INTELBRAS WC 7060 Series Access Controllers
उत्पादन सकियोview
उत्पादन मोडेलहरू
This document is applicable to the WC 7060 series access controllers. Table1-1 describes the WC 7060 series access controller models.
Table1-1 WC 7060 series access controller models
| उत्पादन श्रृंखला | उत्पादन कोड | मोडेल | टिप्पणीहरू |
| WC 7060 series | WC 7060 | WC 7060 | Non-PoE model |
प्राविधिक विनिर्देशहरू
Table1-2 Technical specifications
| वस्तु | निर्दिष्टीकरण |
| आयाम (H × W × D) | १88.1 × ×× × २ mm मिमी (.440..660 × 3.47 × ०.17.32 in in इन) |
| वजन | <22.9 kg (50.49 lb) |
| कन्सोल पोर्ट | 1, control port, 9600 bps |
| USB पोर्ट | १ (USB2) |
| व्यवस्थापन पोर्ट | 1 × 100/1000BASE-T management Ethernet port |
| मेमोरी | 64GB DDR4 |
| भण्डारण मिडिया | 32GB eMMC मेमोरी |
| रेटेड भोलtage सीमा |
|
| प्रणाली ऊर्जा खपत | <502 W |
| सञ्चालन तापमान | 0°C देखि 45°C (32°F देखि 113°F) |
| परिचालन आर्द्रता | 5% RH देखि 95% RH, noncondensing |
चेसिस views
WC 7060
अगाडि, पछाडि र साइड views
Figure1-1 Front view
| (1) USB ports | (2) Serial console port |
| (3) SHUT DOWN button LED | (4) Fan tray 1 |
| (5) Fan tray 2 | (6) Grounding screw (auxiliary grounding point 2) |
| (7) Power supply 4 | (8) Power supply 3 |
| (9) Power supply 2 | (10) Management Ethernet port |
| (11) Power supply 1 |
नोट:
Pressing the SHUT DOWN button LED for more than 15 milliseconds powers on the device. If you press and hold the button LED for more than 2 seconds, the LED is fast flashing at 1 Hz. You must wait for the device to notify the x86 operating system to shut down, and you can power off the device only when the LED turns off
| (1) Expansion slot 1 | (2) Expansion slot 2 |
| (3) Expansion slot 4 (reserved) | (4) Expansion slot 3 (reserved) |
The device comes with expansion slot 1 empty and the other expansion slots each installed with a filler panel. You can install expansion modules only in expansion slots 1 and 2. Expansion slots 3 and 4 are reserved. You can install one to two expansion modules for the device as required. In Figure1-2, expansion modules are installed in two expansion module slots.
The device comes with power supply slot PWR1 empty and the other three power supply slots each installed with a filler panel. One power supply can meet the power requirement of the device. You can also install two, three, or four power supplies for the device to achieve 1+1, 1+2, or 1+3 redundancy, respectively. In Figure1-1, four power supplies are installed in the power supply slots.
The device comes with the two fan tray slots empty. In Figure1-1, two fan trays are installed in the fan tray slots.
सावधानी:
- Do not hot swap expansion modules. Hot swapping expansion modules restarts the device. Please be cautious.
- To ensure adequate heat dissipation, you must install two fan trays for the device.
| (1) Fan tray handle | (2) Primary grounding point |
| (3) Auxiliary grounding point | (4) Power supply handle |
LED locations
The device in the following figures is fully configured with AC power supplies, fan trays, and expansion modules.
| (1) System status LED (SYS) | (2) Management Ethernet port LED (LINK/ACT) |
| (3) Power supply status LEDs (3, 4, 7, and 8) | (4) Fan tray status LEDs (5 and 6) |
| (1) 1000Base-T Ethernet port LEDs | (2) SFP port LEDs |
| (3) 10G SFP+ port LEDs | (4) 40G QSFP+ port LEDs |
हटाउन सकिने अवयवहरू
Removable components and compatibility matrixes
The access controllers use modular design. Table2-1 describes the compatibility matrix between access controllers and removable components.
