Chii chinonzi Z-Wave?

Z-Wave ndiyo yepasirese isina waya protocol yekutaurirana muSmart Home. Izvi
mudziyo wakakodzera kushandiswa munharaunda yakataurwa muchikamu che Quickstart.

Z-Wave inovimbisa kutaurirana kwakavimbika nekusimbisa meseji yese (nzira mbiri
kutaurirana) uye ese mains powered node anogona kuita seanodzokorora mamwe ma node
(meshed network) kana iyo inogamuchira isiri yakananga isina waya renji ye
transmitter.

Ichi chishandiso uye chimwe nechimwe chakasimbiswa Z-Wave chishandiso chinogona kuva kushandiswa pamwe chete nezvimwe
yakasimbiswa Z-Wave mudziyo zvisinei nerudzi uye kwaakabva chero bedzi ari maviri akakodzera kune
zvakafanana frequency range.

Kana mudziyo unotsigira kukurukurirana kwakachengeteka ichataurirana nemimwe michina
yakachengeteka chero bedzi chigadziro ichi chinopa imwechete kana yakakwirira yehutano.
Zvikasadaro zvinongoerekana zvashanduka kuita yakaderera mwero wekuchengetedza kuchengetedza
kumashure kugarisana.

Kuti uwane rumwe ruzivo nezve Z-Wave tekinoroji, zvishandiso, machena mapepa nezvimwe ndapota tarisa
kune www.z-wave.info.

Product Description

Iyo STP328 ibhatiri rinoshandiswa pamadziro controller inokwanisa kudzora boiler actuator kuburikidza neZ-Wave isina waya yekubatanidza. Chishandiso chinogona kuita zvese seyekutanga controller kana sechipiri controller. Iyo yekudzora nekuchinja maitiro zvisinei haigone kusetwa isina waya asi nemabhatani ekudzora emuno chete. Chishandiso chine nguva dzakawandisa uye saka chinokwanisa kuita kunyangwe zvakaoma kudziya mamiriro.

Iyo STP328 inopihwa muzvikamu zviviri. Iyo actuator (SEC_SSR302) iyo yakaoma waya kune combi kana yakajairwa system boiler uye thermostat iyo inogona kushandiswa mune chero yakajairwa nharaunda yepamba mukati meyakajairwa 30 metres renji pasina kudiwa chero inodhura kana kukanganisa wiring.

Gadzirira Kuisa / Reset

Ndapota verenga bhuku rekushandisa usati waisa chigadzirwa.

Kuti ubatanidze (wedzera) mudziyo weZ-Wave kune network inofanira kunge iri mufekitari default
state. Ndokumbirawo muve nechokwadi chekuseta zvakare mudziyo mufekitari default. Unogona kuita izvi ne
kuita basa reKusabatanidzwa sezvinotsanangurwa pazasi mubhuku rekushandisa. Yese Z-Wave
controller inokwanisa kuita oparesheni iyi asi zvinokurudzirwa kushandisa yekutanga
mutongi weiyo yapfuura network kuti ave nechokwadi chekuti mudziyo wacho hauna kubatanidzwa nemazvo
kubva kune network iyi.

Installation

Thermostat

Iyo backplate yemudziyo inofanira kushandiswa sendiro yekuisa yekuisa madziro. Vhura iyo backplate nekusunungura screws iri pasi uye swing kuvhura control panel. Shandisa backplate sepateni uye womaka maburi ekuboorera, chera maburi uye woisa backplate. Iyo slots mubackplate inobhadhara chero kusarongeka kwezvigadziriso. Unganidzazve control panel nebackplate wobva waivharira munzvimbo yakavharwa.

Boiler Actuator

Kuiswa uye kubatana kweanogamuchira kunofanirwa kuitwa chete nemunhu ane hunyanzvi.

