iSMACONTROLLI SFAR-S-16RO Modbus Input And Output Module
KUTAURA
| KUTAURA | ||
| Magetsi | Voltage | 10-38 V DC; 10-28 V AC |
| Simba rekushandisa | 4,8 W @ 24 V DC 7 VA @ 24 V AC | |
| Relay zvinobuda | 16x Relay zvabuda | |
| Resistive mutoro AC1: 3 A @ 230 V AC kana 3 A @ 30 V DC | ||
| Inductive mutoro AC3. 75 VA @ 230 V AC kana 30 W @ 30 V DC | ||
| Bata zvinhu AgSnO2 | ||
| Interface | RS485, anosvika zana nemakumi maviri nemasere zvishandiso mubhazi | |
| Bhaudrate | Kubva 2400 kusvika 115200 bps | |
| Ingress kudzivirira | IP40 - yekuisa mukati memukati | |
| Tembiricha | Kushanda -10°C - +50°C; Kuchengetedza -40°C - +85°C | |
| Hunyoro hunyoro | 5 kusvika 95% RH (pasina condensation) | |
| Connectors | Hukuru 2.5 mm2 | |
| Dimension | 119,1 mm x 101 mm x 22,6 mm | |
| Mounting | DIN njanji inokwira (DIN EN 50022) | |
| Zvinhu zveimba | Plastiki, inodzima PC/ABS | |
TOP PANEL 
RELAY OUTPUTS 
COMUNICATION
MAGETSI
YAMBIRO
- Cherechedza, wiring isiriyo yechigadzirwa ichi inogona kukuvadza uye kutungamirira kune dzimwe njodzi. Ita shuwa kuti chigadzirwa chave nemawaya zvakanaka usati wabatidza magetsi.
- Usati waita waya, kana kubvisa / kusimudza chigadzirwa, iva nechokwadi chekudzima simba. Kutadza kuzviita kunogona kukonzera kuvhunduka kwemagetsi.
- Usabate mativi anochajiswa nemagetsi sematerminals emagetsi. Kuita izvi kunogona kukonzera kuvhunduka kwemagetsi.
- Usabvisa chigadzirwa. Kuita izvi kunogona kukonzera kuvhunduka kwemagetsi kana kuti kushanda kusina kunaka.
- Shandisa chigadzirwa mukati memaitiro ekushanda anokurudzirwa mune yakatarwa (tembiricha, humidity, voltage, kuvhunduka, kukwira kutungamira, mamiriro ekunze nezvimwe). Kutadza kuita izvi kunogona kukonzera moto kana kutadza kushanda zvakanaka.
- Simbisa waya kune terminal. Kusasimba zvakakwana kwewaya kuchiteshi kunogona kukonzera moto.
TERMINALS OF THE DEVICE 
Registered access
| Modbus | Dec | Hex | Register Zita | Access | Tsanangudzo |
| 30001 | 0 | 0x00 | Version/Type | Verenga | Version uye mhando ye |
| 30002 | 1 | 0x01 | Swichi | Verenga | Inochinja nyika |
| 40003 | 2 | 0x02 | Baud rate | Verenga & Nyora | RS485 baud chiyero |
| 40004 | 3 | 0x03 | Misa Bits & Data Bits | Verenga & Nyora | Hapana chekumira bits & data |
| 40005 | 4 | 0x04 | Parity | Verenga & Nyora | Parity zvishoma |
| 40006 | 5 | 0x05 | Mhinduro Kunonoka | Verenga & Nyora | Mhinduro kunonoka muna ms |
| 40007 | 6 | 0x06 | Modbus Mode | Verenga & Nyora | Modbus modhi (ASCII kana |
| 40009 | 8 | 0x08 | Watchdog | Verenga & Nyora | Watchdog |
| 40013 | 12 | 0x0C | Default Output State | Verenga & Nyora | Default inobuda mamiriro |
|
40033 |
32 |
0x20 |
Mapaketi akagamuchirwa LSR (Isina Kukosha Reg.) |
Verenga & Nyora |
Hapana emapaketi akagamuchirwa |
|
40034 |
33 |
0x21 |
Yakagamuchira mapaketi MSR (Yakanyanya Yakakosha Reg.) |
Verenga & Nyora |
|
| 40035 | 34 | 0x22 | Mapaketi asina kururama LSR | Verenga & Nyora | Hapana emapaketi akagamuchirwa ane kukanganisa |
| 40036 | 35 | 0x23 | Mapaketi asina kururama MSR | Verenga & Nyora | |
| 40037 | 36 | 0x24 | Akatumira mapaketi LSR | Verenga & Nyora |
Kwete yemapaketi akatumirwa |
| 40038 | 37 | 0x25 | Akatumira mapaketi MSR | Verenga & Nyora | |
| 40052 | 51 | 0x33 | Outputs | Verenga & Nyora | Output state |
INSTALLATION GUIDELINE
- Ndapota verenga rairo usati washandisa kana kushandisa mudziyo. Kana paine mibvunzo mushure mekuverenga gwaro iri, ndapota taura neSMA CONTROLLI Support Team
- (support@ismacontrolli.com).
- Usati waisa waya kana kubvisa / kusimudza chigadzirwa, ita shuwa yekudzima magetsi. Kutadza kuita izvi kunogona kukonzera kurohwa nemagetsi.
