Autonics TCN4 SERIES Dual Indicator Temperature Controller

Product Information

Iyo Autonics Dual Indicator Temperature Controller chikamu cheTCN4 Series uye inobata-chinja inogadziriswa, mbiri-yekuratidza mhando controller. Iyo inokwanisa kudzora uye kutarisa tembiricha nekururama kukuru.

Features

• Dual kuratidzwa kuitira nyore kutarisa tembiricha.
• Bata switch yekuseta kuti zvive nyore kugadzirisa.
• Relay yekubata uye Solid State Relay (SSR) yekubuda modes iripo.
• Ma alarm akawanda anobuda kuitira kuchengetedzwa kwakawedzerwa.
• Inowanikwa mune dzakasiyana siyana magetsi ekupa.
• Compact size yekuisa nyore.

product Specifications

• Wiring Method: Bolt (Hapana mucherechedzo)
• Kudzora Kubuda: Relay Contact + SSR Drive Output
• Simba rekupa: 24VAC 50/60Hz, 24-48VDC kana 100-240VAC 50/60Hz
• Alarm Outputs: 2 (Alarm1 + Alarm2)
• Digit Setting Type: 4 (9999 - 4 digit)
• Rudzi rweKuratidza: Dual
• Chinhu: Temperature Controller
• Saizi: S (Idiki), M (Yepakati), H (Yakakwirira), L (Yakaderera)

Mirayiridzo Yekushandiswa Kwechigadzirwa

1. Usati washandisa Autonics Dual Indicator Temperature Controller, verenga pfungwa dzekuchengetedza dzinotaurwa mubhuku rekuraira nokungwarira.
2. Isa controller pane mudziyo wepaneru kuti uone kushandiswa kwakachengeteka uye kudzivirira kuvhunduka kwemagetsi kana njodzi dzemoto.
3. Ita shuwa kuti sosi yemagetsi yadzimwa usati wabatanidza, kugadzirisa, kana kuongorora chikwata. Kutadza kuita izvi kunogona kukonzera kuvhunduka kwemagetsi kana njodzi dzemoto.
4. Tarisa 'MaConnections' usati waisa waya kuti udzivise chero njodzi, iyo inogona kukonzera njodzi yemoto.
5. Shandisa AWG 20(0.50mm2) kana tambo yakakora kana uchibatanidza powerinput uye relay inobuda. Shandisa tambo yeAWG 28~16 uye simbisa siruuru ine torque inosimbisa ye 0.74~0.90Nm paunenge uchibatanidza tambo yekupinza uye yekutaurirana. Kutadza kuita izvi kunogona kukonzera moto kana kusashanda zvakanaka nekuda kwekutadza kubata.
6. Shandisa Autonics Dual Indicator Temperature Controller mukati mezvakatemerwa zvakatemerwa kudzivirira moto kana kukuvara kwechigadzirwa.
7. Shandisa jira rakaoma kuti uchenese chikwata; usamboshandisa mvura kana organic solvents. Kutadza kuita izvi kunogona kukonzera kuvhunduka kwemagetsi kana njodzi dzemoto.
8. Regedza kushandisa yuniti munzvimbo dzine gasi rinobvira/inoputika/inoparadza, mwando, zuva rakananga, kupisa kunopenya, kuzunguzika, kukanganiswa, kana munyu. Kutadza kuita izvi kunogona kukonzera moto kana kuputika.
9. Chengetedza simbi machipisi, huruva, uye waya zvisaririra kubva pakuyerera kupinda muyuniti kudzivirira moto kana kukuvara kwechigadzirwa.
10. Tarisa kune ruzivo rwekuodha rwunotaurwa mubhuku rekuraira usati waraira Autonics Dual Indicator Temperature Controller.

Mifungo Yekuchengetedza

• Ndokumbira utarise zvese zvekuchengetedza kuchengetedzwa uye kwakachengeteka kwechigadzirwa mashandiro kudzivirira njodzi.
• Mafungiro ekuchengetedza akaiswa muzvikamu zvinotevera.
  • Yambiro Kutadza kutevedzera mirairo iyi kunogona kukonzera kukuvara kwakanyanya kana kufa.
  • Chenjero Kutadza kutevedzera mirairo iyi kunogona kukonzera kukuvara kwemunhu kana kukuvara kwechigadzirwa.
• Zviratidzo zvinoshandiswa pachigadzirwa uye bhuku rekuraira zvinomiririra chiratidzo chinotevera chinomiririra kungwarira nekuda kwemamiriro ezvinhu anogona kuitika njodzi.

