'o tu'u uma mea osooso [PWR1] – [PWR8] i le tulaga OFF (ogatotonu) (Ata 1, itulau 3).
Fa'afeso'ota'i le mana AC e le'i suiina (115VAC 60Hz) i fa'amau fa'ailoga [L, N] (Ata 4a, itulau 5). O le LED "AC" lanumeamata i luga o le laupapa sapalai o le a ki. E mafai ona iloa lenei malamalama e ala i le tioata LED i le faitotoa o le pa. Fa'aaoga le 14 AWG po'o le tele mo so'otaga eletise uma. Faamautu uaea lanu meamata e tau i le eleele eleele. Taofi uaea fa'atapula'aina le malosi mai uaea le fa'atapula'aina (115VAC 60Hz Input, Uea Ma'a). E tatau ona tu'uina atu le avanoa aupito itiiti e 0.25".
FAATUATUA: Aua ne'i pa'i i vaega u'amea fa'aalia. Tapuni le eletise o le lala a'o le'i fa'apipi'i po'o le tautuaina o meafaigaluega. E leai ni vaega e mafai ona fa'aaogaina i totonu. Fa'asino le fa'apipi'iina ma le tautuaina i tagata faigaluega fa'apitoa.

Seti galuega faatino taitasi [OUT1] – [OUT8] e ave ai le eletise mai le Ulufale 1 po o le 2 (Ata 1, itulau 3).
Fa'aaliga: Fua galuega voltagu a'o le'i fa'afeso'ota'i masini. E fesoasoani lea e aloese ai mai le faaleagaina.
Tape le eletise a'o le'i fa'afeso'ota'i masini.
Filifiliga fa'atino: AL1024NKA8(D) o le a tu'uina atu e o'o atu i le valu (8) fa'aliliuga eletise po'o le valu (8) fa'amamago "C" galuega, po'o so'o se tu'ufa'atasiga uma o le paoa ua fesuia'i ma fau le "C", fa'aopoopo i le valu (8) le fa'aogaina. malosiaga fesoasoani.
- Suia le Malosi galuega:
  Fa'afeso'ota'i le fa'aoga leaga (-) o le masini o lo'o fa'aola i le laina fa'ailoga [COM].
  - Mo le Fail-Safe operation fa'afeso'ota'i le fa'aoga lelei (+) o le masini o lo'o fa'aola i le fa'ailoga ua fa'ailoga [NC].
  - Mo Fail-Secure faagaioiga fa'afeso'ota'i le fa'aoga lelei (+) o le masini o lo'o fa'aola i le laina fa'ailoga [LEAI].
- Fua "C" galuega faatino:
  Pe a mana'omia galuega faatino "C", e tatau ona tu'u le osooso tutusa (1-8) i le tulaga OFF (Ata 7, itulau 9). E le gata i lea, e mafai ona aveese le fuse (1-8) e tutusa (AL1024NKA8). Fa'afeso'ota'i sa'o le leaga (-) o le paoa i le masini loka. Fa'afeso'ota'i le lelei (+) o le sapalai eletise i le laina fa'ailoga [C].
  - Mo le fa'agaioiga Fail-Safe fa'afeso'ota'i le lelei (+) o le masini o lo'o fa'aola i le fa'ailoga ua fa'ailoga [NC].
  - Mo Fail-Secure faagaioiga fa'afeso'ota'i le lelei (+) o le masini o lo'o fa'aola i le fa'ailoga ua fa'ailoga [LEAI]. Feso'ota'iga mamago fa'atatau @ 2.5A, 28VDC.
- Auxiliary Power outputs (le suiina):
  Fa'afeso'ota'i fa'aoga lelei (+) o le masini o lo'o fa'aola i le laina fa'ailoga [C] ma le leaga (-) o le masini o lo'o fa'aola i le fa'ailoga ua fa'ailoga [COM]. E mafai ona faʻaogaina le faʻaogaina e tuʻuina atu ai le mana mo tagata faitau kata, keypads ma isi.
Ki ai le mana autu pe a uma ona feso'ota'i masini uma.
Fa'ailoga Fa'aoso filifiliga:

Fa'aaliga: Afai e le'o fa'aogaina le Alarm Afi, fa'afeso'ota'i le 10K ohm tete'e i fa'amau ua fa'ailoga [GND ma le EOL], fa'aopoopo i ai le so'oga i fa'amau ua fa'ailoga [GND, RST].
Tatala masani (LEAI) Ulufale:
Fa'ase'e le fa'aogaina o le fa'atonuga ole DIP sui i le tulaga OFF mo [Sui 1-8] (Ata 2, i le taumatau). Fa'afeso'ota'i au uaea i fa'amau fa'ailoga [+ INP1 –] i le [+ INP8 –].
E masani ona tapuni (NC) Ulufale:
Fa'ase'e le fa'aoga fa'atonu fa'aoga DIP sui i le tulaga ON mo [Sui 1-8] (Ata 2, i le taumatau). Fa'afeso'ota'i au uaea i fa'amau fa'ailoga [+ INP1 –] i le [+ INP8 –].
Tatala Fa'ato'a Fa'aulu a le Atina'e:
Fa'afeso'ota'i le mea e tu'u ai le pusa o lo'o avanoa i le fa'ailoga ua fa'ailoga [+ INP1 –] i le [+ INP8 –].
Susū (Voltage) Fa'atonuga o mea e fai:
Mataʻituina ma le faʻaeteete polarity, faʻafesoʻotaʻi le voltage fa'aulu uaea fa'aoso ma le 10K tete'e tu'u atu i fa'amau fa'ailoga [+ INP1 –] i le [+ INP8 –].
Afai e faʻaaogaina se voltage fa'aoso fa'aoga - seti le sui INP Logic fetaui i le tulaga "OFF".
Afai e aveese voltage fa'aoso fa'aoga - seti le sui INP Logic fetaui i le tulaga "ON".

Filifiliga Fa'aaliga Fa'alogo afi:

Ole [NC] e masani ona tapuni, e masani ona tatala [LEAI] fa'aoga po'o le fa'aliliuina o le polarity mai le fa'ailoga fa'ailoga FACP o le a fa'aosoina ai galuega ua filifilia. Ina ia fa'agaoioi le FACP Disconnect mo se mea fa'atino, fa'afeso'ota'i le DIP ki [SW1-SW8] ON. Ina ia tape le FACP motusia mo se mea e gaosia, liliu le ki DIP tutusa [SW1-SW8] OFF. O lo'o tu sa'o le Suiga i le itu agavale o le Fa'ailoga Fa'ailoga Afi.
E masani ona tatala Ulufale:
Uea lau fa'ailoga FACP ma le 10K tete'e fa'atutusa i fa'amau fa'ailoga [GND] ma le [EOL].
Fa'auiga tapuni masani:
Uea lau fa'alava FACP ma le 10K tete'e i fa'asologa i fa'amau fa'ailoga [GND] ma le [EOL].
Fa'aoso fa'aoso fa'aoso ole fa'ailoga ole FACP:
Fa'afeso'ota'i le lelei (+) ma le leaga (-) mai le fa'ailoga fa'ailoga FACP i fa'amau fa'ailoga [+ FACP –]. Fa'afeso'ota'i le FACP EOL i fa'amau fa'ailoga [+ RET –] (polarity o lo'o fa'asino i se tulaga fa'ailo).
E le o fa'amauina le Fa'ailoga afi motumotu: Fa'afeso'ota'i se osooso i fa'amau fa'ailoga [GND, RST].
FACP Dry NC galuega faatino:
Fa'afeso'ota'i le masini e mana'omia e fa'aosoina e le masini fa'afeso'ota'i matutu a le iunite i fa'amau fa'ailoga [NC] ma le [C]. A fa'atumauina le [EOL JMP], o le mea e maua mai e 0 Ohm tete'e i se tulaga masani. A tipi le [EOL JMP], o le 10k tete'e o le a pasi atu i le isi masini pe a i ai i se tulaga masani.
Feso'ota'iga Tu'itu'i Ma'a (Ata 6, itulau 8):
Mo talosaga a le US Access Control o maa e filifili. E mana'omia ma'a mo mea fa'apipi'i a Kanata (ULC-S319). A le fa'aogaina maa, o le leiloa o le AC o le a i'u ai i le leiloa o le voltagu. Pe a mana'omia le fa'aogaina o ma'a tu'utū, e tatau ona fa'atūina le acid po'o le gel. Fa'afeso'ota'i ma'a i fa'amau fa'ailoga [– BAT +] (Ata 4g, itulau 6). Fa'aaogā maa e lua (2) 12VDC e feso'ota'i fa'asologa mo le fa'aogaina o le 24VDC (e aofia ai maa ta'ita'i). Fa'aaogā ma'a - Casil CL1270 (12V/7AH), CL12120 (12V/12AH), CL12400 (12V/40AH), CL12650 (12V/65AH) ma'a po'o UL iloa BAZR2 ma BAZR8 ma'a o se fua fa'atatau.