- Wiring isina kunaka yechigadzirwa inogona kuikuvadza uye inotungamirira kune dzimwe njodzi. Ita shuwa kuti chigadzirwa chave nemawaya zvakanaka usati wabatidza magetsi.
- Usabate mativi anochajiswa nemagetsi sematerminals emagetsi. Kuita izvi kunogona kukonzera kuvhunduka kwemagetsi.
- Usabvisa chigadzirwa. Kuita izvi kunogona kukonzera kuvhunduka kwemagetsi kana kutadza kushanda zvakanaka.
- Shandisa chigadzirwa chete mukati memaitiro ekushanda anokurudzirwa mune yakatarwa (tembiricha, humidity, voltage, kuvhunduka, kukwira kutungamira, mamiriro ekunze, nezvimwewo). Kutadza kuita izvi kunogona kukonzera moto kana kutadza kushanda zvakanaka.
- Simbisa waya kune terminal. Kutadza kuzviita kungakonzera moto.
- Regedza kuisa chigadzirwa padhuze nemagetsi ane simba guru midziyo uye tambo, inductive mitoro, uye switching michina. Kuva pedyo kwezvinhu zvakadaro kunogona kukonzera kukanganisa kusingadzoreki, zvichiita kuti kusagadzikana kushanda kwechigadzirwa.
- Kurongeka kwakakodzera kwesimba uye chiratidzo cabling kunokanganisa kushanda kweiyo yese control system. Dzivisa kuisa simba uye chiratidzo wiring mumatireyi etambo akafanana. Inogona kukonzera kukanganisa mukutariswa uye kutonga zviratidzo.
- Inokurudzirwa kusimba ma controller/modules ane AC/DC vatengesi vemagetsi. Ivo vanopa zvirinani uye zvakatsiga insulation zvemidziyo zvichienzaniswa ne AC/AC shanduri masisitimu, ayo anofambisa zvinokanganisa uye zvenguva pfupi zviitiko senge masurges uye kuputika kumidziyo. Ivo zvakare vanoparadzanisa zvigadzirwa kubva kune inductive phenomena kubva kune mamwe ma transformer uye mitoro.
- Masisitimu ekupa magetsi echigadzirwa anofanirwa kuchengetedzwa nemidziyo yekunze inodzikamisa overvoltage uye mhedzisiro yemheni inobuda.
- Dzivisa kupa simba chigadzirwa nemidziyo yayo inodzorwa/inotariswa, kunyanya simba repamusoro uye inductive mitoro, kubva kune imwechete magetsi sosi. Zvishandiso zvemagetsi kubva kune imwe simba sosi zvinokonzeresa njodzi yekuunza kukanganisa kubva kune mitoro kuenda kune yekudzora michina.
- Kana AC/AC transformer ikashandiswa kugovera zvigadziriso zvekushandisa, zvinokurudzirwa zvakanyanya kushandisa inodarika zana VA Kirasi 100 transformer kudzivirira zvisingadiwe inductive mhedzisiro, iyo ine njodzi kumidziyo.
- Kureba kwekutarisa uye kutonga mitsara kunogona kukonzera zvishwe zvine chekuita neiyo yakagovaniswa magetsi, zvichikonzera kukanganisa mukushanda kwemidziyo, kusanganisira kutaurirana kwekunze. Inokurudzirwa kushandisa galvanic separators.
- Kuchengetedza masaini uye mitsara yekutaurirana kubva kune ekunze kukanganiswa kwemagetsi, shandisa tambo dzakadzivirirwa zvakanaka uye ferrite bead.
- Kuchinja dhijitari inoburitsa relays yehombe (inodarika yakatarwa) inductive mitoro inogona kukonzera kukanganiswa pulses kune zvemagetsi zvakaiswa mukati mechigadzirwa. Nokudaro, zvinokurudzirwa kushandisa kunze relays / contactors, nezvimwewo kushandura mitoro yakadaro. Iko kushandiswa kwezvidzori zvine triac zvinobuda zvakare kunoganhura zvakafanana overvoltage phenomena.
- Zviitiko zvakawanda zvekuvhiringidzika uye kuwandisatage in control system inogadzirwa nekuchinja, inductive mitoro inopihwa nealternating mains vol.tage (AC 120/230 V). Kana vasina maseketi akakodzera akavakirwa-mukati ekuderedza ruzha, zvinokurudzirwa kushandisa maseketi ekunze akadai sema snubbers, varistors, kana kudzivirira diode kudzikamisa izvi.
- Kuiswa kwemagetsi kwechigadzirwa ichi kunofanira kuitwa maererano nemitemo yenyika ye wiring uye inoenderana nemitemo yemunharaunda.
- iSMA CONTROLLI SpA – Via Carlo Levi 52, 16010 Sant'Olcese (GE) – Italy
- support@ismacontrolli.com
- www.ismacontrolli.com
- Installation Guideline| 1st Nyaya rev. 1 | 05/2022
Zvinyorwa / Zvishandiso
 |
iSMACONTROLLI SFAR-S-16RO Modbus Input And Output Module [pdf] Bhuku reMirayiridzo SFAR-S-16RO Modbus Input And Output Module, SFAR-S-16RO, Modbus Input And Output Module, Input And Output Module, Output Module, Module |
