ABX00071 Miniature Size module
“
Litlhaloso
- Sehlahisoa sa Reference Manual SKU: ABX00071
- Libaka tse reriloeng: Moetsi, lintlafatso, ts'ebeliso ea IoT
- E fetotsoe: 13/06/2024
Tlhahisoleseding ya Sehlahiswa
Sehlahisoa sena ke boto ea nts'etsopele e nang le tse latelang
Likaroloana:
- NINA B306 Module
- processor
- Lisebelisoa: BMI270 6-axis IMU (Accelerometer le Gyroscope),
BMM150 3-axis IMU (Magnetometer), MP2322 DC-DC regulator
E sebetsa hapeview
Board Topology
The topology ea boto e kenyelletsa likarolo tse kang MP2322GQH Mohato
Down Converter, konopo ea push, le LED.
processor
Boto e na le processor e nang le phini e khethehileng
ditshebetso. Lipini tsa A4 le A5 li khothaletsoa ts'ebeliso ea I2C Bus
ho e-na le lisebelisoa tsa analoge.
IMU
Nano 33 BLE Rev2 e fana ka bokhoni ba IMU ka
motsoako oa BMI270 le BMM150 ICs bakeng sa 9-axis sensing.
Sefate sa Matla
Boto e ka tsamaisoa ka sehokelo sa USB, VIN, kapa VUSB pin
lihlooho. Bonyane ba ho kenya letsohotage bakeng sa phepelo ea motlakase ea USB e hlalositsoe ho
netefatsa ts'ebetso e nepahetseng.
Litaelo tsa Tšebeliso ea Sehlahisoa
1. Ho Qala
Ho qala ho sebelisa boto, latela mehato ena:
- IDE: Qala ka Ntlafatso e Kopanetsoeng
Tikoloho bakeng sa mananeo. - Arduino Cloud Editor: Sebelisa marang-rang a marang-rang
mohlophisi bakeng sa boiketlo ba ho khouta. - Leru la Arduino: Hokela ho Arduino Cloud bakeng sa
mesebetsi e eketsehileng.
2. Li-pinouts tsa sehokelo
Sheba buka ea mosebelisi bakeng sa tlhaiso-leseling e batsi ka USB,
lihlooho, le li-pinouts tsa sehokelo sa debug.
3. Ts'ebetso ea Boto
Hlahloba sample sketches, lisebelisoa tsa marang-rang, le ho ithuta ka boto
mekhoa ea ho hlaphoheloa.
4. Boitsebiso ba Mechini
Utloisisa kemiso ea boto le litlhaloso tsa lesoba le ntseng le kenngoa
bakeng sa kopanyo ya mmele.
FAQ (Lipotso Tse Botsoang Hangata)
P: Na Nano 33 BLE Rev2 e ka hokeloa ka kotloloho ho 5V
lipontšo?
A: Che, boto e tšehetsa 3.3VI / Os feela mme ha e mamelle 5V.
Ho kopanya matšoao a 5V ho ka senya boto.
P: Matla a fanoa joang ho boto?
A: Boto e ka tsamaisoa ka sehokelo sa USB, VIN, kapa VUSB
ka lihlooho. Etsa bonnete ba hore ho na le molumo o nepahetseng oa molumotage bakeng sa phepelo ea USB.
