ABX00071 Karamin Girman Girman Module Manual

Allon yana da na'ura mai sarrafawa tare da takamaiman fil
ayyuka. Ana ba da shawarar fil A4 da A5 don amfani da Bus na I2C
maimakon abubuwan shigar da analog.

IMU

Nano 33 BLE Rev2 yana ba da damar IMU tare da a
hade da BMI270 da BMM150 ICs don 9-axis ji.

Itace Power

Ana iya kunna allon ta hanyar haɗin USB, VIN, ko VUSB fil a kunne
kawunansu. Mafi ƙarancin shigarwa voltage don samar da wutar lantarki na USB an ƙayyade zuwa
tabbatar da aiki daidai.

Umarnin Amfani da samfur

1. Farawa

Don fara amfani da allo, bi waɗannan matakan:

IDE: Fara da Haɗin Ci gaba
Muhalli don shirye-shirye.
Arduino Cloud Editan: Yi amfani da tushen girgije
edita don dacewa da coding.

Arduino Cloud: Haɗa zuwa Arduino Cloud don
ƙarin ayyuka.

2. Connector Pinouts

Koma zuwa littafin mai amfani don cikakkun bayanai akan USB,
masu kai, da kuma cire masu haɗawa pinouts.

3. Aikin hukumar

Bincika sampda zane-zane, albarkatun kan layi, kuma koyi game da allo
hanyoyin dawowa.

4. Bayanin Injiniya

Fahimtar tsarin allo da ƙayyadaddun ramukan hawa
don haɗakar jiki.

FAQ (Tambayoyin da ake yawan yi)

Tambaya: Shin Nano 33 BLE Rev2 za a iya haɗa kai tsaye zuwa 5V
sigina?

A: A'a, hukumar tana goyan bayan 3.3VI/Os kawai kuma baya jurewa 5V.
Haɗin siginar 5V na iya lalata allon allo.

Tambaya: Ta yaya ake ba da wutar lantarki ga hukumar?

A: Ana iya kunna allon ta hanyar haɗin USB, VIN, ko VUSB fil
kan headers. Tabbatar da ingantaccen shigarwa voltage don kebul na USB.

View Fullscreen

Arduino® Nano 33 BLE Rev2
Bayanan Bayani na samfur SKU: ABX00071
Bayani
Arduino® Nano 33 BLE Rev2* ƙaƙƙarfan ƙaƙƙarfan tsari ne mai ƙunshe da tsarin NINA B306, bisa Nordic nRF52480 kuma yana ɗauke da Arm® Cortex®-M4F. BMI270 da BMM150 tare suna ba da 9-axis IMU. Za'a iya shigar da tsarin ko dai a matsayin bangaren DIP (lokacin da ake hawan fil) ko kuma a matsayin bangaren SMT, ana siyar da shi kai tsaye ta faifan castellated. * Nano 33 BLE Rev2 samfurin yana da SKUs guda biyu:
Ba tare da kai ba (ABX00071) Tare da kai (ABX00072)
Yankunan Target
Mai ƙirƙira, haɓakawa, aikace-aikacen IoT

1/15

Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

Arduino® Nano 33 BLE Rev2

Siffofin
NINA B306 Module
Mai sarrafawa
64 MHz Arm® Cortex®-M4F (tare da FPU) 1 MB Flash + 256 kB RAM
Bluetooth® 5 multiprotocol rediyo
2 Mbps CSA # 2 Talla ta Tsawon Tsawon Tsawon +8 dBm TX ikon -95 dBm hankali 4.8 mA a cikin TX (0 dBm) 4.6 mA a cikin RX (1 Mbps) Haɗin balun tare da fitowar 50 mai ƙarewa guda ɗaya IEEE 802.15.4 tallafin rediyo na Thread Zigbee®
Na'urorin haɗi
Cikakken-gudun 12 Mbps USB NFC-A tag Arm® CryptoCell CC310 tsarin tsaro QSPI/SPI/TWI/I²S/PDM/QDEC Babban gudun 32 MHz SPI Quad SPI interface 32 MHz EasyDMA don duk mu'amalar dijital 12-bit 200 ksps ADC 128 bit AES/ECB/CCM/AAR co-processor
BMI270 6-axis IMU (Accelerometer da Gyroscope)
16-bit 3-axis accelerometer tare da ± 2g / 4g / ± 8g / ± 16g kewayon 3-axis gyroscope tare da ± 125dps / ± 250dps / ± 500dps / ± 1000dps / ± 2000dps kewayon
BMM150 3-axis IMU (Magnetometer)
3-axis dijital geomagnetic firikwensin 0.3T ƙuduri ± 1300T (x, y-axis), ± 2500T (z-axis)
Saukewa: MP2322 DC
Yana daidaita shigar da voltage daga har zuwa 21V tare da mafi ƙarancin inganci na 65% @mafi ƙarancin inganci Fiye da inganci 85% @12V

