ABX00071 Laiti Laiti Module Tusitaiala a le Pule

O le laupapa o loʻo faʻaalia ai se gaioiga faʻatasi ma se pine faʻapitoa
galuega faatino. O pine A4 ma le A5 e fautuaina mo le fa'aogaina o le I2C Bus
nai lo mea fa'aoga analog.

IMU

O le Nano 33 BLE Rev2 o loʻo tuʻuina atu ai gafatia IMU ma se
tu'ufa'atasiga o BMI270 ma BMM150 ICs mo le 9-axis sensing.

Laau Malosi

E mafai ona fa'aola le laupapa e ala i feso'ota'iga USB, VIN, po'o pine VUSB i luga
ulutala. Tulaga aupito maualalo voltage mo le sapalai eletise USB ua faamaoti i
fa'amautinoa le fa'agaioiga lelei.

Fa'atonuga o le Fa'aaogaina o Mea

1. Amataina

Ina ia amata faʻaaoga le laupapa, mulimuli i laasaga nei:

IDE: Amata ile Atina'e Fa'atasi
Siosiomaga mo polokalame.
Arduino Cloud Editor: Fa'aaoga le fa'avae ao
faatonu mo coding faigofie.

Arduino Ao: Faʻafesoʻotaʻi i Arduino Cloud mo
galuega fa'aopoopo.

2. Pinouts Feso'ota'i

Va'ai ile tusi fa'aoga mo fa'amatalaga auiliili ile USB,
ulutala, ma debug so'oga pinouts.

3. Galuega a le Komiti Faatino

Saili samptusi ata, punaoa i luga ole laiga, ma aoao e uiga i laupapa
faiga toe faaleleia.

4. Fa'amatalaga Fa'ainisinia

Malamalama i le otootoga o le laupapa ma faʻamatalaga faʻapipiʻi pu
mo le tuufaatasia faaletino.

FAQ (Frequently Asked Questions)

Q: E mafai ona feso'ota'i sa'o le Nano 33 BLE Rev2 i le 5V
faailoilo?

A: Leai, na'o le lagolagoina e le laupapa le 3.3VI / Os ma e le o le 5V fa'apalepale.
Feso'ota'i faailoilo 5V e mafai ona fa'aleagaina le laupapa.

Q: E faʻafefea ona tuʻuina atu le mana i le laupapa?

A: E mafai ona fa'aola le laupapa e ala i le feso'ota'iga USB, VIN, po'o pine VUSB
i luga o ulutala. Ia mautinoa sa'o le sao voltage mo sapalai USB.

“`

View Fullscreen

Arduino® Nano 33 BLE Rev2
Tusi Taiala Fa'asinomaga SKU: ABX00071
Fa'amatalaga
O le Arduino® Nano 33 BLE Rev2* o se laʻititi laʻititi laʻititi o loʻo iai le NINA B306 module, faʻavae i luga o Nordic nRF52480 ma o loʻo i ai le Arm® Cortex®-M4F. O le BMI270 ma le BMM150 e tu'u fa'atasi se IMU 9-axis. O le module e mafai ona faʻapipiʻiina e avea o se vaega DIP (pe a faʻapipiʻi ulutala pine) poʻo se vaega SMT, faʻapipiʻi saʻo e ala i pads castellated. *Nano 33 BLE Rev2 oloa e lua SKU:
E aunoa ma ni ulutala (ABX00071) ma ulutala (ABX00072)
Vaega Fa'atatau
Fausia, faʻaleleia, faʻaoga IoT