Ma'a ma AC Supervision galuega faatino (Ata. 4, itulau 8):
Fa'afeso'ota'i masini fa'ailoa fa'ailoga talafeagai i fa'ailoga ua fa'ailogaina [AC FAIL & BAT FAIL] (Fig. 4b, pg. 5) fa'atonu galuega faatino. Fa'aaoga le 22 AWG i le 18 AWG mo AC Fai & Low/Leai lipoti maa.
Ina ia tuai le lipoti mo le 6 itula, tipi le "AC Delay" osooso ma toe seti le malosiaga i le iunite (Ata 4f, itulau 6).
Tatala Fa'ailoga Afi (Ata 4c, itulau 6):
- Ina ia fa'agaoioi le Ta'otoga Afi, seti le DIP ki [Shutdown] i le tulaga ON.
- Ina ia tape le Alarm Afi Aveese seti le DIP ki [Shutdown] i le tulaga OFF.
Fa'atulagaina o tampe sui:
Mauga UL Lisi tamper ki (Altronix model TS112 pe tutusa) i le pito i luga o le pa. Fa'ase'e le tampfa'afeso'ota'i fa'amau i le pito o le pa puipui pe a ma le 2" mai le itu taumatau (Ata 6a, itulau 8). Fesootai tampfa'afeso'ota'i uaea i le avanoa e fa'aoga ai le Access Control Panel po'o le UL Listed reporting device talafeagai. Ina ia fa'agaoioi le fa'ailo fa'ailo tatala le faitoto'a o le pa.

Tausiga

E tatau ona su'eina le iunite ia le itiiti ifo ma le tasi i le tausaga mo le fa'agaioiga talafeagai e pei ona taua i lalo:

Galuega Faatino Voltagu Su'ega: I lalo o tulaga masani o uta o le DC voltage tatau ona siaki mo voltagu tulaga.
Su'ega ma'a: I lalo o tulaga masani o uta siaki ua uma le maa, siaki le voltage uma i le mea e fa'amau ai ma'a ma fa'amau fa'amau e fa'ailoga [– BAT +] ina ia mautinoa e leai se motu o uaea feso'ota'iga maa.