2/15

Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

Arduino® Nano 33 BLE Rev2

Abubuwan da ke ciki

1 Hukumar

1.1 Ma'auni

1.1.1 Sharuɗɗan Aiki da aka Shawarar

1.2 Amfani da Wuta

2 Aiki Overview

2.1 Topology na allo

2.2 Mai sarrafawa

2.3 IMU

2.4 Itace Wuta

2.5 Toshe zane

3 Aikin hukumar

3.1 Farawa - IDE

3.2 Farawa - Arduino Cloud Editan

3.3 Farawa - Arduino Cloud

3.4 Sampda Sketches

3.5 Albarkatun Kan layi

3.6 farfadowa da na'ura

4 Mai Haɗa Pinouts

4.1 USB

4.2 Shugabanni

4.3 Gyara

5 Bayanan Injini

5.1 Shafi na allo da Ramukan Hawa

6 Takaddun shaida

6.1 Bayanin Daidaitawa CE DoC (EU)

6.2 Sanarwa na Daidaitawa ga EU RoHS & ISAUTAR 211 01/19/2021

6.3 Bayanin Ma'adinan Rikici

7 FCC Tsanaki

8 Bayanin Kamfanin

9 Takardun Magana

10 Tarihin Bita

3/15

Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

Arduino® Nano 33 BLE Rev2

1 Hukumar
Kamar yadda duk kwamitocin nau'ikan nau'ikan Nano, Nano 33 BLE Rev2 ba shi da cajar baturi amma ana iya yin aiki ta hanyar USB ko masu kai.
NOTE: Nano 33 BLE Rev2 kawai yana goyan bayan 3.3 VI/Os kuma baya jure wa 5V don haka da fatan ba a haɗa siginar V 5 kai tsaye zuwa wannan allo ko kuma ta lalace. Hakanan, sabanin sauran allunan Arduino Nano waɗanda ke goyan bayan aikin 5V, fil ɗin 5V BA ya samar da vol.tage amma an fi haɗa shi, ta hanyar jumper, zuwa shigar da wutar lantarki ta USB.
1.1 Ma'auni

1.1.1 Sharuɗɗan Aiki da aka Shawarar

Alama

Bayanin iyakoki na thermal Conservative ga dukkan hukumar:

1.2 Amfani da Wuta

Alamar PBL PLP PMAX

Bayanin Amfani da wutar lantarki tare da madauki mai aiki da ƙarfi Yawan wutar lantarki a cikin ƙananan yanayin wutar lantarki Maɗaukakin Wutar Lantarki

Min -40°C (40°F)

Matsakaicin 85°C (185°F)

Min Typ Max Unit

TBC

4/15

Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

2 Aiki Overview
2.1 Topology na allo
Sama:

Arduino® Nano 33 BLE Rev2

Topology top

Ref. Bayani: U1 NINA-B306 Module Bluetooth® Low Energy 5.0 Module U2 BMI270 Sensor IMU U7 BMM150 Magnetometer IC SJ5 VUSB Jumper
Kasa:

Ref. Bayanin U6 MP2322GQH Mai Saukar Mataki na Sauka PB1 IT-1185AP1C-160G-GTR Maɓallin Maɓalli DL1 Led L

5/15

Board topology bot Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

Arduino® Nano 33 BLE Rev2

Ref.

Bayani

SJ1

VUSB Jumper

SJ3

3v3 Jump

Ref.

Bayani

SJ2

D7 Jumper

SJ4

D8 Jumper

2.2 Mai sarrafawa
Babban Mai sarrafawa shine Arm® Cortex®-M4F wanda ke gudana har zuwa 64 MHz. Yawancin fil ɗin sa suna da haɗin kai zuwa masu kai na waje duk da haka wasu an tanadar su don sadarwa ta ciki tare da tsarin mara waya da na ciki na ciki I2C (IMU da Crypto).
NOTE: Sabanin sauran allunan Arduino Nano, fil A4 da A5 suna da abin cirewa na ciki da tsoho da za a yi amfani da su azaman I2C Bus don haka ba a ba da shawarar amfani da abubuwan shigar analog ba.