Table2-1 Compatibility matrix between access controllers and removable components
| हटाउन सकिने अवयवहरू | WC 7060 |
| Removable power supplies | |
| LSVM1AC650 | समर्थित |
| LSVM1DC650 | समर्थित |
| Removable fan trays | |
| LSWM1BFANSCB-SNI | समर्थित |
| विस्तार मोड्युलहरू | |
| EWPXM1BSTX80I | समर्थित |
Table2-2 describes the compatibility matrix between expansion modules and expansion slots. Table2-2 Compatibility matrix between expansion modules and expansion slots
|
विस्तार मोड्युल |
WC 7060 | |
| स्लट १
स्लट १ |
स्लट १
स्लट १ |
|
| EWPXM1BSTX80I | समर्थित | N/A |
The power supplies support asset management. You can use display device manuinfo command to view the name, sequence number, and vendor of the power supply you have installed on the device.
बिजुली आपूर्ति
बिजुली आपूर्ति विनिर्देशहरू
चेतावनी!
When the device has power supplies in redundancy, you can replace a power supply without powering off the device. To avoid device damage and bodily injury, make sure the power supply is powered off before you replace it.
Table2-3 Power supply specifications
| विद्युत आपूर्ति मोडेल | वस्तु | निर्दिष्टीकरण |
|
PSR650B-12A1 |
उत्पादन कोड | LSVM1AC650 |
| मूल्याङ्कन गरिएको AC इनपुट भोल्युमtage सीमा | 100 देखि 240 VAC @ 50 वा 60 Hz | |
| आउटपुट भोल्युमtage | 12 V/5 V | |
| अधिकतम आउटपुट वर्तमान | 52.9 A (12 V) / 3 A (5 V) | |
| अधिकतम उत्पादन शक्ति | ७०० डब्ल्यू | |
| आयाम (H × W × D) | १40.2 × ×× × २ mm मिमी (.50.5..300 × 1.58 × ०.1.99 in in इन) | |
| सञ्चालन तापमान | -5°C देखि +50°C (23°F देखि 122°F) | |
| परिचालन आर्द्रता | 5% RH देखि 95% RH, noncondensing | |
|
PSR650B-12D1 |
उत्पादन कोड | LSVM1DC650 |
| मूल्याङ्कन गरिएको DC इनपुट भोल्युमtage सीमा | –40 to –60 VDC | |
| आउटपुट भोल्युमtage | 12 V/5 V | |
| अधिकतम आउटपुट वर्तमान | 52.9 A (12 V) / 3 A (5 V) | |
| अधिकतम उत्पादन शक्ति | ७०० डब्ल्यू | |
| आयाम (H × W × D) | १40.2 × ×× × २ mm मिमी (.50.5..300 × 1.58 × ०.1.99 in in इन) | |
| सञ्चालन तापमान | -5°C देखि +45°C (23°F देखि 113°F) | |
| परिचालन आर्द्रता | 5% RH देखि 95% RH, noncondensing |
बिजुली आपूर्ति views
| (१)) कुंडी | (2) स्थिति एलईडी |
| (3) Power input receptacle | (4) ह्यान्डल |
फ्यान ट्रेहरू
Fan tray specifications
Table2-4 Fan tray specifications
| Fan tray model | वस्तु | निर्दिष्टीकरण |
|
LSWM1BFANSCB-SNI |
आयाम (H × W × D) | १80 × ×× × २ mm मिमी (.80..232.6 × 3.15 × ०.3.15 in in इन) |
| वायु प्रवाह दिशा | Air exhausted from the fan tray faceplate | |
| फ्यानको गति | 13300 RPM | |
| अधिकतम हावा प्रवाह | १५४३ CFM (४०.८ m120/मिनेट) | |
| परिचालन भोल्युमtage | १२ वी | |