Yambiro

1. Chishandiso chinotadza-kuchengetedza chinofanirwa kuiswa kana uchishandisa iyo unit ine muchina inogona kukonzera kukuvara kwakanyanya kana kurasikirwa kwakanyanya kwehupfumi. (semuenzaniso kudzora simba renyukireya, midziyo yekurapa, ngarava, mota, njanji, ndege, midziyo yekupisa, midziyo yekuchengetedza, midziyo yekudzivirira kuparwa kwemhosva/njodzi, nezvimwewo)
   Kutadza kutevedzera murairo uyu kunogona kukonzera moto, kukuvara kwemunhu, kana kurasikirwa kwehupfumi.
2. Isa pane mudziyo wekushandisa kuti ushandise. Kutadza kutevedzera murairo uyu kunogona kukonzera kuvhunduka kwemagetsi kana moto.
3. Usabatanidze, kugadzirisa, kana kuongorora iyo unit paunenge wakabatana kune sosi yemagetsi. Kutadza kutevedzera murairo uyu kunogona kukonzera kuvhunduka kwemagetsi kana moto.
4. Tarisa 'Kubatanidza' usati wiring. Kutadza kutevera kuraira uku kunogona kukonzera moto.
5. Usabvisa kana kushandura iyo unit. Kutadza kutevedzera murairo uyu kunogona kukonzera kuvhunduka kwemagetsi kana moto.

Kuchenjerera

1. Paunenge uchibatanidza magetsi ekuisa uye relay kubuda, shandisa AWG 20 (0.50mm2) tambo kana pamusoro uye simbisa iyo terminal screw ine inosimbisa torque ye 0.74 ~ 0.90Nm Paunenge uchibatanidza iyo sensor yekupinza uye yekutaurirana tambo isina yakatsaurirwa tambo, shandisa AWG 28 ~ 16 tambo uye simbisa siruu yemugumo netorque inosimbisa ye 0.74~0.90Nm Kutadza kutevedzera murairo uyu kunogona kukonzera moto kana kusashanda zvakanaka nekuda kwekutadza kubata.
2. Shandisa chikwata mukati mezvakatemerwa zvakatemwa. Kutadza kutevedzera murairo uyu kunogona kukonzera moto kana kukuvara kwechigadzirwa. 3. Shandisa jira rakaoma kuti uchenese chikwata, uye usashandise mvura kana organic solvent. Kutadza kutevedzera murairo uyu kunogona kukonzera kuvhunduka kwemagetsi kana moto.
3. Usashandise yuniti iri panzvimbo inobvira/inoputika/inoparadza gasi, mwando, zuva rakananga, kupisa kwakapenya, kuzunguzika, kukanganiswa, kana munyu. Kutadza kutevedzera murayiro uyu kunogona kukonzera moto kana kuputika.
4. Chengetedza simbi chip, huruva, uye waya zvisaririra kubva pakuyerera kupinda muyuniti. Kutadza kutevedzera murairo uyu kunogona kukonzera moto kana kukuvara kwechigadzirwa.

Kuraira Ruzivo

1. Chete cheTCN4S modhi.
2. Kana iri AC voltage modhi, SSR drive yekubuda nzira (yakajairwa ON / OFF control, cycle control, phase control) inowanikwa kusarudza.
   • Izvo zvataurwa pamusoro apa zvinogona kuchinja uye mamwe mamodheru anogona kumiswa pasina chiziviso.
   • Iva nechokwadi chekutevera yambiro yakanyorwa mubhuku rekuraira uye nehunyanzvi tsananguro (katalogi, peji remba).