2.3 IMU
Nano 33 BLE Rev2 yana ba da damar IMU tare da 9-axis, ta hanyar haɗin BMI270 da BMM150 ICs. BMI270 ya haɗa da gyroscope mai axis guda uku da kuma na'urar accelerometer mai axis uku, yayin da BMM150 ke da ikon fahimtar bambancin filin maganadisu a cikin dukkan matakan uku. Za a iya amfani da bayanan da aka samu don auna ma'aunin motsi na ɗanyen motsi da kuma koyan na'ura.

2.4 Itace Wuta
Ana iya kunna allon ta hanyar haɗin USB, VIN ko VUSB fil akan masu kai.

Itacen wuta
NOTE: Tun da VUSB tana ciyar da VIN ta hanyar Schottky diode da mai sarrafa DC-DC ƙayyadaddun ƙaramar shigarwar vol.tage shine 4.5 V mafi ƙarancin wadata voltage daga kebul na USB dole ne a ƙara zuwa voltage a cikin kewayon tsakanin 4.8 V zuwa 4.96 V dangane da abin da ake zana na yanzu.

6/15

Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

2.5 Toshe zane

Arduino® Nano 33 BLE Rev2

Tsarin zane

7/15

Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

Arduino® Nano 33 BLE Rev2
3 Aikin hukumar
3.1 Farawa - IDE
Idan kana son shirya Nano 33 BLE Rev2 naka yayin da ba layi ba, kana buƙatar shigar da Arduino Desktop IDE [1] Don haɗa Nano 33 BLE Rev2 zuwa kwamfutarka, kuna buƙatar kebul na USB na Micro-B. Wannan kuma yana ba da iko ga allon, kamar yadda LED ya nuna.
3.2 Farawa - Arduino Cloud Editan
Duk allunan Arduino, gami da wannan, suna aiki a waje akan Arduino Cloud Editan [2], ta hanyar shigar da plugin ɗin kawai. An shirya Editan Cloud Cloud akan layi, saboda haka koyaushe zai kasance na zamani tare da sabbin abubuwa da goyan baya ga duk allunan. Bi [3] don fara codeing akan mashigin yanar gizo kuma loda zane-zanen ku akan allo.
3.3 Farawa - Arduino Cloud
Duk samfuran da aka kunna Arduino IoT ana tallafawa akan Arduino Cloud wanda ke ba ku damar shiga, tsarawa da tantance bayanan firikwensin, jawo abubuwan da suka faru, da sarrafa gidanku ko kasuwancin ku.
3.4 Sampda Sketches
SampZa a iya samun zane-zane na Nano 33 BLE Sense ko dai a cikin “Examples” menu a cikin Arduino IDE ko a cikin “Gina Examples” sashe na Arduino Docs website.
3.5 Albarkatun Kan layi
Yanzu da kuka bi ka'idodin abubuwan da zaku iya yi tare da hukumar zaku iya bincika damar da ba ta ƙarewa da take bayarwa ta hanyar duba ayyuka masu ban sha'awa akan Arduino Project Hub [4], Rubutun Laburaren Arduino [5] da kantin sayar da kan layi inda zaku so. iya cika allon ku da na'urori masu auna firikwensin, masu kunnawa da ƙari.

8/15

Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

Arduino® Nano 33 BLE Rev2
3.6 farfadowa da na'ura
Duk allunan Arduino suna da ginanniyar bootloader wanda ke ba da damar walƙiya allon ta USB. Idan zane ya kulle na'ura mai sarrafawa kuma allon ba zai iya zuwa ta hanyar USB ba, yana yiwuwa a shigar da yanayin bootloader ta danna maɓallin sake saiti sau biyu bayan kunna allon.
4 Mai Haɗa Pinouts

9/15

Pinout Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

Arduino® Nano 33 BLE Rev2

4.1 USB

Nau'in Ayyukan Pin

Bayani

1 VUSB

Ƙarfi

Shigar da Wutar Lantarki. Idan an kunna jirgin ta hanyar VUSB daga kan kai wannan fitarwa ne (1)

2 D-

Bambance-bambancen bayanan USB -

3 D+ ku

Bambance-bambancen bayanan banbancin USB +

ID 4

Analog

Yana Zaɓi Ayyukan Mai watsa shiri/Na'ura

5 GND

Ƙarfi

Power Ground

4.2 Shugabanni

Allon yana fallasa masu haɗin fil 15 guda biyu waɗanda za a iya haɗa su tare da fitilun kan layi ko kuma ana siyar da su ta hanyar castellated vias.