"`
Arduino® Nano 33 BLE Rev2
Sehlahisoa sa Reference Manual SKU: ABX00071
Tlhaloso
Arduino® Nano 33 BLE Rev2* ke mojule oa boholo bo bonyenyane o nang le mojule oa NINA B306, o thehiloeng ho Nordic nRF52480 mme o na le Arm® Cortex®-M4F. BMI270 le BMM150 ka kopanelo li fana ka IMU ea 9-axis. Mojule o ka hlongoa joalo ka karolo ea DIP (ha o kenya lihlooho tsa pin) kapa joalo ka karolo ea SMT, o e kopanya ka kotloloho ka lipampiri tse nang le li-castelated. *Sehlahisoa sa Nano 33 BLE Rev2 se na le li-SKU tse peli:
Ntle le lihlooho (ABX00071) E nang le lihlooho (ABX00072)
Libaka tse reriloeng
Moetsi, lintlafatso, ts'ebeliso ea IoT
1 / 15
Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
Arduino® Nano 33 BLE Rev2
Likaroloana
NINA B306 Module
processor
64 MHz Arm® Cortex®-M4F (ka FPU) 1 MB Flash + 256 kB RAM
Bluetooth® 5 radio multiprotocol
2 Mbps CSA #2 Advertising Extensions Long Range +8 dBm TX power -95 dBm sensitivity 4.8 mA in TX (0 dBm) 4.6 mA ho RX (1 Mbps) Balun e kopantsoeng le tlhahiso ea 50 e le 'ngoe IEEE 802.15.4 radio Zige tšehetso® Thread Zige
Pheripherals
Lebelo le felletseng la 12 Mbps USB NFC-A tag Arm® CryptoCell CC310 security subsystem QSPI/SPI/TWI/I²S/PDM/QDEC Lebelo le phahameng 32 MHz SPI Quad SPI interface 32 MHz EasyDMA bakeng sa likhokahano tsohle tsa dijithale 12-bit 200 ksps ADC 128 bit AES/ECB/CCM/AAR co-processor
BMI270 6-axis IMU (Accelerometer le Gyroscope)
16-bit 3-axis accelerometer e nang le ±2g/±4g/±8g/±16g range 3-axis gyroscope e nang le ±125dps/±250dps/±500dps/±1000dps/±2000dps range
BMM150 3-axis IMU (Magnetometer)
3-axis digital geomagnetic sensor 0.3T resolution ±1300T (x,y-axis), ±2500T (z-axis)
MP2322 DC-DC
E laola tlhahiso ea molumotage ho tloha ho 21V ka bonyane ba 65% e sebetsang hantle @moroalo o fokolang Ho feta 85% e sebetsang hantle @12V
2 / 15
Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
Arduino® Nano 33 BLE Rev2
Litaba
1 Boto
4
1.1 Lintlha
4
1.1.1 Maemo a Tšebetso a khothalelitsoeng
4
1.2 Tšebeliso ea Matla
4
2 Functional Overview
5
2.1 Thutoloji ea Boto
5
2.2 processor
6
2.3 IMU
6
2.4 Sefate sa Matla
6
2.5 Setšoantšo sa Block
7
3 Ts'ebetso ea Boto
8
3.1 Ho qala – IDE
8
3.2 Ho qala – Arduino Cloud Editor
8
3.3 Ho qala - Arduino Cloud
8
3.4 Sample Sketches
8
3.5 Lisebelisoa tsa Marang-rang
8
3.6 Pholiso ea Boto
9
4 Li-pinouts tsa sehokelo
9
4.1 USB
10
4.2 Lihlooho
10
4.3 Debug
11
5 Litaba tsa Mechini
11
5.1 Kemiso ea Boto le Likoti tse Behang
11
6 Setifikeiti
12
6.1 Phatlalatso ea Conformity CE DoC (EU)
12
6.2 Phatlalatso ea Tumellano le EU RoHS & REACH 211 01/19/2021
12
6.3 Phatlalatso ea Liminerale tsa Khohlano
13
7 Tlhokomeliso ea FCC
13
8 Boitsebiso ba Khampani
14
9 Litokomane tsa Litšupiso
14
10 Nalane ea Phetoho
15
3 / 15
Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
Arduino® Nano 33 BLE Rev2
1 Boto
Joalo ka liboto tsohle tsa Nano form factor, Nano 33 BLE Rev2 ha e na tjhaja ea betri empa e ka tsamaisoa ka USB kapa lihlooho.