1 / 15

Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

Arduino® Nano 33 BLE Rev2

Vaega
NINA B306 Module
Processor
64 MHz Arm® Cortex®-M4F (faatasi ai ma le FPU) 1 MB Flash + 256 kB RAM
Bluetooth® 5 multiprotocol leitio
2 Mbps CSA #2 Fa'aopoopo Fa'asalalauga Va'ava'ai +8 dBm TX mana -95 dBm ma'ale'ale 4.8 mA i le TX (0 dBm) 4.6 mA i le RX (1 Mbps) Tu'ufa'atasi balun ma 50 fa'ai'uga ta'itasi IEEE 802.15.4 lagolago leitio Fa'aigoa Zigbee.
Peripherals
Saosaoa atoa 12 Mbps USB NFC-A tag Arm® CryptoCell CC310 subsystem saogalemu QSPI/SPI/TWI/I²S/PDM/QDEC Saosaoa maualuga 32 MHz SPI Quad SPI interface 32 MHz EasyDMA mo feso'ota'iga numera uma 12-bit 200 ksps ADC 128 bit AES/ECB/CCM/AAR co-processor
BMI270 6-axis IMU (Accelerometer ma Gyroscope)
16-bit 3-axis accelerometer ma ± 2g/±4g/±8g/±16g laina 3-axis gyroscope ma ±125dps/±250dps/±500dps/±1000dps/±2000dps laina
BMM150 3-axis IMU (Manetometer)
3-axis numera geomagnetic sensor 0.3T iugafono ±1300T (x,y-axis), ±2500T (z-axis)
MP2322 DC-DC
Fa'atonutonu mea e tu'uina atu voltage mai luga i le 21V ma le itiiti ifo o le 65% lelei @maualalo uta Sili atu i le 85% lelei @12V

2 / 15

Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

Arduino® Nano 33 BLE Rev2

Mataupu

1 O le Komiti Faatino

1.1 Fa'ailoga

1.1.1 Tulaga Fautuaina Faagaioiga

1.2 Fa'aaogaina Malosiaga

2 Galuega Fa'atinoview

2.1 Laupapa Topology

2.2 Processor

2.3 IMU

2.4 Laau Malosi

2.5 Ata poloka

3 Galuega Fa'atonu

3.1 Amata – IDE

3.2 Amataina - Arduino Cloud Editor

3.3 Amataina - Arduino Cloud

3.4 Sample Tusitusi

3.5 Punaoa i luga ole laiga

3.6 Toe Fa'aleleia a le Komiti Fa'atonu

4 Pinouts Feso'ota'i

4.1 USB

4.2 Ulutala

4.3 Debug

5 Fa'amatalaga Fa'ainisinia

5.1 Otootoga o le Laupapa ma Pu Fa'amau

6 Tusipasi

6.1 Ta'utinoga o le tausisia CE DoC (EU)

6.2 Ta'utinoga o le tausisia i le EU RoHS & REACH 211 01/19/2021

6.3 Tautinoga o Minerale Fete'ena'i

7 FCC Lapataiga

8 Fa'amatalaga a Kamupani

9 Fa'amaumauga Fa'asinomaga

10 Toe Iloilo Tala'aga

3 / 15

Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

Arduino® Nano 33 BLE Rev2

1 O le Komiti Faatino
E pei o laupapa uma o le Nano form factor, Nano 33 BLE Rev2 e leai se uta maa ae e mafai ona faʻaosoina e ala ile USB poʻo ulutala.
FAAMANATU: Nano 33 BLE Rev2 e na'o le lagolagoina o le 3.3 VI/Os ma e LĒ 5V fa'apalepale fa'amolemole ia mautinoa e te le o fa'afeso'ota'i sa'o fa'ailoga 5 V i le laupapa nei pe o le a fa'aleagaina. E le gata i lea, e ese mai i isi laupapa Arduino Nano e lagolagoina le 5 V galuega, o le 5V pine e LĒ maua ai vol.tage ae e sili atu ona fesoʻotaʻi, e ala i se osooso, i le USB power input.
1.1 Fa'ailoga

1.1.1 Tulaga Fautuaina Faagaioiga

Faailoga

Fa'amatalaga Tapula'a fa'asao fa'asao mo le laupapa atoa:

1.2 Fa'aaogaina Malosiaga

Fa'ailoga PBL PLP PMAX

Fa'amatalaga Fa'aaogāina o le malosi ma le pisi pisi Fa'aaogā le paoa i lalo ole paoa Fa'aaogāina Malosi maualuga

Min -40 °C ( 40 °F)

Max 85 °C (185 °F)

Min Typ Max Unit

TBC

4 / 15

Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

2 Galuega Fa'atinoview
2.1 Laupapa Topology
Luga:

Arduino® Nano 33 BLE Rev2

Topology laupapa pito i luga

Ref. Fa'amatalaga U1 NINA-B306 Module Bluetooth® Low Energy 5.0 Module U2 BMI270 Sensor IMU U7 BMM150 Magnetometer IC SJ5 VUSB Jumper
Lalo:

Ref. Fa'amatalaga U6 MP2322GQH La'asaga i lalo Lisi PB1 IT-1185AP1C-160G-GTR Pusa faamau DL1 Led L

5 / 15

Board topology bot Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

Arduino® Nano 33 BLE Rev2

Ref.