Nau'in Ayyukan Pin

1 d13

Dijital

2 + 3V3

Ikon Wuta

3 AREF

Analog

4 A0/DAC0 Analog

5 A1

Analog

6 A2

Analog

7 A3

Analog

8 A4/SDA Analog

9 A5/SCL Analog

10 A6

Analog

11 A7

Analog

12 VUSB

Wutar Shiga/Fita

13 RST

Dijital In

14 GND

Ƙarfi

15 VIN

Power In

16 TX

Dijital

17 RX

Dijital

18 RST

Dijital

19 GND

Ƙarfi

20 d2

Dijital

21 D3/PWM Dijital

22 d4

Dijital

23 D5/PWM Dijital

24 D6/PWM Dijital

25 d7

Dijital

26 d8

Dijital

27 D9/PWM Dijital

28 D10/PWM Dijital

29 D11/MOSI Digital

Bayanin GPIO Abubuwan da aka samar da wutar lantarki na ciki zuwa na'urorin waje Analog Reference; za a iya amfani dashi azaman GPIO ADC in/DAC out; za a iya amfani dashi azaman GPIO ADC a; za a iya amfani dashi azaman GPIO ADC a; za a iya amfani dashi azaman GPIO ADC a; za a iya amfani dashi azaman GPIO ADC a; I2C SDA; Ana iya amfani dashi azaman GPIO (1) ADC a cikin; I2C SCL; Ana iya amfani dashi azaman GPIO (1) ADC a cikin; za a iya amfani dashi azaman GPIO ADC a; za a iya amfani dashi azaman GPIO Kullum NC; za a iya haɗa shi da fil ɗin VUSB na mai haɗin USB ta hanyar ragewa jumper Active low sake saiti shigarwar (kwafin fil 18) Power Ground Vin Power shigar da USART TX; za a iya amfani dashi azaman GPIO USART RX; za a iya amfani da shi azaman GPIO Active low sake saiti shigarwar (kwafin fil 13) Power Ground GPIO GPIO; za a iya amfani dashi azaman PWM GPIO GPIO; ana iya amfani dashi azaman PWM GPIO, ana iya amfani dashi azaman PWM GPIO GPIO GPIO; za a iya amfani dashi azaman PWM GPIO; za a iya amfani dashi azaman PWM SPI MOSI; ana iya amfani dashi azaman GPIO

10/15

Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

Arduino® Nano 33 BLE Rev2

Nau'in Ayyukan Pin 30 D12/MISO Digital

Bayanin SPI MISO; ana iya amfani dashi azaman GPIO

4.3 Gyara

A gefen ƙasa na allon, a ƙarƙashin tsarin sadarwa, ana shirya siginonin ɓarna azaman 3 × 2 pads na gwaji tare da farar mil 100 tare da cire fil 4. Ana zana fil 1 a Hoto 3 Matsayin Mai Haɗi

Aikin Fil 1 +3V3 2 SWD 3 SWCLK 5 GND 6 RST

Buga Power Out Digital A cikin Power Digital In

Bayanin fitarwar wutar da aka samar a ciki don amfani da shi azaman voltage reference nRF52480 Single Wire Debug Data nRF52480 Single Wire Debug Clock Power Ground Mai aiki ƙaramar shigarwar sake saiti

5 Bayanan Injini
5.1 Shafi na allo da Ramukan Hawa
Matakan allon sun gauraya tsakanin awo da na sarki. Ana amfani da matakan daular don kula da grid mai nisan mil 100 tsakanin layuka na fil don ba su damar dacewa da allon biredi yayin da tsayin allo Metric ne.

11/15

Tsarin allo

Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

Arduino® Nano 33 BLE Rev2

6 Takaddun shaida

6.1 Bayanin Daidaitawa CE DoC (EU)
Muna ayyana ƙarƙashin alhakin mu kaɗai cewa samfuran da ke sama sun dace da mahimman buƙatun ƙa'idodin EU masu zuwa don haka sun cancanci tafiya cikin 'yanci a cikin kasuwannin da suka ƙunshi Tarayyar Turai (EU) da Yankin Tattalin Arziki na Turai (EEA).