Fa'aaliga: Ole maualuga ole fa'atonuga ile taimi ole fa'a'ave'esea ole 3.6A.
Fa'aaliga: Ole fa'amoemoe ole ola ole maa e 5 tausaga; ae ui i lea, e fautuaina e sui maa i le 4 tausaga pe itiiti pe a manaʻomia

Ata 4 – AL1024ULXB2 Fa'atonu Fa'atonu

Diagnostics Taitaiina

AL1024ULXB2 – Komiti Fa'atonu

Mumu (DC)	lanu meamata (AC)	Tulaga Malosiaga
ON	ON	Tulaga masani o faʻagaioiga.
ON	TOTO	Ga'imau AC. O lo'o tu'uina atu le ma'a tu'u mai le paoa.
TOTO	ON	Leai se DC output.
TOTO	TOTO	Ga'imau AC. Ma'a ua fa'ate'a pe leai. Leai se DC output.

ACMS8 ma ACMS8CB Avanoa Pule Pule

LED	ON	TOTO
LED 1- LED 8 (Mula)	(s) fa'aliliuga fa'avevela le malosi.	Fa'aola (s) fa'auluuluga.
FACP	FACP fa'aoso fa'aosoina (tulaga fa'ailo).	FACP masani (tulaga e le o se fa'alaiga).
Fuafuaga lanu meamata 1-8	12VDC	–
Fuafuaga Mumu 1-8	24VDC	–

Fa'ailoga Fa'amau

AL1024ULXB2 – Komiti Fa'atonu

Terminal Legend	Galuega/Fa'amatalaga
L, N	Fa'afeso'ota'i le 115VAC i fa'amau nei: L i le vevela, N i le fa'aituau (Fig. 4a, itulau. 6).
+ DC -	Falegaosimea feso'ota'i ile ACMS8(CB) (Fig. 4d, itulau. 6).
AC Fai NC, C, NO	Fa'aaogaina e logoina ai le leiloa o le AC, egconnect i le masini fa'alogo po'o le fa'ailo. E masani ona fa'aola le ta'avale pe a iai le mana AC. Fa'amatalaga fa'afeso'ota'i 1A @ 28VDC. Ole AC po'o le brown out e lipotia ile 1 minute ole mea na tupu. Ina ia tuai le lipoti mo le 6 itula, tipi le "AC Delay" osooso ma toe seti le eletise i le iunite (Fig. 4f, itulau. 6).
Pe'a Fai NC, C, NO	Fa'aaoga e fa'ailoa ai le tulaga maualalo o le maa, fa'ata'ita'iga fa'afeso'ota'i i le fa'ailo. E masani ona fa'aola le ta'avale pe a iai le mana DC. Fa'amatalaga fa'afeso'ota'i 1A @ 28VDC. E lipoti atu se maa ua aveese i totonu ole 1 minute. Ua lipotia le toe so'oga maa i totonu ole 1 minute. Ma'a maualalo paepae: tusa 21VDC (Ata 4b, itulau 6).
– PAT +	So'oga tūtū maa. Ole maualuga ole tau ile taimi nei 3.6A (Fig. 4c, itulau. 6).

ACMS8 ma ACMS8CB Avanoa Pule Pule

Terminal Legend	Galuega/Fa'amatalaga
+ PWR1 –	Falegaosimea feso'ota'i ile AL1024ULXB2. Aua le fa'aogaina nei fa'amau.
+ PWR2 –	Falegaosimea feso'ota'i ile VR6 voltage fa'atonu. Aua le fa'aogaina nei fa'amau.
+ INP1 – e ala i + INP8 –	E valu (8) fa'atonu tuto'atasi Normally Open (NO), Normally Closed (NC), Open Collector Sink po'o Wet Input Triggers.
C, NC	FACP Dry NC galuega fa'amauina 1A/28VDC @ 0.6 Power Factor. Vasega 2 mana fa'agata. Faatasi ai ma le EOL JMP o loʻo faʻaogaina, o le a maua ai le 10k tetee i se tulaga masani.
GND, RST	FACP fa'aoga fa'apipi'i po'o le le fa'amauina. LEAI sao mago. Vasega 2 mana fa'agata. Fa'apuupuu mo le fa'aoga FACP e le fa'amauina po'o le toe setiina o le Latch FACP.
GND, EOL	EOL Vaavaaia FACP Input terminals mo polarity fesuia'i galuega FACP. Vasega 2 mana fa'agata.
– F, + F, – R, + R	FACP Fa'ailoga Si'o Fa'aulu ma fa'afo'i pito. Vasega 2 mana fa'agata.
Vaega 1 e ala i Galuega Faatino 8 LEAI, C, NC, COM	E valu (8) galuega faatino e mafai ona filifili tutoatasi [Fail-Safe (NC) po'o Fail-Secure (NO)] ma le valu (8) fa'atonuga tuto'atasi Fua "C" Relay.