Tsanangudzo

1. Pane tembiricha yemumba (23ºC±5ºC)
   • Pazasi pe200ºC ye thermocouple R(PR), S(PR) iri (PV ±0.5% kana ±3ºC, sarudza yepamusoro) ±1 digit
   • Kupfuura 200ºC ye thermocouple R(PR), S(PR) iri (PV ±0.5% kana ±2ºC, sarudza yepamusoro) ±1 digit - Thermocouple L (IC), RTD Cu50Ω iri (PV ±0.5% kana ±2ºC, sarudza yepamusoro) ± 1 digit Kunze kwekamuri tembiricha
   • Pazasi pe200ºC ye thermocouple R(PR), S(PR) iri (PV ±1.0% kana ±6ºC, sarudza yepamusoro) ±1 digit
   • Kupfuura 200ºC ye thermocouple R(PR), S(PR) iri (PV ±0.5% kana ±5ºC, sarudza yepamusoro) ±1 digit - Thermocouple L(IC), RTD Cu50Ω iri (PV ±0.5% kana
   • ± 3ºC, sarudza yepamusoro) ± 1 digit YeTCN4S- -P, wedzera ± 1℃ nekururama mwero. 2: Huremu hunosanganisira kurongedza. Huremu huri mumaparenthesi ndehwe unit chete. Kuramba kwezvakatipoteredza kwakayerwa pasina kutonhora kana kuomeswa.

Tsanangudzo Yechikamu

1. Ikozvino tembiricha (PV) kuratidza (Red)
   1. RUN mode: Ikozvino tembiricha (PV) kuratidza
   2. Parameter yekumisikidza modhi: Parameter kuratidza
2. Seta tembiricha (SV) kuratidza (Green)
   1. RUN mode: Seta tembiricha (SV) kuratidza
   2. Parameter yekumisikidza modhi: Parameter yekuisa kukosha kuratidza
3. Kudzora/Alarm inobuda kuratidza chiratidzo
   1. OUT: Inobatidza kana iyo control inobuda iri ON. Munguva yeSSR drive yekubuda mhando muCYCLE/PHASE control, ichi chiratidzo chinobatidza kana MV yadarika 3.0%. 2) AL1/AL2: Inobatidza kana alarm inobuda IRI.
4. Auto tuning chiratidzo AT chiratidzo chinopenya nesekondi yega yega panguva yekushanda otomatiki.
5. key Inoshandiswa paunopinda mumapoka eparameter, kudzokera kuRUN modhi, kufambisa paramita, uye kuchengetedza kuseta maitiro.
6. Kugadzirisa
   Inoshandiswa paunenge uchipinda muset value shanduko modhi, digit inofamba uye digit kumusoro/pasi.
7. Digital input key
   Dzvanya makiyi e3 sec. kushandisa seti basa (RUN/ STOP, alarm yekubuda patsva, auto tuning) mukiyi yekupinza yedhijitari [].
8. Tembiricha unit (ºC/℉) chiratidzo
   Inoratidza ikozvino tembiricha unit.

Input Sensor uye Temperature Range

Dimensions

Connections

Parameter Mapoka

Zvose Parameter

• Press kiyi pamusoro pe3 sec mune chero parameter boka, inochengetedza iyo yakatarwa kukosha uye inodzokera kuRUN modhi. (Kunze: Press kiyi kamwe muSV kuseta boka, inodzokera kuRUN modhi).
• Kana pasina kiyi yaiswa kwe30 sec., inodzokera kuRUN modhi otomatiki uye kukosha kweseti yeparameter haina kuchengetwa.
• Press kiyi zvakare mukati me1 sec. mushure mokudzokera kuRUN modhi, inofambira mberi yekutanga parameter yeyapfuura parameter boka.
• Press kiyi yekufambisa inotevera parameter.
• Parameter yamaka mukati inogona kusaratidzwa zvichienderana nemamwe ma parameter marongero. Seta parameta se'Parameta 2 boka → Parameta 1 boka → Kuseta boka reiyo set value' kurongeka uchifunga nezve hukama hweparameta yeboka rega rega.
• 1: Haisi kuratidzwa kune AC / DC simba remuenzaniso (TCN4 -22R).
• kiyi: Inofambisa parameter uye inochengetedza seti , kiyi: Inofamba digit, or kiyi: Inoshandura seti

Parameter 2group

SV kuseta
Iwe unogona kuseta tembiricha yekudzora nayo ,,, keys. Maseting ayo ari mukati meSV yakaderera muganho ukoshi [L-SV] kuenda kuSV yepamusoro-soro kukosha [H-SV].
Eg) Muchiitiko chekuchinja tembiricha kubva pa210ºC kuenda ku250ºC

Parameter reset
Reset ese ma parameters sefactory default. Bata kumberi + + makiyi e5 sec., kupinda parameter reset [INIT] parameter. Sarudza 'YES' uye ese ma paramita anogadzikiswa senge fekitori default. Sarudza 'NO' uye marongero apfuura anochengetwa. Kana kuseta parameter kukiya [LOC] kana kugadzirisa auto-tuning, parameter reset haisipo.