TLHOKOMELISO: Nano 33 BLE Rev2 e ts'ehetsa 3.3 VI/Os feela 'me HA E mamelle 5V kahoo ka kopo etsa bonnete ba hore ha o hokelle matšoao a 5 V ka kotloloho ho boto ena kapa e tla senyeha. Hape, ho fapana le liboto tse ling tsa Arduino Nano tse tšehetsang ts'ebetso ea 5 V, pinana ea 5V HA E fane ka vol.tage empa ho e-na le hoo e hokahane, ka jumper, ho kenya matla a USB.
1.1 Lintlha
1.1.1 Maemo a Tšebetso a khothalelitsoeng
Letšoao
Tlhaloso Meeli ea mocheso oa Conservative bakeng sa boto eohle:
1.2 Tšebeliso ea Matla
Letšoao la PBL PLP PMAX
Tlhaloso Tšebeliso ea matla e nang le loop e phathahaneng Tšebeliso ea matla ka mokhoa o fokolang oa matla Tšebeliso e phahameng ea Matla
Ka tlase ho -40 °C ( 40 °F)
Boholo ba 85 °C ( 185 °F)
Min Type Max Unit
TBC
mW
TBC
mW
TBC
mW
4 / 15
Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
2 Functional Overview
2.1 Thutoloji ea Boto
Holimo:
Arduino® Nano 33 BLE Rev2
Topology ea boto
Ref. Tlhaloso U1 NINA-B306 Mojule Bluetooth® Low Energy 5.0 Mojule U2 BMI270 Sensor IMU U7 BMM150 Magnetometer IC SJ5 VUSB Jumper
Tlase:
Ref. Tlhaloso U6 MP2322GQH Step Down Converter PB1 IT-1185AP1C-160G-GTR Push konopo DL1 Led L
5 / 15
Board topology bot Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
Arduino® Nano 33 BLE Rev2
Ref.
Tlhaloso
SJ1
VUSB jumper
SJ3
3v3 Jumper
Ref.
Tlhaloso
SJ2
D7 Jumper
SJ4
D8 Jumper
2.2 processor
Main processor ke Arm® Cortex®-M4F e mathang ho fihla ho 64 MHz. Boholo ba lithakhisa tsa eona li hokahane le lihlooho tsa ka ntle leha ho le joalo tse ling li boloketsoe puisano ea ka hare le module e se nang mohala le li-peripherals tsa I2C tse ka hare (IMU le Crypto).
TLHOKOMELISO: Ho fapana le liboto tse ling tsa Arduino Nano, lithakhisa tsa A4 le A5 li na le ho hula ka hare 'me tsa kamehla li tla sebelisoa e le I2C Bus kahoo ha ho khothalletsoe ho sebelisoa e le lisebelisoa tsa analog.
2.3 IMU
Nano 33 BLE Rev2 e fana ka bokhoni ba IMU ka 9-axis, ka motsoako oa BMI270 le BMM150 ICs. BMI270 e kenyelletsa gyroscope ea li-axis tse tharo hammoho le accelerometer ea li-axis tse tharo, ha BMM150 e khona ho lemoha phapang ea matla a khoheli likarolong tsohle tse tharo. Lintlha tse fumanoeng li ka sebelisoa bakeng sa ho lekanya mekhahlelo e tala ea motsamao hammoho le ho ithuta ka mochini.
2.4 Sefate sa Matla
Boto e ka tsamaisoa ka sehokelo sa USB, VIN kapa VUSB lithareng.
Sefate sa matla
ELA HLOKO: Kaha VUSB e fepa VIN ka Schottky diode le molaoli oa DC-DC o boletse bonyane ba matla a ho kenya.tage ke 4.5 V palo e tlase ea phepelotage ho tloha ho USB e tlameha ho eketseha ho ea ho voltage sebakeng se pakeng tsa 4.8 V ho isa ho 4.96 V ho latela hore na e huloa hona joale.