Fa'amatalaga

SJ1

VUSB Jumper

SJ3

3v3 Fa'aoso

Ref.

Fa'amatalaga

SJ2

D7 Tagata osooso

SJ4

D8 Tagata osooso

2.2 Processor
Ole Fa'agasolo Autu ole Arm® Cortex®-M4F e o'o atu ile 64 MHz. O le tele o ona pine e feso'ota'i i ulutala i fafo ae o nisi o lo'o fa'aagaga mo feso'ota'iga i totonu ma le module uaealesi ma luga ole I2C peripherals (IMU ma Crypto).
FAAMANATU: E ese mai i isi laupapa Arduino Nano, o pine A4 ma le A5 o loʻo i ai se toso i luga i totonu ma e le mafai ona faʻaaogaina o se I2C Bus ona e le fautuaina le faʻaogaina o mea faʻaoga analog.

2.3 IMU
Nano 33 BLE Rev2 e maua ai le IMU gafatia ma le 9-axis, e ala i le tuʻufaʻatasia o BMI270 ma BMM150 ICs. O le BMI270 e aofia uma ai le tolu-axis gyroscope faʻapea foʻi ma le tolu-axis accelerometer, ae o le BMM150 e mafai ona faʻalogoina fesuiaiga o le mageta i itu uma e tolu. O fa'amatalaga na maua e mafai ona fa'aoga mo le fuaina o fa'asologa o gaioiga fa'apitoa fa'apea fo'i ma le a'oa'oina o masini.

2.4 Laau Malosi
E mafai ona fa'aola le laupapa e ala i feso'ota'iga USB, VIN po'o VUSB pine i luga o ulutala.

Laau malosi
FAAMANATU: Talu ai ona o le VUSB e fafaga le VIN e ala i le Schottky diode ma le DC-DC regulator ua faʻamaonia le laʻititi o le vol.tage 4.5 V le pito maualalo voltage mai le USB e tatau ona fa'aopoopo i le voltage i le va o le 4.8 V i le 4.96 V e fa'atatau i le taimi nei o lo'o tusia.

6 / 15

Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

2.5 Ata poloka

Arduino® Nano 33 BLE Rev2

Ata poloka

7 / 15

Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

Arduino® Nano 33 BLE Rev2
3 Galuega Fa'atonu
3.1 Amata – IDE
Afai e te mana'o e fa'apolokalame lau Nano 33 BLE Rev2 a'o e tuusao e mana'omia le fa'apipi'i o le Arduino Desktop IDE [1] E fa'afeso'ota'i le Nano 33 BLE Rev2 i lau komepiuta, e te mana'omia se uaea Micro-B USB. E maua ai foi le malosiaga i le laupapa, e pei ona faʻaalia e le LED.
3.2 Amataina - Arduino Cloud Editor
O laupapa Arduino uma, e aofia ai le tasi, galue i fafo-o-le-pusa i luga o le Arduino Cloud Editor [2], e ala i le na o le faʻapipiʻiina o se mea faʻapipiʻi faigofie. O le Arduino Cloud Editor o loʻo talimalo i luga o le initaneti, o le mea lea o le a faʻafouina pea ma faʻamatalaga lata mai ma lagolago mo laupapa uma. Mulimuli i le [3] e amata fa'ailoga i luga ole su'esu'ega ma fa'ae'e au ata tusi ile lau laupapa.
3.3 Amataina - Arduino Cloud
O oloa uma e fa'aogaina e Arduino IoT o lo'o lagolagoina i Arduino Cloud lea e fa'atagaina ai oe e fa'amauina, kalafi ma au'ili'ili fa'amatalaga fa'amatalaga, fa'aoso mea tutupu, ma fa'autometi lou fale po'o lau pisinisi.
3.4 Sample Tusitusi
SampO ata tusi mo le Nano 33 BLE Sense e mafai ona maua i le "Examples" lisi i le Arduino IDE poʻo le "Built-in Examples” vaega o le Arduino Docs webnofoaga.
3.5 Punaoa i luga ole laiga
I le taimi nei ua e faʻaogaina faʻavae o mea e mafai ona e faia i le laupapa e mafai ona e suʻesuʻeina avanoa e le gata o loʻo tuʻuina mai e ala i le siakiina o galuega faʻafiafia i Arduino Project Hub [4], le Arduino Library Reference [5] ma le faleoloa i luga ole laiga e te manaʻo ai. mafai ona fa'atutusa lau laupapa i masini, fa'agaioia ma isi mea.