6.2 Sanarwa na Daidaitawa ga EU RoHS & ISAUTAR 211 01/19/2021

Allolin Arduino suna bin umarnin RoHS 2 2011/65/EU na Majalisar Tarayyar Turai da RoHS 3 Directive 2015/863/EU na Majalisar 4 ga Yuni 2015 kan ƙuntata amfani da wasu abubuwa masu haɗari a cikin kayan lantarki da lantarki.

Abun Gubar (Pb) Cadmium (Cd) Mercury (Hg) Hexavalent Chromium (Cr6+) Poly Brominated Biphenyls (PBB) Poly Brominated Diphenyl ethers (PBDE) Bis (2-Ethylhexyl} phthalate (DEHP) Benzyl butyl phthalate (BBP) Dibut (BBP) DBP) Diisobutyl phthalate (DIBP)

Matsakaicin iyaka (ppm) 1000 100 1000 1000 1000 1000 1000 1000 1000 1000

Keɓancewa: Ba a da'awar keɓancewa.

Allunan Arduino sun cika cika buƙatun da ke da alaƙa na Dokokin Tarayyar Turai (EC) 1907/2006 game da Rijista, Ƙimar, Izini da Ƙuntata Sinadarai (ISA). Ba mu bayyana ko ɗaya daga cikin SVHCs ba (https://echa.europa.eu/)web/bako/Jerin-jerin-takara), Jerin Abubuwan Abubuwan da ke Damu da Babban Damuwa don izini a halin yanzu da ECHA ta fitar, yana nan a cikin duk samfuran (da kuma kunshin) a cikin adadi mai yawa a cikin maida hankali daidai ko sama da 0.1%. A iyakar saninmu, muna kuma bayyana cewa samfuranmu ba su ƙunshi kowane nau'in abubuwan da aka jera akan "Jerin Izini" (Annex XIV na ƙa'idodin REACH) da Abubuwan da ke da matukar damuwa (SVHC) a cikin kowane adadi mai mahimmanci kamar yadda aka ƙayyade. ta Annex XVII na jerin 'yan takara da ECHA (Hukumar Sinadarai ta Turai) ta buga 1907/2006/EC.

12/15

Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

Arduino® Nano 33 BLE Rev2
6.3 Bayanin Ma'adinan Rikici
A matsayin mai ba da kayayyaki na duniya na kayan lantarki da na lantarki, Arduino yana sane da wajibcinmu game da dokoki da ka'idoji game da Ma'adinan Rikici, musamman Dodd-Frank Wall Street Reform and Consumer Protection Act, Sashe na 1502. Arduino ba ya samo asali ko aiwatar da rikici kai tsaye. ma'adanai irin su Tin, Tantalum, Tungsten, ko Zinariya. Ma'adanai masu rikice-rikice suna ƙunshe a cikin samfuranmu a cikin nau'in solder ko a matsayin sashi a cikin kayan haɗin ƙarfe. A matsayin wani ɓangare na ƙwazonmu mai ma'ana, Arduino ya tuntuɓi masu samar da kayan aikin da ke cikin sarkar kayan mu don tabbatar da ci gaba da bin ƙa'idodin. Dangane da bayanan da muka samu zuwa yanzu mun bayyana cewa samfuranmu sun ƙunshi ma'adanai masu rikice-rikice waɗanda aka samo daga wuraren da babu rikici.
7 FCC Tsanaki
Duk wani canje-canje ko gyare-gyaren da ƙungiyar da ke da alhakin bin doka ba ta amince da su ba na iya ɓata ikon mai amfani na sarrafa kayan aiki. Wannan na'urar ta bi sashe na 15 na Dokokin FCC. Aiki yana ƙarƙashin sharuɗɗa biyu masu zuwa: (1) Wannan na'urar bazai haifar da tsangwama mai cutarwa ba (2) dole ne wannan na'urar ta karɓi duk wani tsangwama da aka samu, gami da tsangwama wanda zai iya haifar da aiki maras so. FCC RF Bayanin Bayyana Radiation:
1. Wannan Mai watsawa dole ne a kasance tare ko aiki tare da kowane eriya ko mai watsawa. 2. Wannan kayan aikin ya dace da iyakokin fiddawa na RF wanda aka tsara don yanayi mara sarrafawa. 3. Ya kamata a shigar da wannan kayan aiki da aiki tare da mafi ƙarancin nisa na 20cm tsakanin radiator &
jikinka.
Turanci: Littattafan mai amfani don na'urar rediyon da ba ta da lasisi za ta ƙunshi sanarwa mai zuwa ko makamancinta a cikin wani fili a cikin littafin jagorar mai amfani, a madadin na'urar ko duka biyun. Wannan na'urar ta dace da ma'auni(s) na RSS na masana'antar Kanada. Aiki yana ƙarƙashin sharuɗɗa biyu masu zuwa: (1) wannan na'urar bazai haifar da tsangwama ba (2) dole ne wannan na'urar ta karɓi kowane tsangwama, gami da tsangwama wanda zai iya haifar da aikin na'urar da ba a so. Faransanci: Le présent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils rediyo keɓe lasisi. L'exploitation est autorisée aux deux sharuddan suivantes: (1) l' appareil nedoit pas produire de brouillage (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, da brouillage est susceptible de'en . Gargaɗi na IC SAR: Turanci Ya kamata a shigar da wannan kayan aikin tare da mafi ƙarancin nisa na 20 cm tsakanin radiyo da jikinka.