6 / 15
Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
2.5 Setšoantšo sa Block
Arduino® Nano 33 BLE Rev2
Setšoantšo se Thibeloang
7 / 15
Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
Arduino® Nano 33 BLE Rev2
3 Ts'ebetso ea Boto
3.1 Ho qala – IDE
Haeba u batla ho hlophisa Nano 33 BLE Rev2 ea hau ha u ntse u le sieo inthaneteng u hloka ho kenya Arduino Desktop IDE [1] Ho hokela Nano 33 BLE Rev2 komporong ea hau, u tla hloka thapo ea Micro-B ea USB. Sena se boetse se fana ka matla ho boto, joalokaha ho bontšitsoe ke LED.
3.2 Ho qala – Arduino Cloud Editor
Liboto tsohle tsa Arduino, ho kenyeletsoa le ena, li sebetsa ka ntle ho lebokose ho Arduino Cloud Editor [2], ka ho kenya plugin e bonolo feela. Arduino Cloud Editor e tsamaisoa inthaneteng, ka hona e tla lula e le morao-rao ka likarolo tsa morao-rao le tšehetso bakeng sa liboto tsohle. Latela [3] ho qala ho khouta sebatli le ho kenya litšoantšo tsa hau botong ea hau.
3.3 Ho qala - Arduino Cloud
Lihlahisoa tsohle tse nolofalitsoeng ke Arduino IoT li tšehelitsoe ho Arduino Cloud e u lumellang hore u kene, u kenye le ho sekaseka lintlha tsa sensor, ho qala liketsahalo, le ho iketsetsa ntlo kapa khoebo ea hau.
3.4 Sample Sketches
Sample sekeche sa Nano 33 BLE Sense se ka fumanoa ho "Examples" ho Arduino IDE kapa ho "Built-in Examples” karolo ea Arduino Docs websebaka.
3.5 Lisebelisoa tsa Marang-rang
Kaha joale u se u fetile linthong tsa motheo tsa seo u ka se etsang ka boto u ka hlahloba menyetla e sa feleng eo e fanang ka eona ka ho hlahloba merero e thabisang ho Arduino Project Hub [4], Arduino Library Reference [5] le lebenkele la inthanete moo u tla khona ho tlatselletsa boto ea hau ka li-sensor, li-actuator le tse ling.
8 / 15
Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
Arduino® Nano 33 BLE Rev2
3.6 Pholiso ea Boto
Liboto tsohle tsa Arduino li na le bootloader e hahelletsoeng ka hare e lumellang ho bonesa boto ka USB. Haeba sketch e notlela processor mme boto ha e sa fumaneha ka USB, hoa khoneha ho kenya mokhoa oa bootloader ka ho tlanya konopo ea reset hang ka mor'a ho matlafatsa boto.
4 Li-pinouts tsa sehokelo
9 / 15
Pinout Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
Arduino® Nano 33 BLE Rev2
4.1 USB
Mofuta oa Ts'ebetso ea Pin
Tlhaloso
1 VUSB
Matla
Kenyelletso ea Phepelo ea Matla. Haeba boto e tsamaisoa ka VUSB ho tloha hloohong sena ke Output (1)
2 D-
Lintlha tse fapaneng tse fapaneng tsa USB -
3D+
Lintlha tse fapaneng tsa phapang ea USB +
ID ea 4
Analoge
E khetha tšebetso ea Host/Device
5 GND
Matla
Sebaka sa Matla
4.2 Lihlooho
Boto e pepesa lihokelo tse peli tsa 15-pin tse ka kopanngoang ka lihlooho tsa phini kapa tsa rekisoa ka li-vias tse nang le li-castelated.
