HALO HAFH-RF Static Fixed Height Return Frame
ਨਿਰਧਾਰਨ
- ਉਤਪਾਦ ਦਾ ਨਾਮ: Halo Static Return Frame
- ਮਾਡਲ ਰੂਪ: HAFH-RF, HAFH-SF
- ਭਾਗ ਸ਼ਾਮਲ:
- Table feet x1
- ਕਾਲਮ x1
- ਬੋਲਟ: M6x12 x2
- ਪੇਚ: ST4x20 x13
- Side brackets x1
- Rubber pad x10
- Top frame-1 x1
- ਬੋਲਟ: M6x10 x3
- Centre bracket x1
- Center rails x2
- Top frame-2 x1
- Hand bolts M6x10 x2
- Allen Wrench(4mm) x1
- Allen Wrench(5mm) x1
- ਕੇਬਲ ਟਾਈ x2
ਵੱਧview
ਕੰਪੋਨੈਂਟ ਹਿੱਸੇ
ਅਸੈਂਬਲੀ ਨਿਰਦੇਸ਼
ਕਦਮ 1
- Loosen the pre-installed bolts and Adjust the length of the top frame to match the size of thetabletop.
ਕਦਮ 2
- Inset the Column to the top frame,fix column with 4pcs screws M6x12 like.
ਕਦਮ 3
- Place the table feet on the column and rotate it and make it align, then tighten the pre-installed bolt.
ਕਦਮ 4
- ਸਾਈਡ ਬਰੈਕਟ ਨੂੰ ਉੱਪਰਲੇ ਫਰੇਮ 'ਤੇ ਰੱਖੋ ਅਤੇ ਬੋਲਟਾਂ ਨੂੰ ਕੱਸੋ।
ਕਦਮ 5
- ਰਿਟਰਨ ਫਰੇਮ ਨੂੰ ਸਿੰਗਲ ਵਰਕਸਟੇਸ਼ਨ ਨਾਲ ਕਨੈਕਟ ਕਰੋ ਅਤੇ 2 ਹੈਂਡ ਬੋਲਟ ਨਾਲ ਫਿਕਸ ਕਰੋ।
- 2pcs ਪੇਚਾਂ M6x10 ਨਾਲ ਕੇਂਦਰ ਬਰੈਕਟਾਂ ਨੂੰ ਠੀਕ ਕਰੋ।
ਕਦਮ 6
- Mount the tabletop and fix it with24 pcs screws ST4x20;
- Fix the centre bracket with 2 pcs screws M6x10
ਕੇਬਲ ਟਰੇ ਇੰਸਟਾਲੇਸ਼ਨ
ਕਦਮ 1
- Fix the cable tray(B2-SSCT ) to the cable tray arms(HP-SSARM) with 8 pcs M6x10 screws.
ਕਦਮ 2
- 4 pcs M8x10 ਪੇਚਾਂ ਦੇ ਨਾਲ ਡੈਸਕ ਫਰੇਮ ਵਿੱਚ U ਬਰੈਕਟਾਂ ਨੂੰ ਸਥਾਪਿਤ ਕਰੋ।
- ਕੇਬਲ ਟਰੇ ਨੂੰ ਡੈਸਕ ਫਰੇਮ 'ਤੇ ਮਾਊਂਟ ਕਰੋ ਅਤੇ ਇਸਨੂੰ 6 ਪੀਸੀਐਸ M6x10 ਪੇਚਾਂ ਨਾਲ ਠੀਕ ਕਰੋ
Screen panel installation ( Shush30 Privacy Screen )
ਕਦਮ 1
- Insert the tapped plates to the screen panel ( plates can be found in B2-SBRAC carton)
ਕਦਮ 2
- Install the screen brackets ( B2-SBRAC )to the Shush30 Extrusion with 8 pcs M5x6 screws.
ਕਦਮ 3
- Fix the screen brackets ( B2-SBRAC ) to the desk frame with 10 pcs M6x10 screws.
EPS ( 900mm H Eco Panel ) Screen panel installation
ਕਦਮ 1
- Install the screen brackets(B2-SBRAC) on the cable tray arm (B2-SSARM)with 10 PCS M6x10Screws- Place 8 x Double Ended Bolts M5* 32mm – 6mm through The screen bracket ( B2-SBRAC) holesandthe holes you have created in the Eco Panel Screen. Tighten double ended bolt with AllenkeyThe brackets direction as photos display.
ਕਦਮ 2
- Place the EPS panel on the screen brackets Using a 6mm drill bit ( not included ), drill out holes in Eco Panel Screen in line with back to back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel )
- Place 8 x Double Ended Bolts M5* 32mm – 6mm through The screen bracket ( B2-SBRAC ) holes and the holes you have created in the Eco Panel Screen. Tighten double ended bolt with Allen key.
ਅਕਸਰ ਪੁੱਛੇ ਜਾਂਦੇ ਸਵਾਲ
How many components are included in the Halo Static Return Frame?
The Halo Static Return Frame includes various components such as table feet, columns, bolts, screws, side brackets, rubber pads, top frames, hand bolts, Allen wrenches, and cable ties.
How do I install the cable tray on the desk frame?
To install the cable tray, first fix it to the cable tray arms using provided screws M6x10. Then, attach U brackets to the desk frame with screws M8x10 and mount the cable tray, securing it with screws M6x10.
What is required for installing the Eco Panel Screen?
Installing the Eco Panel Screen requires screen brackets, double-ended bolts, a drill bit (not included), and a suitable Allen key for tightening.
ਦਸਤਾਵੇਜ਼ / ਸਰੋਤ
 |
HALO HAFH-RF Static Fixed Height Return Frame [pdf] ਹਦਾਇਤ ਮੈਨੂਅਲ HAFH-RF, HAFH-RF Static Fixed Height Return Frame, Static Fixed Height Return Frame, Fixed Height Return Frame, Height Return Frame |