Kuti ubvise backplate kubva kune inogamuchira, sunungura maviri ekuchengetedza screws ari pasi; iyo backplate ikozvino inofanira kubviswa nyore nyore. Kana iyo backplate yabviswa kubva pakurongedzerwa, iva nechokwadi chekuti mugamuchiri avharwa zvakare kudzivirira kukuvadzwa kubva kuguruva, marara nezvimwe. Iyo backplate inofanirwa kusungirirwa neiyo wiring terminals kumusoro uye munzvimbo inobvumira kubviswa zvachose kweinenge. 50mm kutenderedza mugamuchiri.

Direct Wall Mounting

Iyo inogamuchira inofanirwa kunge iri padyo neiyo iripo magetsi mukati meiyo nyore wiring nzvimbo kune zvinhu zviri kuchinjwa. Ipa ndiro kumadziro munzvimbo iyo mugamuchiri anofanira kuiswa, uchiyeuka kuti backplate inokodzera kuruboshwe rworuboshwe rwemugamuchiri. Maka nzvimbo dzekugadzirisa kuburikidza nezvinotsvedza mubackplate, bhora uye plug madziro, wozochengetedza ndiro panzvimbo. Iyo slots mubackplate inobhadhara chero kusarongeka kwezvigadziriso.

Wiring Box Mounting

Iyo inogamuchira backplate inogona kuiswa yakananga pane imwechete gang simbi flush wiring box inoenderana neBS4662 uchishandisa maviri M3.5 screws. Iyo inogamuchira inokodzera kukwidziridzwa pane yakati sandara chete. Haifanirwe kuiswa panzvimbo yesimbi yakafukunurwa.

Kubatanidza magetsi

Zvese zvinodiwa zvekubatanidza magetsi zvinofanirwa kuitwa. Flush wiring inogona kupinda kubva kumashure kuburikidza neaperture iri mubackplate. Surface wiring inogona kupinda chete kubva pasi peinogamuchira uye inofanira kunge yakachengeteka clamped. Iwo mains ekupa materminals anoitirwa kuti abatanidzwe kune inopihwa nenzira yakagadziriswa wiring. Iyo inogamuchira ine mains powered uye inoda 3 amp fused spur. Iwo akakurudzirwa tambo saizi i1.0mm2 kana 1.5mm2.

Iyo inogamuchira yakapetwa kaviri insulated uye haidi kubatanidza kwepasi kunyangwe chivharo chekubatanidza pasi chinopihwa pandiro yekumashure yekumisa chero tambo yepasi conductor. Kuenderera mberi kwepasi kunofanirwa kuchengetedzwa uye ese akashama pasi conductor anofanirwa kuve nemaoko. Ita shuwa kuti hapana maconductor anosiiwa achibuda kunze kwepakati nzvimbo yakavharirwa nebackplate.

Yemukati Wiring Dhiyagiramu

Iyo SSR302 ine yakabatana yekubatanidza inoita kuti ive yakakodzera kune mains voltage application chete. Hapana kuwedzera kubatanidza kunodiwa pakati pematerminals.

Kugadzirisa Receiver

Kana iyo wiring yepamusoro yakashandiswa, bvisa kugogodza / isa kubva pazasi thermostat kuti igamuchire. Gadzirisa inogamuchira kubackplate, ita shuwa kuti mabhegi ari kubackplate anobata pamwe neanotsvedza pane anogamuchira. Svetedza pasi peinogamuchira munzvimbo uchiona kuti mapini ekubatanidza ari kuseri kweyuniti anowanikwa mukati meiyo terminal slots mubackplate.

Yambiro: IYOLATE MAINS SUPPLY USATI WATANGA KUISA!

Kubatanidzwa/Kusabatanidzwa

Pafekitori default mudziyo hausi weZ-Wave network. Chishandiso chinoda
kuva yakawedzerwa kune iripo isina waya network kutaurirana nemidziyo yetiweki iyi.
Iyi nzira inodaidzwa Kubatanidzwa.

Midziyo inogona zvakare kubviswa kubva kunetiweki. Iyi nzira inodaidzwa Kusabatanidzwa.
Maitiro ese ari maviri anotangwa neyekutanga controller yeZ-Wave network. Izvi
controller inoshandurwa kuita yekusabatanidzwa inoenderana inclusion mode. Kubatanidzwa uye Kusabatanidzwa ndiko
obva aita kuita yakakosha yemanyorero chiito pamudziyo.