Mofuta oa Ts'ebetso ea Pin
1 D13
Dijithale
2 +3V3
Tlosa Matla
3 AREF
Analoge
4 A0/DAC0 Analog
5 A1
Analoge
6 A2
Analoge
7 A3
Analoge
8 Analoge ea A4/SDA
9 Analoge ea A5/SCL
10 A6
Analoge
11 A7
Analoge
12 VUSB
Matla ka hare/Kantle
13 RST
Digital In
14 GND
Matla
15 VIN
Power In
16 TX
Dijithale
17 RX
Dijithale
18 RST
Dijithale
19 GND
Matla
20 D2
Dijithale
21 D3/PWM Digital
22 D4
Dijithale
23 D5/PWM Digital
24 D6/PWM Digital
25 D7
Dijithale
26 D8
Dijithale
27 D9/PWM Digital
28 D10/PWM Digital
29 D11/MOSI Digital
Tlhaloso GPIO e hlahisoang ka hare ho matla ho lisebelisoa tsa ka ntle Reference Analog; e ka sebelisoa e le GPIO ADC ho / DAC kantle; e ka sebelisoa e le GPIO ADC ka; e ka sebelisoa e le GPIO ADC ka; e ka sebelisoa e le GPIO ADC ka; e ka sebelisoa e le GPIO ADC ka; I2C SDA; E ka sebelisoa e le GPIO (1) ADC ka; I2C SCL; E ka sebelisoa e le GPIO (1) ADC ka; e ka sebelisoa e le GPIO ADC ka; e ka sebelisoa e le GPIO Ka tloaelo NC; e ka hokeloa ho VUSB pin ea sehokelo sa USB ka ho khutsufatsa jumper Keletso e sebetsang e tlase ea reset (kopi ea pin 18) Power Ground Vin Power input USART TX; e ka sebelisoa e le GPIO UART RX; e ka sebelisoa e le GPIO Active low reset input (duplicate of pin 13) Power Ground GPIO GPIO; e ka sebelisoa e le PWM GPIO GPIO; e ka sebelisoa e le PWM GPIO, e ka sebelisoa e le PWM GPIO GPIO GPIO; e ka sebelisoa e le PWM GPIO; e ka sebelisoa e le PWM SPI MOSI; e ka sebelisoa e le GPIO
10 / 15
Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
Arduino® Nano 33 BLE Rev2
Mofuta oa Ts'ebetso ea Pin 30 D12/MISO Digital
Tlhaloso SPI MISO; e ka sebelisoa e le GPIO
4.3 Debug
Ka lehlakoreng le ka tlase la boto, tlas'a mojule oa puisano, matšoao a debug a hlophisitsoe joalo ka lipampiri tsa liteko tsa 3 × 2 tse nang le 100 mil pitch e nang le pin 4 e tlositsoeng. Pin 1 e bonts'itsoe ho Figure 3 Connector Positions
Pin Function 1 +3V3 2 SWD 3 SWCLK 5 GND 6 RST
Type Power Out Digital In Power Digital In
Tlhaloso: Matla a hlahisoang ka hare a tla sebelisoa e le voltage referense nRF52480 Single Wire Debug Data nRF52480 Single Wire Debug Clock Power Ground E sebetsang ho seta bocha bocha
5 Litaba tsa Mechini
5.1 Kemiso ea Boto le Likoti tse Behang
Mehato ea boto e tsoakane pakeng tsa metric le imperial. Mehato ea borena e sebelisoa ho boloka 100 mil pitch grid pakeng tsa mela ea phini ho e lumella ho lekana le boto athe bolelele ba boto ke Metric.
11 / 15
Sebopeho sa boto
Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
Arduino® Nano 33 BLE Rev2
6 Setifikeiti
6.1 Phatlalatso ea Conformity CE DoC (EU)
Re phatlalatsa tlas'a boikarabelo ba rona hore lihlahisoa tse ka holimo li lumellana le litlhoko tsa bohlokoa tsa Litaelo tse latelang tsa EU 'me kahoo li tšoaneleha bakeng sa ho tsamaea ka bolokolohi ka har'a limmaraka tse kenyeletsang European Union (EU) le European Economic Area (EEA).
