HALO HAFH-RF Static Fixed Height Return Frame
Specifications
- Product Name: Halo Static Return Frame
- Model Variants: HAFH-RF, HAFH-SF
- Components Included:
- Table feet x1
- Column x1
- Bolt: M6x12 x2
- Screw: ST4x20 x13
- Side brackets x1
- Rubber pad x10
- Top frame-1 x1
- Bolt: M6x10 x3
- Centre bracket x1
- Center rails x2
- Top frame-2 x1
- Hand bolts M6x10 x2
- Allen Wrench(4mm) x1
- Allen Wrench(5mm) x1
- Cable tie x2
Overview
Component parts
Assembly Instructions
Step 1
- Loosen the pre-installed bolts and Adjust the length of the top frame to match the size of thetabletop.
Step 2
- Inset the Column to the top frame,fix column with 4pcs screws M6x12 like.
Step 3
- Place the table feet on the column and rotate it and make it align, then tighten the pre-installed bolt.
Step 4
- Place the side bracket on the top frame and tighten the bolts.
Step 5
- Connect the return frame to the single workstation and fixed with 2 hand bolts.
- Fix the centre brackets with 2pcs screws M6x10.
Step 6
- Mount the tabletop and fix it with24 pcs screws ST4x20;
- Fix the centre bracket with 2 pcs screws M6x10
Cable tray installation
Step 1
- Fix the cable tray(B2-SSCT ) to the cable tray arms(HP-SSARM) with 8 pcs M6x10 screws.
Step 2
- Install the U brackets to the desk frame with 4 pcs M8x10 screws.
- Mount the cable tray to the desk frame and fix it with 6 pcs M6x10 screws
Screen panel installation ( Shush30 Privacy Screen )
Step 1
- Insert the tapped plates to the screen panel ( plates can be found in B2-SBRAC carton)
Step 2
- Install the screen brackets ( B2-SBRAC )to the Shush30 Extrusion with 8 pcs M5x6 screws.
Step 3
- Fix the screen brackets ( B2-SBRAC ) to the desk frame with 10 pcs M6x10 screws.
EPS ( 900mm H Eco Panel ) Screen panel installation
Step 1
- Install the screen brackets(B2-SBRAC) on the cable tray arm (B2-SSARM)with 10 PCS M6x10Screws- Place 8 x Double Ended Bolts M5* 32mm – 6mm through The screen bracket ( B2-SBRAC) holesandthe holes you have created in the Eco Panel Screen. Tighten double ended bolt with AllenkeyThe brackets direction as photos display.
Step 2
- Place the EPS panel on the screen brackets Using a 6mm drill bit ( not included ), drill out holes in Eco Panel Screen in line with back to back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel )
- Place 8 x Double Ended Bolts M5* 32mm – 6mm through The screen bracket ( B2-SBRAC ) holes and the holes you have created in the Eco Panel Screen. Tighten double ended bolt with Allen key.
FAQs
How many components are included in the Halo Static Return Frame?
The Halo Static Return Frame includes various components such as table feet, columns, bolts, screws, side brackets, rubber pads, top frames, hand bolts, Allen wrenches, and cable ties.
How do I install the cable tray on the desk frame?
To install the cable tray, first fix it to the cable tray arms using provided screws M6x10. Then, attach U brackets to the desk frame with screws M8x10 and mount the cable tray, securing it with screws M6x10.
What is required for installing the Eco Panel Screen?
Installing the Eco Panel Screen requires screen brackets, double-ended bolts, a drill bit (not included), and a suitable Allen key for tightening.
Documents / Resources
 |
HALO HAFH-RF Static Fixed Height Return Frame [pdf] Instruction Manual HAFH-RF, HAFH-RF Static Fixed Height Return Frame, Static Fixed Height Return Frame, Fixed Height Return Frame, Height Return Frame |