8 / 15

Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

Arduino® Nano 33 BLE Rev2
3.6 Toe Fa'aleleia a le Komiti Fa'atonu
O laupapa Arduino uma o loʻo i ai se faʻapipiʻi faʻapipiʻiina e mafai ai ona faʻapipiʻi le laupapa e ala i le USB. Afai e loka e se ata tusi le faagasologa ma e le toe mafai ona oo atu le laupapa e ala i le USB e mafai ona ulufale i le faiga bootloader e ala i le faaluaina o le faamau toe setiina pe a uma le pule i luga o le laupapa.
4 Pinouts Feso'ota'i

9 / 15

Pinout Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

Arduino® Nano 33 BLE Rev2

4.1 USB

Ituaiga Galuega Fa'amau

Fa'amatalaga

1 VUSB

Malosiaga

Malosiaga Tuuina atu. Afai e fa'aola le laupapa e ala i le VUSB mai le fa'auluuluga o le mea lea (1)

2 D-

Fa'amatalaga fa'aeseese USB -

3 D+

Faʻamatalaga eseese USB +

4 ID

fa'atusa

Filifilia le fa'aogaina o le Host/Device

5 NNU

Malosiaga

Eleele Eleele

4.2 Ulutala

O lo'o fa'aalia e le laupapa ni feso'ota'iga 15-pin e lua e mafai ona fa'apipi'i fa'atasi ma fa'aulu fa'amau pe fa'asoloina e ala i vias fa'asalaina.

Ituaiga Galuega Fa'amau

1 D13

Faafuainumera

2 +3V3

Malosiaga

3 AREF

fa'atusa

4 A0/DAC0 Analog

5 A1

fa'atusa

6 A2

fa'atusa

7 A3

fa'atusa

8 A4/SDA Analog

9 A5/SCL Analog

10 A6

fa'atusa

11 A7

fa'atusa

12 VUSB

Malosiaga i totonu/Ofo

13 RST

Digital In

14 NNU

Malosiaga

15 VIN

Malosiaga i totonu

16 TX

Faafuainumera

17 RX

Faafuainumera

18 RST

Faafuainumera

19 NNU

Malosiaga

20 D2

Faafuainumera

21 D3/PWM Numera

22 D4

Faafuainumera

23 D5/PWM Numera

24 D6/PWM Numera

25 D7

Faafuainumera

26 D8

Faafuainumera

27 D9/PWM Numera

28 D10/PWM Numera

29 D11/MOSI Numera

Fa'amatalaga GPIO Fa'alotoifale fa'atupuina le mana fa'aogaina i masini fafo Fa'amatalaga Analog; e mafai ona faʻaaogaina e avea ma GPIO ADC i totonu / DAC fafo; e mafai ona faʻaaogaina e avea ma GPIO ADC i totonu; e mafai ona faʻaaogaina e avea ma GPIO ADC i totonu; e mafai ona faʻaaogaina e avea ma GPIO ADC i totonu; e mafai ona faʻaaogaina e avea ma GPIO ADC i totonu; I2C SDA; E mafai ona faʻaaogaina e avea ma GPIO (1) ADC i totonu; I2C SCL; E mafai ona faʻaaogaina e avea ma GPIO (1) ADC i totonu; e mafai ona faʻaaogaina e avea ma GPIO ADC i totonu; e mafai ona faʻaaogaina e pei o GPIO masani NC; e mafai ona fa'afeso'ota'i i le VUSB pine o le USB connector e ala i le fa'apu'upu'u o se osooso Fa'aulu maualalo le fa'aoga (fa'alua o pine 18) Malosiaga Ground Vin Malosiaga fa'aoga USART TX; e mafai ona faʻaaogaina e pei o GPIO USART RX; e mafai ona fa'aaogaina e fai ma GPIO Active maualalo toe fa'aofi fa'aoga (fa'alua o pine 13) Malosiaga Eleele GPIO GPIO; e mafai ona faʻaaogaina e pei o le PWM GPIO GPIO; e mafai ona faʻaaogaina e pei o le PWM GPIO, e mafai ona faʻaaogaina e pei o le PWM GPIO GPIO GPIO; e mafai ona faʻaaogaina e avea ma PWM GPIO; e mafai ona faʻaaogaina e pei o le PWM SPI MOSI; e mafai ona faʻaaogaina e avea ma GPIO