Kubatanidzwa

YeKusanganisirwa uye Kusabatanidzwa dzvanya uye bata mabhatani ese machena pamudziyo kusvika iyo LED yatanga kupenya. (girinhi -> Kubatanidzwa, tsvuku -> Kusabatanidzwa)

Kusabatanidzwa

YeKusanganisirwa uye Kusabatanidzwa dzvanya uye bata mabhatani ese machena pamudziyo kusvika iyo LED yatanga kupenya. (girinhi -> Kubatanidzwa, tsvuku -> Kusabatanidzwa)

Kushandiswa Kwechigadzirwa

Thermostat

Chikamu 1 - Zuva nezuva kushanda

Iyo Thermostat yakagadzirwa kuti ive nyore kushandisa thermostat, inoda kushoma kupindira kwemushandisi ine pre-yakagadzirirwa kudziyisa pro.file. Kugadzirisa tembiricha kuri nyore kunogona kuitwa nyore nekushandisa mabhatani "+" uye "-". Zviedza zvechiratidzo zvinobata kune chero zvigadziriso zvemushandisi zvenguva pfupi, nezviratidzo zve LED zvinoshanda nenzira inotevera; "Kudziya" kunoratidzwa nemwenje miviri mitsvuku uye "Kutonhorera" inoratidzwa nechiedza chimwe chebhuruu. Bhatani repakati rakanyorwa kuti "Kudziya / Kutonhorera" rinokutendera iwe kuti uchinje pakati peinodziya uye inotonhorera marongero.

Power Down Mode

Panguva yekushanda kwakajairika Thermostat ichapinda muPower Down Mode, uku kukwidziridza hupenyu hwemabhatiri e3 x AA akaiswa. Kushanda kwakajairika kunoenderera mberi panguva iyi, uye kupisa kunenge kusina kukanganiswa. Mhedzisiro yePower Down Mode ichareva kuti zviratidzo zve LED hazvizoonekwe uye LCD haizovhenekerwe, kunyangwe tembiricha ye "Warm" kana "Cool" icharatidzwa. Kuti "muke" iyo AS2-RF dzvanya bhatani re "Kudziya / Kutonhorera" kwemasekonzi mashanu, izvi zvinozovhenekera zvese maLED neLCD kuratidza kwenguva. Chero kugadzirisa kunogona kuitwa, iyo Power Down Mode ichatanga zvakare anenge masekonzi masere mushure mekudzvanya bhatani rekupedzisira.

Kugadziriswa Kwekudziya uye Kunotonhorera

Iyo Inodziya uye Inotonhorera inonangwa tembiricha marongero paThermostat inogadziriswa zvizere. Kuti uchinje tembiricha yaunonangwa, zvinofanirwa kutanga wadzvanya bhatani repakati kuti uunze "Kudziya" kana "Kutonhorera" kuseta (inoratidzwa neiyo tsvuku kana yebhuruu LED zviratidzo). Nekushandisa makiyi ekumusoro/pasi pasi pechivharo tembiricha Inodziya/Kutonhorera inogona kuwedzerwa kana kudzikiswa kune inodiwa tembiricha. PLEASE ONA - hazvigoneke kuseta inodziya kuseta kusvika pazasi peiyo inotonhorera yekuseta kana zvinopesana. Kana tembiricha nyowani yaiswa mune Inodziya kana Kutonhorera kuseta iyo Thermostat icharamba ichishandisa iyi kuseta kusvika kunotevera kugadziridzwa kwebhuku.

Frost Protection

Bhatani rebhuruu riri pasi pechifukidziro richatanga nzira yekudzivirira chando, kana ikadzvanywa izwi rekuti "STANDBY" richaonekwa pachiratidziro, iyo thermostat yakagadziridzwa nechando chekudzivirira tembiricha ye7C, izvi zvinogona kugadziriswa nekushandisa kumusoro uye. mabhatani emiseve pasi. Minimum setting 5C. Hazvibviri kuisa tembiricha yekudzivirira chando pamusoro penzvimbo inotonhorera.