Ata 6 – AL1024NKA8(D)

FAATUATUA: Fa'aaogā maa tu'u lua (2) 12VDC.

Taofi uaea fa'atapula'aina le malosi mai le fa'atapula'aina o le malosi. Fa'aoga le la'ititi ole 0.25” avanoa.

12AH O maa toe fa'aaogaina o ma'a sili ona tele e mafai ona ofi i totonu o lenei pa.
E tatau ona fa'aoga se pa'a pito i fafo o le ma'a UL-listed pe'a fa'aaoga maa 40AH po'o le 65AH.

Fa'ata'ita'iga masani

Fa'ata Fa'atasi

Ata 8 – Daisy-chaining tasi pe sili atu iunite ACMS8(CB). EOL Jumper [EOL JMP] e tatau ona fa'apipi'i ile tulaga EOL. Le fa'amauina.
Ata 9 – Daisy-chaining tasi pe sili atu iunite ACMS8(CB). EOL Jumper [EOL JMP] e tatau ona fa'apipi'i ile tulaga EOL. Latching Nofofua Toe setiina.
Ata 10 – Daisy filifili filifili se tasi pe sili atu ACMS8(CB) iunite. EOL Jumper [EOL JMP] e tatau ona fa'apipi'i ile tulaga EOL. Fa'amauina Fa'atonu Ta'ito'atasi.

Fa'ata Fa'atasi

Ata 11 – Fa'ailoga fa'aliliuga polarity mai le fa'asologa o fa'ailoga fa'ailo a le FACP (o lo'o fa'asino le polarity ile tulaga fa'ailo). Le fa'amauina
Ata 12 – Fa'asologa fa'afoliga polarity mai le fa'ailoga fa'ailoga a le FACP (o lo'o fa'asino le polarity ile tulaga fa'ailo). Fa'amauina

Ata 13 – E masani ona tapuni fa'aoso fa'aoso (E le fa'apipi'i).
Ata 14 – E masani ona tapunia mea fa'aoso (Latching).
Ata 15 – E masani ona tatala fa'aoso fa'aoso (E le fa'amauina)

Ata 16 – E masani ona tatala fa'aoso fa'aoso (Latching).

Fua Fa'amau (BC400)

15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm)

Altronix e le nafa mo soʻo se faʻaoga sese. 140 58th Street, Brooklyn, Niu Ioka 11220 ISA

telefoni: 718-567-8181
fax: 718-567-9056

webnofoaga: www.altronix.com
imeli: info@altronix.com
Malosiaga Faamaonia

Pepa / Punaoa

Altronix AL1024NKA8 Fa'asologa Lua Avanoa Avanoa Pule Pulea [pdf] Fa'atonu Taiala
AL1024NKA8, AL1024NKA8D, AL1024NKA8 Fa'asologa Lua Fa'atonu Avanoa Avanoa Pulea, Pule Fa'atonu Avanoa Fa'alua, Pule Fa'atonu, Pule Fa'atonu, Pule Fa'atonu, Pule Fa'atonu.

Fa'asinomaga

Tusi Taiala

Altronix AL1024NKA8 Fa'asologa Lua Avanoa Avanoa Pule Pulea

Ua umaview