10 / 15

Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

Arduino® Nano 33 BLE Rev2

Ituaiga Fa'aga Fa'amau 30 D12/MISO Digital

Fa'amatalaga SPI MISO; e mafai ona faʻaaogaina e avea ma GPIO

4.3 Debug

I le pito i lalo o le laupapa, i lalo o le module fesoʻotaʻiga, faʻailoga debug ua faʻatulagaina e pei o 3 × 2 pads suʻega ma le 100 mil pitch ma le pine 4 ua aveese. O le pine 1 o lo'o fa'aalia i le Ata 3 Tulaga Feso'ota'i

Galuega Fa'amau 1 +3V3 2 SWD 3 SWCLK 5 GND 6 RST

Ituaiga Malosi i fafo Faafuainumera Numera I Malosi Faafuainumera In

Fa'amatalaga Fa'alotoifale fa'aola eletise e fa'aaogaina e pei o voltage fa'asinoga nRF52480 Uaea Tasi Debug Fa'amatalaga nRF52480 Uaea Tasi Debug Uati Malosi Eleele Malosiaga maualalo toe fa'aofiina.

5 Fa'amatalaga Fa'ainisinia
5.1 Otootoga o le Laupapa ma Pu Fa'amau
O fua a le laupapa e fefiloi i le va o le metric ma le imperial. E fa'aogaina faiga fa'a-Imperial e fa'atumauina ai le 100 mil pitch grid i le va o laina pine ina ia fa'ataga ai latou e fa'apipi'i i se laupapa falaoa ae o le umi o le laupapa o le Metric.

11 / 15

Fa'atulagaina o le laupapa

Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

Arduino® Nano 33 BLE Rev2

6 Tusipasi

6.1 Ta'utinoga o le tausisia CE DoC (EU)
Matou te taʻutino atu i lalo o la matou matafaioi e faʻapea o oloa o loʻo i luga e ogatusa ma manaʻoga taua o taʻiala a le EU o loʻo mulimuli mai ma o lea e agavaa ai mo le feoai saoloto i totonu o maketi e aofia ai le Europa Europa (EU) ma le European Economic Area (EEA).

6.2 Ta'utinoga o le tausisia i le EU RoHS & REACH 211 01/19/2021

O laupapa Arduino o loʻo tausisia le RoHS 2 Directive 2011/65/EU o le Palemene Europa ma le RoHS 3 Directive 2015/863/EU o le Fono a Iuni 4 Iuni 2015 i le faʻatapulaʻaina o le faʻaaogaina o nisi mea matautia i mea eletise ma eletise.

Mea Ta'ita'i (Pb) Cadmium (Cd) Mercury (Hg) Hexavalent Chromium (Cr6+) Poly Brominated Biphenyls (PBB) Poly Brominated Diphenyl ethers (PBDE) Bis(2-Ethylhexyl} phthalate (DEHP) Benzyl butyl phthalate (BBP) Dibutyl phthalate (BBP) DBP) Diisobutyl phthalate (DIBP)

Tapulaa maualuga (ppm) 1000 100 1000 1000 1000 1000 1000 1000 1000 1000

Tuusaunoaga: E leai ni tuusaunoaga e talosagaina.