Chikamu 2 - Programming Mode

Iyo Thermostat yakagadzirirwa kupindira kushoma kwevashandisi, zvisinei kana paine shanduko kumapurogiramu aripo akadikanwa ndapota tinya bhatani 6 uye 8 panguva imwe chete kuti upinde muchirongwa chekugadzirisa, izvi zvinokutendera kuti:

• Tarisa ikozvino nguva / zuva / gore
• Tarisa ikozvino profile
• Seta itsva pre-set profile or
• Seta mushandisi anotsanangurwa profile

PLEASE CHERECHEDZA: Kana wapedza chero zvigadziriso zviri pamusoro, ndapota ita shuwa kuti wabuda muchirongwa chekugadzira nekudzvanya mabhatani 6 uye 8 panguva imwe chete.

Nguva uye Date Check

Iyo Thermostat ine yakavakirwa otomatiki wachi kugadzirisa yeBST uye GMT nguva shanduko uye yakagadziridzwa nenguva iripo uye zuva panguva yekugadzira. Hapana shanduko inofanirwa kudikanwa kune iyo nguva uye zuva, zvisinei kana chero shanduko ichidikanwa ndapota tarisa kune matanho ari pazasi.

• Vhura Kavha
• Pinda programming mode nekudzvanya mabhatani 6 uye 8
• Dzvanya TIME
• Dzvanya SET
• MINUTE inopenya. Rongedza uchishandisa UP/DOWN mabhatani. Dzvanya SET
• HOUR inopenya. Rongedza uchishandisa UP/DOWN mabhatani. Dzvanya SET
• DATE rinopenya. Rongedza uchishandisa UP/DOWN mabhatani. Dzvanya SET
• MWEDZI unopenya. Rongedza uchishandisa UP/DOWN mabhatani. Dzvanya SET
• GORE rinopenya. Rongedza uchishandisa UP/DOWN mabhatani. Dzvanya SET
• Dhinda EXIT
• Buda purogiramu yekugadzira nekudzvanya mabhatani 6 uye 8

Kuisa Heating Profiles

Iyo Thermostat ine sarudzo yeshanu preset uye mushandisi mumwe anotsanangurwa profile sarudzo, imwe yeiyi ichave yakaiswa neMugadziri. Kutarisira kunofanira kutorwa kuve nechokwadi cheprofile inosarudzwa inoenderana nemararamiro ako zvakanyanya. Kana pasina imwe yepreset profiles kusangana nezvinodiwa zvako zvinokwanisika kuseta mushandisi anotsanangurwa profile.

• Vhura Kavha
• Pinda porgramming mode nekudzvanya mabhatani 6 uye 8
• Dzvanya PROG
• Dzvanya SET
• Sarudza inodiwa profile nekushandisa mabhatani eUP/DOWN
• Dzvanya SET. To review preset profiles 1 kusvika 5 dzvanya UP bhatani (7) kakawanda
• Dhinda EXIT
• Buda purogiramu yekugadzira nekudzvanya mabhatani 6 uye 8

Kupisa Profiles

Iyo Thermostat ine matanhatu ekudziya profiles, zvishanu zvakagadziriswa uye imwe inogadziriswa. Profile "IMWE" yakasetwa seyakagadzika uye yakatsanangurwa pazasi. Panguva yekuisa kupisa profile inofanira kunge yakaiswa kuti ienderane nezvinodiwa zvako:

Profiles one kusvika kushanu ane nguva dzakatarwa, hapana shanduko kuNguva Inodziya / Inotonhorera inogona kuitwa, kana zvichidikanwa kuita chero shanduko ipapo profile matanhatu anofanira kushandiswa. Profile nhanhatu ichakubvumidza iwe kumisikidza profile kune zvaunoda chaizvo.

