HALO HAFH-RF Fa'atonu Fa'amaumau Maualuluga Fa'afo'i Fa'alava
Fa'amatalaga
- Igoa o oloa: Halo Static Return Frame
- Fa'ata'ita'iga Va'aiga: HAFH-RF, HAFH-SF
- Vaega e aofia ai:
- laulau vae x1
- Koluma x1
- Fa'amau: M6x12 x2
- Faovilivili: ST4x20 x13
- Fa puipui itu x1
- Pa'u pa x10
- Fa'avaa pito i luga-1 x1
- Fa'amau: M6x10 x3
- puipui ogatotonu x1
- Ala o le ogatotonu x2
- Fa'avaa pito i luga-2 x1
- Fa'amau lima M6x10 x2
- Allen Wrench(4mm) x1
- Allen Wrench(5mm) x1
- Nonoa uaea x2
Ua umaview
Vaega vaega
Faatonuga Fonotaga
Laasaga 1
- Loosen the pre-installed bolts and Adjust the length of the top frame to match the size of thetabletop.
Laasaga 2
- Inset the Column to the top frame,fix column with 4pcs screws M6x12 like.
Laasaga 3
- Tuu vae laulau i luga o le koluma ma feliuliua'i ma fa'aoga lelei, ona fa'amau lea o le fa'amau na fa'apipi'i muamua.
Laasaga 4
- Tuu le puipui o le itu i luga o le faavaa pito i luga ma faʻamau faʻamau.
Laasaga 5
- Fa'afeso'ota'i le fa'avaa fa'afo'i i le fale faigaluega e tasi ma fa'amau i fa'amau lima e 2.
- Fa'amau fa'amau fa'amau fa'atasi ma 2pcs sikulima M6x10.
Laasaga 6
- Fa'amau i luga ole laulau ma fa'apipi'i ile 24 pcs sikulima ST4x20;
- Fa'amau le fa'amau fa'amaufa'atasi ma 2 pcs sikulima M6x10
Fa'apipi'i fata uaea
Laasaga 1
- Fix the cable tray(B2-SSCT ) to the cable tray arms(HP-SSARM) with 8 pcs M6x10 screws.
Laasaga 2
- Fa'apipi'i fa'amau U i luga o le fa'avaa o le kesi fa'atasi ai ma sikulima 4 pcs M8x10.
- Fa'ae'e le fata uaea i le fa'avaa o le kesi ma fa'apipi'i i fa'amau 6 pcs M6x10
Fa'apipi'iina o le laulau ( Shush30 Privacy Screen )
Laasaga 1
- Insert the tapped plates to the screen panel ( plates can be found in B2-SBRAC carton)
Laasaga 2
- Install the screen brackets ( B2-SBRAC )to the Shush30 Extrusion with 8 pcs M5x6 screws.
Laasaga 3
- Fa'apipi'i puipui puipui (B2-SBRAC) i le fa'avaa o le kesi ma 10 pcs M6x10 sikulima.
EPS ( 900mm H Eco Panel ) Fa'apipi'iina o mata
Laasaga 1
- Install the screen brackets(B2-SBRAC) on the cable tray arm (B2-SSARM)with 10 PCS M6x10Screws- Place 8 x Double Ended Bolts M5* 32mm – 6mm through The screen bracket ( B2-SBRAC) holesandthe holes you have created in the Eco Panel Screen. Tighten double ended bolt with AllenkeyThe brackets direction as photos display.
Laasaga 2
- Place the EPS panel on the screen brackets Using a 6mm drill bit ( not included ), drill out holes in Eco Panel Screen in line with back to back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel )
- Tuu 8 x Fa'ai'u Fa'alua Bolts M5* 32mm – 6mm e ala ile puipui puipui ( B2-SBRAC ) pu ma pu na e faia i le Eco Panel Screen. Fa'amau fa'amau fa'aiu fa'alua fa'atasi ma le ki Allen.
FAQs
How many components are included in the Halo Static Return Frame?
The Halo Static Return Frame includes various components such as table feet, columns, bolts, screws, side brackets, rubber pads, top frames, hand bolts, Allen wrenches, and cable ties.
How do I install the cable tray on the desk frame?
To install the cable tray, first fix it to the cable tray arms using provided screws M6x10. Then, attach U brackets to the desk frame with screws M8x10 and mount the cable tray, securing it with screws M6x10.
What is required for installing the Eco Panel Screen?
Installing the Eco Panel Screen requires screen brackets, double-ended bolts, a drill bit (not included), and a suitable Allen key for tightening.
Pepa / Punaoa
 |
HALO HAFH-RF Fa'atonu Fa'amaumau Maualuluga Fa'afo'i Fa'alava [pdf] Tusi Taiala HAFH-RF, HAFH-RF Fa'a'a'aa'a Fa'afo'i Maualuluga Maualuluga |