O laupapa Arduino o lo'o tausisia atoatoa mana'oga fa'atatau i le Tulafono Fa'atonutonu a Europa (EC) 1907/2006 e uiga i le Fa'amauina, Iloiloga, Fa'atagaga ma Fa'atapula'aina o Vailaau Fa'asaina (REACH). Matou te taʻutino atu e leai se SVHCs (https://echa.europa.eu/web/guest/candidate-list-table), o le Lisi o Sui Tofia o mea e sili ona popole mo le faʻatagaga o loʻo tuʻuina atu nei e le ECHA, o loʻo i ai i oloa uma (ma faʻapea foʻi afifi) i le aofaʻi o le aofaʻi i se faʻatonuga tutusa pe sili atu i le 0.1%. I le mea e gata mai ai lo matou iloa, matou te tautino atu foi oa matou oloa e le o iai ni mea o loʻo lisiina i luga o le "Lisi Faʻatagaina" (Faʻaopoopoga XIV o tulafono a le REACH) ma mea o loʻo popole tele (SVHC) i soʻo se aofaiga taua e pei ona faʻamaonia. e le Annex XVII o le Lisi o Sui Fa'asalalau fa'asalalau e ECHA (European Chemical Agency) 1907 /2006/EC.

12 / 15

Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

Arduino® Nano 33 BLE Rev2
6.3 Tautinoga o Minerale Fete'ena'i
I le avea ai o se kamupani faʻavaomalo o mea eletise ma eletise, ua iloa e Arduino a tatou matafaioi e tusa ai ma tulafono ma tulafono faatonutonu e uiga i Feteʻenaʻiga Minerals, aemaise lava le Dodd-Frank Wall Street Reform and Consumer Protection Act, Vaega 1502. minerale pei ole Tin, Tantalum, Tungsten, poʻo le Auro. O minerale fete'ena'i o lo'o i totonu oa tatou oloa i le tulaga o le solder po'o se vaega i u'amea u'amea. I le avea ai o se vaega o la matou su'esu'ega talafeagai, ua fa'afeso'ota'i e Arduino le au fa'atau oloa i totonu o la matou sapalai filifili e fa'amaonia lo latou tausisia pea o tulafono faatonutonu. E tusa ai ma faʻamatalaga na maua mai i le taimi nei, matou te taʻutino atu oa matou oloa o loʻo aofia ai Minerale Feteʻenaʻi e maua mai i nofoaga e leai ni feteenaiga.
7 FCC Lapataiga
So'o se Suiga po'o ni suiga e le'i fa'amaonia manino e le itu e nafa ma le usita'ia e mafai ona fa'aleaogaina le pule a le tagata fa'aoga e fa'agaioi ai masini. O lenei masini e tausisia le vaega 15 o Tulafono FCC. O le fa'agaioiga e fa'atatau i aiaiga nei e lua: (1) O lenei masini e le mafai ona fa'alavelave fa'alavelave (2) e tatau i lenei masini ona talia so'o se fa'alavelave e maua, e aofia ai fa'alavelave e ono fa'atupu ai le le mana'omia. FCC RF Radiation Faʻaaliga Faʻaaliga:
1. O lenei Transmitter e le tatau ona tu'u fa'atasi pe fa'agaioi fa'atasi ma so'o se isi lava antenna po'o le transmitter. 2. O nei mea faigaluega e ogatasi ma tapula'a fa'aola fa'avevela RF ua fa'ata'atia mo se si'osi'omaga le pulea. 3. O nei meafaigaluega e tatau ona faʻapipiʻi ma faʻaogaina i se mamao maualalo o le 20cm i le va o le radiator &
lou tino.
Gagana Peretania: O tusi lesona a le tagata fa'aoga mo masini leitio e tuusaunoaina laisene e tatau ona i ai le fa'aaliga o lo'o mulimuli mai pe tutusa i se nofoaga iloga i totonu o le tusi fa'aoga, i se isi itu i luga o le masini po'o mea uma e lua. O lenei masini e fa'amalieina ma fa'ata'ita'iga RSS e tuusaunoa laisene a Industry Canada. O le fa'agaioiga e fa'atatau i aiaiga nei e lua: (1) e le mafai e lenei masini ona fa'alavelave (2) e tatau i lenei masini ona talia so'o se fa'alavelave, e aofia ai fa'alavelave e ono fa'atupu ai le le mana'omia o le fa'aogaina o le masini. Falani: Le présent appareil est conforme aux CNR d'Industrie Canada e fa'aoga ai aux appareil tuusaunoaina le laisene. L'exploitation est autorisée aux deux conditions suivantes : (1) l' appareil nedoit pas produire de brouillage (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, e pei o le brouillage e ono afaina i le comromettre le fonction . Lapataiga a le IC SAR: Igilisi E tatau ona fa'apipi'i ma fa'agaoioia meafaigaluega i se mamao la'ititi o le 20 cm i le va o le radiator ma lou tino.