Mushandisi Anotsanangurwa - 7 Day Programming

Profile 6 ichakubvumidza iwe kumisikidza profile kune zvaunoda chaizvo. Nekushandisa kuyerera kwechati pazasi iwe unogona kugadzirisa Iyo Inodziya / Inotonhorera yenguva nguva sezvinodiwa. Kana imwe chete kana mbiri nguva yeKudziya/Kutonhorera inodiwa pane chero zuva isa nguva zvinoenderana uye isa yasara Inodziya uye Inotonhorera nguva dzekutanga kuti dzinyatsofanana. Izvi zvinobvisa 2nd kana 3rd Kudziya/Kutonhorera nguva zvachose pazuva rine chekuita. Nguva dzisina kushandiswa dzicharatidzwa nenhevedzano yemadhidhi pane zvigadziriso skrini. Dzvanya SET uye zuva rinotevera uye SET inooneka muchiratidziro. Dzvanya SET kuti ugadzirise marongero emazuva anotevera kana EXIT kuti udzokere kumenu huru. Kuti uite izvi tinya SET kusvika zuva rinotevera uye SET inoonekwa muchiratidziro. Nguva dzisina kushandiswa dzicharatidzwa nenhevedzano yemadhidhi pane yekumisikidza skrini. Kana imwe kana mbiri dzakasetwa uye uchishuvira kudzoka kunhambo nhatu mumaawa makumi maviri nemana wodzvanya museve wekumusoro kana madheshi aoneka mushure mekupedzisira Kutonhorera kunounza kudzosa kwakavanda Kudziya/Kutonhorera marongero.

• Vhura Kavha
• Pinda porgramming mode nekudzvanya mabhatani 6 uye 8
• Dzvanya PROG
• Dzvanya SET
• Sarudza PROFILE SIX nekushandisa UP/DOWN mabhatani uye tinya SET
• Gadzirisa iyo WARM yekutanga nguva nekushandisa UP/DOWN mabhatani uye nekusimbisa neSET bhatani
• Gadzirisa iyo COOL yekutanga nguva nekushandisa UP/DOWN mabhatani uye nekusimbisa neSET bhatani
• Dzokorora kwePeriods 2 uye 3 (kana kana zvisiri kudikanwa enzanisa yasara Inodziya uye Inotonhorera nguva kudzima uye kudzvanya SET - ona pamusoro)
• SET inoratidzwa pachiratidziro 1. Kuti uenderere mberi nehurongwa kusvika kuzuva rinotevera dzvanya SET uye enda ku "A" 2. Kuti ukope marongero achinjwa kuzuva rinotevera dzvanya bhatani DOWN uye enda ku "C" 3. Kuti upedze kuronga enda kuna “D”
• Dzvanya COPY uye dzokorora zuva rega rega kuti akodzwe
• Kana wapedza dzvanya bhatani DOWN uye enda ku "B"
• Dzvanya EXIT kaviri uye buda purogiramu yekugadzira nekudzvanya mabhatani 6 uye 8

Boiler Actuator

Iyo unit inotsigira maviri static ekupedzisira mapoinzi ematanho maviri.

Kudzvanya Top White bhatani re 1 sekondi ichapa "end point capability report" yechiteshi 1. Kudzvanya bhatani rePazasi White kwesekondi 1 kuchaburitsa "end point capability report" yechiteshi 2. Uyezve michina inopinda yekudzidza mode ye1. chepiri. Izvi zvinobatsira kana uchibatanidza / kusabatanidza chishandiso neboka rekutonga kana kungoona chishandiso uye makirasi ekuraira anotsigirwa. Izvi zvinogona kuitwa chero nguva asi hazvizopi chero chiratidzo kune anoshanda

Nhepfenyuro nenzira iyi yakaitwa kuti itsigire kubatana kwechiteshi chine mutongi webato rechitatu anotsigira Multi-Channel Command Class.

Node Information Frame

Iyo Node Information Frame (NIF) ibhizinesi kadhi remuchina weZ-Wave. Rine
ruzivo nezve rudzi rwechigadzirwa uye kugona kwehunyanzvi. Kubatanidzwa uye
kusabatanidzwa kwechishandiso kunosimbiswa nekutumira Node Ruzivo Frame.
Padivi peizvi zvinogona kudikanwa kune mamwe mabasa etiweki kutumira Node
Information Frame. Kuburitsa NIF ita zvinotevera:

Kudzvanya nekubata mabhatani maviri machena kwesekondi 1 kuchaita kuti mudziyo uburitse Node Information Frame.