Mabasa

Kugadzirisa otomatiki [AT]
Kugadzirisa otomatiki kunoyera hunhu hwekudziya kwechinyorwa chekutonga uye mwero wekupindura wekupisa, wobva waona iyo inodiwa nguva yePID. (Kana control type [C-MD] yaiswa sePID, inoratidzwa.) Kushandiswa kwePID nguva nguva dzose kunoona mhinduro inokurumidza uye yakakwirira chaiyo tembiricha kutonga. Kana kukanganisa [OPEN] kukaitika panguva yekugadzira otomatiki, inomisa oparesheni iyi otomatiki. Kuti umise auto tuning, chinja seti se [OFF]. (Inochengetedza P, I, D tsika dzepamberi pekugadzirisa otomatiki.)

Hysteresis [HYS]
Kana iri ON/OFF control, isa pakati pe ON ne OFF nguva se hysteresis. (Kana rudzi rwekudzora [C-MD] rwakaiswa seONOF, inoratidzwa.) Kana hysteresis iri diki, inogona kukonzera kudzora kubuda kwekuvhima (kubvisa, kutaura) neruzha rwekunze, nezvimwe.

SSR drive inobuda sarudzo (SSRP basa) [SSrM]

• SSRP basa rinosarudzwa imwe yeyakajairwa ON/OFF control, cycle control, phase control nekushandisa yakajairwa SSR drive kubuda.
• Kuona kurongeka kwepamusoro uye kudhura kunoshanda tembiricha yekudzora semutsara kubuda (kutenderera kutonga uye chikamu chekutonga).
• Sarudza imwe yeyakajairwa ON/OFF control [STND], cycle control [CYCL] , phase control [PHAS] pa[SSrM] parameter yeparameter 2 boka. Kuti udzore kutenderera, batanidza zero cross turn-on SSR kana random turn-on SSR. Kuti uite chikamu chekutonga, batanidza zvisina kujairika kuvhura SSR.

Temperature controller

• Paunenge uchisarudza chikamu kana kutenderera kudzora modhi, magetsi ekupa mutoro uye tembiricha controller inofanira kunge yakafanana.
• Muchiitiko chekusarudza PID control type uye phase [PHAS] / cycle [PHAS] control inobuda modes, control cycle [T] haibvumidzwe kusetwa.
• Kune AC/DC power model (TCN -22R), iyi parameter haina kuratidzwa uye inowanikwa chete standard control nerelay kana SSR.

1. Yakajairwa ON / OFF yekudzora modhi [STND] Iyo modhi yekudzora mutoro nenzira imwechete neiyo Relay yekubuda mhando. (ON: chikamu chekubuda 100%, OFF: chikamu chekubuda 0%)
2. Cycle control mode [CYCL]
   Iyo modhi yekudzora mutoro nekudzokorora kuburitsa ON / OFF zvinoenderana nechiyero chekubuda mukati mekuseta kutenderera. Kuve nekuvandudza ON / OFF ruzha chimiro neZero Cross mhando.
3. Phase control mode [ PHAS]
   Iyo modhi yekudzora mutoro nekudzora chikamu mukati me AC hafu kutenderera. Seri control iripo. RANDOM Turn-on type SSR inofanirwa kushandiswa pane iyi modhi.

Digital input key ( 3sec.) []

Alarm

Seta ese ari maviri alarm mashandiro uye alarm sarudzo nekubatanidza. Alarm kubuda maviri uye imwe neimwe inoshanda yega. Kana tembiricha yazvino yabuda pa alarm range, alarm inodzima otomatiki. Kana alarm sarudzo iri alarm latch kana alarm latch uye standby sequence 1/2, dzvanya kiyi yekuisa yedhijitari( 3 sec., kiyi yekupinza yedhijitari[] yeparameta 2 boka rakaiswa seAlRE), kana KUDZIMA simba uye BATIDZA kujekesa alarm.