| अधिकतम शक्ति खपत | ७०० डब्ल्यू | |
| सञ्चालन तापमान | 0°C देखि 45°C (32°F देखि 113°F) | |
| परिचालन आर्द्रता | 5% RH देखि 95% RH, noncondensing | |
| भण्डारण तापमान | -40°C देखि +70°C (-40°F देखि +158°F) | |
| भण्डारण आर्द्रता | 5% RH देखि 95% RH, noncondensing |
फ्यान ट्रे views 
विस्तार मोड्युलहरू
Expansion module specifications
Table2-5 Expansion module specifications 
विस्तार मोड्युल views
| (1) 1000BASE-T Ethernet ports | (2) 1000BASE-X-SFP fiber ports |
| (3) 10GBASE-R-SFP+ fiber ports | (4) 40GBASE-R-QSFP+ fiber ports |
पोर्ट र LEDs
पोर्टहरू
कन्सोल पोर्ट
| वस्तु | निर्दिष्टीकरण |
| कनेक्टर प्रकार | RJ-45 |
| अनुरूप मानक | EIA/TIA-232 |
| Port transmission rate | 9600 bps |
|
सेवाहरू |
|
| मिल्दो मोडेलहरू | WC 7060 |
USB पोर्ट
Table3-2 USB port specifications
| वस्तु | निर्दिष्टीकरण |
| इन्टरफेस प्रकार | USB 2.0 |
| अनुरूप मानक | OHCI |
| Port transmission rate | Uploads and downloads data at a rate up to 480 Mbps |
| कार्य र सेवाहरू | पहुँच गर्दछ file system on the flash of the device, for example, to upload or download application and configuration files |
| मिल्दो मोडेलहरू | WC 7060 |
नोट:
USB devices from different vendors vary in compatibilities and drivers. INTELBRAS does not guarantee correct operation of USB devices from other vendors on the device. If a USB device fails to operate on the device, replace it with one from another vendor.
SFP पोर्ट
| वस्तु | निर्दिष्टीकरण |
| कनेक्टर प्रकार | LC |
| मिल्दो | GE SFP transceiver modules in Table3-4 |
| वस्तु | निर्दिष्टीकरण |
| transceiver modules | |
| मिल्दो मोडेलहरू | EWPXM1BSTX80I |
Table3-4 GE SFP transceiver modules
| ट्रान्सीभर मोड्युल प्रकार |
ट्रान्सीभर module model |
केन्द्रीय wavele ngth |
प्राप्तकर्ता संवेदनशीलता |
फाइबर व्यास |
डाटा दर |
अधिकतम transmis sion दूरी |
|
GE multi-mode module |
SFP-GE-SX-MM850
-A |
८५० एनएम | -17 dBm | ५० µm | 1.25 Gbps | १५ मि
(२१०.०० फिट) |
| SFP-GE-SX-MM850
-D |
८५० एनएम | -17 dBm | ५० µm | 1.25 Gbps | १५ मि
(२१०.०० फिट) |
|
|
GE single-mode module |
SFP-GE-LX-SM131 0-A |
८५० एनएम |
-20 dBm |
५० µm |
1.25 Gbps |
४० किमी
(१०.० माइल) |
| SFP-GE-LX-SM131 0-D |
८५० एनएम |
-20 dBm |
५० µm |
1.25 Gbps |
४० किमी
(१०.० माइल) |
नोट:
- As a best practice, use INTELBRAS transceiver modules for the device.
- The INTELBRAS transceiver modules are subject to change over time. For the most recent list of INTELBRAS transceiver modules, contact your INTELBRAS Support or marketing staff.
- For more information about INTELBRAS transceiver modules, see INTELBRAS
- Transceiver Modules User Guide.