Kukurumidza dambudziko kupfura

Heano mashoma mazano ekuisa network kana zvinhu zvikasashanda sezvaitarisirwa.

1. Ita shuwa kuti mudziyo uri mufekitori reset mamiriro usati wasanganisira. Mukupokana usabvisa pamberi sanganisira.
2. Kana kusanganisirwa kuchiri kutadza, tarisa kana zvese zvishandiso zvinoshandisa ma frequency akafanana.
3. Bvisa zvese zvakafa kubva kumasonganiro. Zvikasadaro uchaona kunonoka kwakanyanya.
4. Usamboshandisa bhatiri midziyo yekurara isina yepakati controller.
5. Usavhote FLIRS zvishandiso.
6. Ita shuwa kuti une yakakwana mains powered mudziyo kuti ubatsirwe kubva kune meshing

Kushamwaridzana - imwe mudziyo inodzora imwe mudziyo

Z-Wave zvishandiso zvinodzora zvimwe Z-Wave zvishandiso. Ukama pakati pemudziyo mumwe
kudzora mumwe mudziyo kunonzi kushamwaridzana. Kuti udzore zvakasiyana
mudziyo, mudziyo unodzora unofanirwa kuchengetedza runyoro rwemidziyo inogashira
kudzora mirairo. Aya mazita anonzi mapoka ekubatana uye anogara aripo
zvine chekuita nezvimwe zviitiko (semuenzaniso bhatani rakadzvanywa, sensor trigger, ...). Zvikazo
chiitiko chinoitika ese maturusi akachengetwa muboka rekubatana achaita
gamuchira imwechete isina waya yekuraira isina waya, kazhinji iyo 'Basic Set' Command.

Mapoka eMasangano:

Nhamba YebokaMaximum NodesDescription

1

5

Zvishandiso zvinodzorwa neakavhurika/kuvhara zviitiko

Technical Data

Dimensions	0.0900000×0.2420000×0.0340000 mm
Kurema	470 gr
EAN	5015914212017
Device Type	Routing Binary Sensor
Kirasi Yekushandisa Yechigadzirwa	Binary Sensor
Specific Device Kirasi	Routing Binary Sensor
Firmware Shanduro	01.03
Z-Wave Vhezheni	02.40
Chitupa ID	ZC07120001
Z-Wave Chigadzirwa Id	0086.0002.0004
Frequency	Europe - 868,4 Mhz
Maximum transmission simba	5 mW

Inotsigirwa Command Classes

• Basic
• Bhatiri
• Muka
• Kushamwaridzana
• Version
• Sensor Binary
• Alarm
• Manufacturer Specific

Controlled Command Classes

• Basic
• Alarm

Tsanangudzo yeZ-Wave chaiyo mazwi

• Controller - iri Z-Wave mudziyo une kugona kubata network.
  Ma controller anowanzo magedhi, Remote Controls kana bhatiri rinoshandiswa madziro controller.
• Muranda - iri Z-Wave chishandiso chisina kugona kubata network.
  Varanda vanogona kunge vari masensa, actuators uye kunyange kure kure.
• Primary Controller - ndiye murongi wepakati wetiweki. Zvinofanira kuva
  controller. Panogona kuve nemutongi mumwe chete wekutanga muZ-Wave network.
• Kubatanidzwa - ndiyo maitiro ekuwedzera michina mitsva yeZ-Wave mune network.
• Kusabatanidzwa - ndiyo maitiro ekubvisa Z-Wave zvishandiso kubva kunetiweki.
• Kushamwaridzana - hukama hwekutonga pakati pemudziyo unodzora uye
  mudziyo unodzorwa.
• Wakeup Chiziviso -imeseji yakakosha isina waya yakapihwa neZ-Wave
  mudziyo wekuzivisa unokwanisa kutaura.
• Node Information Frame -imeseji yakakosha isina waya inoburitswa nea
  Z-Wave mudziyo kuzivisa kugona kwayo uye mabasa.