fa'apipi'i Fa'afefea ona Fa'aoga le Z-Axis Extension Module

Upu Tomua
Ole ta'iala lea ile fa'aogaina ole Z-Axis Extension Module ile Snapmaker Original. Ua vaevaeina i ni vaega se lua:

1. Tuuina atu faʻamatalaga i le faʻapotopotoga.
2. Faʻaalia le faʻatulagaina o Snapmaker Luban.

Fa'ailoga Fa'aaogaina
Lapata'iga: O le le amana'iaina o lea ituaiga fe'au e ono i'u ai i le fa'aletonu po'o le fa'aleagaina o le masini ma manu'a ai tagata fa'aoga
Fa'aaliga: Fa'amatalaga e tatau ona e silafia i le faagasologa atoa

• Ia mautinoa o loʻo faʻasaga le vaega faʻamalama i le ala saʻo.

Fonotaga

1. Ia mautinoa ua pe le masini.
   Aveese uma uaea.
   Faatali pe a ma le 5 minute se'i maalili le masini pe a uma ona lolomi.
2. Aveese le Uu Filament.
   • Aveese le X-Axis
     (fa'atasi ma 3D Pinting Module fa'apipi'i).
   • Aveese le Pule.
3. Aveese le Z-Axis muamua.
   Fa'apipi'i le Z-Axis Extension Module (Z-Axis mulimuli ane).
4. Fa'apipi'i le Filament Holder i luga ole Z-Axis.
5. Fa'apipi'i le XAxis (fa'atasi ma 3D Printing Module fa'apipi'i) i le Z-Axis.
6. Fa'apipi'i le Pule i le Z-Axis.
7. Fa'afeso'ota'i uma uaea ua tatala i le Laasaga 1.

Fa'atulagaina o Lubann

1. Ia mautinoa o loʻo faʻafouina lau firmware i le 2.11 lata mai, ma faʻapipiʻi Snapmaker Luban:
   https://snapmaker.com/product/snapmaker-original/downloads.
2. Fa'afeso'ota'i lau PC ma le masini e fa'aaoga ai le uaea USB ua saunia, ma fa'aola le eletise.Fa'aaliga: Afai e te le maua le laina telefoni o lau masini, taumafai e faʻapipiʻi le avetaavale CH340 ile:
   https://snapmaker.com/product/snapmaker-original/dowloads.
3.  Tatala Snapmaker Luban.
   • Mai le itu agavale, ulufale i le Workspace
   •  I le pito i luga agavale, su'e Feso'ota'iga ma kiliki le fa'afou fa'amau e toe fa'asolo ai lisi o ports
   • Kiliki le fa'amau fa'amau ma filifili le laina telefoni o lau masini, ma kiliki Connect.
4. Filifili Custom ma le meafaigaluega e fesoʻotaʻi ma le masini pe a faʻamalosia.
5. Kiliki Fa'atonu i le itu agavale, filifili Fa'atonu masini.
   • Tusa 125, 125, 221 eseese i avanoa avanoa i lalo ole X, Y, ma le Z.
   • I lalo o le Z axis Extension Module, kiliki le fa'amau i lalo ma filifili I luga.
   • Kiliki Save Suiga.
6. Tap Controls i luga o le Touchscreen, ma tap Home AXes e fai ai se sauniga o le fale.
7. Fa'ata'atia le Moega vevela. Mo fa'amatalaga auiliili, tagai ile Quick Start Guide. Ua sauni nei lau Z-Axis Extension Module e alu.

Fa'aaliga: Afai o loʻo faʻaogaina e lau masini le 3D Printing Module, e vaʻai pe manuia le faʻatulagaga, tap Settings About>Fausia le Volume i luga o le Touchscreen.

Pepa / Punaoa

snapmaker Fa'afefea ona Fa'aoga le Z-Axis Extension Module [pdf] Fa'atonu Taiala Fa'afefea ona fa'aoga le Z-Axis Extension Module, Z-Axis Extension Module, Extension Module, Module

Fa'asinomaga

• Tusi Taiala