Halo Static Return Frame Instruction Manual

Product Identification

This document provides assembly and installation instructions for the Halo Static Return Frame. It covers two main configurations:

Halo Static Fixed Height Return Frame (HAFH-RF)

Halo Static Single Sided Fixed Height Workstation Frame (HAFH-SF)

Diagram Description: A line drawing illustrates the L-shaped frame structure. Arrows point to labels identifying the "Halo Static Fixed Height Return Frame (HAFH-RF)" and the "Halo Static Single Sided Fixed Height Workstation Frame (HAFH-SF)".

Component Parts

Diagram Description: An exploded view shows the various components of the desk frame with numbered callouts.

Assembly Instructions

Step 1: Adjust Top Frame Length

Loosen the pre-installed bolts and adjust the length of the top frame to match the size of the table top.

Diagram Description: Two views of the frame. One shows a close-up of bolts being loosened. The other shows the frame extending or retracting, indicated by arrows showing movement left and right.

Step 2: Attach Column

Inset the Column into the top frame and fix it with 4 pieces of M6x12 screws.

Diagram Description: Shows a column being inserted into the top frame. A magnified view highlights the attachment points and screws.

Step 3: Attach Table Feet

Place the table feet onto the column, rotate to align, and then tighten the pre-installed bolt.

Diagram Description: Shows a table foot being placed on the column base. A magnified view shows the bolt being tightened. The entire assembly (column attached to frame, with feet) is shown.

Step 4: Attach Side Brackets

Place the side bracket on the top frame and tighten the bolts.

Diagram Description: Shows a side bracket being positioned on the top frame. A magnified view highlights the bolt attachment. The assembly with column and feet is shown.

Step 5: Connect Return Frame and Fix Brackets

Connect the return frame to the single workstation and secure with 2 hand bolts. Fix the centre brackets with 2 pieces of M6x10 screws.

Diagram Description: Shows the L-shaped configuration being formed by connecting the return frame to the main workstation frame. Callouts indicate where hand bolts and centre bracket screws are applied.

Step 6: Mount Tabletop

Mount the tabletop and fix it with 24 pieces of ST4x20 screws. Fix the centre bracket with 2 pieces of M6x10 screws.

Diagram Description: Shows the tabletop being placed onto the assembled frame. Callouts indicate the locations for the 24 screws and the centre bracket screws.

Cable Tray Installation

Step 1: Attach Cable Tray to Arms

Fix the cable tray (B2-SSCT) to the cable tray arms (HP-SSARM) using 8 pieces of M6x10 screws.

Diagram Description: Shows the cable tray being attached to the arms with screws.

Step 2: Mount Cable Tray to Desk Frame

Install the U brackets to the desk frame with 4 pieces of M8x10 screws. Mount the cable tray to the desk frame and fix it with 6 pieces of M6x10 screws.

Diagram Description: Shows U brackets being attached to the desk frame, followed by the cable tray being mounted and secured with screws.

Screen Panel Installation (Shush30 Privacy Screen)

Step 1: Insert Tapped Plates

Insert the tapped plates into the screen panel. These plates can be found in the B2-SBRAC carton.

Diagram Description: A close-up view shows tapped plates being inserted into the edge of a screen panel.

Step 2: Attach Screen Brackets to Extrusion

Install the screen brackets (B2-SBRAC) to the Shush30 Extrusion using 8 pieces of M5x6 screws.

Diagram Description: Shows screen brackets being attached to the vertical extrusion of the screen panel. A magnified view details the screw placement.

Step 3: Fix Screen Brackets to Desk Frame

Fix the screen brackets (B2-SBRAC) to the desk frame using 10 pieces of M6x10 screws.

Diagram Description: Shows the assembled screen panel (with brackets attached to extrusion) being connected to the main desk frame using screws.

EPS (900mm H Eco Panel) Screen Panel Installation

Step 1: Install Screen Brackets on Cable Tray Arm

Install the screen brackets (B2-SBRAC) on the cable tray arm (B2-SSARM) using 10 pieces of M6x10 screws. The bracket direction should be as shown in the photos.

Diagram Description: Shows screen brackets being attached to the cable tray arm.

Step 2: Mount EPS Panel

Place the EPS panel onto the screen brackets. Using a 6mm drill bit (not included), drill holes in the Eco Panel Screen in line with the back-to-back screen bracket holes. Note: Carbide Drill Bits Work Best For PET panel. Place 8 x Double Ended Bolts (M5*32mm - 6mm) through the screen bracket (B2-SBRAC) holes and the newly drilled holes in the Eco Panel Screen. Tighten the double-ended bolts with an Allen key.

Diagram Description: Shows the EPS panel being placed on the brackets. A magnified view illustrates drilling holes and then inserting double-ended bolts through the bracket and panel, with an Allen key shown for tightening.