Qafas ta' Ritorn b'Għoli Fiss Statiku HALO HAFH-RF

Speċifikazzjonijiet

• Isem tal-Prodott: Halo Static Return Frame
• Varjanti tal-Mudell: HAFH-RF, HAFH-SF
• Komponenti Inklużi:
  • Saqajn tal-mejda x1
  • Kolonna x1
  • Bolt: M6x12 x2
  • Kamin: ST4x20 x13
  • Parentesi tal-ġenb x1
  • Kuxxinett tal-gomma x10
  • Qafas ta' fuq-1 x1
  • Bolt: M6x10 x3
  • Bracket taċ-ċentru x1
  • Binarji ċentrali x2
  • Qafas ta' fuq-2 x1
  • Boltijiet tal-idejn M6x10 x2
  • Ċavetta Allen (4mm) x1
  • Ċavetta Allen (5mm) x1
  • Cable tie x2

Fuqview

Partijiet komponenti

Istruzzjonijiet ta' Armar

Pass 1

• Loosen the pre-installed bolts and Adjust the length of the top frame to match the size of thetabletop.

Pass 2

• Inset the Column to the top frame,fix column with 4pcs screws M6x12 like.

Pass 3

• Poġġi s-saqajn tal-mejda fuq il-kolonna u dawwarha u allinjaha, imbagħad issikka l-bolt installat minn qabel.

Pass 4

• Poġġi l-parentesi tal-ġenb fuq il-qafas ta' fuq u ssikka l-boltijiet.

Pass 5

• Qabbad il-qafas tar-ritorn mal-istazzjon tax-xogħol wieħed u ffissat b'2 boltijiet tal-idejn.
• Waħħal il-parentesi taċ-ċentru b'viti 2pcs M6x10.

Pass 6

• Immonta l-wiċċ tal-mejda u waħħalha b'24 biċċa viti ST4x20;
• Waħħal il-parentesi taċ-ċentru b'żewġ viti M2x6

Installazzjoni ta 'trej tal-kejbil

Pass 1

• Fix the cable tray(B2-SSCT ) to the cable tray arms(HP-SSARM) with 8 pcs M6x10 screws.

Pass 2

• Installa l-parentesi U mal-qafas tal-iskrivanija b'4 pcs M8x10 viti.
• Immonta t-trej tal-kejbil mal-qafas tal-iskrivanija u waħħalha b'6 pcs viti M6x10

Installazzjoni ta' panell tal-iskrin (Shush30 Privacy Screen)

Pass 1

• Insert the tapped plates to the screen panel ( plates can be found in B2-SBRAC carton)

Pass 2

• Install the screen brackets ( B2-SBRAC )to the Shush30 Extrusion with 8 pcs M5x6 screws.

Pass 3

• Waħħal il-parentesi tal-iskrin (B2-SBRAC) mal-qafas tal-iskrivanija b'10 viti M6x10.

Installazzjoni ta' pannell tal-iskrin tal-EPS (900mm H Eco Panel)

Pass 1

• Install the screen brackets(B2-SBRAC) on the cable tray arm (B2-SSARM)with 10 PCS M6x10Screws- Place 8 x Double Ended Bolts M5* 32mm – 6mm through The screen bracket ( B2-SBRAC) holesandthe holes you have created in the Eco Panel Screen. Tighten double ended bolt with AllenkeyThe brackets direction as photos display.

Pass 2

• Place the EPS panel on the screen brackets Using a 6mm drill bit ( not included ), drill out holes in Eco Panel Screen in line with back to back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel )
• Poġġi 8 x Boltijiet b'Tarf Doppju M5* 32mm – 6mm mit-toqob tal-bracket tal-iskrin (B2-SBRAC) u t-toqob li ħloqt fl-Iskrin tal-Eco Panel. Issikka l-bolt b'tarf doppju b'ċavetta Allen.

FAQs

How many components are included in the Halo Static Return Frame?

The Halo Static Return Frame includes various components such as table feet, columns, bolts, screws, side brackets, rubber pads, top frames, hand bolts, Allen wrenches, and cable ties.

How do I install the cable tray on the desk frame?

To install the cable tray, first fix it to the cable tray arms using provided screws M6x10. Then, attach U brackets to the desk frame with screws M8x10 and mount the cable tray, securing it with screws M6x10.

What is required for installing the Eco Panel Screen?

Installing the Eco Panel Screen requires screen brackets, double-ended bolts, a drill bit (not included), and a suitable Allen key for tightening.

Dokumenti / Riżorsi

Qafas ta' Ritorn b'Għoli Fiss Statiku HALO HAFH-RF [pdfManwal tal-Istruzzjonijiet HAFH-RF, HAFH-RF Qafas ta' Ritorn b'Għoli Fiss Statiku, Qafas ta' Ritorn b'Għoli Fiss Statiku, Qafas ta' Ritorn b'Għoli Fiss, Qafas ta' Ritorn b'Għoli

Referenzi

• Manwal għall-Utent