6.2 Phatlalatso ea Tumellano le EU RoHS & REACH 211 01/19/2021
Liboto tsa Arduino li lumellana le RoHS 2 Directive 2011/65/EU ea Paramente ea Europe le RoHS 3 Directive 2015/863/EU ea Lekhotla la 4 Phuptjane 2015 mabapi le thibelo ea tšebeliso ea lintho tse ling tse kotsi ho lisebelisoa tsa motlakase le tsa elektroniki.
Substance Lead (Pb) Cadmium (Cd) Mercury (Hg) Hexavalent Chromium (Cr6+) Poly Brominated Biphenyls (PBB) Poly Brominated Diphenyl ethers (PBDE) Bis(2-Ethylhexyl} phthalate (DEHP) Benzyl butyl phthalate BP Diphenyl (Bphthalate) DBP) Diisobutyl phthalate (DIBP)
Boholo ba moeli (ppm) 1000 100 1000 1000 1000 1000 1000 1000 1000 1000
Litokoloho: Ha ho litokollo tse batloang.
Liboto tsa Arduino li lumellana ka botlalo le litlhoko tse amanang le European Union Regulation (EC) 1907 / 2006 mabapi le Ngoliso, Tlhahlobo, Tumello le Thibelo ea Lik'hemik'hale (REACH). Ha re phatlalatse leha e le efe ea SVHCs (https://echa.europa.eu/web/moeti/lethathamo la moeti), Lethathamo la Bakhethoa ba Matšoenyeho a Phahameng ka ho Fetisisa bakeng sa tumello e lokollotsoeng hajoale ke ECHA, le teng lihlahisoa tsohle (le sephutheloana) ka bongata bo lekanang le mahloriso a lekanang kapa a ka holimo ho 0.1%. Ho latela tsebo ea rona, re boetse re phatlalatsa hore lihlahisoa tsa rona ha li na letho la lintho tse thathamisitsoeng ho "Authorization List" (Annex XIV ea melaoana ea REACH) le Substances of Very High Concern (SVHC) ka chelete efe kapa efe ea bohlokoa joalo ka ha ho boletsoe. ka Sehlomathiso sa XVII sa Lethathamo la Bakhethoa le hatisitsoeng ke ECHA (European Chemical Agency) 1907 /2006/EC.
12 / 15
Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
Arduino® Nano 33 BLE Rev2
6.3 Phatlalatso ea Liminerale tsa Khohlano
Joaloka mofani oa lefats'e oa likarolo tsa elektronike le motlakase, Arduino e tseba boitlamo ba rona mabapi le melao le melaoana e mabapi le Conflict Minerals, haholo-holo Dodd-Frank Wall Street Reform le Consumer Protection Act, Karolo ea 1502. Arduino ha e hlahise ka ho toba kapa ha e sebetsane le likhohlano liminerale tse kang Tin, Tantalum, Tungsten, kapa Khauta. Liminerale tsa likhohlano li fumaneha lihlahisoa tsa rona ka mokhoa oa solder kapa e le karolo ea li-alloys tsa tšepe. E le karolo ea boikitlaetso ba rona bo loketseng, Arduino e ikopanye le bafani ba thepa ka har'a ketane ea rona ea phepelo ho netefatsa hore ba tsoela pele ho latela melao. Ho latela lintlha tse fumanoeng ho tla fihlela joale, re phatlalatsa hore lihlahisoa tsa rona li na le Liminerale tsa Likhohlano tse tsoang libakeng tse se nang likhohlano.
7 Tlhokomeliso ea FCC
Liphetoho life kapa life tse sa amoheloeng ka kotloloho ke mokha o ikarabellang bakeng sa tumellano li ka hlakola matla a mosebelisi a ho sebelisa sesebelisoa. Sesebelisoa sena se lumellana le karolo ea 15 ea Melao ea FCC. Ts'ebetso e ipapisitse le maemo a mabeli a latelang: (1) Sesebelisoa sena se kanna sa se ke sa baka tšitiso e kotsi (2) sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe e amohetsoeng, ho kenyelletsa le tšitiso e ka bakang ts'ebetso e sa batleheng. Polelo ea Ts'oaetso ea Mahlaseli a FCC RF:
1. Transmitter ena ha ea lokela ho ba sebakeng se le seng kapa ho sebetsa mmoho le lenakana lefe kapa lefe kapa transmitter. 2. Sesebelisoa sena se lumellana le meeli ea ho pepeseha ha mahlaseli a RF e behiloeng bakeng sa tikoloho e sa laoleheng. 3. Thepa ena e lokela ho kenngoa le ho sebetsoa ka sebaka sa bonyane 20cm pakeng tsa radiator le
mmele wa hao.