Alarm kushanda

• H: Alarm inobuda hysteresis [AHYS]

Alarm operation

• Mamiriro ekudzokororwa akateedzana akamirira 1, alarm latch uye standby kutevedzana 1: Simba ON Mamiriro ekushandiswazve kwekumira kwekutevedzana kwekuteerana kwekumira 2, alarm latch uye standby sequence 2: Simba ON, kushandura seti tembiricha, alarm tembiricha ( AL1, AL2) kana alarm operation (AL-1, AL-2), kuchinja STOP mode kuti RUN mode.

Sensor break alarm Basa iro alarm inobuda ichave ON kana sensor isina kubatana kana kana sensor kubviswa kwaonekwa panguva yekudzora tembiricha. Unogona kutarisa kana sensor yakabatana nebuzzer kana mamwe mayunitsi uchishandisa alarm inobuda kubata. Inosarudzwa pakati peyakajairwa alarm [SBaA] kana alarm latch [5BaB].

Loop break alarm (LBA)
Inotarisa control loop uye inoburitsa alarm nekushanduka kwekushisa kwechinyorwa. Zvekudziya kutonga (kutonhora kutonga), kana kudzora kubuda MV iri 100% (0% yekudzora kutonhora) uye PV haina kuwedzera kupfuura LBA yekuona bhendi [] panguva yekutarisa LBA nguva [[] panguva yekutarisa LBA nguva [], alarm inobuda inobatidza.

• Paunenge uchiita auto-tuning, LBA yekuona bhendi[LBaB] uye LBA yekutarisisa nguva inoiswa otomatiki zvichibva pane auto tuning kukosha. Kana alarm operation mode [AL-1, AL-2] yakaiswa se loop break alarm(LBA) [LBa ], LBA yekuona bhendi [LBaB] uye LBA yekutarisa nguva [] parameter inoratidzwa.

Reset nemawoko[]

• Manual reset [] by control result

Pakusarudza P/PD control mode, imwe tembiricha mutsauko uripo kunyangwe mushure mekunge PV yasvika pakugadzikana nekuti nguva yekukwira nekudonha kweheater haienderane nekuda kwehunhu hwekupisa kwezvinhu zvinodzorwa, senge kupisa, kugona kweheater. Uyu musiyano wetembiricha unonzi offset uye manual reset [] basa ndere kuseta/kururamisa kumisa. Kana PV neSV zvakaenzana, gadzirisa kukosha i50.0%. Mushure mekunge kutonga kwagadzikana, PV yakaderera pane SV, kukosha kwekugadzirisa kwapfuura 50.0% kana PV yakakwirira kudarika SV, reset value iri pasi pe50.0%.

Kugadziriswa kwekuisa[IN-B]
Controller pachayo haina zvikanganiso asi panogona kunge paine kukanganisa nekunze kwekupinza tembiricha sensor. Basa iri nderekugadzirisa kukanganisa uku. Eg) Kana tembiricha chaiyo iri 80ºC asi controller ichiratidza 78ºC, isa kukosha kwekugadzirisa [IN-B] se'002' uye controller inoratidza 80ºC. Semhedzisiro yekugadziriswa kwekuisa, kana ikozvino tembiricha kukosha (PV) iri pamusoro pega ega tembiricha renji rekuisa sensor, inoratidza 'HHHH' kana 'LLLL'.

Isa sefa yedhijitari[]
Kana tembiricha yazvino (PV) ichichinja-chinja kakawanda nekuchinja nekukurumidza kwechiratidzo chekuisa, inoratidza kuMV uye kudzora kwakagadzikana hazvigoneke. Naizvozvo, dhijitari sefa basa inodzikamisa tembiricha yazvino kukosha. For example, isa kukosha kwedhijitari yefirita se 0.4 sec, uye inoshandisa dhijitari sefa kune yekuisa kukosha panguva ye 0.4 sec uye inoratidza izvi zvakakosha. Tembiricha yazvino inogona kunge yakasiyana nekukosha kwekuisa chaiko.

Error

Display	Tsanangudzo	Kugadzirisa matambudziko
Vhura	Inopenya kana sensor yekupinza ikabviswa kana sensor isina kubatana.	Tarisa kupinza sensor mamiriro.
HHHH	Inopenya kana yakayerwa sensor yekupinza yakakwira kupfuura tembiricha.	Kana kupinza kuri mukati meyakayerwa tembiricha renji, chiratidziro ichi chinonyangarika.
Llll	Inopenya kana mesured sensor yekupinda yakaderera pane tembiricha renji

Factory Default

Installation

• Isa chigadzirwa mupaneru, simbisa bracket nekusaidzira nematurusi sezvaratidzwa pamusoro.