13 / 15

Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

Arduino® Nano 33 BLE Rev2

Falani: Lors de l' installation et de l' exploitation de ce dispositif, o le mamao e oo atu i le radiateur ma le tino e 20 cm.

Taua: O le vevela o le EUT e le mafai ona sili atu i le 85 ma e le tatau ona maualalo ifo i le -40.

O le mea lea, Arduino Srl ta'utino atu o lenei oloa e ogatasi ma mana'oga taua ma isi aiaiga talafeagai o le Directive 2014/53/EU. O lenei oloa e faʻatagaina e faʻaaogaina i totonu o setete uma o le EU.

Fa'asologa o laina 863-870Mhz

Malosi maualuga o le gaosiga (ERP) TBD

8 Fa'amatalaga a Kamupani

Igoa Kamupani Tulaga a le Kamupani

Arduino Srl Via Andrea Appiani 25 20900 MONZA Italia

9 Fa'amaumauga Fa'asinomaga

Fa'asinoga Arduino IDE (Desktop) Arduino Cloud Editor Arduino Cloud Editor – Amataina Arduino Project Hub Library Reference Forum
Nina B306

So'oga https://www.arduino.cc/en/software https://create.arduino.cc/editor
https://docs.arduino.cc/arduino-cloud/guides/editor/
https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending https://www.arduino.cc/reference/en/ http://forum.arduino.cc/ https://content.u-blox.com/sites/default/files/NINA-B3_DataSheet_UBX17052099.pdf

14 / 15

Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

Arduino® Nano 33 BLE Rev2

10 Toe Iloilo Tala'aga

Date 25/04/2024 2024/02/21

Suiga Fa'afou feso'ota'iga i le Cloud Editor Muamua Fa'asalalau

15 / 15

Arduino® Nano 33 BLE Rev2

Suia: 13/06/2024

Pepa / Punaoa

Arduino ABX00071 Laiti Laiti Module [pdf] Tusi Lesona a le Pule
ABX00071.

Fa'asinomaga

Tusi Taiala

ABX00071 Laiti Laiti Module

Fa'amatalaga

Fa'amatalaga o oloa

Faagaioia i Lugaview

Laupapa Topology

Processor

IMU

Laau Malosi

Fa'atonuga o le Fa'aaogaina o Mea

1. Amataina

2. Pinouts Feso'ota'i

3. Galuega a le Komiti Faatino

4. Fa'amatalaga Fa'ainisinia

FAQ (Frequently Asked Questions)

Q: E mafai ona feso'ota'i sa'o le Nano 33 BLE Rev2 i le 5V
faailoilo?

Q: E faʻafefea ona tuʻuina atu le mana i le laupapa?

Pepa / Punaoa

Fa'asinomaga

Tuu se faamatalaga

Fa'aleaogaina le tali

ABX00071 Laiti Laiti Module

Fa'amatalaga

Fa'amatalaga o oloa

Faagaioia i Lugaview

Laupapa Topology

Processor

IMU

Laau Malosi

Fa'atonuga o le Fa'aaogaina o Mea

1. Amataina

2. Pinouts Feso'ota'i

3. Galuega a le Komiti Faatino

4. Fa'amatalaga Fa'ainisinia

FAQ (Frequently Asked Questions)

Q: E mafai ona feso'ota'i sa'o le Nano 33 BLE Rev2 i le 5V faailoilo?

Q: E faʻafefea ona tuʻuina atu le mana i le laupapa?

Pepa / Punaoa

Fa'asinomaga

Fa'amatalaga Fa'atatau

Tuu se faamatalaga

Fa'aleaogaina le tali

Q: E mafai ona feso'ota'i sa'o le Nano 33 BLE Rev2 i le 5V
faailoilo?