Sesotho: Libukana tsa mosebelisi bakeng sa lisebelisoa tsa radio tse sa lumelloeng ke laesense li tla ba le tsebiso e latelang kapa e ts'oanang sebakeng se hlakileng bukeng ea mosebelisi, ho fapana le sesebelisoa kapa ka bobeli. Sesebediswa sena se dumellana le ditekanyetso tsa RSS tse sa dumelleng laesense ya Industry Canada. Ts'ebetso e ipapisitse le maemo a mabeli a latelang: (1) sesebelisoa sena se kanna sa se ke sa baka tšitiso (2) sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe, ho kenyelletsa le tšitiso e ka bakang ts'ebetso e sa batleheng ea sesebelisoa. Sefora: Le présent appareil est conforme aux CNR d'Industrie Canada e sebetsang kapa appareils radio exempt de lacence. L'exploitation est autorisée aux deux conditions suivantes : (1) l' appareil nedoit pas produire de brouillage (2) l'utilisateur de l'appareil doit receiver tout brouillage radioélectrique subi, même si le brouillage est est . Tlhokomeliso ea IC SAR: Sesotho Thepa ena e lokela ho kengoa le ho sebetsoa ka sebaka sa bonyane 20 cm lipakeng tsa radiator le 'mele oa hau.
13 / 15
Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
Arduino® Nano 33 BLE Rev2
Sefora: Lors de l' installation et de l' exploitation de ce dispositif, la distance entre le radiateur et le corps est d 'au moins 20 cm.
Bohlokoa: Thempereichara ea ts'ebetso ea EUT e ke ke ea feta 85 mme ha ea lokela ho ba ka tlase ho -40.
Ka hona, Arduino Srl e phatlalatsa hore sehlahisoa sena se lumellana le litlhoko tsa bohlokoa le lipehelo tse ling tse amehang tsa Directive 2014/53/EU. Sehlahisoa sena se lumelletsoe ho sebelisoa linaheng tsohle tsa litho tsa EU.
Maqhubu a maqhubu 863-870Mhz
Maximum output power (ERP) TBD
8 Boitsebiso ba Khampani
Lebitso la Khamphani Aterese ea Khampani
Arduino Srl Via Andrea Appiani 25 20900 MONZA Italy
9 Litokomane tsa Litšupiso
Reference Arduino IDE (Desktop) Arduino Cloud Editor Arduino Cloud - Ho Qala Arduino Project Hub Library Reference Forum
Kena B306
Sehokelo https://www.arduino.cc/en/software https://create.arduino.cc/editor
https://docs.arduino.cc/arduino-cloud/guides/editor/
https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending https://www.arduino.cc/reference/en/ http://forum.arduino.cc/ https://content.u-blox.com/sites/default/files/NINA-B3_DataSheet_UBX17052099.pdf
14 / 15
Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
Arduino® Nano 33 BLE Rev2
10 Nalane ea Phetoho
Date 25/04/2024 2024/02/21
Liphetoho Sehokelo se ntlafalitsoeng sa Tokollo ea Pele ea Cloud Editor
15 / 15
Arduino® Nano 33 BLE Rev2
E fetotsoe: 13/06/2024
Litokomane / Lisebelisoa
 |
Arduino ABX00071 Miniature Sized Module [pdf] Buka ea Mong'a ABX00071, ABX00071 Miniature Siized Module, Miniature Siized Module, Siized Module, Module |