SFP+ पोर्ट
Table3-5 SFP+ port specifications
| वस्तु | निर्दिष्टीकरण |
| कनेक्टर प्रकार | LC |
| Compatible transceiver modules and cables | 10GE SFP+ transceiver modules and cables in Table 3- 6 |
| मिल्दो उपकरणहरू | EWPXM1BSTX80I |
Table3-6 10GE SFP+ transceiver modules and cables
|
ट्रान्सीभर module or cable type |
ट्रान्सीभर module or cable model |
Central wavele ngth |
प्राप्तकर्ता संवेदनशीलता |
फाइबर व्यास |
डाटा दर |
अधिकतम ट्रान्समी ssion distanc e |
| 10GE
multi-mode module |
SFP-XG-SX-MM850
-A |
८५० एनएम | -9.9dBm | ०.७६२µm | 10.31Gb/s | १० मि |
| SFP-XG-SX-MM850 | ८५० एनएम | -9.9 dBm | ५० µm | 10.31 Gbps | १५ मि |
|
ट्रान्सीभर module or cable type |
ट्रान्सीभर module or cable model |
केन्द्रीय wavele ngth |
प्राप्तकर्ता संवेदनशीलता |
फाइबर व्यास |
डाटा दर |
अधिकतम ट्रान्समी ssion distanc e |
| -D | (१०.०
फिट) |
|||||
| SFP-XG-SX-MM850
-E |
८५० एनएम |
-9.9 dBm |
५० µm |
10.31 Gbps |
१५ मि
(१०.० फिट) |
|
| 10GE
single-mode module |
SFP-XG-LX-SM131 0 | ८५० एनएम | -14.4dBm | ०.७६२µm | 10.31Gb/s | 10 किमी |
| SFP-XG-LX-SM131 0-D |
८५० एनएम |
-14.4 dBm |
५० µm |
10.31 Gbps |
४० किमी
(१०.० माइल) |
|
| SFP-XG-LX-SM131 0-E |
८५० एनएम |
-14.4 dBm |
५० µm |
10.31 Gbps |
४० किमी
(१०.० माइल) |
|
| SFP+ केबल | LSWM3STK को परिचय | N/A | N/A | N/A | N/A | ४.३ मिटर (१४.११०
फिट) |
| (1) कनेक्टर | (2) Pull latch |
नोट:
- As a best practice, use INTELBRAS transceiver modules and cables for the device.
- The INTELBRAS transceiver modules and cables are subject to change over time. For the most recent list of INTELBRAS transceiver modules and cables, contact your INTELBRAS Support or marketing staff.
- For more information about INTELBRAS transceiver modules and cables, see INTELBRAS Transceiver Modules User Guide.
QSFP+ port
Table3-7 QSFP+ port specifications
| वस्तु | निर्दिष्टीकरण |
| कनेक्टर प्रकार | LC: QSFP-40G-LR4L-WDM1300, QSFP-40G-LR4-WDM1300, QSFP-40G-BIDI-SR-MM850 MPO: QSFP-40G-CSR4-MM850, QSFP-40G-SR4-MM850 |
| Compatible transceiver modules and cables |
QSFP+ transceiver modules and cables in Table 3- 8 |
| मिल्दो मोडेलहरू | EWPXM1BSTX80I |
Table3-8 QSFP+ transceiver modules and cables 
- As a best practice, use INTELBRAS transceiver modules and cables for the device.
- The INTELBRAS transceiver modules and cables are subject to change over time. For the most recent list of INTELBRAS transceiver modules and cables, contact your INTELBRAS Support or marketing staff.
- For more information about INTELBRAS transceiver modules and cables, see INTELBRAS Transceiver Modules User Guide.
100/1000BASE-T management Ethernet port
Table3-9 100/1000BASE-T management Ethernet port specifications
| वस्तु | निर्दिष्टीकरण |
| कनेक्टर प्रकार | RJ-45 |
| Rate, duplex mode, and auto-MDI/MDI-X |
|
| प्रसारण माध्यम | Category 5 or above twisted pair cable |
| अधिकतम प्रसारण दूरी | १५.२ मि (५० फिट) |
| अनुरूप मानक | IEEE 802.3i, 802.3u, 802.3ab |
| कार्य र सेवाहरू | Device software and Boot ROM upgrade, network management |
| मिल्दो मोडेलहरू | WC 7060 |
1000BASE-T इथरनेट पोर्ट
Table3-10 1000BASE-T Ethernet port specifications
| वस्तु | निर्दिष्टीकरण |
| कनेक्टर प्रकार | RJ-45 |
| Auto-MDI/MDI-X | MDI/MDI-X autosensing |
| अधिकतम प्रसारण दूरी | १५.२ मि (५० फिट) |
| प्रसारण माध्यम | Category 5 or above twisted pair cable |
| अनुरूप मानक | आईईईई 802.3ab |
| मिल्दो मोडेलहरू | EWPXM1BSTX80I |
Combo interface
The 1000BASE-T Ethernet ports and 1000BASE-X-SFP fiber ports on the EWPXM1BSTX80I expansion module are combo interfaces. Do not use 10GBASE-R-SFP+ fiber ports and 40GBASE-R-QSFP+ fiber ports simultaneously.