13/15

Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

Arduino® Nano 33 BLE Rev2

Faransanci: Lors de l' shigarwa et de l' amfani de ce dispositif, la distance entre le radiateur et le corps est d'au moins 20 cm.

Muhimmi: Yanayin zafin aiki na EUT ba zai iya wuce 85 ba kuma kada ya kasance ƙasa da -40.

Ta haka, Arduino Srl ya bayyana cewa wannan samfurin ya dace da mahimman buƙatu da sauran tanadin da suka dace na Directive 2014/53/EU. An ba da izinin amfani da wannan samfurin a duk ƙasashe membobin EU.

Matsakaicin mita 863-870Mhz

Matsakaicin ikon fitarwa (ERP) TBD

8 Bayanin Kamfanin

Sunan kamfani Adireshin kamfani

Arduino Srl Ta Andrea Appiani 25 20900 MONZA Italiya

9 Takardun Magana

Reference Arduino IDE (Desktop) Arduino Cloud Editan Arduino Cloud Editan - Farawa Arduino Project Hub Reference Forum
Nina B306

Yanar Gizo https://www.arduino.cc/en/software https://create.arduino.cc/editor
https://docs.arduino.cc/arduino-cloud/guides/editor/
https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending https://www.arduino.cc/reference/en/ http://forum.arduino.cc/ https://content.u-blox.com/sites/default/files/NINA-B3_DataSheet_UBX17052099.pdf

14/15

Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

Arduino® Nano 33 BLE Rev2

10 Tarihin Bita

Date 25/04/2024 2024/02/21

Canje-canje Sabunta hanyar haɗi zuwa sabon Sakin Farko Editan Cloud

15/15

Arduino® Nano 33 BLE Rev2

An gyara: 13/06/2024

Takardu / Albarkatu

Arduino ABX00071 Karamin Girman Module [pdf] Littafin Mai shi
ABX00071, ABX00071 Karamin Girman Module, Karamin Girman Module, Girman Module, Module

Magana

Manual mai amfani

ABX00071 Karamin Girman Module

Ƙayyadaddun bayanai

Bayanin samfur

Aiki Ya Ƙareview

Cibiyar Topology

Mai sarrafawa

IMU

Itace Power

Umarnin Amfani da samfur

1. Farawa

2. Connector Pinouts

3. Aikin hukumar

4. Bayanin Injiniya

FAQ (Tambayoyin da ake yawan yi)

Tambaya: Shin Nano 33 BLE Rev2 za a iya haɗa kai tsaye zuwa 5V
sigina?

Tambaya: Ta yaya ake ba da wutar lantarki ga hukumar?

Takardu / Albarkatu

Magana

Bar sharhi

Soke amsa

ABX00071 Karamin Girman Module

Ƙayyadaddun bayanai

Bayanin samfur

Aiki Ya Ƙareview

Cibiyar Topology

Mai sarrafawa

IMU

Itace Power

Umarnin Amfani da samfur

1. Farawa

2. Connector Pinouts

3. Aikin hukumar

4. Bayanin Injiniya

FAQ (Tambayoyin da ake yawan yi)

Tambaya: Shin Nano 33 BLE Rev2 za a iya haɗa kai tsaye zuwa 5V sigina?

Tambaya: Ta yaya ake ba da wutar lantarki ga hukumar?

Takardu / Albarkatu

Magana

Labarai masu alaka

Bar sharhi

Soke amsa

Tambaya: Shin Nano 33 BLE Rev2 za a iya haɗa kai tsaye zuwa 5V
sigina?