Yambiro panguva yekushandisa

1. Tevera mirairo mu 'Kuchenjerera panguva yekushandisa'. Zvikasadaro, Inogona kukonzera tsaona dzisingatarisirwi.
2. Tarisa polarity yematerminal usati waisa waya tembiricha sensor. Kune RTD tembiricha sensor, waya iyo se-3-waya mhando, uchishandisa tambo dzakafanana ukobvu nehurefu. Kune iyo thermocouple (CT) tembiricha sensor, shandisa iyo yakatemerwa muripo waya yekuwedzera waya.
3. Ramba kure nehigh voltage mitsara kana tambo dzemagetsi kudzivirira inductive ruzha. Muchiitiko chekuisa tambo yemagetsi uye mutsara wekuisa chiratidzo padhuze, shandisa mutsara sefa kana varistor patambo yemagetsi uye waya yakadzivirirwa pamutsetse wekuisa chiratidzo. Usashandise zvishandiso zviri pedyo zvinogadzira simba rakasimba remagineti kana ruzha rwepamusoro-soro.
4. Isa svumbunuro yemagetsi kana redunhu breaker munzvimbo inosvikirika nyore yekugovera kana kubvisa magetsi.
5. Usashandise iyo unit kune chimwe chinangwa (semuenzaniso voltmeter, ammeter), asi kune tembiricha controller.
6. Paunenge uchishandura sensor yekupinza, dzima simba kutanga usati wachinja. Mushure mekushandura sensor yekupinza, shandura kukosha kweiyo inoenderana parameter.
7. 24VAC, 24-48VDC magetsi anofanirwa kuve akavharirwa uye mashoma voltage/yazvino kana Kirasi 2, SELV magetsi ekupa mudziyo.
8. Ita nzvimbo inodiwa yakapoteredza chikwata chemwaranzi yekupisa. Kuti uite kuyerwa kwetembiricha kwakaringana, dziisa iyo unit pamusoro pemaminetsi makumi maviri mushure mekubatidza simba.
9. Ita shuwa kuti simba rekupa voltage inosvika kune yakarongwa voltage mukati me2 sec mushure mekupa simba.
10. Usaisa waya kumaterminals asina kushandiswa.
11. Ichi chikwata chinogona kushandiswa munzvimbo dzinotevera.
    1. Mumba (mumamiriro ekunze akaiswa mu 'Specifications')
    2. Altitude max. 2,000m
    3. Dhigirii rekusvibisa 2
    4. Kuisa chikamu II

Zvigadzirwa Zvikuru

• Photoelectric Sensors
• Fiber Optic Sensors
• Door Sensors
• Door Side Sensors
• Nzvimbo Sensors
• Proximity Sensors
• Pressure Sensors
• Rotary Encoders
• Connector/Sockets
• Kushandura Mode Power Supplies
• Kudzora Kuchinja/Lamps/Buzzers
• I / O Terminal Zvidhinha & Tambo
• Stepper Motors / Vatyairi / Motion Controllers
• Graphic/Logic Panels
• Field Network Devices
• Laser Marking System (Fiber, Co₂, Nd: YAG)
• Laser Welding / Kucheka System
• Temperature Controllers
• Tembiricha / Humidity Transducers
• SSRs / Power Controllers Counters
• Timers
• Panel Meters
• Tachometer/Pulse (Rate) Mamita
• Display Units
• Sensor Controllers
• http://www.autonics.com

HEADQUARTERS:

• 18, Bansong-ro 513beon-gil, Haeundae-gu, Busan,
• South Korea, 48002
• TEL: 82-51-519-3232
• E-mail: sales@autonics.com

Nhoroondo ye Instrukart Holdings
India Yemahara: 1800-121-0506 | Ph: +91 (40)40262020 Mob +91 7331110506 | Email : info@instrukart.com #18, Street-1A, Czech Colony, Sanath Nagar, Hyderabad -500018, INDIA.

Zvinyorwa / Zvishandiso

Autonics TCN4 SERIES Dual Indicator Temperature Controller [pdf] Bhuku reMirayiridzo TCN4 SERIES Dual Indicator Temperature Controller, TCN4 SERIES, Dual Indicator Temperature Controller, Indicator Temperature Controller, Temperature Controller, Controller

References

• User Manual