LEDs
WC 7060 device port status LEDs
प्रणाली स्थिति एलईडी
The system status LED shows the operating status of the device. Table3-11 System status LED description
| एलईडी चिन्ह | स्थिति | विवरण |
| SYS | Fast flashing green (4 Hz) | प्रणाली सुरु हुँदैछ। |
| Slow flashing green (0.5 Hz) | The system is operating correctly. | |
| स्थिर रातो | A critical alarm has been triggered, for example, power supply alarm, fan tray alarm, high temperature alarm, and software loss. | |
| बन्द | The device has not started up. |
100/1000BASE-T management Ethernet port LED
Table3-12 100/1000BASE-T management Ethernet port LED description
| एलईडी स्थिति | विवरण |
| स्थिर हरियो | बिजुली आपूर्ति ठीकसँग चलिरहेको छ। |
| हरियो चम्किरहेको | The power supply has power input but is not installed on the device. |
| स्थिर रातो | The power supply is faulty or has entered protection state. |
| Red/green flashing alternatively | The power supply has generated an alarm for power issues (such as output overcurrent, output overload, and overtemperature), but has not entered protection state. |
| रातो चम्किरहेको | The power supply does not have power input. The device is installed with two power supplies. If one has power input, but the other does not, the status LED on the power supply that does not have power input flashes red. The power supply has entered input undervoltagई सुरक्षा राज्य। |
| बन्द | The power supply does not have power input. |
Status LED on a fan tray
The LSWM1BFANSCB-SNI fan tray provides a status LED to indicate its operating status.
Table3-14 Description for the status LED on a fan tray
| एलईडी स्थिति | विवरण |
| On | The fan tray is operating incorrectly. |
| बन्द | फ्यान ट्रे ठीकसँग काम गरिरहेको छ। |
Port LED on an expansion module
Table3-15 Description for port LEDs on an expansion module
| एलईडी | स्थिति | विवरण |
| 1000BASE-T Ethernet port LED | स्थिर हरियो | A 1000 Mbps link is present on the port. |
| हरियो चम्किरहेको | The port is receiving or sending data at 1000 Mbps. | |
| बन्द | पोर्टमा कुनै लिङ्क छैन। | |
| SFP fiber port LED | स्थिर हरियो | A 1000 Mbps link is present on the port. |
| हरियो चम्किरहेको | The port is receiving or sending data at 1000 Mbps. | |
| बन्द | पोर्टमा कुनै लिङ्क छैन। | |
| 10G SFP+ port LED | स्थिर हरियो | A 10 Gbps link is present on the port. |
| हरियो चम्किरहेको | The port is receiving or sending data at 10 Gbps. | |
| बन्द | पोर्टमा कुनै लिङ्क छैन। | |
| 40G QSFP+ port LED | स्थिर हरियो | A 40 Gbps link is present on the port. |
| हरियो चम्किरहेको | The port is receiving or sending data at 40 Gbps. | |
| बन्द | पोर्टमा कुनै लिङ्क छैन। |
शीतलन प्रणाली
To dissipate heat timely and enhance system stability, the device uses a high-performance cooling system. Consider the site ventilation design when you plan the installation site for the device.
Table4-1 Cooling system
| उत्पादन श्रृंखला | उत्पादन मोडेल | वायु प्रवाह दिशा |
| WC 7060 series | WC 7060 | The device uses a front-rear air aisle. It can provide airflow from the port side to the power supply side by using fan trays. See Figure4-1. |
कागजातहरू / स्रोतहरू
 |
INTELBRAS WC 7060 Series Access Controllers [pdf] मालिकको म्यानुअल WC 7060, WC 7060 Series Access Controllers, WC 7060 Series, Access Controllers, Controllers |
